Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Army”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
NASA NTRS1935

Bending stresses due to torsion in cantilever box beams

The paper beings with a brief discussion on the origin of the bending stresses in cantilever box beams under torsion. A critical survey of existing theory is followed by a summary of design formulas; this summary is based on the most complete solution published but omits all refinements considered unnecessary at the present state of development. Strain-gage tests made by NACA to obtained some experimental verification of the formulas are described next. Finally, the formulas are applied to a series of box beams previously static-tested by the U.S. Army Air Corps; the results show that the bending stresses due to torsion are responsible to a large extent for the free-edge type of failure frequently experienced in these tests.

Kuhn, Paul↗
NASA NTRS1933

The Aerodynamic Effect of a Retractable Landing Gear

Tests were conducted in the N.A.C.A. full scale wind tunnel at the request of the Army Air Corps to determine the effect of retractable landing gear openings in the bottom surface of a wing upon the characteristics of a Lockheed Altair airplane. The tests were extended to include the determination of the lift and drag characteristics throughout the angle-of-attack range with the landing gear both retracted and extended. Covering the wheel openings in the wing with sheet metal when the wheels were extended reduced the drag only 2 percent at a lift coefficient of 1.0, which was assumed for the take-off condition. Therefore, the wheel openings in the bottom side of the wing have a negligible effect upon the take-off of the airplane. Retracting the landing gear reduced the minimum drag of the complete airplane 50 percent.

Defrance, Smith J↗
NASA NTRS1935

Drag of Prestone and Oil Radiators on the YO-31A Airplane

At the request of the Army Air Corps tests were conducted on a mock-up of the YO-31A airplane to determine the drag of the prestone and oil radiators. The drag of the airplane was determined with both radiators exposed on the lower surface of the fuselage; with each radiator exposed; and with no radiators. The results show that at 120 m.p.h the oil radiator accounted for 2.8 percent of the drag of the complete airplane; the prestone radiator 8.3 percent; and both radiators together, 11.8 percent.

RADIATORS - DOUGLAS YO-31A - DRAG↗
NASA NTRS1934

Full-scale Drag Tests of Landing Lamps

Drag tests were conducted in the N.A.C.A. full-scale wind tunnel on full-scale models of two Army Air Corps type A-6 landing lamps mounted on an 8 by 48 foot airfoil. Drag measurements were made with the lamps in the leading edge and attached to the lower surface at the 5 and 10 percent chord positions. The drag of the lamps when faired into the airfoil was also measured. The results show that at 100 miles per hour and at the angle of minimum drag of the airfoil the unaired lamps in the leading edge produced an increase in drag of 5.5 pounds and that the unaired lamps on the lower surface at either position increased the airfoil drag 22.5 pounds. These increases represent 6 and 24 percent of the minimum drag of the airfoil, respectively. Fairing the lamps into the airfoil reduced the drag of the lamps about 50 percent for the leading-edge position and about 60 percent for the two lower surface positions.

Dearborn, C H↗
NASA NTRS1949

Lateral and Directional Stability and Control Characteristics of a C-54D Airplane

Data are presented showing compliance of C-54D with Army and Navy lateral and directional stability and control specifications. The airplane met requirements except for the rolling effectiveness pb/2V, the aileron forces in rolling, and the rudder forces in the asymmetric power conditions which were marginal. Also, the results of special tests concerning asymmetric power, asymmetric loading, and pitch due to yaw requested by the Airplane Handling Qualities Subcommittee of the Air Transport Association are presented.

AIRPLANES - SPECIFIC TYPES↗
NASA NTRS1921

Data on the Design of Plywood for Aircraft

This report makes available data which will aid the designer in determining the plywood that is best adapted to various aircraft parts. It gives the results of investigations made by the Forest Products Laboratory of the United States Forest Service at Madison, Wisconsin, for the Army and Navy Departments, and is one of a series of reports on the use of wood in aircraft prepared by the Forest Products Laboratory for publication by the National Advisory Committee for Aeronautics. The object of the study was to determine, through comprehensive tests, the mechanical and physical properties of plywood and how these properties vary with density, number, thickness, arrangement of the plies and direction of grain of the plies.

Elmendorf, Armin↗
NASA NTRS1921

Performance of a Liberty 12 airplane engine

In cooperation with the Engineering Division of the Air Service of the United States Army, a Liberty-12 engine has been tested at the Bureau of Standards. The program of tests was planned to yield that information considered most important in determining the value of the engine for aviation. Full power runs were made at the ground, at 25,000 feet, and at several intermediate altitudes. To determine the mechanical efficiency of the engine, friction horsepower was measured at the ground and at 15,000 feet. As a basis for predicting engine performance with a propeller, a series of tests was made in which the dynamometer load and engine throttle were adjusted at each speed to simulate the engine load which would be imposed at that speed by a propeller operating under normal full load at 1,700 r.p.m. Among the quantities calculated from the test measurements are: brake horsepower; break mean effective pressure; fuel consumption; mixture ratio; mechanical, thermal, and volumetric efficiency; and the percentage of the heat in the fuel appearing in the jacket water and in the exhaust. Jacket water temperature, oil temperature, manifold pressure, etc., are recorded to show the conditions under which the test was made.

Sparrow, S W↗
NASA NTRS1923

Nomenclature for Aeronautics

This nomenclature for aeronautics was prepared by a special conference on aeronautical nomenclature, composed of representatives of the Army and Navy Air Services, the Air Mail Service, the Bureau of Standards, the National Advisory Committee for Aeronautics, and private life. This report supersedes all previous publications of the committee on this subject. It is published with the intention of securing greater uniformity and accuracy in official documents of the government, and, as far as possible, in technical and other commercial publications. (author)

Source record↗
NASA NTRS1924

The Small Angular Oscillations of Airplanes in Steady Flight

This investigation was carried out by the National Advisory Committee for Aeronautics at the request of the Army Air Service to provide data concerning the small angular oscillations of several types of airplanes in steady flight under various atmospheric conditions. The data are of use in the design of bomb sights and other aircraft instruments. The method used consisted in flying the airplane steadily in one direction for at least one minute, while recording the angle of the airplane with the sun by means of a kymograph. The results show that the oscillations differ but little for airplanes of various types, but that the condition of the atmosphere is an important factor. The average angular excursion from the mean in smooth air is 0.8 degrees in pitch, 1.4 degrees in roll, and 0.9 degrees in yaw, without special instruments to aid the pilot in holding steady conditions. In bumpy air the values given above are increased about 50 per cent. (author)

Norton, F H↗
NASA NTRS1926

Inertia Factors of Ellipsoids for Use in Airship Design

This report is based on a study made by the writer as a member of the Special Committee on Design of Army Semirigid Airship RS-1 appointed by the National Advisory Committee for Aeronautics. The increasing interest in airships has made the problem of the potential flow of a fluid about an ellipsoid of considerable practical importance. In 1833 George Green, in discussing the effect of the surrounding medium upon the period of a pendulum, derived three elliptic integrals, in terms of which practically all the characteristics of this type of motion can be expressed. The theory of this type of motion is very fully given by Horace Lamb in his "Hydrodynamics," and applications to the theory of airships by many other writers. Tables of the inertia coefficients derived from these integrals are available for the most important special cases. These tables are adequate for most purposes, but occasionally it is desirable to know the values of these integrals in other cases where tabulated values are not available. For this reason it seems worth while to assemble a collection of formulae which would enable them to be computed directly from standard tables of elliptic integrals, circular and hyperbolic functions and logarithms without the need of intermediate transformations. Some of the formulae for special cases (elliptic cylinder, prolate spheroid, oblate spheroid, etc.) have been published before, but the general forms and some special cases have not been found in previous publications. (author)

Tuckerman, L. B.↗
NASA NTRS1926

Water Model Tests for Semirigid Airships

The design of complicated structures often presents problems of extreme difficulty which are frequently insoluble. In many cases, however, the solution can be obtained by tests on suitable models. These model tests are becoming so important a part of the design of new engineering structures that their theory has become a necessary part of an engineer's knowledge. For balloons and airships water models are used. These are models about 1/30 the size of the airship hung upside down and filled with water under pressure. The theory shows that the stresses in such a model are the same as in the actual airship. In the design of the Army Semirigid Airship RS-1 no satisfactory way was found to calculate the stresses in the keel due to the changing shape of the bag. For this purpose a water model with a flexible keel was built and tested. This report gives the theory of the design, construction, and testing of such a water model.

Tuckerman, L.B.↗
NASA NTRS1926

The Air Forces on a Model of the Sperry Messenger Airplane Without Propeller

This is a report on a scale effect research which was made in the variable-density wind tunnel of the National Advisory Committee for Aeronautics at the request of the Army Air Service. A 1/10 scale model of the sperry messenger airplane with USA-5 wings was tested without a propeller at various Reynolds numbers up to the full scale value. Two series of tests were: the first on the original model which was of the usual simplified construction, and the second on a modified model embodying a great amount of detail. The experimental results show that the scale effect is almost entirely confined to the drag. It was also found that the model should be geometrically similar to the full-scale airplane if the test data are to be directly applicable to full scale.

Munk, Max M↗
NASA NTRS1927

Nomenclature for Aeronautics

This nomenclature for aeronautics was prepared by a Special Conference on Aeronautical Nomenclature by the executive committee of the National Advisory Committee for Aeronautics at a meeting held on August 19, 1924, at which meeting Dr. Joseph S. Ames was appointed chairman of the conference. The conference was composed of representatives of the National Advisory Committee for Aeronautics and specially appointed representatives officially designated by the Army Air Service, the Bureau of Aeronautics of the Navy Department, the Bureau of Standards, the American Society of Mechanical Engineers, the Society of Automotive Engineers, and the Aeronautical Chamber of Commerce. The purpose of the committee in the preparation and publication of this report is to secure uniformity in the official documents of the government and, as far as possible, in technical and other commercial publications

Source record↗
NASA NTRS1927

The air forces on a systematic series of biplane and triplane cellule models

The air forces on a systematic series of biplane and triplane cellule models are the subject of this report. The test consist in the determination of the lift, drag, and moment of each individual airfoil in each cellule, mostly with the same wing section. The magnitude of the gap and of the stagger is systematically varied; not, however, the decalage, which is zero throughout the tests. Certain check tests with a second wing section make the tests more complete and conclusions more convincing. The results give evidence that the present army and navy specifications for the relative lifts of biplanes are good. They furnish material for improving such specifications for the relative lifts of triplanes. A larger number of factors can now be prescribed to take care of different cases.

Munk, Max M↗
NASA NTRS1928

Pressure Distribution over a Wing and Tail Rib of a VE-7 and of a TS Airplane in Flight

This investigation was made to determine the pressure distribution over a rib of the wing and over a rib of the horizontal tail surface of an airplane in flight and to obtain information as to the time correlation of the loads occurring on these ribs. Two airplanes, VE-7 and TS, were selected in order to obtain the information for a thin and a thick wing section. In each case the pressure distribution was recorded for the full range of angle of attack in level flight and throughout violent maneuvers. The results show: (a) that the present rib load specifications in use by the Army Air Corps and the Bureau of Aeronautics, Navy Department, are in fair agreement with the loads actually occurring in flight, but could be slightly improved; (b) that there appears to be no definite sequence in which wing and tail surface ribs reach their respective maximum loads in different maneuvers; (c) that in accelerated flight, at air speeds less than or equal to 60 per cent of the maximum speed, the accelerations measured agree very closely with the theoretically possible maximum accelerations. In maneuvers at higher air speeds the observed accelerations were smaller than those theoretically possible. (author)

Crowley, J W , Jr↗
NASA NTRS1929

Pressure Distribution Tests on PW-9 Wing Models from -18 Degree Through 90 Degree Angle of Attack

At the request of the Army Air Corps, an investigation of the pressure distribution over PW-9 wing models was conducted in the atmospheric wind tunnel of the National Advisory Committee for Aeronautics. The primary purpose of these tests was to obtain wind-tunnel data on the load distribution on the cellule to be correlated with similar information obtained in flight tests, both to be used for design purposes. Because of the importance of the conditions beyond the stall as affecting the control and stability, this investigation was extended through 90 degree angle of attack. The results for the range of normal flight have been given in NACA Technical Report No. 271. The present paper presents the same results in a different form and includes, in addition, those over the greater range of angle of attack, -18 degrees through 90 degrees. The results show that: (1) at angles of attack above maximum lift, the biplane upper wing pressures are decreased by the shielding action of the lower wing. (2) the burble of the biplane lower wing, with respect to the angle of attack, is delayed, due to the shielding action of the lower wing. (3) the center of pressure of the biplane upper wing (semispan) is, in general, displaced forward and outward with reference to that of the wing as a monoplane, while for the lower wing there is but slight difference for both conditions. (4) the overhanging portion of the upper wing is little affected by the presence of the lower wing.

Loeser, Oscar E , Jr↗
NASA NTRS1929

An Investigation of the Aerodynamic Characteristics of an Airplane Equipped with Several Different Sets of Wings

This investigation was conducted by the National Advisory Committee for Aeronautics at Langley Field, Va., at the request of the Army Air Corps, for the purpose of comparing the full scale lift and drag characteristics of an airplane equipped with several sets of wings of commonly used airfoil sections. A Sperry Messenger Airplane with wings of R.A.F.-15, U.S.A.-5, U.S.A.-27, and Gottingen 387 airfoil sections was flown and the lift and drag characteristics of the airplane with each set of wings were determined by means of glide tests. The results are presented in tabular and curve form. (author)

Crowley, J W , Jr↗
NASA NTRS1930

Aerodynamic Characteristics of Twenty-Four Airfoils at High Speeds

The aerodynamic characteristics of 24 airfoils are given for speeds of 0.5, 0.65, 0.8, 0.95, and 1.08 times the speed of sound, as measured in an open-jet air stream 2 inches in diameter, using models of 1-inch chord. The 24 airfoils belong to four general groups. The first is the standard R. A. F. family in general use by the Army and Navy for propeller design, the members of the family differing only in thickness. This family is represented by nine members ranging in thickness from 0.04 to 0.20 inch. The second group consists of five members of the Clark Y family, the members of the family again differing only in thickness. The third group, comprising six members, is a second R. A. F. Family in which the position of the maximum ordinate is varied. Combined with two members of the first R.A.F. family, this group represents a variation of maximum ordinate position from 30 to 60 percent of the chord in two camber ratios, 0.08 and 0.16. The fourth group consists of three geometrical forms, a flat plate, a wedge, and a segment of a right circular cylinder. In addition one section used in the reed metal propeller was included. These measurements form a part of a general program outlined at a Conference on Propeller Research organized by the National Advisory Committee for Aeronautics and the work was carried out with the financial assistance of the committee (author)

Brigg, L J↗