Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSION BUCKLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

An integrating matrix formulation for buckling of rotating beams including the effects of concentrated masses

The integrating matrix technique of computational mechanics is extended to include the effects of concentrated masses. The stability of a flexible rotating beam with discrete masses is analyzed to determine the critical rotational speeds for buckling in the inplane and out-of-plane directions. In this problem, the beam is subjected to compressive centrifugal forces arising from steady rotation about an axis which does not pass through the clamped end of the beam. To determine the eigenvalues from which stability is assessed, the differential equations of motion are solved numerically by combining the extended integrating matrix method with an eigenanalysis. Stability boundaries for a discrete mass representation of a uniform beam are shown to asymptotically approach the stability boundaries for the corresponding continuous mass beam as the number of concentrated masses is increased. An error in the literature is also noted for the discrete mass problem concerning the behavior of the critical rotational speed for inplane buckling as the radius of rotation of the clamped end of the beam is reduced.

Lakin, William D.↗

CoCrMo cellular structures made by Electron Beam Melting studied by local tomography and finite element modelling

The work focuses on the structural and mechanical characterization of Co-Cr-Mo cellular samples with cubic pore structure made by Electron Beam Melting (EBM). X-ray tomography was used to characterize the architecture of the sample. High resolution images were also obtained thanks to local tomography in which the specimen is placed close to the X-ray source. These images enabled to observe some defects due to the fabrication process: small pores in the solid phase, partially melted particles attached to the surface. Then, in situ compression tests were performed in the tomograph. The images of the deformed sample show a progressive buckling of the vertical struts leading to final fracture. The deformation initiated where the defects were present in the strut i.e. in regions with reduced local thickness. The finite element modelling confirmed the high stress concentrations of these weak points leading to the fracture of the sample. - Highlights: • CoCrMo samples fabricated by Electron Beam Melting (EBM) process are considered. • X-ray Computed Tomography is used to observe the structure of the sample. • The mechanical properties are tested thanks to an in situ test in the tomograph. • A finite element model is developed to model the mechanical behaviour.

36 MATERIALS SCIENCE↗

Designing interlayers to improve the mechanical reliability of transparent conductive oxide coatings on flexible substrates

In this study, we investigate the effect of interlayers on the mechanical properties of transparent conductive oxide (TCO) on flexible polymer substrates. Indium tin oxide (ITO), which is the most widely used TCO film, and Ti, which is the most widely used adhesive interlayer, are selected as the coating and the interlayer, respectively. These films are deposited on the polymer substrates using dc-magnetron sputtering to achieve varying thicknesses. The changes in the following critical factors for film cracking and delamination are analyzed: the internal stress ({sigma}{sup i}) induced in the coatings during deposition using a white light interferometer, the crystallinity using a transmission electron microscope, and the surface roughness of ITO caused by the interlayer using an atomic force microscope. The resistances to the cracking and delamination of ITO are evaluated using a fragmentation test. Our tests and analyses reveal the important role of the interlayers, which significantly reduce the compressive {sigma}{sup i} that is induced in the ITO and increase the resistance to the buckling delamination of the ITO. However, the relaxation of {sigma}{sup i} is not beneficial to cracking because there is less compensation for the external tension as {sigma}{sup i} further decreases. Based on these results, the microstructural control is revealed as a more influential factor than {sigma}{sup i} for improving crack resistance.

36 MATERIALS SCIENCE↗

Postbuckling behavior of axially compressed graphite-epoxy cylindrical panels with circular holes

The results of an experimental and analytical study of the effects of circular holes on the postbuckling behavior of graphite-epoxy cylindrical panels loaded in axial compression are presented. The STAGSC-1 general shell analysis computer code is used to determine the buckling and postbuckling response of the panels. The loaded, curved ends of the specimens were clamped by fixtures and the unloaded, straight edges were simply supported by knife-edge restraints. The panels are loaded by uniform end shortening to several times the end shortening at buckling. The unstable equilibrium path of the postbuckling response is obtained analytically by using a method based on controlling an equilibrium-path-arc-length parameter instead of the traditional load parameter. The effects of hole diameter, panel radius, and panel thickness on postbuckling response are considered in the study. Experimental results are compared with the analytical results and the failure characteristics of the graphite-epoxy panels are described.

Knight, N. F., Jr.↗

Stability of elastically supported columns

A criterion is developed for the stiffness required of elastic lateral supports at the ends of a compression member to provide stability. A method based on this criterion is then developed for checking the stability of a continuous beam-column. A related method is also developed for checking the stability of a member of a pin-jointed truss against rotation in the plane of the truss.

COMPRESSION MEMBERS-STABILITY↗

Structural efficiency studies of corrugated compression panels with curved caps and beaded webs

Curved cross-sectional elements are employed in structural concepts for minimum-mass compression panels. Corrugated panel concepts with curved caps and beaded webs are optimized by using a nonlinear mathematical programming procedure and a rigorous buckling analysis. These panel geometries are shown to have superior structural efficiencies compared with known concepts published in the literature. Fabrication of these efficient corrugation concepts became possible by advances made in the art of superplastically forming of metals. Results of the mass optimization studies of the concepts are presented as structural efficiency charts for axial compression.

Davis, R. C.↗

Salt Tank Testbed: a Test Site Designed to Replicate Floor Buckles Observed in Commercial TES Tanks

A test site has been designed and is under construction to replicate the buckling failure ob-served in several in-service storage tanks for nitrate salts operating up to 565°C. In commercial tanks multiple factors have been identified that influence the floors susceptibility to buck-ling, including: the as-manufactured shape of the floor, high compressive stresses due to thermal gradients and/or friction, fluid inventory and absolute temperature. Based on exten-sive modeling analysis it was determined that similar buckles can be reproduced in a scaled test tank (approximately 9x smaller than a representative commercial tank design). To buckle the scaled tank a radial thermal gradient is generated in the tank with a low fluid level, the fluid level is then increased while maintaining the thermal gradient; based on the modeling results just one of these cycles can plastically deform the tank floor. The test site which is under construction is designed to replicate this damaging cycle at lower temperatures. The goal of testing will be to reproduce this damaging cycle and buckle the scaled test tank floor, allowing proper model validation and a methodology for comparing different tank designs at a smaller (and less costly) scale.

25 ENERGY STORAGE↗

Determining Compression Characteristics of Honeycomb Material - 19674

The objective is to determine compression test characteristics of stainless steel honeycomb material to be able to represent honeycomb structures accurately in analytical models used to simulate hypothetical accident scenarios of shipping packages. Honeycomb is a material used primary in the aerospace industry due to its high strength-to-weight ratio. Because it doesn't have a shelf life and can withstand high heats, it is an excellent candidate for a structural material in package designs. Honeycomb has orthotropic material properties. The honeycomb currently being evaluated is made of metal ribbons spot welded together to form hexagon pattern between metal plates. The hexagon ribbons are brazed to the metal plates. The complexity of the honeycomb significantly lengthens the simulation time, which is further complicated when the brazing, welding, and imperfections of the material is considered. This means to affectively represent the honeycomb in simulation programs, such as Abaqus, the material needs to be approximated as a uniform orthotropic material. This requires material properties in each of the three directions, T, W, and L. The T direction is defined as the 'strong' direction, perpendicular to the honeycomb sheet. The L direction is parallel the ribbon and the W direction is perpendicular to the ribbon. Honeycomb has 3 different compression stages. Stage 1 is the initial compression where the honeycomb maintains its structural integrity and does not permanently deform from loads from normal operations. Stage 2 is when the initial buckling causes irreversible damage to the honeycomb. Stage 2 is the one we are most interested in because it absorbs the most energy from a hypothetical accident scenario. During Stage 2, the honeycomb fails layer-by-layer, indicating that the more layers, the longer material crushing is sustained, and thus the more energy that is absorbed. Stage 3 is final compression, similar to compressing solid metal. During stage 3 the stress increases with a diminishing rate of elongation and the honeycomb is completely failed where the plates between the honeycomb core sandwich the crushed honeycomb ribbon. The stress-strain graph bellow shows compression test of 3 different samples in the T direction. The red lines divide the three stages. The far left is Stage 1, the middle stage 2, and the right stage 3. The data collected is displayed in the table below. The expressions in the table represent the regression formula that represents each stage of the compression on a stress-strain graph. Stage 1 is assumed to intersect with the origin; data for stage 3 for the crush in W and L directions where unable to be gathered due to the nature of failure for those directions. Stage 1 and 2 are linear regressions while stage 3 is a degree 2, to best match the curve. Linear regression is used on stage 2 because ultimately that represents the energy absorbed. With more data, a degree n x 2 regression would be a more appropriate regression for stage 2, where n is the number of layers. The table below is the approximation of each scenario and stage. Each stage starts and ends at the intersection of the next stage. There where two main objectives for these tests: firstly to understand how honeycomb performs under extreme compression, and secondly to be able to numerically represent the honeycomb structure. Both of these where completed to varying degrees. It is important understood how the honeycomb fails. If it is crushed in the T direction it retains its integrity even after being crushed, however when crushed in the L and W crush direction, if it fails, it disintegrates, and loses all integrity. Also, the more layers the more time the material spends in stage 2. Failure is started by buckling, thus if there is any imperfection, the stress will not spike but transition straight into stage 2. The data collected and aggregated can be used for initial simulation of honeycomb used in packages. The initial testing has set the ground work for more data to be collected in order to verify results and to allow more confidence in the simulation results. This is only the initial data collected. The next steps is to continue to collect more data to verify results and to test more variants of honeycomb, with different brazing, layers, and shape.

36 MATERIALS SCIENCE↗

The behavior of delaminations in composite plates - Analytical and experimental results

The behavior of elliptical sublaminates created by delaminations in composite plates was investigated for plates subjected to in-plane compressive, shear, and thermal loads. The axes of the ellipse may be arbitrarily oriented with respect to the applied loads. A model was developed which provides the stresses, strains, and displacements of the sublaminate, and the loads applied to the plate at which the sublaminate buckles and at which it grows in size. A series of experiments was conducted on sandwich plates made of Fiberite T300/976 graphite-epoxy laminates bonded to an aluminum honeycomb core. Teflon film in either a circle or an ellipse was embedded in the laminate, simulating the presence of a delamination. Each plate was loaded in compression, and the load-strain history of the sublaminate, the sublaminate buckling load, and the sublaminate growth load were measured. The predictions of the model agreed reasonably well with the data.

Peck, Scott O.↗

Modeling thin film, buckle-driven delamination along a metal/polymer interface in a stressed overlayer test.

Interfacial delamination is often the critical failure mode limiting the performance of polymer/metal interfaces. Consequently methods that measure the toughness of such interfaces are of considerable interest. One approach for measuring the toughness of a polymer/metal interface is to use the stressed-overlayer test. In this test a metal substrate is coated with a sub-micron thick polymer film to create the interface of interest. An overlayer, typically a few tenths of a micron of sputtered tungsten, is then deposited on top of the polymer in such a way as to generate a very high residual compressive stress within the sputtered layer ({approx} 1-2 GPa). This highly stressed overlayer induces delamination and blister formation. The measured buckle heights and widths are then used in conjunction with a fracture mechanics analysis to infer interfacial toughness. Here we use a finite element, cohesive-zone-based, fracture analysis to perform the required interfacial crack growth simulation. This analysis shows that calculated crack growth is sensitive to the polymer layer thickness even when the layer is only 10's of nanometers thick. The inward displacement of the overlayer at the buckle edge, which is enabled by the relatively low polymer compliance, is the primary cause of differences from a rigid substrate idealization.

36 MATERIALS SCIENCE↗

Active control of buckling of flexible beams

The feasibility of using the rapidly growing technology of the shape memory alloys actuators in actively controlling the buckling of large flexible structures is investigated. The need for such buckling control systems is becoming inevitable as the design trends of large space structures have resulted in the use of structural members that are long, slender, and very flexible. In addition, as these truss members are subjected mainly to longitudinal loading they become susceptible to structural instabilities due to buckling. Proper control of such instabilities is essential to the effective performance of the structures as stable platforms for communication and observation. Mathematical models are presented that simulate the dynamic characteristics of the shape memory actuator, the compressive structural members, and the associated active control system. A closed-loop computer-controlled system is designed, based on the developed mathematical models, and implemented to control the buckling of simple beams. The performance of the computer-controlled system is evaluated experimentally and compared with the theoretical predictions to validate the developed models. The obtained results emphasize the importance of buckling control and suggest the potential of the shape memory actuators as attractive means for controlling structural deformation in a simple and reliable way.

Baz, A.↗

Optimum design of laminated plates under axial compression

The paper presents a method for designing laminated plates with orthotropic layers under uniaxial and biaxial compression. The objective is to find the fiber direction of all the layers that give the highest buckling stress; therefore, it is necessary to solve an unconstrained maximization problem. The optimization technique used is Powell's conjugate direction method. Numerical calculations were made for plates with three, four, and six layers.

Hirano, Y.↗

Structural efficiency study of graphite-epoxy aircraft rib structures

Attention is given to the structural efficiencies obtainable with optimally designed graphite/epoxy wing rib panel configurations that are potentially economically manufacturable. Some ribs are commonly used as fuel cell closeout panels, and are accordingly subjected to out-of-plane pressure loads in addition to the in-plane axial compressive and shear loads resulting from the wing loading. The present minimum-weight panel designs satisfy buckling and strength constraints for wing rib panels subjected to a wide range of combined load conditions.

Swanson, Gary D.↗

On the Accuracy of Probabilistic Bucking Load Prediction

The buckling strength of thin-walled stiffened or unstiffened, metallic or composite shells is of major concern in aeronautical and space applications. The difficulty to predict the behavior of axially compressed thin-walled cylindrical shells continues to worry design engineers as we enter the third millennium. Thanks to extensive research programs in the late sixties and early seventies and the contributions of many eminent scientists, it is known that buckling strength calculations are affected by the uncertainties in the definition of the parameters of the problem such as definition of loads, material properties, geometric variables, edge support conditions, and the accuracy of the engineering models and analysis tools used in the design phase. The NASA design criteria monographs from the late sixties account for these design uncertainties by the use of a lump sum safety factor. This so-called 'empirical knockdown factor gamma' usually results in overly conservative design. Recently new reliability based probabilistic design procedure for buckling critical imperfect shells have been proposed. It essentially consists of a stochastic approach which introduces an improved 'scientific knockdown factor lambda(sub a)', that is not as conservative as the traditional empirical one. In order to incorporate probabilistic methods into a High Fidelity Analysis Approach one must be able to assess the accuracy of the various steps that must be executed to complete a reliability calculation. In the present paper the effect of size of the experimental input sample on the predicted value of the scientific knockdown factor lambda(sub a) calculated by the First-Order, Second-Moment Method is investigated.

Arbocz, Johann↗