Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Computed Tomography”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Damage evolution and ductile fracture of commercially-pure titanium sheets subjected to simple tension and cyclic bending under tension

This paper describes a study into the evolution of damage in commercial-purity titanium (CP–Ti) sheets subjected to cyclic bending under tension (CBT) and uniaxial tension (simple tension, ST). Sections were taken from sheets that were strained to various levels under both methods and were imaged using X-ray computed tomography (XCT) to reveal insights into the size, density, and distribution of microvoids in the sheets. Digital image correlation (DIC) was also used to observe the surface strain of CBT and ST sheets during testing. These results showed that elongation to failure (ETF) for CBT deformation is about 2.5× higher than for ST, local longitudinal strains in the bulk of the CBT sample are around 1.3× higher than the peak strain in the ST necked region, and 1.7× higher in the localized region of CBT failure. It was found that the volume-density of voids in both sheets followed a similar exponential increase with strain, reaching nearly 45× higher in the CBT than the ST sheets before the onset of failure, mainly due to the higher strain levels achieved. A higher volume density of voids developed in the center of sheets at high levels of strain, for both processes, with the density in the sheet center becoming approximately double that found near the edges. Scanning electron microscopy (SEM) was used to examine the fracture surface of CBT and ST sheets after failure. The observations are presented and discussed highlighting the CBT process as effective to delay ductile fracture of the CP-Ti sheets.

Commercially pure titanium↗
DOE OSTI2020

Role of microstructure on CO corrosion of SiC layer in UO₂-TRISO fuel

The Advanced Gas Reactor Fuel Qualification and Development (AGR) program has focused on qualification of UCO kernel tristructural-isotropic (TRISO) particle fuel relative to UO₂ kernel TRISO particle fuel. However, a UO₂ kernel variant was included in the second AGR irradiation experiment (AGR-2) for comparison and to connect to historic fuel irradiation data. The development of a multiscale, post-irradiation examination (PIE) analysis approach through the AGR Program has allowed for a comprehensive understanding of individual particle failure. This approach has been applied to gain an understanding of SiC layer failure in UO₂ kernel TRISO fuel from AGR-2 after safety testing at 1600–1700 °C. Particle failure by intergranular CO corrosion, facilitated by a compromised inner pyrolytic carbon layer, has been confirmed through the combined application of modern x-ray computed tomography and electron microscopy techniques. In addition, a relationship between grain boundary character and CO corrosion has been identified. This finding provides an opportunity to develop mitigating strategies to improve the resilience of the SiC layer to CO corrosion in UO₂ TRISO fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Postirradiation examination from separate effects irradiation testing of uranium nitride kernels and coated particles

An overview of postirradiation examination results for uranium nitride kernels and uranium nitride coated particles irradiated in the High Flux Isotope Reactor are presented. This is the first postirradiation examination of the MiniFuel irradiation vehicle that was recently developed to rapidly accumulate burnup during separate effects irradiation testing. In general, the burnup and fuel temperatures measured postirradiation were consistent with the design calculations. The burnup measured by mass spectrometry ranged from 5.9 to 10 MWd/kgU and was achieved after only 68 effective full-power days of irradiation. The dilatometric evaluation of passive silicon carbide thermometry indicated that the fuel was irradiated at temperatures ranging from 410 to 460 °C. Because the irradiation temperatures and burnup were low, the UN kernels showed minimal fission gas release that was within the range of the expected recoil (athermal) release. While it is possible to measure fuel swelling using x-ray computed tomography, the observed swelling was too small to quantify in this case. Extensive microstructural characterization of the irradiated fuel was performed in this study, and no significant irradiation induced changes were observed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Investigation of the irradiation effects in additively manufactured 316L steel resulting in decreased irradiation assisted stress corrosion cracking susceptibility

While additive manufacturing (AM) is an area of increasing interest to the nuclear industry, there are significant research and development needs prior to successful implementation of additively manufactured components into reactors. AM steel behaves differently than traditional wrought material, as has been observed in numerous mechanical testing studies. The nuclear industry must also understand the material response to irradiation. This work examines the irradiation damage and the irradiation assisted stress corrosion cracking behavior (IASCC) of both proton irradiated AM and wrought 316L steel. For IASCC testing, specimens were strained to 4% plastic strain in a simulated boiling water reactor environment (288°C, 0.2 µS/cm). Transmission and scanning electron microscopy, confocal microscopy, and X-ray computed tomography were used to examine coupons of the material as well as tensile bars used in the IASCC testing. This work found that the wrought 316L was more susceptible to IASCC than the AM steel, however, some IASCC was observed in the AM steel when tested with the tensile axis parallel to the build direction. Electron microscopy has shown significantly fewer radiation induced voids formed in the AM steel. While the pre-existing pore network in the AM steel may act as a sink to point defects, this is not expected to be the major factor in the reduced swelling observed in the AM steel. The lower density of radiation induced voids was expected to contribute to the IASCC resistance by decreasing the localization of deformation in the irradiated specimens, however, severity of localized deformation in AM steel, measured in dislocation channel spacing and height, was similar or more severe to that found in wrought. In conclusion, the presence of severe cracking in the wrought specimens did not allow for a direct comparison of localized deformation severities between the AM and wrought steel.

Additive manufacturing↗
DOE OSTI2023

Failure analysis of nuclear transient-tested UN tristructural isotropic fuel particles in a 3D printed SiC matrix

Fully ceramic microencapsulated fuel elements containing UN tristructural isotropic (TRISO) fuel particles within a 3D printed SiC matrix were subjected to transient testing with varying energy depositions. Detailed post-irradiation examinations were performed, including leaching in hot HNO3 and post-leaching X-ray computed tomography, to quantify the percentage of failed TRISO particles and crack propagation within the particles and surrounding fuel matrix. In parallel, detailed finite element analyses were performed for comparison with experimental findings and to better evaluate transient failure modes. The lowest transient energy deposition—which still exceeded bounding values for high-temperature gas-cooled reactor applications—resulted in no detectable TRISO particle failures or matrix cracking, which was consistent with the simulations. Simulations of the higher-energy transients for which significant TRISO particle failure was expected were generally able to reproduce the transient temperatures and matrix cracking. Thus, the TRISO particle failures were explained based on the effects of local SiC matrix thickness and porosity. Results generally confirmed the high strength of the additively manufactured SiC matrix but also affirmed the need for a modified UN TRISO architecture to prevent SiC matrix cracks from propagating through TRISO layers. This unique failure mode has not historically been considered for TRISO fuels contained in weaker graphite matrices.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Internal short circuit and failure mechanisms of lithium-ion pouch cells under mechanical indentation abuse conditions: An experimental study

Electromechanical structural integrity and thermal stability dictate the safety performance of lithium-ion batteries. Progressive deformation and failure across microscopic and macroscopic lengths scales that are responsible for internal short circuit (ISC) in lithium-ion cells under mechanical abuse conditions remains elusive. In this study, a series of indentation tests were conducted on lithium-ion cells with different capacities up to the occurrence of ISC. The external response and internal configuration of these cells were investigated. It is discovered that cells with different capacities and state of charges exhibited different behaviors. Maximum temperature, which is often regarded as the most important parameter related to thermal runaway (TR), varied considerably due to the complicated contact configurations. X-ray computed tomography (XCT) showed that ISC was a collective result of shear band or other strain-localization modes in the electrode assembly, shear offsets in the granular coatings of electrodes, and the accompanying ductile fracture in the metal foils. We believe that the irregular strain-localization modes (kinks, cusps, and buckles), radical mismatches in mechanical properties of different layers, and geometric features of the indenter eventually lead to the tearing/puncture of cell separator at various locations. Furthermore, the results could provide useful guidance for the micromechanical modeling of lithium-ion cells.

25 ENERGY STORAGE↗
DOE OSTI2020

Investigation on capacity loss mechanisms of lithium-ion pouch cells under mechanical indentation conditions

Capacity loss was observed in Li-ion cells after mechanical deformation approaching the onset of internal short circuit (ISCr). In this paper, a series of indentation tests were carried out on commercial Li-ion cells of three capacities (500, 1500 and 2000 mAh). Both in-situ and ex-situ methods were used to investigate the mechanisms of indentation-induced capacity loss. We note after indentation test, the cell capacity reduced by 0.5%–6% of its original value. The incremental capacity (IC) analysis results showed that IC curves generally shifted to lower voltage region, indicating the increase in cell internal resistance. In addition, the fitting results of electrochemical impedance spectroscopy (EIS) indicated that mechanical indentation can result in a reduction in ohmic resistance and the increase in polarization resistance. Scanning electron microscopy (SEM) and X-ray computed tomography (XCT) results showed crushing of graphite, mud cracking of copper current collectors and enlarged pores in separator, which is proposed to be the main reasons for the increase in polarization resistance and permanent capacity loss. The rapid capacity loss due to mechanical abuse was compared with the long-term capacity fading.

25 ENERGY STORAGE↗
DOE OSTI2020

Microstructure reconstruction of battery polymer separators by fusing 2D and 3D image data for transport property analysis

A new approach to generate high-fidelity 3D microstructure reconstructions by leveraging resolution and sample volume characteristics from 2D and 3D microscopy methods is presented here. This approach is employed to model the microstructure of a highly orthotropic polypropylene separator used in lithium-ion batteries, which have challenging multi-scale features of fibrils (<100 nm) and lamellae (>100 nm) to resolve in 3D. Phase contrast nano X-ray computed tomographic data are used to reconstruct the lamellae phase, while 2D scanning electron microscopy data are used to characterize sub-100 nm microstructure features such as the thin fibrils that are beyond the effective resolution of X-ray computed tomography. Fibril geometries are reconstructed stochastically based on the 2D higher resolution data, and integrated with the lamellae geometries in 3D space. Transport property analyses are performed to investigate the bias of microstructure models without considering the fibrils. A sensitivity study is also conducted to facilitate understanding of the relationship between microstructure characteristics and transport properties.

25 ENERGY STORAGE↗
DOE OSTI2021

Development of high-performance roll-to-roll-coated gas-diffusion-electrode-based fuel cells

This study focuses on determining fabrication conditions to create high-performance roll-to-roll-coated (R2R-coated) gas-diffusion electrodes (GDEs) for proton-exchange-membrane fuel cells (PEMFCs). Here, we examine how process conditions influence the distribution of ionomer in the electrode, which is shown to be critical for high performance. Using a combination of Kelvin probe, X-ray photoelectron spectroscopy, and nano-scale X-ray computed tomography we show that formation of an ionomer-rich surface is promoted by using a higher drying rate. We show that R2R-coated GDEs have higher surface ionomer concentration than spray-coated GDEs, which enables these R2R-coated GDEs to not need an additional ionomer overlayer, as is typically the case for spray-coated GDEs. This will reduce the number of processing steps and lower material costs in a manufacturing setting. This work shows that with the appropriate selection of materials, ink formulation, and processing conditions, direct-coated GDEs are a viable pathway for fuel cell manufacturing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Discharge intermittency considerably changes ZnO spatial distribution in porous Zn anodes

Porous Zn anodes are ubiquitous in primary batteries and are under development for low-cost rechargeable batteries. Spatial distribution of ZnO discharge product is a critical factor in these, because it can passivate the active material. In rechargeable cells this is related to a major failure mechanism called shape change, in which ZnO is relocated to inactive locations. In this work we demonstrate rest steps during discharge of primary Zn anodes dramatically alter the placement of ZnO in the anode. In alkaline electrolyte, ZnO discharge product is typically modeled as precipitating close to Zn particles, forming a porous ZnO shell around the Zn core. Further, anodes discharged continuously at low-rate are compared to anodes similarly discharged intermittently, using in situ computed tomography from a synchrotron source. Zn–ZnO core-shell structures are produced during continuous discharge but are not found in cells discharged intermittently. Continuously discharged cells showed that ZnO was formed most strongly near the separator, in agreement with Zn anode battery models. In pulse-discharged cells, ZnO was more radially distributed and was in large formations not physically connected to Zn particles. Thus, discharge intermittency changes spatial distribution of ZnO in ways that are unpredicted by Zn anode models.

25 ENERGY STORAGE↗
DOE OSTI2023

Titanium porous-transport layers for PEM water electrolysis prepared by tape casting

While the porous-transport layer (PTL) is a key component in PEM electrolyzers, it is one of the most underexplored due to limited available structures. In this work, we present a novel PTL design for PEM water electrolyzers enabled by a cost-effective, scalable tape-casting technique. Here, a precise control of the PTL pore structure is achieved by incorporating poreformers of various sizes, and by varying the titanium and poreformer ratio. The structures are characterized with SEM and synchrotron X-ray computed tomography imaging techniques. Comprehensive electrochemical performance analysis demonstrates that higher titanium loading provides improved contact at the catalyst-layer/PTL interface but suffers from severe mass-transport losses due to gas bubbles. We solve this mass-transport problem by mixing in large poreformer beads that produce a highly porous structure with excellent gas removal properties yet still maintaining mechanical integrity. The PTL fabricated with 60:40 Ti:PMMA ratio and 60 μm PMMA bead size outperformed the standard commercial Ti powder-based PTL by 62 mV at 4 A/cm 2 .

25 ENERGY STORAGE↗
DOE OSTI2024

Impact of polymer additives on crack mitigation of rod-coated fuel cell cathode catalyst layers

Cracks in catalyst layers (CLs) are a potential source of long-term failure in a fuel cell membrane electrode assembly (MEA). While modifications to the CL ink formulation can affect the degree of cracking, these changes may lead to lower initial performance than their cracked analogues due to the established link between formulation and performance. In this work, we explored the use of polymeric additives to mitigate CL cracks. Small quantities of poly (acrylic acid), poly (ethylene oxide), poly (methyl methacrylate), or poly (vinyl alcohol) - 5 wt% relative to ionomer mass - were added to the ink prior to its final mixing. Poly (vinyl alcohol) resulted in crack-free CLs, whereas the other polymers resulted in CLs with similar crack percentages as the control CL. Through a combination of transmission electron microscopy, X-ray computed tomography, and infrared spectroscopy, we ascribed the crack-mitigating mechanism of poly (vinyl alcohol) to its ability to hydrogen-bond with Nafion, the ion conducting polymer binder in the catalyst ink. Initial performance of this non-cracked electrode exhibited nearly identical electrochemical behavior to its cracked counterpart, demonstrating that PVA additives successfully reduce cracks while maintaining cell initial performance.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2026

Gas-driven short disconnection mitigates thermal runaway in Li-ion batteries under mechanical abuse

Mechanical abuse poses a critical safety risk to Li-ion batteries by inducing internal short circuits that initiate thermal runaway. Remarkably, voltage recovery frequently emerges during thermal runaway initiation, a phenomenon that conventional theories fail to explain. Here, our study develops a new multiphysics mechanism to explain voltage recovery, termed gas-driven short disconnection, whereby internal gas pressure mechanically disengages short-circuit contacts and causes the cell voltage to rebound. This mechanism incorporates gas generation and its structural impact on the short circuit. Real-time optical and thermal imaging and X-ray computed tomography reveal fluid-structure interaction between internal gas flow and adjacent shorting contacts. We establish a mechanistic framework linking gas-driven short disconnection to cell-level voltage and temperature responses, elucidating the extension–truncation pattern of voltage recovery. Furthermore, thermal regime maps show that a voltage recovery duration exceeding 5 s correlates with limited temperature rise below 150 °C, indicating that sustained short-circuit disconnection suppresses Joule heating. Additionally, a dimensionless criterion is deduced from scaling analysis for physical plausibility of gas-driven short disconnection in mechanically abused cells. This finding inspires smart venting control, which regulates gas release to maintain the internal pressure while dissipating gas enthalpy, thereby providing a device-level strategy for thermal runaway mitigation.

Gas-driven short disconnection↗
DOE OSTI2021

An improved specimen preparation method for marine shallow gas-bearing sand sediments and its validations

Instabilities of shallow gas-charged seabed are potential geological hazards in ocean engineering. In practice, the conventional field sampling techniques failed to obtain undisturbed gas-bearing sediments from the seabed for laboratory mechanical testing because of sensitive gas exsolution and escape from sediments. However, preparation of representative remoulded gas-charged specimens is a challenging issue, because it is rather difficult to quantitatively control the gas content and obtain uniform distribution of gas bubbles within the specimen. Given the above problems, this work proposes a reliable approach to reconstitute the high-saturation specimen of gas-charged sediments in the laboratory by an improved multifunction integrated triaxial apparatus (MITA). This apparatus is developed based on an advanced stress path triaxial system by introducing a temperature-controlled system and a wave-monitoring system. The temperature-controlled system is used to accurately mimic the in situ environments of sediments in the seabed. The wave-monitoring system is utilized to identify exsolution point of free gas and examine the disturbance of gas to specimens during gas exsolution. The detailed procedure of gassy specimen preparation is introduced. Then, the quality of prepared specimens using our improved apparatus is validated by the high-resolution micro-X-ray computed tomography (μCT) scanning test, from which bubble occurrence and size distribution within the gassy sand specimen can be obtained; and preliminary mechanical tests on gassy sand specimens with various initial saturation degrees are performed. The proposed specimen preparation procedure succeeds in proving the postulated occurrence state of gas bubbles in coarse-grained sediments and accurately controlling the gas content.

58 GEOSCIENCES↗
DOE OSTI2022

Critical differences between electron beam melted and selective laser melted Ti-6Al-4 V

Effective optimization of the production of Ti-6Al-4 V using AM requires a fundamental understanding of the relative importance of different microstructural features to the deformation and failure mechanisms, particularly features that vary between production methods. In this study, the tensile response and deformation mechanisms of electron beam melted (EBM) AM Ti-6Al-4 V material loaded in different orientations and produced using various powder sizes were compared to those of selective laser melted (SLM) AM Ti-6Al-4 V material. The density and morphology of pores, phase fractions, prior-β grains, and defect microstructures were evaluated using scanning electron microscopy, X-ray computed tomography, electron backscatter diffraction, and transmission electron microscopy before and after deformation. The results were used to evaluate the relative importance of each feature on strengthening, deformation, and failure initiation mechanisms. Results focused primarily on coarse-powder EBM materials indicated that phase distribution and defect density were most influential for determining material yield strength as well as maximum possible strain to failure. Porosity was lower overall in EBM Ti-6Al-4 V than in SLM, allowing for occasional increases in part strain to failure, but remained a limiting factor determining overall part ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Modeling deformation and failure in AlSi-polyester abradable sealcoating material using microstructure-based finite element simulation

A plasma-sprayed aluminum-silicon (AlSi)/polyester coating is applied in modern gas turbine engines as an abradable sealcoating to maintain tight clearances between the rotating blades and the static casing. While running the engine, the rotating blades “rub” with the abradable coating, which results in extreme strain rate (up to 10 6 ) dynamics and a high-temperature environment. Due to the difficulty of collecting direct measurements, predictive computational models are important for analyzing the deformation and failure of the abradable material, to help meet the design target of avoiding damage to the blade tip and maintaining high fuel efficiency. In this research, a microstructure-based finite element (FE) computational model was developed to capture the complex mechanical behavior of the AlSi/polyester microstructure. The model is based on a virtual representative-volume-element (RVE) of a metal-polymer microstructure, reconstructed from x-ray computed tomography. It models the plastic deformation of, and damage to, each AlSi and polyester constituents, as well as the failure at their interface. The model was calibrated and validated with uniaxial tension and compression experiments, conducted at two temperatures (298 K and 533 K) at an applied strain rate of 10 3 - 10 4 s -1 . The material exhibited strongly asymmetric tension-compression behavior and a sensitivity to temperature, which was well captured by the model. The model was further applied to investigate changes in mechanical behavior due to variations in constituents’ volume fractions, which provides guidance to the microstructural design of AlSi/polyester abradable materials. The model is expected to facilitate the development of improved abradable materials by bypassing the conventional trial-and-error approach and extensive testing requirements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Using porous random fields to predict the elastic modulus of unoxidized and oxidized superfine graphite

Nuclear graphite is a candidate material for Generation IV nuclear power plants. Porous materials such as graphite can contain complex networks of pores that influence the material's mechanical and irradiation response. A methodology known as the random finite element method (RFEM) was adapted to create synthetic microstructures and predict the influence of porosity on the elastic properties of graphite during oxidation. RFEM combines random field theory and the finite element method in a Monte Carlo framework to estimate the mechanical response of a given grade of graphite. In this research, the random fields were verified through experimental characterization to predict the elastic response of three nuclear graphite grades, ETU-10, IG-110, and 2114. Finite element models (FEM) were generated using segmentations of x-ray computed tomography (XCT) data known as image-based models (IBMs) to validate and compare with the RFEM results and better understand the effects of uniform oxidation in these graphite grades. The RFEM predictions appear to correlate well with the experimental values of the measured Young’s modulus of the three graphite grades and display the same trends as IBMs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Multi phenomena melt pool sensor data fusion for enhanced process monitoring of laser powder bed fusion additive manufacturing

Finding actionable trends in laser-based metal additive manufacturing process monitoring data is challenging owing to the diversity and complexity of the underlying physical interactions. A single monitoring solution that captures a particular process phenomenon, such as a photodiode that tracks melt pool intensity, is not alone capable of evaluating process stability or detecting flaw formation with sufficient precision for routine application in industry. In this work, to improve flaw detection performance, we adopted a data fusion approach that captures multiple process phenomena. To demonstrate this, we acquired data from laser powder bed fusion (LPBF) builds of cylindrical specimens produced with different laser spot sizes, emulating defocusing due to process faults such as thermal lensing. The resulting specimens had porosity of varying types and severity, quantified by post-build non-destructive X-ray computed tomography, Archimedes density measurements, and destructive metallographic characterization. During the build, the melt pool state was monitored with two coaxial high-speed video cameras and a temperature field imaging system. Physically intuitive low-level melt pool signatures, such as melt pool temperature, shape and size, and spatter intensity were extracted from this high-dimensional, image-based sensor data. These process signatures were subsequently used as input features in relatively simple machine learning models, such as a support vector machine, which were trained to detect laser defocusing, and in addition, predict porosity type and severity. The results show that the data fusion approach significantly enhanced system performance by reducing the overall false positive rate from ~ 0.1 to ~ 0.001 without sacrificing the true positive rate (~0.90). These results were at par with a black-box, deep machine learning approach (convolutional neural network).

36 MATERIALS SCIENCE↗