Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Colloidal crystals”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Dynamic Atomistic Polar Structure Underpins Ultrahigh Linear Electro-Optic Coefficient in Transparent Ferroelectric Ceramics

Transparent ferroelectrics with high linear electro-optic (EO) coefficients are critical for advanced electro-optical devices. However, achieving optical transparency in ferroelectric ceramics remains challenging due to visible light scattering caused by defects such as domain walls, grain boundaries, and pores. Here, we report the successful fabrication of transparent ferroelectric ceramics through innovative chemical composition design and an advanced two-step sintering process in the La-doped Pb(Mg 1/3 Nb 2/3 )O 3 –PbTiO 3 system. The optical transparency, which is near the theoretical upper limit, can be attributed to the wide band gap and the minimization of light scattering of defects. By minimizing porosity and engineering grain/domain sizes to differ significantly from the wavelengths of visible light, we suppress scattering, achieving optical transparency near the theoretical upper limit. Strikingly, these ceramics exhibit an ultrahigh linear EO coefficient of ∼1417 pm/V, over 65 times greater than that of LiNbO 3 single crystals, the current industry standard. We attribute this exceptional performance to dynamic atomistic polar structures within switchable, thermally stable domains, which enhance electronic polarization sensitivity. This mechanism is corroborated by dielectric spectroscopy, high-resolution transmission electron microscopy and simulation. Our findings offer insights into the design of cost-effective transparent materials with exceptional EO properties, paving the way for next-generation electro-optical devices.

36 MATERIALS SCIENCE↗

A New Method for Polishing Laminated Dissimilar Metals

Here, this paper presents a novel method for preparing metallographic samples of laminated dissimilar metals, specifically a layered structure of zirconium (Zr), vanadium (V), and tungsten (W), which pose a challenge due to their differing crystal structures and hardness levels. The work was motivated by the need to develop a cladding for tungsten targets in spallation neutron sources, where a zirconium face is applied over an interlayer of either vanadium or titanium to prevent the formation of brittle intermetallic compounds such as ZrW 2 . Traditional polishing techniques prove inadequate because each constituent metal requires a different polishing approach based on its unique material properties. The methodology outlined includes a sequential process involving conductive epoxy mounting, successive grinding and polishing with specific abrasives, and a final chemical-mechanical polish using a colloidal silica-based solution. Optical microscopy confirmed that this multi-step process successfully produced scratch-free surfaces and minimized surface relief across the different metal interfaces. Although developed for refractory metals, this approach shows promise for other layered structures comprised of transition metals, offering a meticulous yet effective technique for high-quality metallographic sample preparation.

Newberry, Daniel [Oak Ridge National Laboratory (O↗

Pair Distribution Function Analysis of ZrO2 Nanocrystals and Insights in the Formation of ZrO2-YBa2Cu3O7 Nanocomposites

The formation of superconducting nanocomposites from preformed nanocrystals is still not well understood. Here, we examine the case of ZrO2 nanocrystals in a YBa2Cu3O7-x matrix. First we analyzed the preformed ZrO2 nanocrystals via atomic pair distribution function analysis and found that the nanocrystals have a distorted tetragonal crystal structure. Second, we investigated the influence of various surface ligands attached to the ZrO2 nanocrystals on the distribution of metal ions in the pyrolyzed matrix via secondary ion mass spectroscopy technique. The choice of stabilizing ligand is crucial in order to obtain good superconducting nanocomposite films with vortex pinning. Short, carboxylate based ligands lead to poor superconducting properties due to the inhomogeneity of metal content in the pyrolyzed matrix. Counter-intuitively, a phosphonate ligand with long chains does not disturb the growth of YBa2Cu3O7-x. Even more surprisingly, bisphosphonate polymeric ligands provide good colloidal stability in solution but do not prevent coagulation in the final film, resulting in poor pinning. These results thus shed light on the various stages of the superconducting nanocomposite formation.

YBa2Cu3O7−δ↗

Refractive Index and Abbe Number Tuning via 3D Printable Optical Quality Silica–Titania–Germania Glasses

The development of optical quality GeO 2 –TiO 2 –SiO 2 glasses compatible with direct ink writing (DIW) 3D printing is reported in this study. Colloidal GeO 2 and TiO 2 –SiO 2 core–shell feedstocks are prepared by a sol–gel method and converted to printable inks for DIW. Printed inks are subsequently densified to glass using heat treatment at temperatures up to 1100 °C in air. A series of print‐compatible glass compositions are prepared, yielding transparent glass with the highest refractive index n = 1.576. Herein, it is shown that more TiO 2 can be incorporated into the glass without haziness or scattering through the addition of GeO 2 . The mechanisms for this are discussed, and it is shown that crystallization persists in these glasses despite the lack of visible light scattering. Finally, the combination of both TiO 2 and GeO 2 into a ternary glass also is used to independently tune the dispersion properties of the glass, as demonstrated by measured refractive indices and Abbe numbers, which has potential implications for 3D‐printed optics.

36 MATERIALS SCIENCE↗

Synthesis of nanocrystalline CeO{sub 2} particles by different emulsion methods

Cerium oxide nanoparticles were synthesized using three different methods of emulsion: (1) reversed micelle (RM); (2) emulsion liquid membrane (ELM); and (3) colloidal emulsion aphrons (CEAs). Ammonium cerium nitrate and polyoxyethylene-4-lauryl ether (PE4LE) were used as cerium and surfactant sources in this study. The powder was calcined at 500 Degree-Sign C to obtain CeO{sub 2}. The effect of the preparation procedure on the particle size, surface area, and the morphology of the prepared powders were investigated. The obtained powders are highly crystalline, and nearly spherical in shape. The average particle size and the specific surface area of the powders from the three methods were in the range of 4-10 nm and 5.32-145.73 m{sup 2}/g, respectively. The CeO{sub 2} powders synthesized by the CEAs are the smallest average particle size, and the highest surface area. Finally, the CeO{sub 2} prepared by the CEAs using different cerium sources and surfactant types were studied. It was found that the surface tensions of cerium solution and the type of surfactant affect the particle size of CeO{sub 2}. - Graphical Abstract: The emulsion droplet size distribution and the TEM images of CeO{sub 2} prepared by different methods: reversed micelle (RM), emulsion liquid membrane (ELM) and colloidal emulsion aphrons (CEAs). Highlights: Black-Right-Pointing-Pointer Nano-sized CeO{sub 2} was successfully prepared by three different emulsion methods. Black-Right-Pointing-Pointer The colloidal emulsion aphrons method producing CeO{sub 2} with the highest surface area. Black-Right-Pointing-Pointer The surface tensions of a cerium solution have slightly effect on the particle size. Black-Right-Pointing-Pointer The size control could be interpreted in terms of the adsorption of the surfactant.

36 MATERIALS SCIENCE↗

Electrochemical synthesis and characterization of stable colloidal suspension of graphene using two-electrode cell system

The present work reports the synthesis and characterization of graphene via electrochemical exfoliation of graphite rod using two-electrode system assisted by Sodium Dodecyl Sulphate (SDS) as a surfactant. The electrochemical process was carried out with sequence of intercalation of SDS onto the graphite anode followed by exfoliation of the SDS-intercalated graphite electrode when the anode was treated as cathode. The effect of intercalation potential from 5 V to 9 V and concentration of the SDS surfactant of 0.1 M and 0.01 M were investigated. UV-vis Spectroscopic analysis indicated an increase in the graphene production with higher intercalation potential. Transmission Electron Microscopy (TEM) analysis showed a well-ordered hexagonal lattice of graphene image and indicated an angle of 60° between two zigzag directions within the honeycomb crystal lattice. Raman spectroscopy analysis shows the graphitic information effects after the exfoliation process.

36 MATERIALS SCIENCE↗

Exciton-Exciton Annihilation in Copper-Phthalocyanine Single-Crystal Nanowires

Femtosecond one-color pump-probe spectroscopy was applied to study exciton dynamics in single-crystal copper-phthalocyanine (CuPc) nanowires grown on an opaque silicon substrate. The transient reflectance kinetics measured at different pump fluences exhibit a remarkable intensity-dependent decay behavior which accelerates significantly with increasing pump pulse intensity. All the kinetic decays can be satisfactorily described using a bi-exponential decay function with lifetimes of 22 and 204 ps, and corresponding relative amplitudes depending on the pump intensity. The accelerated decay behavior observed at high pump intensities arises from a nonlinear exciton-exciton annihilation process. While this phenomenon has been found previously in crystalline metallophthalocyanine (MPc) polymorphs such as colloidal particles and thin films, the results obtained using the CuPc nanowires are markedly distinct, namely, much longer decay times and a linear intensity dependence of the initial peak amplitudes. Despite these differences, detailed data analysis further shows that, as found for other metal-phthalocyanine polymorphs, exciton-exciton annihilation in the CuPc nanowires is one-dimensional (1D) diffusion-limited, which possibly involves intra-chain exciton diffusion along 1D molecular stacks. The significantly long-lived excitons of CuPc nanowires in comparison to those of other crystalline polymorphs make them particularly suitable for photovoltaic applications.

Ma, Yingzhong↗

Mechanism of shape symmetry breaking in surfactant-mediated crystal growth

We present a dynamical model of crystal growth, in which it is possible to reliably achieve asymmetric products, beginning from symmetric initial conditions and growing within an isotropic environment. The asymmetric growth is the result of a positive feedback mechanism that amplifies the effect of thermal fluctuations in the coverage of surfactants on the growing crystalline facets. Within our simple model, we are able to understand the kinetic and thermodynamic factors involved in both the onset of symmetry breaking and the persistence of anisotropic growth. We demonstrate that the mechanism is general by studying models with increasing complexity. We argue that this mechanism of symmetry breaking underpins observations of colloidal, seed-mediated syntheses of single crystalline metal nanorods capped with strongly interacting surfactants. The parameters within our model are related to experimental observables such as the concentration, hydrophobicity, and binding strength of the surfactants, which suggests a potential route to optimize the yield of asymmetric products in colloidal nanoparticle syntheses.

Oaks-Leaf, Sam↗

Solvothermal hot injection synthesis of core-shell AgNi nanoparticles

Silver-nickel core-shell nanoparticles (NP) were prepared by solvothermal hot injection synthesis by simultaneous thermolysis/reduction of AgNO 3 and Ni(acac) 2 precursors in the hot mixture of octadecene and oleylamine. Oleylamine decreases decomposition temperature of AgNO 3 to that of Ni(acac) 2 thus ensuring favorable reaction conditions. The prepared AgNi NPs with different Ag/Ni ratios were completely characterized. Dynamic light scattering (DLS) and small angle X-ray scattering (SAXS) were used for particle size characterization of as-prepared AgNi colloids. There is no dependence of the particle size (13–21 nm by SAXS) on the Ag/Ni stoichiometric ratio, but the ultraviolet–visible spectroscopy (UV–vis) reveals that the intensity of the surface plasmon (SPR) decreases with increasing Ni content. Transmission electron microscopy (TEM) verified the results of DLS and SAXS and showed spherical nanoparticle shape. Distribution of individual elements in the nanoparticles was mapped by high resolution scanning transmission electron microscopy and energy dispersive X-ray spectroscopy (STEM-EDS) and revealed their core-shell structure where an Ag nucleus is covered by a thin amorphous Ni layer. Upon heating to 400 °C, Ni crystallization is substantiated by appearance of diffractions in the high-temperature X-ray powder diffractograms (HT-XRD) and of a magnetic moment. Ultimate phase separation was proven by scanning electron microscopy and energy dispersive X-ray analysis (SEM-EDS) in samples heated to 1000 °C. The reaction course and nanoparticle formation studied by DLS, UV–vis, and Ag and Ni elemental analyses reveal an initial Ag seed formation with subsequent Ni overlayer deposition after 180 s.

36 MATERIALS SCIENCE↗

Skyrmion-skyrmionium phase separation and laning transitions via spin-orbit torque currents

Many driven binary systems can exhibit laning transitions when the two species have different mobilities, such as colloidal particles with opposite charges in electric fields. Another example is pedestrian or active-matter systems, where particles moving in opposite directions form a phase-separated state that enhances the overall mobility. In this work, we use atomistic simulations to demonstrate that mixtures of skyrmions and skyrmioniums also exhibit pattern formation and laning transitions. Skyrmions move more slowly and at a finite skyrmion Hall angle compared to skyrmioniums, which move faster and without a skyrmion Hall effect. At low drives, the system forms a partially jammed phase where the skyrmioniums are dragged by the surrounding skyrmions, resulting in a finite angle of motion for the skyrmioniums. At higher drives, the system transitions into a laned state, but unlike colloidal systems, the lanes in the skyrmion-skyrmionium mixture are tilted relative to the driving direction due to the intrinsic skyrmion Hall angle. In the laned state, the skyrmionium angle of motion is reversed when it aligns with the tilted lane structure. At even higher drives, the skyrmioniums collapse into skyrmions. Below a critical skyrmion density, both textures can move independently with few collisions, but above this density, the laning state disappears entirely, and the system transitions to a skyrmion-only state. We map out the velocity and Hall responses of the different textures and identify three distinct phases: partially jammed, laned, and skyrmion-only moving crystal states. In conclusion, we compare our results to recent observations of tilted laning phases in pedestrian flows, where chiral symmetry breaking in the particle interactions leads to similar behavior.

36 MATERIALS SCIENCE↗

Switchable geometric frustration in an artificial-spin-ice–superconductor heterosystem

Geometric frustration emerges when local interaction energies in an ordered lattice structure cannot be simultaneously minimized, resulting in a large number of degenerate states. The numerous degenerate configurations may lead to practical applications in microelectronics(1), such as data storage, memory and logic(2). However, it is difficult to achieve very high degeneracy, especially in a two-dimensional system(3,4). Here, we showcase in situ controllable geometric frustration with high degeneracy in a two-dimensional flux-quantum system. We create this in a superconducting thin film placed underneath a reconfigurable artificial-spin-ice structure(5). The tunable magnetic charges in the artificial-spin-ice strongly interact with the flux quanta in the superconductor, enabling switching between frustrated and crystallized flux quanta states. The different states have measurable effects on the superconducting critical current profile, which can be reconfigured by precise selection of the spin-ice magnetic state through the application of an external magnetic field. We demonstrate the applicability of these effects by realizing a reprogrammable flux quanta diode. The tailoring of the energy landscape of interacting 'particles' using artificial-spin-ices provides a new paradigm for the design of geometric frustration, which could illuminate a path to control new functionalities in other material systems, such as magnetic skyrmions(6), electrons and holes in two-dimensional materials(7,8), and topological insulators(9), as well as colloids in soft materials(10-13).

Wang, Yong-Lei (ORCID:0000000303917757)↗

Insights Into the Mineralogy and Surface Chemistry of Extracellular Biogenic S 0 Globules Produced by Chlorobaculum tepidum

Elemental sulfur (S 0 ) is produced and degraded by phylogenetically diverse groups of microorganisms. For Chlorobaculum tepidum , an anoxygenic phototroph, sulfide is oxidized to produce extracellular S 0 globules, which can be further oxidized to sulfate. While some sulfur-oxidizing bacteria (e.g., Allochromatium vinosum ) are also capable of growth on commercial S 0 as an electron donor, C. tepidum is not. Even colloidal sulfur sols, which appear indistinguishable from biogenic globules, do not support the growth of C. tepidum . Here, we investigate the properties that make biogenic S 0 globules distinct from abiotic forms of S 0 . We found that S 0 globules produced by C. tepidum and abiotic S 0 sols are quite similar in terms of mineralogy and material properties, but the two are distinguished primarily by the properties of their surfaces. C. tepidum ’s globules are enveloped by a layer of organics (protein and polysaccharides), which results in a surface that is fundamentally different from that of abiotic S 0 sols. The organic coating on the globules appears to slow the aging and crystallization of amorphous sulfur, perhaps providing an extended window of time for microbes in the environment to access the more labile forms of sulfur as needed. Overall, our results suggest that the surface of biogenic S 0 globules may be key to cell–sulfur interactions and the reactivity of biogenic S 0 in the environment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Effects of Ground and Space Processing on the Properties of Organic, Polymeric, and Colloidal Materials

In recent years, a great deal of interest has been directed toward the use of organic materials in the development of high-efficiency optoelectronic and phototonic devices. There is a myriad of possibilities among organic materials which allow flexibility in the design of unique structures with a variety of functional groups. The use of nonlinear optical (NLO) organic materials as thin film wave-guides allows full exploitation of their desirable qualifies by permitting long interaction lengths and large susceptibilities allowing modest power input. There are several methods in use to prepare thin films such as Langmuir-Blodgett (LB) and self-assembly techniques, vapor deposition, growth from sheared solution or melt, and melt growth between glass plates. Organic-based materials have many features that make them desirable for use in optical devices, such as high second-and third-order nonlinearity, flexibility of molecular design, and damage resistance to optical radiation. However, their use in devices has been hindered by processing difficulties for crystals and thin films. We discuss the potential role of microgravity processing of a few organic and polymeric materials. It is of interest to note how materials with second-and third-order NLO behavior may be improved in a diffusion-limited environment and ways in which convection may be detrimental to these materials. We focus our discussion on third-order materials for all-optical switching, and second-order materials for frequency conversion and electrooptics. The goal of minimizing optical loss obviously depends on processing methods. For solution-based processes, such as solution crystal growth and solution photopolymerization, it is well known that thermal and solutal density gradients can initiate buoyancy-driven convection. Resultant fluid flows can affect transport of material to and from growth interfaces and become manifest in the morphology and homogeneity of the growing film or crystal. Likewise, buoyancy-driven convection can hinder production of defect-free, high-quality crystals or films during crystal and film growth by vapor deposition.

Frazier, Donald O.↗

Ordered Nanostructured Amphiphile Self-Assembly Materials from Endogenous Nonionic Unsaturated Monoethanolamide Lipids in Water

The self-assembly, solid state and lyotropic liquid crystalline phase behavior of a series of endogenous n-acylethanolamides (NAEs) with differing degrees of unsaturation, viz., oleoyl monoethanolamide, linoleoyl monoethanolamide, and linolenoyl monoethanolamide, have been examined. The studied molecules are known to possess inherent biological function. Both the monoethanolamide headgroup and the unsaturated hydrophobe are found to be important in dictating the self-assembly behavior of these molecules. In addition, all three molecules form lyotropic liquid crystalline phases in water, including the inverse bicontinuous cubic diamond (Q{sub II}{sup D}) and gyroid (Q{sub II}{sup G}) phases. The ability of the NAE's to form inverse cubic phases and to be dispersed into ordered nanostructured colloidal particles, cubosomes, in excess water, combined with their endogenous nature and natural medicinal properties, makes this new class of soft mesoporous amphiphile self-assembly materials suitable candidates for investigation in a variety of advanced multifunctional applications, including encapsulation and controlled release of therapeutic agents and incorporation of medical imaging agents.

59 BASIC BIOLOGICAL SCIENCES↗

Aluminosilicate colloidal gels: from the early age to the precipitation of zeolites

Aluminosilicate hydrogels are often considered to be precursors for the crystallisation of zeolites carried out under hydrothermal conditions. The preparation of mechanically homogeneous aluminosilicate gels enables the study of these materials through bulk rheology and observation of the aging dynamics until the precipitation of crystalline zeolites. The first part of this study deals with the establishment of ternary state diagrams, in order to identify the range of chemical formulations that enable preparation of single-phase homogeneous gels. Then, by studying the viscoelastic moduli during the gelation reaction, and by yielding the gel under large deformation, we propose an empirical law considering the partial order of reaction on each chemical element, to predict the gelation time according to the chemical formulation. The scaling behavior of the elastic properties of this colloidal gel shows a transition from a strong link behavior to a weak link regime. Long term aging results in the shrinkage of the gel, accompanied by syneresis of interstitial liquid at the surface. Zeolites precipitate through crystallisation by a particle attachment mechanism, when thermodynamic equilibrium is reached. The stoichiometry of the precipitated zeolites is not only consistent with the concentration of the remaining species in the supernatant but, surprisingly, it is also very close to the partial order of the reaction of the chemical elements involved in the determination of the critical gel point. This indicates a strong correlation between the morphology of the soft amorphous gel network that is formed at an early age and those of the final solid precipitated crystals.

36 MATERIALS SCIENCE↗

Stability Enhancement of Polymeric Sensing Films Using Fillers

Experiments have shown the stability enhancement of polymeric sensing films on mixing the polymer with colloidal filler particles (submicron-sized) of carbon black, silver, titanium dioxide, and fumed silicon dioxide. The polymer films are candidates for potential use as sensing media in micro/nano chemical sensor devices. The need for stability enhancement of polymer sensing films arises because such films have been found to exhibit unpredictable changes in sensing activity over time, which could result in a possible failure of the sensor device. The changes in the physical properties of a polymer sensing film caused by the sorption of a target molecule can be measured by any of several established transduction techniques: electrochemical, optical, calorimetric, or piezoelectric, for example. The transduction technique used in the current polymer stability experiments is based on piezoelectric principles using a quartz-crystal microbalance (QCM). The surface of the QCM is coated with the polymer, and the mass uptake by the polymer film causes a change in the oscillating frequency of the quartz crystal. The polymer used for the current study is ethyl cellulose. The polymer/ polymer composite solutions were prepared in 1,3 dioxolane solvent. The filler concentration was fixed at 10 weight percent for the composites. The polymer or polymer composite solutions were cast on the quartz crystal having a fundamental frequency of about 6 MHz. The coated crystal was subjected to a multistage drying process to remove all measurable traces of the solvent. In each experiment, the frequency of oscillation was measured while the QCM was exposed to clean, dry, flowing air for about 30 minutes, then to air containing a known concentration of isopropanol for about 30 minutes, then again to clean dry air for about 30 minutes, and so forth. This cycle of measurements for varying isopropanol concentrations was repeated at intervals for several months. The figure depicts some of the sensing film stability results for ethyl cellulose polymer, ethyl cellulose-carbon black, and ethyl cellulose-silicon dioxide composite systems. An ethyl cellulose film exhibited a marked decline in response in the first few months of study and settled to a steady average response after about four months. However, response varied widely around the average response for ethyl cellulose film. In contrast, ethyl cellulose- carbon black and ethyl cellulose-silicon dioxide composites also declined in the early months, but showed more repeatable sensing film activity after the initial decline. Similar trends were observed in experiments for ethyl cellulose-titanium dioxide and ethyl cellulose-silver composites.

Lin, Brian↗

Fabricating Single Crystal Quantum Dot Solids

The central goal of this research program was to establish fundamental synthesis and processing principles to enable the fabrication of single crystal quantum dot solids (QDS) with programmable structure (i.e., hexagonal and square) and composition. Our approach towards that goal leveraged access to and experience with unique in-situ, multi-probe characterization techniques to understand and ultimately control the fundamental relationship between processing conditions and nucleation and growth of QDS. The program integrated synthesis and fabrication (Hanrath) with in-situ TEM analysis (Kourkoutis) and computational modeling (Clancy) to gain atomic-level insights into the underlying physical phenomena governing assembly and attachment and to guide the development of optimized processing methods. We have established a foundational understanding of physicochemical interactions of self-assembly at a fluid interface, superlattice structure transformation pathways, the critical role of disorder during the initial dimerization of colloidal quantum dot monomers, and the residual strain distribution within the inter-dot epitaxial bridge which hampers the formation of novel electronics states of the quantum dot solids. Collectively, these insights have contributed towards advancing the mechanistic understanding of the complex choreography of assembly and attachment as well as understanding what currently limits further advances in high-fidelity quantum dot solids and tiles.

36 MATERIALS SCIENCE↗