Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “voltage stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Stability of Cu(In x Ga 1− x )Se 2 Solar Cells Utilizing RbF Postdeposition Treatment under a Sulfur Atmosphere

Alkali halide postdeposition treatments (PDTs) have become a key tool to maximize efficiency in Cu(In x Ga 1− x )Se 2 (CIGS) photovoltaics. RbF PDTs have emerged as an alternative to the more common Na‐ and K‐based techniques. This study utilizes temperature‐dependent current–voltage ( JVT ) measurements to study a unique RbF PDT performed in a S atmosphere. The samples are measured before and after 6 months in a desiccator to study device stability. Both samples contain Na and K which diffuse from the soda–lime glass substrate. A reference sample and a RbF + S PDT sample both show the development of a rear contact barrier after aging. The contact barrier is higher for the RbF + S PDT sample, leading to decreased current in forward bias. Series resistance is also higher in the RbF + S PDT device which leads to lower fill factor. However, after aging the reference sample has a larger decrease in open‐circuit voltage ( V OC ). Ideality factor measurements suggest Shockley–Read–Hall recombination dominates both samples. V OC versus temperature and a temperature‐dependent activation energy model are used to calculate diode activation energies for each sample condition. Both techniques produce similar values that indicate recombination primarily occurs within the bulk absorber.

14 SOLAR ENERGY↗
DOE OSTI2020

A new halospinel superionic conductor for high-voltage all solid state lithium batteries

We report a new Li-superionic chloride, Li 2 Sc 2/3 Cl 4 , that crystallizes in a disordered spinel structure, and exhibits an ionic conductivity of 1.5 mS cm –1 with a low activation energy barrier for Li + ion diffusion of 0.34 eV. Here, this material is the first spinel-type superionic halide. Structural elucidation via powder neutron diffraction reveals a significantly disordered Li + -ion distribution over available tetrahedral and octahedral sites within the lattice, forming an infinitely 3D connected Li + ion diffusion pathway comprised of face-sharing octahedra and tetrahedra. Due to the high oxidative stability of Li 2 Sc 2/3 Cl 4 , all solid state lithium batteries employing Li 2 Sc 2/3 Cl 4 and high voltage cathodes (LiCoO 2 , LiNi 0.6 Mn 0.2 Co 0.2 O 2 or high-Ni LiNi 0.85 Mn 0.1 Co 0.05 O 2 ) – without any coating – exhibit excellent electrochemical performance up to 4.6 V in terms of capacity retention and cycle life.

25 ENERGY STORAGE↗
DOE OSTI2025

Explainable artificial intelligence relates perovskite luminescence images to current-voltage metrics

As the demand for low-cost, high-efficiency solar energy technologies grows, metal halide perovskite (MHP) solar cells have emerged as a promising candidate for next-generation photovoltaics due to their high power conversion efficiencies. However, their poor durability and issues with manufacturing consistency remain significant barriers to commercialization. In this work, we develop deep learning models to support materials characterization and provide insight into features and processes influencing performance. The models are trained using transfer learning of a pretrained model to predict relevant current-voltage (IV) metrics based on different combinations of input electroluminescence (EL) and photoluminescence (PL) images of MHP devices. We examine which image types are most informative in accurately predicting different IV metrics. Additionally, we use explainable artificial intelligence (XAI) techniques to provide insights into specific spatial features in the devices that drive differences in performance. We find that stabilized luminescence images (e.g. those collected after biasing the devices for at least 1 min) are better for predicting metrics of open-circuit voltage (by PL) and short-circuit current (by PL with EL), but that predicting fill factor and overall power output may use the time-evolution of EL images. Based on attribution masks generated by integrated gradients for each device performance metric, we further suggest different loss mechanisms associated with categories of large and small spatial defects. Overall, this case study highlights the potential applicability of XAI methodology for streamlining MHP device analysis and accelerating detailed understanding of the relationships between spatial defects and impacts on performance.

14 SOLAR ENERGY↗
DOE OSTI2023

Solution–Doped Donor–Acceptor Copolymers Based on Diketopyrrolopyrrole and 3, 3'–Bis (2–(2–(2–Methoxyethoxy) Ethoxy) ethoxy)–2, 2'–Bithiophene Exhibiting Outstanding Thermoelectric Power Factors with p –Dopants

The design of polymeric semiconductors exhibiting high electrical conductivity (σ) and thermoelectric power factor (PF) will be vital for flexible large-area electronics. In this work, four polymers based on diketopyrrolopyrrole (DPP), 2,3-dihydrothieno[3,4-b][1,4]dioxine (EDOT), thieno[3,2-b]thiophene (TT), and 3, 3'-bis (2-(2-(2-methoxyethoxy) ethoxy) ethoxy)-2, 2'-bithiophene (MEET) are investigated as side-chains, with the MEET polymers newly synthesized for this study. These polymers are systematically doped with tetrafluorotetracyanoquinodimethane ( F 4 TCNQ), CF3SO3H, and the synthesized dopant Cp(CN) 3 -(COOMe) 3 , differing in geometry and electron affinity. The DPP-EDOT-based polymer containing MEET as side-chains exhibits the highest conductivity (σ) ≈700 S cm–1 in this series with the acidic dopant (CF 3 SO 3 H). This polymer also shows the lowest oxidation potential by cyclic voltammetry (CV), the strongest intermolecular interactions evidenced by differential scanning calorimetry (DSC), and has the most oxygen-based functionality for possible hydrogen bonding and ionic screening. Other polymers exhibit high σ ≈300–500 S cm–1 and power factor up to 300 µW m –1 K –2 . The mechanism of conductivity is predominantly electronic, as validated by time-dependent conductance studies and transient thermo voltage monitoring over time, including for those doped with the acid. Furthermore, these materials maintain significant thermal stability and air stability over ≈6 weeks. Density functional theory calculations reveal molecular geometries and inform about frontier energy levels. Raman spectroscopy, in conjunction with scanning electron microscopy (SEM-EDS) and x-ray diffraction, provides insight into the solid-state microstructure and degree of phase separation of the doped polymer films. Infrared spectroscopy enables this study to further quantify the degree of charge transfer from polymer to dopant.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Initial tests of large format sensors for the ATLAS ITk strip tracker

For the construction of the Inner Tracker (ITk) as part of the phase-II upgrade programme of the ATLAS detector for the High-Luminosity (HL) LHC, batches of Long Strip (LS) and Short Strip (SS) n + -in-p type micro-strip sensors have been produced by Hamamatsu Photonics and Infineon. The full size sensors measure approximately 98 × 98 mm 2 and are designed and engineered for tolerance against the 9.7 × 10 14 1 MeV n eq /cm 2 fluence expected at the HL-LHC, including a safety factor of 1.5. Each sensor has 2 or 4 columns of 1280 individual channels arranged at 75.5 μ m horizontal pitch. To ensure the sensors comply with their specifications, a Quality Control (QC) procedure has been implemented, comprising measurements on every individual sensor as well as on a sample basis. Every sensor is subjected to an initial visual inspection, after which the full surface of the sensor is captured with very high resolution by an automated camera setup. Non-contact metrology is performed to obtain the sensor surface profile. Electrical measurements establishing the reverse bias leakage current and depletion voltage are then conducted automatically. Sample sensors from every batch are subjected to 40 h of leakage stability checks in controlled atmosphere, and tests on every channel measuring leakage current, coupling capacitance and bias resistance are done. The recorded results are uploaded to a production database following data quality checks. In this paper, QC test validation data and the compiled results for the first batches of production grade sensors are presented. The QC protocol was validated, and the first production sensors were confirmed to be within specification. The results are compared to those from the previous generation of prototype sensors.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Tandem Mass-Selective Cryogenic Digital Ion Traps for Enhanced Cluster Formation

We present the implementation of tandem mass-selective cryogenic ion traps, designed to enhance the range of ion processing capabilities that can be performed prior to spectroscopic interrogation. We show that both the formation of ion clusters and mass filtering steps can be combined in a single cryogenic linear quadrupole ion trap driven by RF square waves. Mass filtering and mass isolation can be achieved by manipulation of the RF frequency and duty cycle. Very importantly, this scheme circumvents the need for high-amplitude RF voltages that can be incompatible with typical cryogenic ion processing conditions. In addition, proper adjustment of the stability boundaries during the clustering process allows for the preferential formation of a specific cluster size rather than a broad distribution of sizes. Lastly, we show that a specific cluster size can be formed, mass-selected, and then transferred to another ion trap for a second completely separate ion processing step. Furthermore, the instrumentation and modular design developed here expand the scope of ionic species and clusters that can be accessed by processing electrosprayed ions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Membrane Pretreatment and Cell Conditioning for Proton Exchange Membrane Water Electrolysis

As the research community studying proton exchange membrane water electrolysis (PEMWE) grows, it is important to develop methods that achieve transparent, reproducible research. Reproducibility of performance and durability is a challenge facing the PEMWE field, as the published literature includes a wide spread of results obtained with nominally similar materials. Prior round-robin performance benchmarking efforts [1] have identified inadequate cell conditioning as a major source of variation in apparent cell performance. Inadequate pre-treatment and conditioning can lead to instability in initial performance and adds ambiguity to durability measurements. However, excessively prolonged conditioning procedures limit the throughput of testing and the pace of research. Pretreatment and conditioning methods vary significantly across the research literature, but little systematic investigation is available into the mechanisms of these procedures or how procedural differences may impact results. This presentation will discuss investigations into the effects of membrane pre-treatment and operating procedures during cell conditioning on initial performance and catalyst-specific accelerated stress tests, with the aim of recommending procedures to enable clear, reproducible, and high-throughput research. Methods investigated include the use of hydrogen peroxide, acids, and hydration at elevated temperature for membrane pretreatment, and conditioning procedures such as current or voltage holds and cycling. The investigations cover both the impacts of these procedures on cell performance and stability as well as underlying mechanisms and processes taking place in the cell materials.

cell↗
DOE OSTI2025

Insight Into Sulfur‐Containing Additive to Boost Anti‐Oxidation Ability of the Ether‐Based Electrolyte for Sodium‐Ion Full Batteries

Ether-based electrolytes are considered as promising candidates for sodium-ion batteries (SIBs) due to their high ionic conductivity and good compatibility with hard carbon (HC) anode. However, they suffer from poor anti-oxidative ability with unstable cathode electrolyte interface, inducing successive electrolyte decomposition and rapid capacity fading. Herein, the sulfur-containing additive (1,3-propanediol cyclic sulfate, PCS) is introduced to boost the stability of the electrode-electrolyte interface (EEI) in ether-based electrolyte. PCS largely participates in the inner Na + sheath, causing more diglyme (G2) molecules and fewer PF 6 - anions to occupy the inner Na + solvation sheath, avoiding the decomposition of G2 molecules at high operation voltage. Moreover, PCS is beneficial for simultaneously constructing thin and robust sulfur-containing EEI on both Prussian blue (PB) cathode and HC anode, maintaining the structural stability of PB and alleviating the dissolution of transition metals. These enable PB||HC pouch cells to deliver a capacity retention of 60.3% after 400 cycles, significantly higher than the 32.1% in PCS-free electrolytes. In conclusion, this work discloses the underlying mechanism of PCS to evoke the anti-oxidation ability of ether-based electrolyte and provides a promising method for realizing advanced sodium-ion full cells.

anti-oxidation ability↗
DOE OSTI2020

New Synthesis Strategies to Improve Co-Free LiNi0.5Mn0.5O2 Cathodes: Early Transition Metal d0 Dopants and Manganese Pyrophosphate Coating

In this work, we report solution-based doping and coating strategies to improve the electrochemical performance of the Co-free layered oxide cathode LiNi0.5Mn0.5O2 (LNMO). Small amounts of d0 dopants (e.g., Mo6+and Ti4+, 0.5-1 at. %) increase the cathode’s specific capacity, cycling stability, and rate capability. More specifically, a Mo-doped cathode with the nominal composition LiNi0.495Mn0.495Mo0.01O2 achieves a high reversible capacity of 180 mAh/g at 20 mA/g with good retention at higher rates (e.g., 120 mAh/g at 100 mA/g). Effects of 1 at.% Mo dopant on the cathode structure were studied using a suite of characterization tools including X-ray diffraction (XRD), Raman spectroscopy, and transmission electron microscopy (TEM). These measurements demonstrate that Mo6+ reduces Li+/Ni2+cation mixing and mitigates undesirable phase transformations near the cathode surface during cycling. This work also reports the use of an inorganic Mn2P2O7 coating which enhances cycling stability, presumably through formation of a stable cathode electrolyte interphase (CEI) layer. Overall, the synthesis approaches reported herein are quite general and can potentially be expanded to other high voltage LIB cathodes.

Co-free cathodes, d0 cation, pyrophosphate coating↗
DOE OSTI2022

Grid-Forming and Grid-Following Inverter Comparison of Droop Response

With the increase in penetration of inverter-based resources (IBRs) in the electrical power system, the ability of these devices to provide grid support to the system has become a necessity. With standards previously developed for the interconnection requirements of grid-following inverters (GFLI) (most commonly photovoltaic inverters), it has been well documented how these inverters “should” respond to changes in voltage and frequency. However, with other IBRs such as grid-forming inverters (GFMIs) (used for energy storage systems, standalone systems, and as uninterruptable power supplies) these requirements are either: not yet documented, or require a more in deep analysis. With the increased interest in microgrids, GFMIs that can be paralleled onto a distribution system have become desired. With the proper control schemes, a GFMI can help maintain grid stability through fast response compared to rotating machines. This paper will present an experimental comparison of commercially available GFMI and GFLI ' responses to voltage and frequency deviation, as well as the GFMI operating as a standalone system and subjected to various changes in loads.

Grid Support, Inverter, Droop Control, Volt-VAR, F↗
DOE OSTI2024

Multifunctional nitrile additives for inducing pseudo-concentration gel-polymer electrolyte: Enabling stable high-voltage lithium metal batteries

High-voltage lithium metal batteries (LMBs) are promising for next-generation high-energy storage systems. Unfortunately, their implementation has been severely plagued by the interfacial instability between the high-voltage cathodes/lithium metal (LM) anodes and electrolytes. To tackle these challenges, a novel nitrile additive, 1,4-dicyanobenzene (DCB) (Synonyms: terephthalonitrile), is added to the in situ polymerized pentaerythritol tetraacrylate-based gel polymer electrolyte (GPE). The DCB additive, as demonstrated both theoretically and experimentally, plays a crucial role in altering the Li+ coordinated solvation structure within the GPE. This alteration leads to the formation of a pseudo-concentrated electrolyte with a tightly packed Li+ cluster, expanding the electrochemical stability window of the electrolyte. Moreover, the DCB-included GPE significantly improves its compatibility with both LM anode and high-voltage cathode, attributed to the modified solvation structure and the generated LiF-rich electrolyte/electrode interphases. Accordingly, the GPE enables stable cyclic performance of LMBs based on a 4.9 V LiNi 0.5 Mn 1.5 O 4 cathode at a low relative negative/positive ratio of 4, achieving a high reversible capacity of 123.8 mAh g -1 with a capacity retention of 87.7% over 500 cycles at 0.5 C. This work provides new insights into enhancing the cyclability of high-voltage LMBs via the synergistic effect of additives and GPE.

25 ENERGY STORAGE↗
DOE OSTI2022

Investigation of long-term light stability of negative charge injected into oxide-nitride-oxide passivation stack of crystalline silicon solar cells

A negatively charged oxide-nitride-oxide stack for field-effect passivation of crystalline silicon solar cells is discussed. The negative charge was injected into the stack by a plasma charge injection technology. Charge stability was studied by exposing samples to AM1.5 simulation visible light and full-spectrum light at temperatures ranging from 55 to 78 °C for up to 300 h. Charge injection and loss were quantified based on shifts in the flatband voltage of capacitance–voltage curves measured with a mercury probe. The most probable mechanism of charge loss was found to be diffusion of negative charged hydrogen atoms through nitride and bottom oxide. The optimum recipe for each layer of the stack was investigated to minimize the loss of injected charge. The flatband voltage decay of the optimized stack was found to fit a power-law trend, suggesting the dispersive transport of hydrogen atoms with a dispersion parameter of ~0.06–0.07. The optimized stack is projected to maintain a negative charge density of about 3.6 × 10 12 cm –2 or more after 25 years of field operation in an environment such as Arizona, which would be sufficient for field-effect passivation under one-sun illumination. Furthermore, the high stability of the negative injected charge makes the plasma charging technology a safer and lower cost alternative to Al 2 O 3 -passivation technology commonly used to passivate p-type surfaces.

14 SOLAR ENERGY↗
DOE OSTI2021

Visual Tool for Assessing Stability of DER Configurations on Three-Phase Radial Networks

Here, we present a method and tool for evaluating the placement of Distributed Energy Resources (DER) on distribution circuits in order to control voltages and power flows. Our previous work described Phasor-Based Control (PBC), a novel control framework where DERs inject real and reactive power to track voltage magnitude and phase angle targets. Here, we employ linearized power flow equations and integral controllers to develop a linear state space model for PBC acting on a three-phase unbalanced network. We use this model to evaluate whether a given inverter-based DER configuration admits a stable set of controller gains, which cannot be done by analyzing controllability nor by using the Lyapunov equation. Instead, we sample over a parameter space to identify a stable set of controller gains. Our stability analysis requires only a line impedance model and does not entail simulating the system or solving an optimization problem. We incorporate this assessment into a publicly available visualization tool and demonstrate three processes for evaluating many control configurations on the IEEE 123-node test feeder (123NF).

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Stabilizing and understanding the interface between nickel-rich cathode and PEO-based electrolyte by lithium niobium oxide coating for high-performance all-solid-state batteries

The pursuit of high energy density and safe lithium ion batteries (LIBs) is the urgent goal for the development of next-generation electric vehicles (EVs). All-solid-state batteries (ASSBs) with the combination of poly(ethylene oxide) (PEO)-based solid polymer electrolyte (SPE) and Ni-rich lithium nickel manganese cobalt oxide LiNi0.8Mn0.1Co0.1O2 (NMC811) cathode are promising candidates for EVs due to their improved energy density and safety. However, the low electrochemical oxidation window of PEO-based SPE and the instability of NMC811 at the charge/discharge process seriously restrict the battery performance. Herein, a high voltage stable solid-state electrolyte layer lithium niobium oxide (LNO) is coated on the NMC811 electrode surface by atomic layer deposition for stabilizing NMC811-PEO solid polymer batteries. Electrochemical tests show that LNO coating can stabilize the NMC811 active materials and mitigate the decomposition of SPE upon the cycling process, rendering a good performance of NMC811-PEO solid polymer battery. Mechanism studies by SEM, STEM, XAS, and XPS disclose that the uncoated NMC811 suffers from chemomechanical degradations along with oxygen release triggering the decomposition of SPE, which results in unstable cathodic electrolyte interphase. With LNO coating, chemomechanical degradations and oxygen release are inhibited and the decomposition of SPE is mitigated. This paper renders a stable and high-performance high-energy-density SSB for high voltage application, which paves the way toward next-generation solid-state LIBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Optimized Al Doping Improves Both Interphase Stability and Bulk Structural Integrity of Ni-Rich NMC Cathode Materials

Ni-rich layered transition metal oxide (NMC, LiNi1-x-yMxCoyO2, 1 – x – y = 0.6) is promising for high-energy-density lithium-ion batteries, but its large-scale application is still hindered by several technical challenges, including secondary particle cracking, interfacial instability, and cell degassing during cycling. Here, we report a facile wet-chemical method to modify both the surface and the bulk of the LiNi0.76Mn0.14Co0.10O2 (NMC76) cathode with Al doping to effectively improve the structural/interfacial stability of the cathode, and hence its long-term cycling capability. With only 1 mol% Al doping, the Al-NMC76 electrode delivers a good capacity retention of 79.2% after 500 cycles at a high voltage limit of 4.5 V, which is far better than those of undoped NMC76 under the similar condition. The enhanced performance can be attributed to the Al doping in the NMC76, which not only strengthens the bulk structural stability through doping into the lattice, but also suppresses acidic attack from the electrolyte through altered surface structure of NMC76.

Al doping, capacity retention, high voltage, elect↗
DOE OSTI2025

Robust Optimal Control of Inverter-Based Resources Under Grid-Forming Operation

In this paper, we propose and solve a robust control problem for inverter-based resources under grid-forming operation to regulate the voltage and frequency. One major challenge is to mitigate the effect of unmeasurable load current disturbance, grid and load parametric uncertainties. Moreover, strong coupling between the state variables on both the AC and DC sides, as well as between the modulating control input and the frequency impose additional challenges. To address these challenges, first, a robust control problem is solved at the high level via transformation into an equivalent, but more tractable, optimal control problem. Then, in the middle layer a voltage control law is designed on the one side, and a frequency control law on the other side. Finally, an inverter filter current controller is designed to complete the controller design. Theoretical results are derived to provide stability guarantees for the resulting closed-loop system. Specifically, we show that the inverter current injection error is dissipative, the frequency error is semi-globally asymptotically stable, and the inverter terminal voltage error is globally asymptotically stable, all with provided sufficient conditions. Here, numerical simulation experiments are used to validate the theoretical claims. Furthermore, the developed controller is compared with existing work in literature to show the efficacy of the proposed approach.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Enabling High-Temperature and High-Voltage Lithium-Ion Battery Performance through a Novel Cathode Surface-Targeted Additive

We report lithium-ion batteries (LIBs) are being used in locations and applications never imagined when they were first conceived. To enable this broad range of applications, it has become necessary for LIBs to be stable to an ever broader range of conditions, including temperature and energy. Unfortunately, while negative electrodes have received a great deal of focus in electrolyte development, stabilization of positive electrodes remains an elusive target. Here, we report a novel additive that shows the ability to protect positive electrodes against elevated temperatures and voltages. This additive can be used in small quantities, and its targeted behavior allows it to remain functional in complex electrolyte packages. This can prove an effective approach to targeting specific aspects of cell performance.

25 ENERGY STORAGE↗
DOE OSTI2022

Advanced Power-Hardware-in-the-Loop Evaluation of Inverter-Based Resources (IBRs)

Power-hardware-in-the-loop evaluation of IBRs has become more and more important as it provides reliable testing results to investigate the real responses of inverters with interconnected systems. A successful laboratory PHIL testing gives confidence of the hardware system to be deployed and de-risk technology integration prior to field deployment. So far, there are two important applications for PHIL evaluation: (1) test stability and functionality of large utility inverters into the system when it interconnects to the distribution systems/microgrids; and (2) test the collective grid service that inverters can provide to the grid. For the first application, the PHIL evaluation has high requirements for the stability and accuracy of the PHIL interface as the close-loop in digital real time simulator (DRTS) should replicate the actual current and voltage dynamics in the inverter. This is challenging because of the delays, sensing errors, nonlinearities of inverters, and hardware bandwidth limitations of the elements in the HIL loop. For the second application, multiple inverters will be tested resulting in multiple PCCs, which naturally causes competing dynamics and oscillations among hardware inverters if traditional PHIL interface is used. Therefore, new PHIL interface should be developed to compromise between stability and accuracy and represent the dispatched grid services for the hardware inverters. In this presentation, we will share our latest work in developing PHIL interface in these two applications to address the two key challenges.

DERMS↗