Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CONFIGURABLE APPLICATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Modulur DIPS, 2.5-kWe modules for lunar/Mars surface applications, design point selection summary

The results are presented of a systematic series of studies leading to the selection and conceptual design development of a Dynamic Isotope Power System (DIPS) module for lunar and Martian surface applications. An optimum system configuration has been developed for the module that provides a system with a radiator area which is small and manageable without significantly impacting the system mass, efficiency, and technological risk. The maximum design temperature for the system has been determined.

Otting, William D.↗

A method of predicting quasi-steady aerodynamics for flutter analysis of high speed vehicles using steady CFD calculations

High speed linear aerodynamic theories like piston theory and Newtonian impact theory are relatively inexpensive to use for flutter analysis. These theories have limited areas of applicability depending on the configuration and the flow conditions. In addition, these theories lack the ability to capture viscous, shock and real gas effects. CFD methods can model all of these effects accurately, but the unsteady calculations required for flutter are expensive and often impractical. This paper describes a method for using steady CFD calculations to approximate the generalized aerodynamic forces for a flutter analysis. Example two-and three-dimensional aerodynamic force calculations are provided. In addition, a flutter analysis of a NASP-type wing will be discussed.

Scott, Robert C.↗

Near-field supersonic flow predictions by an adaptive unstructured tetrahedral grid solver

Applicability of a three-dimensional solution adaptive unstructured tetrahedral Euler flow solver about generic models for near-field sonic boom pressure signature predictions is evaluated. Comparisons of computational and experimental data demonstrates the capability of the method for predicting inviscid solutions useful for high speed calculations about simple 3-D geometries. The approach has promising features and results indicate potential for application to more complex configurations. The mesh generation is based on the advancing front technique, and steady state solutions of the Euler equations are achieved by explicit time integration. Spatial discretization uses the Taylor-Galerkin approach; an alternate time integration, based on the Runge-Kutta method, is also included. The solution-adaptive grid procedure is based on either remeshing or mesh refinement techniques. An alternative geometry-adaptive grid procedure has also been incorporated.

Djomehri, M. J.↗

Spaceflight optical disk recorder development

Mass memory systems based on rewriteable optical disk media are expected to play an important role in meeting the data system requirements for future NASA spaceflight missions. NASA has established a program to develop a high performance (high rate, large capacity) optical disk recorder focused on use aboard unmanned Earth orbiting platforms. An expandable, adaptable system concept is proposed based on disk drive modules and a modular controller. Drive performance goals are 10 gigabyte capacity, 300 megabit/s transfer rate, 10 exp -12 corrected bit error rate, and 150 millisec access time. This performance is achieved by writing eight data tracks in parallel on both sides of a 14 in. optical disk using two independent heads. System goals are 160 gigabyte capacity, 1.2 gigabits/s data rate with concurrent I/O, 250 millisec access time, and two to five year operating life on orbit. The system can be configured to meet various applications. This versatility is provided by the controller. The controller provides command processing, multiple drive synchronization, data buffering, basic file management, error processing, and status reporting. Technology developments, design concepts, current status including a computer model of the system and a Controller breadboard, and future plans for the Drive and Controller are presented.

Jurczyk, Stephen G.↗

A method of predicting quasi-steady aerodynamics for flutter analysis of high speed vehicles using steady CFD calculations

High speed linear aerodynamic theories like piston theory and Newtonian impact theory are relatively inexpensive to use for flutter analysis. These theories have limited areas of applicability depending on the configuration and the flow conditions. In addition, these theories lack the ability to capture viscous, shock, and real gas effects. CFD methods can model all of these effects accurately, but the unsteady calculations required for flutter are expensive and often impractical. This paper describes a method for using steady CFD calculations to approximate the generalized aerodynamic forces for a flutter analysis. Example two-and three-dimensional aerodynamic force calculations are provided. In addition, a flutter analysis of a NASP-type wing will be discussed.

Scott, Robert C.↗

A 500 megabyte/second disk array

Applications at the Army High Performance Computing Research Center's (AHPCRC) Graphic and Visualization Laboratory (GVL) at the University of Minnesota require a tremendous amount of I/O bandwidth and this appetite for data is growing. Silicon Graphics workstations are used to perform the post-processing, visualization, and animation of multi-terabyte size datasets produced by scientific simulations performed of AHPCRC supercomputers. The M.A.X. (Maximum Achievable Xfer) was designed to find the maximum achievable I/O performance of the Silicon Graphics CHALLENGE/Onyx-class machines that run these applications. Running a fully configured Onyx machine with 12-150MHz R4400 processors, 512MB of 8-way interleaved memory, 31 fast/wide SCSI-2 channel each with a Ciprico disk array controller we were able to achieve a maximum sustained transfer rate of 509.8 megabytes per second. However, after analyzing the results it became clear that the true maximum transfer rate is somewhat beyond this figure and we will need to do further testing with more disk array controllers in order to find the true maximum.

Ruwart, Thomas M.↗

Accurate Modeling of the Postbuckling Response of Composite Panels with Skewed Stiffeners

Modeling procedures which predict accurately the postbuckling response of composite panels with skewed stiffeners are presented. A particular experimental program is considered and detailed finite element models are created to represent the conditions in the experiment. First, a simple baseline model with minimal detail is defined. Then, a number of modeling refinements that improve the accuracy of the model are identified. These refinements are applied individually to the baseline model to assess the effect of each refinement on the predicted response. The individual refinements are then combined to create an advanced finite element model. In addition to model refinements which affect the overall panel response, a modeling procedure for simulating nonuniform initial load introduction that is specific to an particular experiment is described and demonstrated. By implementing a number of modeling refinements, a finite element model is developed which improves the correlation between the measured and predicted responses. The skewed stiffener detail and anisotropic skin in the selected problem create axial-shear stiffness coupling which makes this problem sensitive to the constraint on the shear displacement. The remainder of the modeling refinements considered are applicable to general structural configurations. The results presented may be used to guide future efforts to improve correlation between predicted and measured responses for post buckled stiffened panels.

Young, Richard D.↗

A Flight Study of a Power-Off Landing Technique Applicable to Re-Entry Vehicles

A power-off landing technique, applicable to aircraft of configurations presently being considered for manned re-entry vehicles, has been developed and flight tested at Ames Research Center. The flight tests used two configurations of an airplane for which the values of maximum lift-drag ratios were 4.0 and 2.8. Twenty-four idle-power approaches were made to an 8000-foot runway with touchdown point and airspeed accuracies of +/-600 feet and +/-10 knots, respectively. The landing pattern used was designed to provide an explicitly defined flight path for the pilot and, yet, to require no external guidance other than the pilot's view from the cockpit. The initial phase of the approach pattern is a constant high-speed descent from altitude aimed at a ground reference point short of the runway threshold. At a specified altitude and speed, a constant g pull-out is made to a shallow flight path along which the air-plane decelerates to the touchdown point. Repeatability and safety are inherent because of the reduced number of variables requiring pilot judgment, and because of the fact that a missed approach is evident at speeds and altitudes suitable for safe ejection. The accuracy and repeatability of the pattern are indicated by the measured results. The proposed pattern appears to be particularly suitable for configurations having unusual drag variations with speed in the lower speed regime, since the pilot is not required to control speed in the latter portions of the pattern.

Bray, Richard S.↗

Task Assignment Heuristics for Distributed CFD Applications

CFD applications require high-performance computational platforms: 1. Complex physics and domain configuration demand strongly coupled solutions; 2. Applications are CPU and memory intensive; and 3. Huge resource requirements can only be satisfied by teraflop-scale machines or distributed computing.

Lopez-Benitez, N.↗

Comparison of Acoustic Impedance Eduction Techniques for Locally-Reacting Liners

Typical acoustic liners used in current aircraft inlets and aft-fan ducts consist of some type of perforated facesheet bonded to a honeycomb core. A number of techniques for determining the acoustic impedance of these locallyreacting liners have been developed over the last five decades. In addition, a number of models have been developed to predict the acoustic impedance of locallyreacting liners in the presence of grazing flow, and to use that information together with aeroacoustic propagation codes to assess the noise absorption provided by these liners. These prediction models have incorporated the results from databases acquired with specific impedance eduction techniques. Thus, while these prediction models are acceptable for liners that are similar to those tested in these databases, their application to new liner configurations must be viewed with caution. The primary purpose of this paper is to provide a comparison of impedance eduction techniques that have been implemented at various aerospace research laboratories in the United States (NASA Langley Research Center, General Electric Aircraft Engines, B. F. Goodrich and Boeing). A secondary purpose is to provide data for liner configurations that extend the porosity range beyond that which has been previously used in common aircraft engine nacelles. Two sets of liners were designed to study the effects of three parameters: perforate hole diameter, facesheet thickness and porosity. These two sets of liners were constructed for testing in each of the laboratories listed above. The first set of liners was designed to fit into the NASA Langley and Boeing test facilities. The second set was designed to fit into the General Electric Aircraft Engines and B. F. Goodrich test facilities. By using the same parent material, both sets of liners were identical to within the limits of material and fabrication variability. Baseline data were obtained in the normal incidence impedance tubes at NASA Langley and B. F. Goodrich. The results were found to compare extremely well. The samples were then tested in the grazing flow ducts of each of the four laboratories. Perhaps the most significant result of these comparisons is that the educed acoustic resistances for the liners used in this study increase as the mean flow profile is modified from uniform to 3-D shear. This realization has demonstrated the need for an frequency-dependent impedance eduction technique that incorporates 3-D shear flow and is efficient.

Jones, M. G.↗

Computational Methods for Dynamic Stability and Control Derivatives

Force and moment measurements from an F-16XL during forced pitch oscillation tests result in dynamic stability derivatives, which are measured in combinations. Initial computational simulations of the motions and combined derivatives are attempted via a low-order, time-dependent panel method computational fluid dynamics code. The code dynamics are shown to be highly questionable for this application and the chosen configuration. However, three methods to computationally separate such combined dynamic stability derivatives are proposed. One of the separation techniques is demonstrated on the measured forced pitch oscillation data. Extensions of the separation techniques to yawing and rolling motions are discussed. In addition, the possibility of considering the angles of attack and sideslip state vector elements as distributed quantities, rather than point quantities, is introduced.

Green, Lawrence L.↗

Computational Methods for Dynamic Stability and Control Derivatives

Force and moment measurements from an F-16XL during forced pitch oscillation tests result in dynamic stability derivatives, which are measured in combinations. Initial computational simulations of the motions and combined derivatives are attempted via a low-order, time-dependent panel method computational fluid dynamics code. The code dynamics are shown to be highly questionable for this application and the chosen configuration. However, three methods to computationally separate such combined dynamic stability derivatives are proposed. One of the separation techniques is demonstrated on the measured forced pitch oscillation data. Extensions of the separation techniques to yawing and rolling motions are discussed. In addition, the possibility of considering the angles of attack and sideslip state vector elements as distributed quantities, rather than point quantities, is introduced.

Green, Lawrence L.↗

Policy-Based Management Natural Language Parser

The Policy-Based Management Natural Language Parser (PBEM) is a rules-based approach to enterprise management that can be used to automate certain management tasks. This parser simplifies the management of a given endeavor by establishing policies to deal with situations that are likely to occur. Policies are operating rules that can be referred to as a means of maintaining order, security, consistency, or other ways of successfully furthering a goal or mission. PBEM provides a way of managing configuration of network elements, applications, and processes via a set of high-level rules or business policies rather than managing individual elements, thus switching the control to a higher level. This software allows unique management rules (or commands) to be specified and applied to a cross-section of the Global Information Grid (GIG). This software embodies a parser that is capable of recognizing and understanding conversational English. Because all possible dialect variants cannot be anticipated, a unique capability was developed that parses passed on conversation intent rather than the exact way the words are used. This software can increase productivity by enabling a user to converse with the system in conversational English to define network policies. PBEM can be used in both manned and unmanned science-gathering programs. Because policy statements can be domain-independent, this software can be applied equally to a wide variety of applications.

James, Mark↗

Rapid Parameterization Schemes for Aircraft Shape Optimization

A rapid shape parameterization tool called PROTEUS is developed for aircraft shape optimization. This tool can be applied directly to any aircraft geometry that has been defined in PLOT3D format, with the restriction that each aircraft component must be defined by only one data block. PROTEUS has eight types of parameterization schemes: planform, wing surface, twist, body surface, body scaling, body camber line, shifting/scaling, and linear morphing. These parametric schemes can be applied to two types of components: wing-type surfaces (e.g., wing, canard, horizontal tail, vertical tail, and pylon) and body-type surfaces (e.g., fuselage, pod, and nacelle). These schemes permit the easy setup of commonly used shape modification methods, and each customized parametric scheme can be applied to the same type of component for any configuration. This paper explains the mathematics for these parametric schemes and uses two supersonic configurations to demonstrate the application of these schemes.

Li, Wu↗

Applying a Stitched, Rod-Stiffened Concept to Heavily Loaded Structure

NASA and the Boeing Company have worked to develop new low-cost, light-weight composite structures for aircraft. A stitched carbon-epoxy material system was developed to reduce the weight and cost of transport aircraft wing structure, first in the NASA Advanced Composites Technology (ACT) program in the 1990's and now in the Environmentally Responsible Aviation (ERA) Project. By stitching through the thickness of a dry carbon fiber material prior to cure, the labor associated with panel fabrication and assembly can be significantly reduced and the need for mechanical fasteners is almost eliminated. Stitching provides the benefit of reducing or eliminating delaminations, including those between stiffener flanges and skin. Stitching also reduces part count, and therefore, cost of the structure. The stitched panel concept used in the ACT program in the 1990's used simple blade-stiffeners as stringers, caps and clips. Today, the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept is being developed for application to advanced vehicle configurations. PRSEUS provides additional weight savings through the use of a stiffener with a thin web and a unidirectional carbon rod at the top of the web which provides structurally efficient stiffening. A comparison between the blade-stiffened structure and PRSEUS is presented focusing on highly loaded structure and demonstrating improved weight reduction.

Jegley, Dawn C.↗

Enabling Technologies for Entrepreneurial Opportunities in 3D printing of SmallSats

A consortium of innovative experts in additive manufacturing (AM) comprising Northrup Grumman Technical Services, University of Texas at El Paso (UTEP), Configurable Space Microsystems Innovations & Applications Center (COSMIAC), NASA Glenn Research Center (GRC), and Youngstown State University, have made significant breakthroughs in the goal of creating the first complete 3D printed small satellite. Since AM machines are relatively inexpensive, this should lead to many entrepreneurial opportunities for the small satellite community. Our technology advancements are focused on the challenges of embedding key components within the structure of the article. We have demonstrated, using advanced fused deposition modeling techniques, complex geometric shapes which optimize the spacecraft design. The UTEP Keck Center has developed a method that interrupts the printing process to insert components into specific cavities, resulting in a spacecraft that has minimal internal space allocated for what traditionally were functional purposes. This allows us to increase experiment and instrument capability by provided added volume in a confined small satellite space. Leveraging initial progress made on a NASA contract, the team investigated the potential of new materials that exploit the AM process, producing candidate compositions that exceed the capabilities of traditional materials. These "new materials" being produced and tested include some that have improved radiation shielding, increased permeability, enhanced thermal properties, better conductive properties, and increased structural performance. The team also investigated materials that were previously not possible to be made. Our testing included standard mechanical tests such as vibration, tensile, thermal cycling, and impact resistance as well as radiation and electromagnetic tests. The initial results of these products and their performance will be presented and compared with standard properties. The new materials with the highest probability to disrupt the future of small satellite systems by driving down costs will be highlighted, in conjunction with the electronic embedding process.

Communications↗

Applying a Stiffened Stitched Concept to Shear-Loaded Structure

NASA and The Boeing Company have worked to develop new low-cost, lightweight composite structures for aircraft. A stitched carbon-epoxy material system was developed to reduce the weight and cost of transport aircraft structure, first in the NASA Advanced Composites Technology (ACT) Program in the 1990's and now in the Environmentally Responsible Aviation (ERA) Project. By stitching through the thickness of a dry carbon fiber material prior to cure, the need for mechanical fasteners is almost eliminated. Stitching also provides the benefit of reducing or eliminating delaminations, including those between stiffener flanges and skin. The stitched panel concept used in the ACT program used simple blade-stiffeners as stringers, caps, and clips. Today, the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept is being developed for application to advanced vehicle configurations. PRSEUS provides additional weight savings through the use of a stiffener with a thin web and a unidirectional carbon rod at the top of the web which provides structurally efficient stiffening. Comparisons between stitched and unstitched structure and between blade-stiffened and rod-stiffened structure are presented focusing on a panel loaded in shear. Shear loading is representative of spar loading in wing structures.

Jegley, Dawn C.↗

Reconstruction of a Broadband Spectrum of Alfvenic Fluctuations

Alfvenic fluctuations in the solar wind exhibit a high degree of velocities and magnetic field correlations consistent with Alfven waves propagating away and toward the Sun. Two remarkable properties of these fluctuations are the tendencies to have either positive or negative magnetic helicity (-1 less than or equal to sigma(sub m) less than or equal to +1) associated with either left- or right- topological handedness of the fluctuations and to have a constant magnetic field magnitude. This paper provides, for the first time, a theoretical framework for reconstructing both the magnetic and velocity field fluctuations with a divergence-free magnetic field, with any specified power spectral index and normalized magnetic- and cross-helicity spectrum field fluctuations for any plasma species. The spectrum is constructed in the Fourier domain by imposing two conditions-a divergence-free magnetic field and the preservation of the sense of magnetic helicity in both spaces-as well as using Parseval's theorem for the conservation of energy between configuration and Fourier spaces. Applications to the one-dimensional spatial Alfvenic propagation are presented. The theoretical construction is in agreement with typical time series and power spectra properties observed in the solar wind. The theoretical ideas presented in this spectral reconstruction provide a foundation for more realistic simulations of plasma waves, solar wind turbulence, and the propagation of energetic particles in such fluctuating fields.

waves↗