Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1927

Distribution of Pressure Over Model of the Upper Wing and Aileron of a Fokker D-VII Airplane

This report describes tests made for the purpose of determining the distribution of pressure over a model of the tapered portion of the upper wing and the aileron of a Fokker D-VII Airplane. Normal pressures were measured simultaneously at 74 points distributed over the wing and aileron. Tests were made throughout the useful range of angles of attack with aileron setting ranging from -20 degrees to +20 degrees. The results are presented graphically. It was found that the pressure distribution along the chord is in general similar to that of thick tapered airfoils previously tested. The maximum resultant pressure recorded was five times the dynamic pressure. The distribution of the air load along the span may be assumed to be uniform for design purposes. Aileron displacements affect the pressures forward to the leading edge of the wing and may increase the air load on the outer portion of the wing by a considerable amount. With the wing at large angles of attack, the overhanging portion of the aileron creates usually a burble flow and therefore a large drag. The balance reduces the control stick forces at small angles of attack for all aileron displacements. At large angles of attack it does this for small displacements only. With the airplane at its maximum speed, an angle of attack of 18 degrees, and a down aileron displacement of 20 degrees, the bending moment tending to break off the overhanging portion of the aileron will be greater than that caused by a uniform static load of 35 pounds per square foot.

Fairbanks, A J↗
NASA NTRS1930

Tests of Five Metal Model Propellers with Various Pitch Distributions in a Free Wind Stream and in Combination with Model VE-7 Fuselage

This report describes the tests of five adjustable blade metal model propellers both in a free wind stream and in combination with a model fuselage with stub wings. The propellers are of the same form and cross section but have variations in radial distributions of pitch. By making a survey of the radial distribution of air velocity through the propeller plane of the model fuselage it was found that this velocity varies from zero at the hub center to approximately free stream velocity at the blade tip. The tests show that the efficiency of a propeller when operating in the presence of the airplane is, over the working range, generally less than when operating in a free wind stream, but that a propeller with a radial distribution of pitch of the same nature as the radial distribution of air velocity through the propeller plane suffers the smallest loss in efficiency.

Lesley, E P↗
NASA NTRS1937

Pressure-Distribution Measurements on O-2H Airplane in Flight

Results are given of pressure-distribution measurements made over two different horizontal tail surfaces and the right wing cellule, including the slipstream area, of an observation-type biplane. Measurements were also taken of air speed, control-surface positions, control-stick forces, angular velocities, and accelerations during various abrupt maneuvers. These maneuvers consisted of push-downs and pull-ups from level flight, dive pull-outs, and aileron rolls with various thrust conditions. The results from the pressure-distribution measurements over the wing cellule are given on charts showing the variation of individual rib coefficients with wing coefficients; the data from the tail-surface pressure-distribution measurements are given mainly as total loads and moments. These data are supplemented by time histories of the measured quantities and isometric views of the rib pressure distributions occurring in abrupt maneuvers.

Pearson, H A↗
NASA NTRS1938

Calculation of the chordwise load distribution over airfoil sections with plain, split, or serially hinged trailing-edge flaps

A method is presented for the rapid calculation of the incremental chordwise normal-force distribution over an airfoil section due to the deflection of a plain flap or tab, a split flap, or a serially hinged flap. This report is intended as a supplement to NACA Report no. 631, wherein a method is presented for the calculation of the chordwise normal-force distribution over an airfoil without a flap or, as it may be considered, an airfoil with flap (or flaps) neutral. The method enables the determination of the form and magnitude of the incremental normal-force distribution to be made for an airfoil-flap combination for which the section characteristics have been determined. A method is included for the calculation of the flap normal-force and hinge-moment coefficients without necessitating a determination of the normal-force distribution.

Allen, H Julian↗
NASA NTRS1939

Tests of Two Full-Scale Propellers with Different Pitch Distributions, at Blade Angles up to 60 Degrees

Two 3-blade 10-foot propellers were operated in front of a liquid-cooled engine nacelle. The propellers differed only in pitch distribution; one had normal distribution (nearly constant pitch for a blade angle of 15 degrees at 0.75 radius), and the other had the pitch of the tip sections decreased with respect to that for the shank sections (blade angle of 35 degrees for nearly constant pitch distribution). Propeller blade angles at 0.75r from 15 degrees to sixty degrees, corresponding to design speeds up to 500 miles per hour, were investigated. Propeller blade angles at 0.75r from 15 degrees to 60 degrees, corresponding to design speeds up to 500 miles per hour, were investigated. The results indicated that the propulsive efficiency at a blade angle of 60 degrees was about 9 percent less than the maximum value of 86 percent, which occurred at blade angle of about 30 degrees. The efficiency at a blade angle of 60 degrees was increased about 7 percent by correcting for the effect of a spinner and, at a blade angle of 30 degrees about 3 percent. The peak efficiencies for the propeller having the washed-out pitch distribution were slightly less than for the normal propeller but the take-off efficiency was generally higher.

Biermann, David↗
NASA NTRS1950

Method of designing cascade blades with prescribed velocity distributions in compressible potential flows

By use of the assumption that the pressure-volume relation is linear, a solution to the problem of designing a cascade for a given turning and with a prescribed velocity distribution along the blade in a potential flow of a compressible perfect fluid was obtained by a method of correspondence between potential flows of compressible and incompressible fluids. The designing of an isolated airfoil with a prescribed velocity distribution along the airfoil is considered as a special case of cascade. If the prescribed velocity distribution is not theoretically attainable, the method provides a means of modifying the distribution so as to obtain a physically significant blade shape. Numerical examples are included.

Costello, George R↗
NASA NTRS1955

Calculated spanwise lift distributions, influence functions, and influence coefficients for unswept wings in subsonic flow

Spanwise lift distributions have been calculated for nineteen unswept wings with various aspect ratios and taper ratios and with a variety of angle-of-attack or twist distributions, including flap and aileron deflections, by means of the Weissinger method with eight control points on the semispan. Also calculated were aerodynamic influence coefficients which pertain to a certain definite set of stations along the span, and several methods are presented for calculating aerodynamic influence functions and coefficients for stations other than those stipulated. The information presented in this report can be used in the analysis of untwisted wings or wings with known twist distributions, as well as in aeroelastic calculations involving initially unknown twist distributions.

Diederich, Franklin W↗
NASA NTRS1948

Surface-pressure Distributions on a Systematic Group of NACA 1-series Cowlings with and Without Spinners

A method for calculating the flow fields of axially symmetric bodies from their pressure distributions is reported in NACA RM No. L8I17. In order to facilitate application of this method to the important case of the cowling-spinner combination, for use in the design of propellers, the present paper presents static-pressure distributions on the tops of 79 high-critical-speed NACA 1-series cowling-spinner combinations over wide ranges of inlet-velocity ratio at angles of attack of 0 degrees, 2 degrees, 4 degrees, and 6 degrees. Static-pressure distributions around the nose sections of several cowlings are given in greater detail to aid in estimating the pressures near the stagnation points and to show the effect of changes in the internal lip shape. The effects of the operation of a typical propeller on the surface pressures on the cowling are shown for one configuration. The pressure distributions over the nine NACA 1-series nose inlets used as the basic components of these combinations are also presented ro supplement the existing open-nose-cowling data of NACA ACR No. L5F30a which are applicable to the case of the rotating cowling.

Boswinkle, Robert W JR↗
NASA NTRS1951

Investigation of Turbine-outlet Temperature Distribution of XJ34-WE-32 Turbojet Engine

Turbine-outlet radial temperature distributions of an XJ34-WE-32 turbojet engine were investigated in the altitude wind tunnel at the NACA Lewis laboratory over a range of pressure altitudes, engine-inlet air temperatures and flight Mach numbers at or near rated engine conditions. From blade stress considerations, the turbine-outlet temperature distribution was considered satisfactory at altitudes up to 25,000 feet at corrected engine speeds corresponding to rated speed (12,500 rpm); however, operation at either higher corrected engine speeds or higher altitudes resulted in an inversion of the turbine temperature distribution that was detrimental to turbine life. Installation of a compressor-outlet mixer greatly improved the turbine radial temperature distribution.

Prince, W R↗
NASA NTRS1942

Pressure distribution on wings in reversed flow

The series of pressure distribution measurements at three test sections on NACA airfoils 2212 and M6 within 170 to 210 angles of attack in reversed flow proved to be largely independent of the profile form. In contradiction to the pressure distribution in normal flow considerable negative pressure from the upper surface spills over onto the lower surface, and vice versa, even in the zone of sound flow. The results are presented as chord-wise pressure and load distribution. The spanwise lift distribution and the total lift coefficients of the wing obtained by integration manifest approximate agreement with the behavior of a diagonally disposed flat plate. By consideration of the ground effect (represented by a flat wall) the lower surface of the wing shows an increase in the low pressure.

Naumann, A↗
NASA NTRS1990

Concepts in distributed planning, scheduling, and control

To support instrument and experiment operations effectively in the Space Station era, planning, scheduling, and control must allow for: (1) interactive real-time remote operations; (2) responsive scheduling and rescheduling; (3) support of the full range of distributed science, application and commercial users; (4) interaction and cooperation among distributed users; and (5) efficient use of often onboard, communications, and ground-based resources. We suggest conceptual and managerial approaches that address these needs. Specifically, we describe approaches to distributed planning, scheduling and control functions that are based on resources and on a distributed knowledge hierarchy. We describe the scheduling functions as the component of the integrated space-ground Operations Management System. We include the integration of the planning and scheduling functions with the real-time operations control system, and we discuss automated scheduling assistants. These suggested approaches, taken from the users' point-of-view, have resulted in two prototype systems: Operations and Science Instrument Support package and Science User Resource Planning and Scheduling System.

Hansen, Elaine↗
NASA NTRS1993

Distributed simulation using a real-time shared memory network

The Advanced Control Technology Branch of the NASA Lewis Research Center performs research in the area of advanced digital controls for aeronautic and space propulsion systems. This work requires the real-time implementation of both control software and complex dynamical models of the propulsion system. We are implementing these systems in a distributed, multi-vendor computer environment. Therefore, a need exists for real-time communication and synchronization between the distributed multi-vendor computers. A shared memory network is a potential solution which offers several advantages over other real-time communication approaches. A candidate shared memory network was tested for basic performance. The shared memory network was then used to implement a distributed simulation of a ramjet engine. The accuracy and execution time of the distributed simulation was measured and compared to the performance of the non-partitioned simulation. The ease of partitioning the simulation, the minimal time required to develop for communication between the processors and the resulting execution time all indicate that the shared memory network is a real-time communication technique worthy of serious consideration.

Simon, Donald L.↗
NASA NTRS1993

A wide-band fiber optic frequency distribution system employing thermally controlled phase compensation

An active wide-band fiber optic frequency distribution system employing a thermally controlled phase compensator to stabilize phase variations induced by environmental temperature changes is described. The distribution system utilizes bidirectional dual wavelength transmission to provide optical feedback of induced phase variations of 100 MHz signals propagating along the distribution cable. The phase compensation considered differs from earlier narrow-band phase compensation designs in that it uses a thermally controlled fiber delay coil rather than a VCO or phase modulation to compensate for induced phase variations. Two advantages of the wide-band system over earlier designs are (1) that it provides phase compensation for all transmitted frequencies, and (2) the compensation is applied after the optical interface rather than electronically ahead of it as in earlier schemes. Experimental results on the first prototype shows that the thermal stabilizer reduces phase variations and Allan deviation by a factor of forty over an equivalent uncompensated fiber optic distribution system.

Johnson, Dean↗
NASA NTRS1993

A distributed version of the NASA Engine Performance Program

Distributed NEPP, a version of the NASA Engine Performance Program, uses the original NEPP code but executes it in a distributed computer environment. Multiple workstations connected by a network increase the program's speed and, more importantly, the complexity of the cases it can handle in a reasonable time. Distributed NEPP uses the public domain software package, called Parallel Virtual Machine, allowing it to execute on clusters of machines containing many different architectures. It includes the capability to link with other computers, allowing them to process NEPP jobs in parallel. This paper discusses the design issues and granularity considerations that entered into programming Distributed NEPP and presents the results of timing runs.

Cours, Jeffrey T.↗
NASA NTRS1993

Data distribution

A discussion of data distribution is presented in vugraph form. The following topics are discussed: data distribution from the perspective of Earth observations and the end user; problems associated with synthetic aperture radar (SAR) data distribution; and future data distribution techniques.

Hilland, J. E.↗
NASA NTRS1992

External calibration of polarimetric radar images using distributed targets

A new technique is presented for calibrating polarimetric synthetic aperture radar (SAR) images using only the responses from natural distributed targets. The model for polarimetric radars is assumed to be X = cRST where X is the measured scattering matrix corresponding to the target scattering matrix S distorted by the system matrices T and R (in general T does not equal R(sup t)). To allow for the polarimetric calibration using only distributed targets and corner reflectors, van Zyl assumed a reciprocal polarimetric radar model with T = R(sup t); when applied for JPL SAR data, a heuristic symmetrization procedure is used by POLCAL to compensate the phase difference between the measured HV and VH responses and then take the average of both. This heuristic approach causes some non-removable cross-polarization responses for corner reflectors, which can be avoided by a rigorous symmetrization method based on reciprocity. After the radar is made reciprocal, a new algorithm based on the responses from distributed targets with reflection symmetry is developed to estimate the cross-talk parameters. The new algorithm never experiences problems in convergence and is also found to converge faster than the existing routines implemented for POLCAL. When the new technique is implemented for the JPL polarimetric data, symmetrization and cross-talk removal are performed on a line-by-line (azimuth) basis. After the cross-talks are removed from the entire image, phase and amplitude calibrations are carried out by selecting distributed targets either with azimuthal symmetry along the looking direction or with some well-known volume and surface scattering mechanisms to estimate the relative phases and amplitude responses of the horizontal and vertical channels.

Yueh, Simon H.↗
NASA NTRS1993

A comparison of queueing, cluster and distributed computing systems

Using workstation clusters for distributed computing has become popular with the proliferation of inexpensive, powerful workstations. Workstation clusters offer both a cost effective alternative to batch processing and an easy entry into parallel computing. However, a number of workstations on a network does not constitute a cluster. Cluster management software is necessary to harness the collective computing power. A variety of cluster management and queuing systems are compared: Distributed Queueing Systems (DQS), Condor, Load Leveler, Load Balancer, Load Sharing Facility (LSF - formerly Utopia), Distributed Job Manager (DJM), Computing in Distributed Networked Environments (CODINE), and NQS/Exec. The systems differ in their design philosophy and implementation. Based on published reports on the different systems and conversations with the system's developers and vendors, a comparison of the systems are made on the integral issues of clustered computing.

Kaplan, Joseph A.↗
NASA NTRS1993

In-flight pressure distributions and skin-friction measurements on a subsonic transport high-lift wing section

Flight experiments are being conducted as part of a multiphased subsonic transport high-lift research program for correlation with wind-tunnel and computational results. The NASA Langley Transport Systems Research Vehicle (B737-100 aircraft) is used to obtain in-flight flow characteristics at full-scale Reynolds numbers to contribute to the understanding of 3-D high-lift, multi-element flows including attachment-line transition and relaminarization, confluent boundary-layer development, and flow separation characteristics. Flight test results of pressure distributions and skin friction measurements were obtained for a full-chord wing section including the slat, main-wing, and triple-slotted, Fowler flap elements. Test conditions included a range of flap deflections, chord Reynolds numbers (10 to 21 million), and Mach numbers (0.16 to 0.40). Pressure distributions were obtained at 144 chordwise locations of a wing section (53-percent wing span) using thin pressure belts over the slat, main-wing, and flap elements. Flow characteristics observed in the chordwise pressure distributions included leading-edge regions of high subsonic flows, leading-edge attachment-line locations, slat and main-wing cove-flow separation and reattachment, and trailing-edge flap separation. In addition to the pressure distributions, limited skin-friction measurements were made using Preston-tube probes. Preston-tube measurements on the slat upper surface suggested relaminarization of the turbulent flow introduced by the pressure belt on the slat leading-edge surface when the slat attachment line was laminar. Computational analysis of the in-flight pressure measurements using two-dimensional, viscous multielement methods modified with simple-sweep theory showed reasonable agreement. However, overprediction of the pressures on the flap elements suggests a need for better detailed measurements and improved modeling of confluent boundary layers as well as inclusion of three-dimensional viscous effects in the analysis.

Yip, Long P.↗