Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMBUSTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

CO Laser Absorption Measurements During Syngas Combustion at High Pressure

Abstract Syngas is a desirable fuel for combustion in the Allam-Fetvedt cycle, which involves combustion under supercritical-CO2 conditions. While some work has been conducted in collecting ignition delay times (IDT) at the extreme pressures required by these systems, significant model deficiencies remain. Additionally, considerable barriers in terms of nonideal gas dynamic effects have been shown for these experiments in shock tubes. Further investigation into the fundamental combustion kinetics of H2/CO/CO2 mixtures is required. Time-resolved speciation measurements for target species have been shown to better aid in improving the understanding of underlying chemical kinetics than global ignition delay time measurements. Therefore, laser absorption measurements of CO were measured behind reflected shock waves during combustion of syngas at 5 and 10 bar and temperatures between 1080 and 2100 K. The mixtures investigated utilized H2-to-CO ratios of 1:1 and 1:4, respectively, each at stoichiometric conditions, allowing for discussions of the effect of initial fuel composition. A ratio of fuel to CO2 of 1:2 was also utilized to represent commercially available syngas. The mixtures were diluted in helium and argon (20% He, 76.5% Ar) to minimize thermal effects and to expedite CO thermal relaxation during the experiment. The resulting CO time histories were then compared to modern chemical kinetics mechanisms, and disagreement is seen for this system, which is assumed to be fairly well known. This study elucidates particular chemistry that needs improvement in moving toward a better understanding of syngas combustion at elevated pressures.

Engineering↗
DOE OSTI2025

Selective chemical looping combustion of acetylene in ethylene-rich streams

Here, the requirement for C 2 H 2 concentrations below 2 parts per million (ppm) in gas streams for C 2 H 4 polymerization necessitates its semihydrogenation to C 2 H 4 . Here, we demonstrate selective chemical looping combustion of C 2 H 2 in C 2 H 4 -rich streams by Bi 2 O 3 as an alternative catalytic pathway to reduce C 2 H 2 concentration below 2 ppm. Bi 2 O 3 combusts C 2 H 2 with a first-order rate constant that is 3000 times greater than the rate constant for C 2 H 4 combustion. In successive redox cycles, the lattice O of Bi 2 O 3 can be fully replenished without discernible changes in local Bi coordination or C 2 H 2 combustion selectivity. Heterolytic activation of C–H bonds across Bi–O sites and the higher acidity of C 2 H 2 results in lower barriers for C 2 H 2 activation than C 2 H 4 , enabling selective catalytic hydrocarbon combustion leveraging differences in molecular deprotonation energies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A High Specific Output Gasoline Low Temperature Combustion Engine

This report summarizes activities conducted in support of the project “A High Specific Output Gasoline Low Temperature Combustion Engine” under COOPERATIVE AGREEMENT NUMBER DE-EE0007788. This cooperative agreement was structured as a 51%/49% recipient/DOE NETL cost share with two Go / no-Go decision gates spanning three budget periods. The primary objective of the program is the development and demonstration of a downsized boosted, lean, low temperature gasoline combustion engine system capable of demonstrating a 15-17% fuel economy improvement relative to a contemporary naturally aspirated stoichiometric combustion engine consistent with relevant emissions constraints and the use of marketplace gasolines. The program focused on maximizing internal combustion engine fuel economy potential by combining the benefits of downsized boosted engine technology with next generation gasoline lean-burn, low temperature combustion and novel low temperature plasma ignition. The project achieved a 20.5% improvement from hot FTP cycle test and 18.9% improvement from cold FTP cycle test while meeting stringent SULEV30 emissions regulation for both test cycles (HOT FTP: 15.37 mg of NOx+HC; 0.16 g/mile of CO, COLD FTP: 23.1 mg of NOx+HC; 0.33 g/mile of CO).

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Full-Loop Simulation of the Combustion of Biomass in a Circulating Fluidized Bed Combustor

Interest in circulating fluidized bed (CFB) boilers as a power generation technology has skyrocketed in recent years because of several advantages this technology offers over conventional boilers, such as increased gas-solid mixing, which results in higher combustion efficiency, and the ability to use lower rank fuels. CFB combustors are operated at lower temperatures than conventional thermal power generation combustors, thus reducing NO x emissions, while SO 2 emissions can be conveniently controlled through the addition of Ca-based sulfur sorbents within the combustor. This report summarizes the development of a comprehensive computational fluid dynamics (CFD) model for biomass combustion in a 50 kW th CFB combustor employing the multiphase particle-in-cell (PIC) approach in the open-source Multiphase Flow with Interphase eXchanges (MFiX) Software Suite at the U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL). The experimental combustor was designed, built, and operated at CanmetENERGY, Natural Resources Canada in Ottawa, Canada. This work is the culmination of a multi-year collaboration between NETL and CanmetENERGY. The hydrodynamics in the full loop are validated against cold-flow experiments conducted at CanmetENERGY. To mimic the dense packing in the standpipe in the absence of a collisional model in the MFiX-PIC approach, the ram valve in the return leg is partially closed to obstruct the flow. A combustion reaction scheme was developed that considers the volatiles released by the fuel as a lumped species that fully converts to CO 2 and H 2 O. The so-called enhanced simplified combustion scheme produces an excellent match with experimental data in terms of the species concentrations of CO 2 and O 2 at the outlet and the freeboard, demonstrating the utility of the comprehensive model for a range of flow conditions and operating temperatures. Furthermore, the model can be readily adapted to simulate combustion of a variety of biomass fuels as well as co-fired systems under air and oxy-fuel conditions.

09 BIOMASS FUELS↗
DOE OSTI2023

Exploration of Fuel Property Impacts on the Combustion of Late Post Injections Using Binary Blends and High-Reactivity Ether Bioblendstocks

In this study, the impacts of fuel volatility and reactivity on com- bustion stability and emissions were studied in a light-duty single- cylinder research engine for a three-injection catalyst heating oper- ation strategy with late post-injections. N-heptane and blends of farnesane/2,2,4,4,6,8,8-heptamethylnonane were used to study the im- pacts of volatility and reactivity. The effect of increased chemical reac- tivity was also analysed by comparing the baseline #2 diesel operation with a pure blend of mono-ether components (CN > 100) representa- tive of potential high cetane oxygenated bioblendstocks and a 25 vol.% blend of the mono-ether blend and #2 diesel with a cetane number (CN) of 55. At constant reactivity, little to no variation in combustion performance was observed due to differences in volatility, whereas in- creased reactivity improved combustion stability and efficiency at late injection timings. Fuels with higher reactivity were found to reduce engine-out hydrocarbon and carbon monoxide emissions while also achieving stable combustion at post-injection timings later than those achievable with #2 diesel fuel. The pure ether blend had the latest achievable post-injection timing of +30.5 CAD while still maintaining stable combustion (coefficient of variation of gross-indicated mean ef- fective pressure < 5%). With post-injection timing adjusted to achieve a matched exhaust temperature of 300 °C, the ether-diesel CN 55 blend was observed to have slightly higher thermal efficiency in comparison to the baseline #2 diesel fuel. The results also indicate that cetane num- ber may serve as a good indicator of combustion characteristics at late injection timings used for aftertreatment thermal management opera- tion.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

Modifications to Solar Titan-130 Combustion Systems for Efficient, High Turndown Operation

The project team of Southwest Research Institute® (SwRI®), Solar Turbines Incorporated (Solar), the Electric Power Research Institute (EPRI), the University of California, Irvine (UCI), and the Georgia Institute of Technology (Georgia Tech) investigated methods to allow higher efficiency part-load operation of a Solar Titan 130 gas turbine. The objective was to develop a low-emission combustion system capable of sustaining combustion and avoiding lean blowout during high turndown operation, which would allow the gas turbine to operate as efficiently as possible at part load. Currently, electric utility markets are beginning to experience substantial increases in renewable energy generation. Some of these renewable energy sources have highly variable output in an uncontrolled manner. In order to maintain grid stability, there is a need for power plants to ramp up power to the grid rapidly to make up for drops in renewable generation. This is often termed spinning reserve, but the size of this reserve may need to increase as renewable penetration into the electric utility market increases. Small combined heat and power (CHP) power plants provide a promising option for meeting this spinning reserve requirement. In order to operate in spinning reserve while still meeting the heat requirements for the CHP, the gas turbine needs to operate efficiently at very low loads. Efficient, high turndown operations in this engine are limited by the lean flammability limit of the premixed combustion system. This project sought enhance the lean operability range of the Titan 130 combustor. First, the project team participated in a brainstorming activity and ultimately selected two concepts to explore: fuel augmentation with hydrogen (H2) to improve the stability at lean operating conditions and modifications to the fuel nozzle to improve the emissions performance at lean operating conditions. Analytical and laboratory investigations were accomplished by UCI to investigate the efficacy of H2 addition at improving lean blow out (LBO) limits and the resulting emissions. These investigations used a variety of chemical reactor network (CRN) and CFD models, validated against laboratory data, to model the impact of H 2 and inform the experimental efforts accomplished by SwRI and Solar. Ultimately, both the CRN and CFD models yielded generally good agreement with the experimental data below a particular temperature threshold. Atmospheric tests of a full-scale T130 annular combustor were performed at SwRI facilities in San Antonio, Texas, to investigate the use of H 2 addition. For these tests, the T130 combustion system remained largely unchanged; minor modifications were performed to the fuel ducting to allow for the safe use of H 2 . The test ultimately demonstrated that the addition of H 2 to the fuel mixture significantly increased the AFR ratio at which the combustor could operate. This improvement to the LBO limit should allow for less use of compressor bleed and less throttling needed by the inlet guide vanes (IGV). This in turn could result in more efficient operation of the gas turbine at lower load points. The second modification explored in this work was a direct modification to the T130 injector. The project team hypothesized that modifications to the pilot of the T130 injector could provide lower emissions at high turn-down operations. These modifications were manufactured and explored by the team at Solar. High pressure rig tests, originally slated to occur at SwRI, were ultimately accomplished by Solar to maintain overall project budget and mitigate cost growth attributable to supply chain issues and inflation. The pressurized rig tests ultimately showed that the SwRI Project No. 18.24153 - DE-EE0008415 Page 2 Final Technical Report January 24, 2024 modifications did not significantly alter the performance of the combustion system at the high turn-down conditions; both the modified injectors and the baseline configuration exhibited elevated emissions comparted to the full-load operating condition. A final set of studies performed by EPRI investigated the benefit-cost of flexible CHP as well as a grid interconnection study for the California Independent System Operator (CAISO) grid. These studies considered: traditional CHP with no spinning reserve available for on-demand grid support, 50% flexible CHP where 50% of the machine’s capacity is consumed by on-site baseload operations while providing an additional 50% capacity for on-demand grid support, and 70% flexible CHP where 70% of capacity is consumed on-site by baseload operations and 30% is available for on-demand grid support. In all cases, the analyses showed a benefit-to-cost ratio greater than unity implying a positive net present value for all configurations. However, the traditional CHP showed the most economic benefit. These results are sensitive to several factors, many of which are not fully known and may vary over time. Thus site owners must be convinced that taking up the increased costs and risks from flexible CHP would be worth implementing. As the grid in California and across the country transition to incorporate larger renewable energy generation, flexible CHP can provide much needed operating reserves and dispatchability. Alternative fuel options, such as hydrogen blending and biofuels, may also lower carbon intensities of CHP. Flexible CHP should be examined in the evolving market to understand innovative business models, changes market rules and services, and new technologies.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Experimental Study of Instabilities in Hydrogen-Air Fueled Rotating Detonation Combustion Presentation

Conventional gas turbine engines rely on an idealized constant pressure combustion process that in reality produces a pressure decrease as a result of viscous and other non-reversible losses. An alternative approach is rotating detonation combustion (RDC) which is a form of pressure gain combustion in which one or more detonation waves propagate an annular channel resulting in an increase in pressure across, subsequently providing greater work availability compared to deflagration ultimately leading to opportunities for greater thermodynamic efficiency when used in gas turbine engines that conventionally relies on constant. Modern gas turbine engines often rely on pre-mixed reactants to limit NOx emissions, although this may result in greater susceptibility to instabilities such as flashback and thermoacoustic oscillation, particularly for applications that utilize hydrogen as the fuel. Research in RDC has focused on non-premixed reactants thus limiting the occurrence of flashback, and high frequency detonation wave propagation (kHz) may interfere with the occurrence of thermoacoustic oscillations. Thermal NOx emissions are controlled through rapid combustion and sudden expansion of the working fluid. Although RDC may not be susceptible to instabilities encountered in conventional state of the art gas turbine engine combustion, there may be other mechanisms occurring that support instabilities that could be detrimental to performance.

Weber, Justin↗
DOE OSTI2025

Rapid Oxidation of Uranium Steel Alloys: Combustion Synthesis

This project explored the use of combustion synthesis as a rapid, high-temperature method for oxidizing uranium-bearing steel alloys. Traditional laboratory-scale synthesis methods often fail to replicate the thermal and kinetic conditions experienced by real-world particulates, particularly those formed under rapid quenching or high-temperature scenarios. Combustion synthesis offers a promising alternative by enabling fast, localized heating and flexible precursor selection. A series of targeted experiments were conducted using a U 2 NiCrFe 4 alloy as the precursor. The alloy was oxidized using combustion synthesis reactions fueled by uranyl nitrate and glycine, achieving peak temperatures exceeding 1,200 °C. Postreaction analysis using scanning electron microscopy (SEM), elemental mapping, and Raman spectroscopy revealed the formation of iron-based oxides, with limited but detectable evidence of uranium oxide phases such as UO 2 . The results indicate that under the rapid reaction and cooling conditions of combustion synthesis, iron oxides form preferentially, but uranium oxide formation is kinetically limited. These findings validate combustion synthesis as a viable method for simulating the oxidation behavior of uranium steels in extreme environments and lay the groundwork for future studies aimed at enhancing uranium oxide formation through higher temperatures or modified precursor compositions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Numerical Investigation of the characteristics of pressurized biomass-oxy-combustion

As a second generation of oxy-fuel combustion technologies, pressurized oxy-combustion has a potential to improve the process efficiency and economy. With the modern decarbonization needs, biomass combustion is considered to be nearly CO2 neutral, and thus co-firing biomass with coal in an oxy-combustion process can achieve a negative CO2 balance. The size of the biomass fuel particles is a key parameter in an entrained flow combustor because large biomass particles, exceeding some threshold size, may only partially be burnt due to the restrictions on the heat transport, thereby diminishing the combustion efficiency. While such a threshold particle size has been scrutinized at an atmospheric pressure, the present study extends the analysis to elevated pressures. Specifically, two scenarios were set up, for experimental-scale and full-scale pressurized oxy-combustors, with the threshold sizes of biomass particles appearing 0.5 mm and 5 mm, respectively, without temperature gradient in biomass particles. With temperature gradient, the parametric study included the particles in the range from 0.15 mm to 5 mm. It is shown that the thermal-thin model is applicable to spherical biomass particles not exceeding 0.15 mm. The impact of the heating rate on biomass particle devolatilization was also investigated and the biomass devolatilization could happen in less than 1 second; the same amount of heat energy could induce different volatile release rates.

Li, Lei↗
DOE OSTI2019

Study of Parasitic Combustion in an Optically Accessible Continuous Wave Rotating Detonation Engine

In this work we use cinematographic OH* chemiluminescence and double pass shadow- graph imaging to study non-ideal combustion phenomena in an optically accessible con- tinuous wave race-track-shaped rotating detonation engine and link them to the observed reduction in detonation properties. The study identifies and emphasizes three key non- ideal features of practical RDE operation: (1) a buffer region between post-detonation gases of the previous cycle and fresh mixture; (2) parasitic combustion upstream of the detonation wave due to premature ignition of the fresh mixture, which effectively vitiates the fresh mixture and reduces the heat release available to support the wave; and (3) what we term commensal combustion downstream of the detonation wave supported by mixture or heat release leakage through the detonation wave, which also reduces support to the wave. An evaluation of the effects of vitiation induced by parasitic combustion on detona- tion wave properties suggests that the reduction in wave speed and pressure ratio observed in experiments is consistent with the existence of such non-ideal combustion phenomena

Chacon, Fabian↗
DOE OSTI2024

A Comparative Experimental Analysis of Natural Gas Dual Fuel Combustion Ignited by Diesel and Poly OxyMethylene Dimethyl Ether

Dual-fuel low-temperature combustion is a possible solution for alleviating the tradeoff between oxides of nitrogen and soot emissions in conventional diesel combustion, albeit with poor combustion stability, high carbon monoxide, and unburned hydrocarbon emissions at low engine loads. The present work compares emissions and combustion (heat release and other metrics) of both diesel and poly-oxy methylene dimethyl ether as high-reactivity fuels to ignite natural gas while leveraging spray-targeted reactivity stratification, which involved multiple injections of the high-reactivity fuels. The experiments included six parametric sweeps of: (1) start of first injection, (2) start of second injection, (3) percentage of energy substitution of natural gas, (4) commanded injection duration ratio, (5) rail pressure, and (6) intake pressure. The experiments were performed on a 1.8 L heavy-duty single-cylinder research engine operating at a medium speed of 1339 rev/min. Not-to-exceed limits for the indicated oxides of nitrogen emissions, maximum pressure rise rate, and the coefficient of variation of the indicated mean effective pressure were set to 1 g/kWh, 10 bar/CAD, and 10%, respectively. The indicated emissions decreased and combustion improved significantly for both fueling combinations when the experimental procedure was applied.

Partridge, Kendyl Ryan↗
DOE OSTI2016

Leaner Lifted-Flame Combustion Enabled by the Use of an Oxygenated Fuel in an Optical CI Engine

Leaner lifted-flame combustion (LLFC) is a mixing-controlled combustion strategy for compression-ignition engines that does not produce soot because the equivalence ratio at the lift-off length, Φ(H), is less than or equal to approximately two. In addition to preventing soot formation, LLFC can simultaneously control emissions of nitrogen oxides because it is tolerant to the use of exhaust-gas recirculation for lowering in-cylinder temperatures. LLFC can be achieved through the use of oxygenated fuels and enhanced fuel/charge-gas mixing upstream of the lift-off length. Enhanced mixing can be obtained via higher injection pressures, smaller injector orifice diameters, lower intake-manifold and coolant temperatures, and/or more retarded injection timings. This study focuses on the effects of an oxygenated fuel blend (T50) made up of 50% by volume tri-propylene glycol mono-methyl ether with a #2 ULSD emissions-certification fuel (CFA), compared against baseline testing of the CFA fuel without the oxygenate. Experimental measurements include crank-angle resolved natural luminosity (NL) and chemiluminescence (CL) imaging diagnostics. EGR is simulated by adding nitrogen and carbon dioxide to the intake charge to produce a 16% intake-oxygen mole fraction (XO2), and results are compared against cases with no charge dilution (i.e., 21% XO2). Initial experiments with a two-hole tip achieved soot-free LLFC at low loads with the T50 fuel, 240 MPa injection pressure, 50 °C intake-manifold temperature (IMT), 95 °C coolant temperature, and -5 crank-angle degree (CAD) after top-dead-center (ATDC) start of combustion (SOC) timing. The strategy was extended to more moderate loads by employing a 6-hole injector tip, where lowering the IMT to 30 °C, reducing the coolant temperature to 85 °C, and retarding the SOC timing to +5 CAD ATDC resulted in sustained LLFC at both 21% and 16% XO2 at up to 6.2 bar gross indicated mean effective pressure (gIMEP) with T50. The achievement of LLFC was confirmed by independent soot measurements using a smoke meter, spatially integrated natural luminosity from the NL diagnostics, and laser-induced incandescence for measuring soot volume fraction in the exhaust stream. In contrast to the results with T50, LLFC was not achieved under any of the test conditions with CFA. Combustion was stable under LLFC conditions, with a coefficient of variation of gIMEP less than 1.5%. Nitrogen oxides and hydrocarbon emissions were also lowered by up to 25% each for LLFC with T50 relative to using the same operating conditions with CFA. Combustion noise was similarly reduced by 4-6 dBA, and ringing intensity by 60-80%, for LLFC with T50.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Lean-Stratified Combustion System with Miller Cycle for Downsized Boosted Application - Part I

Automotive manufacturers relentlessly explore engine technology combinations to achieve reduced fuel consumption under continued regulatory, societal and economic pressures. For example, technologies enabling advanced combustion modes, increased expansion to effective compression ratio, and reduced parasitics continue to be developed and integrated within conventional and hybrid propulsion strategies across the industry. A high-efficiency gasoline engine capable for use in conventional or hybrid electric vehicle platforms is highly desirable. This paper is the first to two papers describing the development of a combustion system combining lean-stratified combustion with Miller cycle for downsized boosted applications. The work was completed under a multi-year US DOE project. The goal was to define a light-duty engine package capable of achieving a 35% fuel economy improvement at US Tier 3 emission standards over a naturally aspirated stoichiometric baseline vehicle. A multi-mode combustion system was developed enabling highly efficient lean-stratified operation at light-load and stoichiometric Miller-cycle operation at mid- to highloads. Some of the unique challenges in synergistically combining the two concepts are highlighted in this paper. Here, a central direct-injection four-valve layout was designed with high-tumble ports and a bowl-in-piston capable of stable operation under highly dilute (lean plus EGR) mixtures when properly matched to fuel spray characteristics, a multiple-injection strategy, and a high-energy ignition system. Other challenges specific to meeting exhaust emissions requirements with a high-efficiency engine are also explored in this study. In this Part 1 of the paper, the single-cylinder combustion system design, analysis, and testing is described. Multicylinder engine system design, analysis and development is described in Part 2 of the paper.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Dilute Combustion Control Using Spiking Neural Networks

Dilute combustion with exhaust gas recirculation (EGR) in spark-ignition engines presents a cost-effective method for achieving higher levels of engine efficiency. At high levels of EGR, however, cycle-to-cycle variability (CCV) of the combustion process is exacerbated by sporadic occurrences of misfires and partial burns. Previous studies have shown that temporal deterministic patterns emerge at such conditions and certain combustion cycles have a significant influence over future events. Due to the complexity of the combustion process and the nature of CCV, harnessing all the deterministic information for control purposes has remained challenging even with physics based 0-D, 1-D, and high-fidelity computational fluid dynamics (CFD) models. In this study, we present a data-driven approach to optimize the combustion process by controlling CCV adjusting the cycle-to-cycle fuel injection quantity. Readily available data from in-cylinder pressure was used to train a spiking neural network (SNN) which learns the optimal way to manage fuel injection in order to reduce CCV while maintaining acceptable levels of fuel consumption. SNNs are particularly well suited for powertrain control applications due to their ability to be deployed on FPGA-based neuromorphic hardware which are small, inexpensive, and have a low power demand. The high-performance computing (HPC) resources of Oak Ridge National Laboratory were used to run an evolutionary-based training approach for choosing the best SNN configuration that minimizes the size of the network while achieving the desired goal. The neuromorphic hardware with the optimized SNN deployed was connected to the rapid prototyping engine control system for real-time control implementation and tested on a single cylinder version of a GM LNF 4-cylinder engine. The results show a significant reduction of CCV with a small percentage of additional fuel used to stabilize the charge.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2018

Atmospheric processing of iron in mineral and combustion aerosols: development of an intermediate-complexity mechanism suitable for Earth system models

Abstract. Atmospheric processing of iron in dust and combustion aerosols is simulated using an intermediate-complexity soluble iron mechanism designed for Earth system models. The solubilization mechanism includes both a dependence on aerosol water pH and in-cloud oxalic acid. The simulations of size-resolved total, soluble and fractional iron solubility indicate that this mechanism captures many but not all of the features seen from cruise observations of labile iron. The primary objective was to determine the extent to which our solubility scheme could adequately match observations of fractional iron solubility. We define a semi-quantitative metric as the model mean at points with observations divided by the observational mean (MMO). The model is in reasonable agreement with observations of fractional iron solubility with an MMO of 0.86. Several sensitivity studies are performed to ascertain the degree of complexity needed to match observations; including the oxalic acid enhancement is necessary, while different parameterizations for calculating model oxalate concentrations are less important. The percent change in soluble iron deposition between the reference case (REF) and the simulation with acidic processing alone is 63.8 %, which is consistent with previous studies. Upon deposition to global oceans, global mean combustion iron solubility to total fractional iron solubility is 8.2 %; however, the contribution of fractional iron solubility from combustion sources to ocean basins below 15∘ S is approximately 50 %. We conclude that, in many remote ocean regions, sources of iron from combustion and dust aerosols are equally important. Our estimates of changes in deposition of soluble iron to the ocean since preindustrial climate conditions suggest roughly a doubling due to a combination of higher dust and combustion iron emissions along with more efficient atmospheric processing.

Scanza, Rachel A.↗
NASA NTRS1970

Thermodynamics of the internal combustion engine

The ubiquitous automobile has played both the role of hero and villain during the course of its history. At the present time it is being cast as the villain with increasing frequency because it has been indicted as a major source of air pollution. It is just this characterization that is responsible for our renewed interest in the automobile. When we speak of the automobile as a source of air pollution, we really mean the heart of the automobile, the internal combustion engine. The prototype of the modern internal combustion engine was first successfully operated by Nicholas August Otto in 1876. In spite of its long history, the internal combustion engine is still poorly understood in terms of the details of the physical processes that take place during its operations. The internal combustion engine operates on what is known as the Otto cycle, and Otto cycle calculations have been with us for many years. The emphasis in earlier calculations was usually on the performance rather than on the pollution aspects. Performance characteristics can often be estimated reasonably accurately even with a considerable degree of simplification. We are interested in the pollution aspects of the internal combustion engine, and therefore the calculations must be performed with more care. Our extensive experience with equilibrium calculations places us in a position to carry out such careful calculations. We have just recently begun such an analysis, and its objective is the prediction of exhaust gas properties. I will describe our progress by first reviewing the Otto cycle, and then I will illustrate the effect of various assumptions on the calculated results.

Frank J. Zeleznik↗
NASA NTRS1972

High-pressure liquid-monopropellant strand combustion.

Examination of the influence of dissolved gases on the state of the liquid surface during high-pressure liquid-monopropellant combustion through the use of a strand burning experiment. Liquid surface temperatures were measured, using fine-wire thermocouples, during the strand combustion of ethyl nitrate, normal propyl nitrate, and propylene glycol dinitrate at pressures up to 81 atm. These measurements were compared with the predictions of a variable-property gas-phase analysis assuming an infinite activation energy for the decomposition reaction. The state of the liquid surface was estimated using a conventional low-pressure phase equilibrium model, as well as a high-pressure version that considered the presence of dissolved combustion-product gases in the liquid phase. The high-pressure model was found to give a superior prediction of measured liquid surface temperatures. Computed total pressures required for the surface to reach its critical mixing point during strand combustion were found to be in the range from 2.15 to 4.62 times the critical pressure of the pure propellant. Computed dissolved gas concentrations at the liquid surface were in the range from 35 to 50% near the critical combustion condition.

Faeth, G. M.↗
NASA NTRS1973

Mixing-controlled supersonic combustion.

The technology of supersonic combustion and its practical significance for hypersonic flight are reviewed. It is shown that this technology makes possible a good qualitative and quantitative understanding of the physical phenomena related to the process of supersonic combustion. Some of the more important, summarized aspects of this technology include the physical description of the supersonic combustion flame, the chemical reaction rates and the diffusion process involved, the interaction between combustion and fluid dynamics, and the mathematical methods of supersonic combustion analysis.

Ferri, A.↗