Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Best”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32

Simulation of spaceborne stereo radar imagery - Experimental results

Computer simulation of radar imagery was used to investigate spaceborne stereo radar. The major conclusions reached are that stereo pairs representing different angles of incidence with the same look-direction appear best and that the angles of incidence and stereo intersection angle be matched to the slope and relief of terrain. A parametric tradeoff analysis was performed for eleven different angles of incidence over three different model areas. The eleven angles spanned the range from small- to large-incidence angles. The three model areas were selected as typical of relatively flat, moderately rough, and mountainous terrain. The stereo pair judged best for each model area are included.

Kaupp, V. H.↗

Wing extensions for improving climb performance

Recent wind tunnel studies have shown that significant improvements in wing efficiency and climb performance can be achieved using wing extensions having sharp edges and unmodified upper airfoil contours. Based on tests of six configurations, a simple tip shape provided the best wing efficiency at high lift conditions without penalty during cruise conditions. The best configuration tested exhibited more than 20 percent improvement in the maximum rate of climb, plus a reduction in stall speed and a slight improvement in cruise performance over a baseline tip with a round edge. In addition to measurements that were used to determine performance, flow visualization studies provided insight into reasons for improved wing efficiency. Tests were conducted using a high performance general aviation aircraft model with a tapered, cantilevered wing.

Nicks, O. W.↗

Electron collisional rate coefficients for low-level transitions in hydrogen

There exists presently no general agreement concerning the collisional excitation rates of atomic hydrogen. The present investigation is concerned with the results reported by various investigators, taking into account the semiempirical rates of Johnson (1972), a study conducted by Aggarwal (1983), empirically based rates of Crandall et al. (1974), and the rates tabulated in Osterbrock (1974), based on the close-coupling calculations of Burke et al. (1967). It is found that there is a major conflict between the 'best' theoretical and Johnson values on the one hand, and the empirical data on the other. A study of the data shows that the Johnson value for the 1 to 2 rate agrees well with other theoretical calculations, and within 25 percent of empirical measurements, but that the Johnson 1 to 3 rate is 40-75 percent of the 'best' theoretical calculations.

Drake, S. A.↗

Effects of vegetation canopy on the radar backscattering coefficient

Airborne L- and C-band scatterometer data, taken over both vegetation-covered and bare fields, were systematically analyzed and theoretically reproduced, using a recently developed model for calculating radar backscattering coefficients of rough soil surfaces. The results show that the model can reproduce the observed angular variations of radar backscattering coefficient quite well via a least-squares fit method. Best fits to the data provide estimates of the statistical properties of the surface roughness, which is characterized by two parameters: the standard deviation of surface height, and the surface correlation length. In addition, the processes of vegetation attenuation and volume scattering require two canopy parameters, the canopy optical thickness and a volume scattering factor. Canopy parameter values for individual vegetation types, including alfalfa, milo and corn, were also determined from the best-fit results. The uncertainties in the scatterometer data were also explored.

Mo, T.↗

A SEASAT SASS simulation experiment to quantify the errors related to a + or - 3 hour intermittent assimilation technique

A series of SEASAT repeat orbits over a sequence of best Low center positions is simulated by using the Seatrak satellite calculator. These Low centers are, upon appropriate interpolation to hourly positions, Located at various times during the + or - 3 hour assimilation cycle. Error analysis for a sample of best cyclone center positions taken from the Atlantic and Pacific oceans reveals a minimum average error of 1.1 deg of Longitude and a standard deviation of 0.9 deg of Longitude. The magnitude of the average error seems to suggest that by utilizing the + or - 3 hour window in the assimilation cycle, the quality of the SASS data is degraded to the Level of the background. A further consequence of this assimilation scheme is the effect which is manifested as a result of the blending of two or more more juxtaposed vector winds, generally possessing different properties (vector quantity and time). The outcome of this is to reduce gradients in the wind field and to deform isobaric and frontal patterns of the intial field.

Sylvester, W. B.↗

Temperature dependence of elastic and strength properties of T300/5208 graphite-epoxy

Experimental results are presented for the elastic and strength properties of T300/5208 graphite-epoxy at room temperature, 116K (-250 F), and 394K (+250 F). Results are presented for unidirectional 0, 90, and 45 degree laminates, and + or - 30, + or - 45, and + or - 60 degree angle-ply laminates. The stress-strain behavior of the 0 and 90 degree laminates is essentially linear for all three temperatures and that the stress-strain behavior of all other laminates is linear at 116K. A second-order curve provides the best fit for the temperature is linear at 116K. A second-order curve provides the best fit for the temperature dependence of the elastic modulus of all laminates and for the principal shear modulus. Poisson's ratio appears to vary linearly with temperature. all moduli decrease with increasing temperature except for E (sub 1) which exhibits a small increase. The strength temperature dependence is also quadratic for all laminates except the 0 degree - laminate which exhibits linear temperature dependence. In many cases the temperature dependence of properties is nearly linear.

Milkovich, S. M.↗

A Concept for the Processing and Display of Thematic Mapper Data

Multispectral information can best be accessed and evaluated through digital interactive image processing techniques. The potential user community, however, has not reached the level where image processing is being used routinely as a standard tool. Therefore, for the time being, special effort must be put into development of strategies that will guarantee optimal utilization of the spectral information contained in remote sensing data acquired under the varying conditions affecting each scene. The Thematic Mapper system provides spectral information in seven carefully selected spectral bands, covering the visible, near IR, short-wave IR and thermal IR region of the electromagntic spectrum. The challenge is to devise the best approach for presenting this complex spectral information in a pictorial format which can be understood and accepted as a standard by the growing user community.

Haydn, R.↗

Computer studies of hybrid-slotted working sections with minimum interference at subsonic speeds

A series of computations on tunnel boundary-interference effects for hybrid-slotted working sections was performed using the WALINT code. The slots were modeled as lines of porosity with linear crossflow characteristics. The basic shape evaluated was for a rectangular section with height-to-width ratio = 0.835 and its companion in the duplex mode (half model testing) with height-to-width ratio = 0.6. A best overall basic configuration was determined with seven slots on each wall with open area ratio on each wall of 17.5%. For both full-span and half-model testing, the optimum solution required closing all but two slots on each of the half-walls parallel to the plane of the wing (equivalent to four slots on the full floor and ceiling). The results are presented here for the best configurations and are shown to be within the figure-of-merit range of + or - 0.04 in upwash, and + or - 0.1 in curvature for the Mach number range 0.6 to 0.85. Blockage effects are shown to be small.

Steinle, F. W., Jr.↗

Fitting of satellite and in-situ ocean surface temperatures Results for polymode during the winter of 1977-1978

For the period considered, December 1977 through February 1978, bivariate Gaussian discriminant function cloud identification revealed that more than 93 percent of the 8-km resolution GOES infrared pixels were cloud contaminated. Cloud-free in-situ calibration points were distributed in nonrandom groups; this resulted in systematic errors when using least squares techniques. Surfaces and regression lines were least squares fitted between satellite and in-situ data; use was also made of differences and ratios. The best results were achieved with a regression in the form of the infrared radiative transfer equation; but this was no better than + or - 0.9 K. Because of extensive cloudiness, the linear regressions were seldom useful, and temperature ratios with + or - 1.3 K experimental errors best represent the applicability of GEOS data to sea surface temperatures.

Maul, G. A.↗

Theoretical study of the dipole moment of oxygen monofluoride (OF)

The ground-state potential curve and dipole-moment function of OF are calculated theoretically using the complete active-space self-consistent-field levels, externally contracted configuration-interaction levels, or multireference (singles plus doubles) configuration-interaction levels. Both an extended Gaussian basis set and a double-zeta-plus-polarization basis set were applied. The results are presented in extensive tables and graphs. Best results are achieved using a large Gaussian basis set and taking the valence-correlation energy into account. It is suggested that OF may best be detected by its laser-magnetic-resonance spectrum in the IR.

Langhoff, S. R.↗

Signalling characteristics in satellite-aided land mobile communications

The feasibility of land mobile radio communications has been demonstrated by a large number of experiments with NASA's ATS satellites. Significant differences in the propagation characteristics of satellite and terrestrial mobile signal paths were observed in the experiments. Terrestrial paths are best in cities where they can provide frequency reuse and assure communication by bouncing signals around obstructions. Satellites may be best in thinly populated areas because they eliminate the need for many tower mounted relays. The satellite paths do not have the severe Rayleigh fading that limits the range and signal quality of terrestrial paths if the satellite is above approximately ten degrees elevation, a value easily achieved for the United States. The experiments verified that high quality voice communications and other functions, such as data transmission and vehicle position surveillance, are easily accomplished through geostationary satellites with vehicle transmitter power and antenna gain no different than those of terrestrial mobile communications.

Anderson, R. E.↗

Advanced passive radiator for spaceborne cryogenic cooling

A novel design to improve the cooling capability of spaceborne cryogenic passive radiators is described. The design is based on the use of lightweight angled radiation shields, low-conductance structural supports, and a separate detachable launch-support system to reduce the parasitic heat leaks from the warm spacecraft to the cold radiator. The effectiveness of this design is demonstrated by thermal-vacuum-chamber experiments which indicate that the angled-radiation-shield assembly has an effective emittance that is an order of magnitude lower than that of the best multilayer insulation used in flight. Performance predictions based on the experiments and analytical model indicate that an advanced passive-radiator design based on this technology would be between 10 and 57% of the size and 10 and 36% of the mass of the best state-of-the-art passive radiators and would make lower temperatures (< 60 K) and larger heat loads practical. The cooling requirements of many new spaceborne instruments could be accommodated by application of this new passive-radiator design.

Steven Bard↗

The atomic geometries of GaP(110) and ZnS(110) revisited - A structural ambiguity and its resolution

The atomic geometries of GaP(110) and ZnS(110) are reexamined using the R-factor minimization procedure, developed for GaAs(110) and previously applied to GaSb(110), ZnTe(110), InAs(110), and AlP(110), to analyze experimental elastic low-energy electron diffraction intensities. Unlike most of the earlier cases, both GaP(110) and ZnS(110) exhibit two distinct minimum-Rx structures which cannot be distinguished by analysis of the shapes of the intensity profiles alone. One region of best-fit structures exhibits top-layer displacements normal to the surface characterized by a small bond-length-conserving, top-layer rotation (omega aproximately 2-3 deg), a small relaxation of the top layer away from the surface, and a 10 percent expansion of the top-layer bond length. The other region of best-fit structures is the conventional one: nearly bond-length-conserving rotations of omega = 26-28 deg in the top layer and a small (approximately 0.1 A) contraction of the uppermost layer spacing. This ambiguity may be removed, however, by consideration of the integrated beam intensities. The conventional region of structural parameters provides a decisively better description of the relative magnitudes of the integrated beam intensities and hence is the preferred structure.

Duke, C. B.↗

Optimizing Load Spectra for Gears

Life expectancy of gear systems extended. NASA document presents algorithm for gear-load-spectrum synthesis (GLSS) as aid in choosing best load spectrum for machine containing gears. Objective of GLSS: Determine best schedule or combination of load elements-one that yields longest possible fatigue life for machine.

Oyoung, S. P. P.↗

Fitting aerodynamic forces in the Laplace domain: An application of a nonlinear nongradient technique to multilevel constrained optimization

A technique which employs both linear and nonlinear methods in a multilevel optimization structure to best approximate generalized unsteady aerodynamic forces for arbitrary motion is described. Optimum selection of free parameters is made in a rational function approximation of the aerodynamic forces in the Laplace domain such that a best fit is obtained, in a least squares sense, to tabular data for purely oscillatory motion. The multilevel structure and the corresponding formulation of the objective models are presented which separate the reduction of the fit error into linear and nonlinear problems, thus enabling the use of linear methods where practical. Certain equality and inequality constraints that may be imposed are identified; a brief description of the nongradient, nonlinear optimizer which is used is given; and results which illustrate application of the method are presented.

Tiffany, S. H.↗

A study on the imaging potential of QUASAT

The orbit, ground array, and sensitivities of the space and ground systems of the QUASAT spaceborne astronomy mission were studied. Parameters which yield images in which the noise is within a factor of three of the thermal noise limit were derived. With a very large ground array QUASAT should produce images as complex as the best of the VLA. At 22 GHz the resolution will be 0.1 milliarcsec, the field of view 15 milliarcsec, and it will be possible to make noise limited maps of complex objects. The QUASAT is essential for mapping southern declination objects. Without QUASAT, even the simple core-jet source cannot be mapped at declination minus 60 deg. It will be possible with QUASAT to make maps with observing times as short as 6 hr although the very best maps will require 48 hr observations.

Readhead, A. C. S.↗

Integrated technology rotor/flight research rotor concept definition study

As part of the Integrated Technology Rotor/Flight Research Rotor (ITR/FRR) Program a number of advanced rotor system designs were conceived and investigated. From these, several were chosen that best meet the started ITR goals with emphasis on stability, reduced weight and hub drag, simplicity, low head moment stiffness, and adequate strength and fatigue life. It was concluded that obtaining low hub moment stiffness was difficult when only the blade flexibility of bearingless rotor blades is considered, unacceptably low fatigue life being the primary problem. Achieving a moderate hub moment stiffness somewhat higher than state of the art articulated rotors in production today is possible within the fatigue life constraint. Alternatively, low stiffness is possible when additional rotor elements, besides the blades themselves, provide part of the rotor flexibility. Two primary designs evolved as best meeting the general ITR requirements that presently exist. An I shaped flexbeam with an external torque tube can satisfy the general goals but would have either higher stiffness or reduced fatigue life. The elastic gimbal rotor can achieve a better combination of low stiffness and high fatigue life but would be a somewhat heavier design and possibly exhibit a higher risk of aeromechanical instability.

Carlson, R. G.↗

Solar Flare and IMF Sector Structure Effects in the Lower Ionosphere

About 1% of all sudden ionospheric disturbances (SIDs) observed at the Panska Ves Observatory (Czechoslovakia), were found to be not of solar-XUV origin. Among them, the very rare SWF events (observed at L = 2.4) of corpuscular origin are the most interesting. The IMF sector structure effects in the midlatitude lower ionosphere are minor in comparison with effects of solar flares, geomagnetic storms, etc. There are two basic types of effects. The first type is a disturbance, best developed in geomagnetic activity, and observed in the night-time ionosphere. It can be interpreted as a response to sector structure related changes of geomagnetic (= magnetospheric) activity. The other type is best developed in the tropospheric vorticity area index and is also observed in the day-time ionosphere in winter. This effect is quietening in the ionosphere as well as troposphere. While the occurrence of the former type is persistent in time, the latter is severely diminished in some periods. All the stratosphere, the 10-mb level temperature and height above Berlin-Tempelhof do not display any observable IMF section structure effect.

Lastovicka, J.↗