SEARCH · Engineering Papers

Results for “Camber”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Challenges in modeling the X-29A flight test performance

The paper presents the methods, instrumentation, and difficulties associated with drag measurement of the X-29A aircraft. The initial performance objective of the X-29A program emphasized drag polar shapes rather than absolute drag levels. Priorities during the flight envelope expansion restricted the evaluation of aircraft performance. Changes in aircraft configuration, uncertainties in angle-of-attack calibration, and limitations in instrumentation complicated the analysis. Limited engine instrumentation with uncertainties in overall in-flight thrust accuracy made it difficult to obtain reliable values of coefficient of parasite drag. The aircraft was incapable of tracking the automatic camber control trim schedule for optimum wing flaperon deflection during typical dynamic performance maneuvers; this has also complicated the drag polar shape modeling. The X-29A was far enough off the schedule that the developed trim drag correction procedure has proven inadequate. Despite these obstacles, good drag polar shapes have been developed throughout the flight envelope. Preliminary flight results have compared well with wind tunnel predictions. A more comprehensive analysis must be done to complete the performance models. The detailed flight performance program with a calibrated engine will benefit from the experience gained during this preliminary performance phase.

Hicks, John W.↗

NASA NTRS1987

Flow energizer flight tests on a light twin aircraft

Experiments were conducted to explore the use of flow energizers (i.e., horizontally mounted vortex generators), using a special instrumentation subsystem installed on a light twin aircraft. The data, collected for energizer configurations with convergence ratios of 1.2, 1.5, and 1.7, included measurements of pressure on the wing surface, velocity components in the wake of the energizer, and forces on the flow energizer itself. Surface pressure data showed that flow energizer effects are highly localized. The energizer with the smallest convergence ratio tested produced an energizer lift/drag ratio about 75 percent lower that that of the other two configurations. For highly swept planforms, cambered energizers with overlaps of the order of 12-15 percent of the local chord provide the best results.

Ward, D. T.↗

NASA NTRS1987

Experimental flowfield visualization of a high alpha wing at Mach 1.62

Experimental oil-flow and tuft patterns and vapor-screen flow-visualization data were obtained on a cambered wing model at Mach 1.62 for an angle-of-attack range of 0 to 14 deg. These data were used as flow diagnostic tools along with surface-pressure and force data and full-potential theory calculations. A large separation bubble was found on the lower wing surface at low angle of attack. The high-angle-of-attack flowfield was characterized by a large attached-flow leading-edge expansion followed by a cross-flow shock. At 14 deg, the cross-flow shock apparently induced discrete regions of streamwise separated flow which were clearly indicated in the vapor-screen and oil-flow photographs.

Pittman, James L.↗

NASA NTRS1987

Experimental flowfield visualization of a high alpha wing at Mach 1.62

Experimental oil-flow and tuft patterns and vapor-screen flow-visualization data were obtained on a cambered wing model at Mach = 1.62 for an angle-of attack range of 0-14 deg. These data were used as flow diagnostic tools along with surface-pressure and force data and full-potential theory calculations. A large separation bubble was found on the lower wing surface at low angle of attack. The high-angle-of-attack flowfield was characterized by a large attached-flow leading-edge expansion followed by a crossflow shock. At alpha = 14 deg the crossflow shock apparently induced discrete regions of streamwise separated flow, which were clearly indicated in the vapor-screen and oil-flow photographs.

Pittman, James L.↗

NASA NTRS1987

Composite grid and finite-volume LU implicit scheme for turbine flow analysis

A composite grid was generated in an attempt to improve grid quality for a typical turbine blade with large camber in terms of mesh control, smoothness, and orthogonality. This composite grid consists of the C grid (or O grid) in the immediate vicinity of the blade and the H grid in the upstream region and in the middle of the blade passage between the C grids. It provides a good boundary layer resolution around the leading edge region for viscous calculation, has orthogonality at the blade surface and slope continuity at the C-H (or O-H) interface, and has flexibility in controlling the mesh distribution in the upstream region without using excessive grid points. This composite grid eliminates the undesirable qualities of a single grid when generated for a typical turbine geometry. A finite-volume lower-upper (LU) implicit schemes can be used in solving for the turbine flows on the composite grid. This grid has a special grid node that is connected to more than four neighboring nodes in two dimensions and to more than six nodes in three dimensions. But the finite-volume approach poses no problem at the special point because each interior cell has only four neighboring cells in two dimensions and only six cells in three dimensions. The finite-volume LU implicit scheme was demonstrated to be robust and efficient for both external and internal flows in a broad flow regime.

Choo, Yung K.↗

NASA NTRS1986

Flight testing the X-29

A testing status report is presented for the X-29 forward-swept-wing experimental aircraft, which integrates such advanced technologies as an aeroelastically tailored composite wing, a thin supercritical airfoil, three-surface pitch control, discrete variable camber, full-authority close-coupled canards, static instability, and digital fly-by-wire flight controls. X-29 flight test results to date raise several issues pertinent to the design of future combat aircraft flight control systems; for example, they bring into question the current MIL-8785C requirements on control system time delays.

Smith, Rogers E.↗

NASA NTRS1987

A strake design method for supersonic speeds and low lift

A method is presented for the design of a strake for a forebody typical of supersonic aircraft at typical cruise (low lift) conditions, in order to ensure attached flow on the strake upper surface. The method systematically varies strake camber and thickness until an attached flow surface pressure distribution is achieved. Surface pressures are computed by the full potential flow solver, NCOREL. The high-alpha flowfield of the strake is also investigated experimentally and computationally; a large vortex is noted on the strake leeside, together with a pair of vortices on the forebody upper centerline. The effect of sideslip on the high-alpha flowfield is also discussed.

Pittman, James L.↗

NASA NTRS1987

Effect of a round airfoil nose on leading-edge suction

Kulfan (1979) assumed that the angle of attack for initial vortex separation on a slender wing with rounded leading edges could be obtained by equating the leading-edge suction (LES) and nose drag coefficients. In the present study, this assumption is examined and is shown to predict reasonably well the initial angle of attack at which laminar separation occurs near the airfoil nose. However, the assumption is shown to be slightly less accurate for thick or cambered airfoils. Attainable LES estimated by Kulfan's method seemed to agree well with that obtained from an airfoil aerodynamics code and experimental data on a NACA 64A009 airfoil at M = 0.4 and Re = 0.86 x 10 to the 6th.

Lan, C. Edward↗

NASA NTRS1988

The development of CFD methods for rotor applications

The optimum design of the advancing helicopter rotor for high-speed forward flight always involves a tradeoff between transonic and stall limitations. However, the preoccupation of the rotor industry was primarily concerned with stall until well into the 1970s. This emphasis on stall resulted from the prevalent use of low-solidity rotors with rather outdated airfoil sections. The use of cambered airfoil sections and higher-solidity rotors substantially reduced stall and revealed the advancing transonic flow to be a more persistent limitation to high-speed rotor performance. Work in this area was spurred not only by operational necessity but also by the development of a tool for the prediction of these flows (the method of computational fluid dynamics). The development of computational fluid dynamics for these rotor problems was a major Army and NASA achievement. This work is now being extended to other rotor flow problems. The developments are outlined.

Caradonna, F. X.↗

NASA NTRS1987

Wind tunnel studies of circulation control elliptical airfoils

Effects of blown jets on the lift and drag of cambered elliptical airfoils are described. Performance changes due to a splitter plate attached to the lower surface of an elliptical airfoil near the trailing edge with and without blowing are indicated. Lift and drag characteristics of airfoils with two blown jets are compared with airfoils with single blowing jets. Airfoil designs that vary the location of a second jet relative to a fixed jet are described.

Franke, M. E.↗

NASA NTRS1988

Problems in fluid dynamics

A scheme was developed for the parametric differentiation and integration of gas dynamics equations. A numerical integration of the gas dynamics equations is necessarily performed for a specific set of parameter values. The linear variational equations are obtained by differentiating the exact equations with respect to each of the relevant parameters. The resulting matrix of flow quantities is referred to as the Jacobi matrix. The subsequent procedure is then straightforward. The method was tested for two dimensional supersonic flow past an airfoil, with airfoil thickness, camber, and angle of attack varied. This approach has great potential value for rapidly assessing the effect of design changes. The other focus of the work was on problems in fluid stability, bifurcations, and turbulence.

Sirovich, Lawrence↗

NASA NTRS1986

High-flaps for natural laminar flow airfoils

A review of the NACA and NASA low-drag airfoil research is presented with particular emphasis given to the development of mechanical high-lift flap systems and their application to general aviation aircraft. These flap systems include split, plain, single-slotted, and double-slotted trailing-edge flaps plus slat and Krueger leading-edge devices. The recently developed continuous variable-camber high-lift mechanism is also described. The state-of-the-art of theoretical methods for the design and analysis of multi-component airfoils in two-dimensional subsonic flow is discussed, and a detailed description of the Langley MCARF (Multi-Component Airfoil Analysis Program) computer code is presented. The results of a recent effort to design a single- and double-slotted flap system for the NASA high speed natural laminar flow (HSNLF) (1)-0213 airfoil using the MCARF code are presented to demonstrate the capabilities and limitations of the code.

Morgan, Harry L.↗

NASA NTRS1987

Pressure field due to drag reducing outer layer devices in turbulent boundary layers

The wall static pressure in the vicinity of drag reducing outer layer devices in flat wall turbulent boundary layers has been measured and compared with an inviscid theory. Symmetric and cambered airfoil devices have been examined at small angles of attack and very low chord Reynolds numbers. Airfoil devices impose a sequence of strong favorable and adverse pressure gradients on the boundary layer whose drag is to be reduced. At very small angles of attack (+ or - 2 deg), this pressure field extends up to about three chord lengths downstream of the trailing edge of an airfoil device. Also examined are the pressures on the upper and lower surfaces of a symmetric airfoil device in the freestream and near the wall. The freestream pressure distribution around an airfoil section is altered by the wall proximity. The relevance of lift enhancement caused by wall proximity to drag reduction has been discussed. The pressure distributions on the flat wall beneath the symmetric airfoil devices are predicted well by the inviscid theory. However, the remaining pressure distributions are predicted only qualitatively, presumably because of strong viscous effects.

Bandyopadhyay, P. R.↗

NASA NTRS1987

X-29A flight control system performance during flight test

An account is given of flight control system performance results for the X-29A forward-swept wing 'Advanced Technology Demonstrator' fighter aircraft, with attention to its software and hardware components' achievement of the requisite levels of system stability and desirable aircraft handling qualities. The Automatic Camber Control Logic is found to be well integrated with the stability loop of the aircraft. A number of flight test support software programs developed by NASA facilitated monitoring of the X-29A's stability in real time, and allowed the test team to clear the envelope with confidence.

Chin, J.↗

NASA NTRS1988

Highlights of experience with a flexible walled test section in the NASA Langley 0.3-meter transonic cryogenic tunnel

The unique combination of adaptive wall technology with a continuous flow cryogenic wind tunnel is described. This powerful combination allows wind tunnel users to carry out two-dimensional (2-D) tests at flight Reynolds numbers with wall interferences essentially eliminated. Validation testing was conducted to support this claim using well tested symmetrical and cambered airfoils at transonic speeds and high Reynolds numbers. The test section hardware has four solid walls, with the floor and ceiling flexible. The method of adapting/shaping the floor and ceiling to eliminate top and bottom wall interference at its source is outlined. Data comparisons for different size models tested and others in several sophisticated 2-D wind tunnels are made. In addition, the effects of Reynolds number, testing at high lift with associated large flexible wall movements, the uniqueness of the adapted wall shapes, and the effects of sidewall boundary layer control are examined. The 0.3-m TCT is now the most advanced 2-D research facility anywhere.

Wolf, Stephen W. D.↗

NASA NTRS1987

LDA measurement of the passage flow field in an annular airfoil cascade

Models to predict the complex three-dimensional flow through turbomachine blade rows are being developed. To verify these models and direct necessary refinements, it is necessary that predictions be correlated with data obtained in experiments which model the fundamental three-dimensional blade row flow phenomena. This paper describes a series of experiments performed in a large scale, subsonic, annular cascade facility specifically designed to provide such data. In particular, the effect of incidence angle on the three-dimensional passage flow field through an annular cascade of cambered airfoils is investigated and quantified, accomplished by obtaining detailed and expensive LDA data. These data demonstrate and quantify the development of the passage vortices through the airfoil passage and their strong interaction with the endwall boundary layers.

Stauter, R. C.↗

NASA NTRS1988

The effects of compressibility on dynamic stall

In this paper, typical computational predictions and experimental measurements of compressible flow past an airfoil at dynamic stall conditions are studied and compared to develop an insight into the effect of compressibility on dynamic stall. The dependency of the critical Mach number on airfoil leading edge curvature, camber, and angle of attack is investigated. Evidence is presented to show that a local region of supersonic flow occurs on an oscillating airfoil, even for a freestream Mach number as low as 0.2, if the boundary layer remains attached and the angle of attack is sufficiently high; that a shock terminates this local supersonic bubble; and that the vorticity that this shock generates grows rapidly and becomes very unstable as the angle of attack increases beyond the value at which the maximum local flow speed first exceeds the speed of sound. It is suggested that these shock-induced effects compete with the dynamic viscous effects occurring in the boundary layer in determining the onset of separation, which can lead to premature dynamic stall and can significantly reduce the maximum dynamic lift that can otherwise be obtained.

Fung, K.-Y.↗

NASA NTRS1988

Highlights of experience with a flexible walled test section in the NASA Langley 0.3-meter transonic cryogenic tunnel

The unique combination of adaptive wall technology with a contonuous flow cryogenic wind tunnel is described. This powerful combination allows wind tunnel users to carry out 2-D tests at flight Reynolds numbers with wall interference essentially eliminated. Validation testing was conducted to support this claim using well tested symmetrical and cambered airfoils at transonic speeds and high Reynolds numbers. The test section hardware has four solid walls, with the floor and ceiling flexible. The method of adapting/shaping the floor and ceiling to eliminate top and bottom wall interference at its source is outlined. Data comparisons for different size models tested and others in several sophisticated 2-D wind tunnels are made. In addition, the effects of Reynolds number, testing at high lift with associated large flexible wall movements, the uniqueness of the adapted wall shapes, and the effects of sidewall boundary layer control are examined. The 0.3-m TCT is now the most advanced 2-D research facility anywhere.

Wolf, Stephen W. D.↗