Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “shift current”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

dc electrical conductivity in strongly magnetized plasmas

A generalized Ohm's law is derived to treat strongly magnetized plasmas in which the electron gyrofrequency significantly exceeds the electron plasma frequency. Here, strong magnetization of electrons causes the frictional drag between electrons and ions due to Coulomb collisions to shift, producing an additional transverse resistivity term in the generalized Ohm's law that is perpendicular to both the current ($J$) and the Hall ($JxB$) direction. In the limit of very strong magnetization the parallel resistivity is found to increase by a factor of 3/2, and the perpendicular resistivity by a factor of $\frac{3}{4} \ln (m_i/m_e)$, where $m_i$ and $m_e$ are the ion and electron masses. These results suggest that strong magnetization significantly changes the magnetohydrodynamic evolution of a plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fast response, optical radiance measurements of low intensity impurity emission in WEST plasmas with staggered wavelength filters

Fast response acquisition of atomic line emission through the use of a filterscope has been implemented on the WEST tokamak at multiple poloidal locations. Filterscopes consist of a fiber-optic-based transmission from the tokamak to specifically engineered optical bandpasses and photomultiplier tubes (PMT) that collect the emission intensity to measure a radiance, L [W/cm2/str], over the specified bandpass. This diagnostic records plasma-wall interaction (PWI) properties (e.g. impurity emission and recycling of main fuel ions) up to a max acquisition rate of 100 kHz. These PMT radiometric measurements are calibrated into a line-normalized radiance, LN [photons/sec/cm2/str], similar to traditional spectrometers, which can later be converted to a particle flux. Low intensity emission peaks are difficult to quantify due to often comparable continuum levels, thus a secondary filter shifted to a judiciously-selected, line-free region (~1 nm away) allows for background subtraction. The system currently installed on WEST targets tungsten (W) gross sputtering specifically by monitoring, with a filter pair, the spectral region near the neutral W line emission (W I 400.9 nm). The line and background filters of the pair are centered at 400.6 nm and 403.1 nm, respectively. Through a set beam splitters on each sight line, the filter pair are measuring from the same location. The two L signals near W I are then subtracted from each other yielding only the W I LN. W I LN data from a recent WEST experimental campaign is presented and compared with plasma parameters and traditional spectrometer measurements of W I line emission to demonstrate the capabilities of this staggered-filter filterscope method. Specifically, the choice of WEST-specific bandpass curves for the W I LN will be illustrated based on this latter comparison.

Neff, Anton↗

Using quasar X-ray and UV flux measurements to constrain cosmological model parameters

ABSTRACT Risaliti and Lusso have compiled X-ray and UV flux measurements of 1598 quasars (QSOs) in the redshift range 0.036 ≤ z ≤ 5.1003, part of which, z ∼ 2.4 − 5.1, is largely cosmologically unprobed. In this paper we use these QSO measurements, alone and in conjunction with baryon acoustic oscillation (BAO) and Hubble parameter [H(z)] measurements, to constrain cosmological parameters in six different cosmological models, each with two different Hubble constant priors. In most of these models, given the larger uncertainties, the QSO cosmological parameter constraints are mostly consistent with those from the BAO + H(z) data. A somewhat significant exception is the non-relativistic matter density parameter Ωm0 where QSO data favour Ωm0 ∼ 0.5 − 0.6 in most models. As a result, in joint analyses of QSO data with H(z) + BAO data the 1D Ωm0 distributions shift slightly towards larger values. A joint analysis of the QSO + BAO + H(z) data is consistent with the current standard model, spatially-flat ΛCDM, but mildly favours closed spatial hypersurfaces and dynamical dark energy. Since the higher Ωm0 values favoured by QSO data appear to be associated with the z ∼ 2 − 5 part of these data, and conflict somewhat with strong indications for Ωm0 ∼ 0.3 from most z < 2.5 data as well as from the cosmic microwave background anisotropy data at z ∼ 1100, in most models, the larger QSO data Ωm0 is possibly more indicative of an issue with the z ∼ 2 − 5 QSO data than of an inadequacy of the standard flat ΛCDM model.

79 ASTRONOMY AND ASTROPHYSICS↗

Design Optimization for Weighted Conduction Loss Minimization in a Dual-Active-Bridge-Based PV Microinverter

This manuscript presents a harmonic-superposition based frequency-domain approach for analysis and optimal design of a single-stage DAB-based DC-AC converter used in low-voltage DC to high voltage AC applications, such as PV microinverter. Specifically, two topological variations and correspondingly different modulation strategies involving up to four control variables (three phase shifts and switching frequency) are analyzed. Optimal trajectories of control variables are determined that result in minimized transformer RMS current at a given average power, while enforcing near-uniform ZVS. To make the design process holistic, an outer optimization loop is used to determine optimal values for the power transfer inductance (integrated as the transformer’s leakage inductance) and turns ratio, which minimize the weighted-average conduction loss contribution to the microinverter’s CEC efficiency. Based on the optimization analyses, a 400 W microinverter prototype is built and experimental results at one operating point are presented, achieving a measured efficiency of 92.8%.

14 SOLAR ENERGY↗

Polysulfide-Permanganate Flow Battery Using Abundant Active Materials

A new flow battery is presented using the abundant and inexpensive active material pairs permanganate/manganate and disulfide/tetrasulfide. A wetted material set is identified for compatibility with the strongly oxidizing manganese couple at ambient and elevated temperatures. Both solutions allow high active material solubility, with cells tested at theoretical energy densities up to 43 Wh l −1 for the ∼1.2 V cell. Full cells built with nickel foam electrodes and sodium-exchanged Nafion 115 membranes deliver a baseline area-specific resistance of 2.7 Ω-cm 2 . Incorporation of high-surface-area cobalt-coated carbon paper and high-surface-area stainless steel mesh electrodes, and an expanded Nafion 115 membrane delivers cells with 44% lower resistance at 1.6 Ω-cm 2 . All cells show performance decay over the course of cycling. The Co-decorated carbon paper electrodes provide significant kinetic improvements, shifting electrode performance from non-linear with Ni-foam to linear with a volume-normalized exchange current density value of 3.2 A cm −3 . The expanded membrane provides increased conductivity over the 13 mS cm −1 conductivity observed in as-received, sodium-exchanged Nafion 115. Although boiled membranes provide improved conductivity, it is at the cost of decreased Coulombic efficiency and poorer manufacturability. Full cell models suggest that similar cell resistances (1.7 Ω-cm 2 ) should be feasible with as-received Nafion 115 and advanced electrodes.

25 ENERGY STORAGE↗

AD_LTEM

This software uses AI tools for enhanced functional imaging using Lorentz transmission electron microscopy by retrieving phase shift at higher spatial resolution, and under noisy conditions. This is a companion code for a publication that is currently being submitted (APT # 164160).

PHATAK, CHARUDATTA↗

Using root and soil traits to forecast woody encroachment dynamics in mesic grassland

Grasslands are a widespread and globally important biome providing key ecosystem services including C storage and regulation of the water cycle. Grasslands face multiple threats, including changes in drought intensity and woody encroachment - a process that results in increased woody plant abundance corresponding with decreased herbaceous plant abundance. The combination of reduced soil moisture and shifts in plant dominance from herbaceous to woody are likely to alter C pools in the soil profile. We currently do not have the capacity to predict either the magnitude or rates of change in these C pools. In order to predict changes in grassland vegetation structure and the associated impacts on C cycling requires greater understanding of changes in soil C pools at multiple soil depths, and the responses of these pools to changes in precipitation. To support and perform this parameterization of Land Surface Models, we performed detailed investigations of root (anatomical and physiological) and soil traits (microbial function) at varying soil depths, to capture the belowground impacts of changing dominant plant growth forms (grasses to shrubs) and the impacts of frequent drought.

54 ENVIRONMENTAL SCIENCES↗

Assessment of Machine Learning for Ultrasonic Nondestructive Evaluation of Alkali–Silica Reaction in Concrete

Alkali–silica reaction (ASR) is a type of material degradation in concrete structures that leads to concrete cracking and rebar corrosion, thereby reducing the material’s structural integrity and the overall structure’s lifetime and raising safety concerns. Ultrasonic nondestructive evaluation (NDE) has been proven to be a valuable technique for assessing concrete properties and monitoring ASR progression in concrete. However, the deployment and analysis of ultrasonic NDE and its data requires specialized expertise, often relying on the engineer’s subjective interpretation. With the surge in computational power, artificial intelligence (AI) and machine learning (ML) algorithms have become popular in automating NDE data analysis. Various industrial sectors are increasingly adopting ML algorithms for NDE data analysis with a growing emphasis on AI–assisted automation. Regulatory agencies are also preparing for this technological shift, anticipating corresponding revisions in standards. Thus, there is an urgent need to identify the capabilities and limitations of current ML technologies for the evaluation of concrete material properties and damage status. Furthermore, the effects of various factors on ML model performance must be thoroughly investigated. The study summarized herein evaluated the effectiveness of two ML models (i.e., support vector regression (SVR) and deep neural network (DNN)) in predicting concrete material damage induced by ASR based on the long-term ultrasonic monitoring data. Four distinct concrete specimens were cast with artificially induced ASR, and over a period exceeding 500 days, ultrasonic signals and expansion data were continuously collected. For the SVR model, wave velocity and 12 other wave features were extracted from the ultrasonic signals, with 6 out of 13 features selected as input for the model. Different combinations of training and testing datasets were designed to explore factors influencing prediction performance, including the range of data within training and testing sets, in addition to various signal preprocessing methodologies. These findings suggest the importance of using a training dataset with a broader data range compared with testing datasets for improved model performance alongside consistent signal preprocessing across datasets.

36 MATERIALS SCIENCE↗

Online characterization of primary and secondary emissions of particulate matter and acidic molecules from a modern fleet of city buses

The potential impact of transitioning from conventional fossil fuel to a non-fossil-fuel vehicle fleet was investigated by measuring primary emissions via extractive sampling of bus plumes and assessing secondary mass formation using the Gothenburg Potential Aerosol Mass (Go:PAM) reactor from 76 in-use transit buses. Online chemical characterization of gaseous and particulate emissions from these buses was conducted using chemical ionization mass spectrometry (CIMS) with acetate as the reagent ion, coupled with the Filter Inlet for Gases and AEROsols (FIGAERO). Acetate reagent ion chemistry selectively ionizes acidic compounds, including organic and inorganic acids, as well as nitrated and sulfated organics. A significant reduction (48 %–98 %) in fresh particle emissions was observed in buses utilizing compressed natural gas (CNG), biodiesels like rapeseed methyl ester (RME) and hydrotreated vegetable oil (HVO), and hybrid-electric HVO (HVO HEV ) compared to diesel (DSL). However, secondary particle formation from photooxidation of emissions was substantial across all the fuel types. The median ratio of particle mass emission factors of aged to fresh emissions increased in the following order: DSL buses at 4.0, HVO buses at 6.7, HVO HEV buses at 10.5, RME buses at 10.8, and CNG buses at 84. Of the compounds that can be identified by CIMS, fresh gaseous emissions from all Euro V/EEV (Enhanced Environmentally friendly Vehicle) buses, regardless of fuel type, were dominated by nitrogen-containing compounds such as nitrous acid (HONO), nitric acid (HNO 3 ), and isocyanic acid (HNCO), alongside small monoacids (C 1 –C 3 ). Notably, the emission of nitrogen-containing compounds was lower in Euro VI buses equipped with more advanced emission control technologies. Secondary gaseous organic acids correlated strongly with gaseous HNO 3 signals (R 2 =0.85–0.99) in Go:PAM, but their moderate to weak correlations with post-photooxidation secondary particle mass suggest that they are not reliable tracers of secondary organic aerosol formation from bus exhaust. Our study highlights that non-regulated compounds and secondary pollutant formation, not currently addressed in legislation, are crucial considerations in the evaluation of environmental impacts of future fuel and engine technology shifts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Investigation of environmental change pattern in Japan. Utilization of LANDSAT-2 data for fisheries

The author has identified the following significant results. MSS data provided extensive and simultaneous information about marine environmental conditions, such as the shift of the Kuroshio, fall and rise of coastal water mass, distribution of water masses, locations of vortex and current rips, exchanges of water between embayment and open ocean effluent rivers, fertility of plankton, red tide, pollution, etc.

Maruyasu, T.↗

On the sensitivity of numerical weather prediction to remotely sensed marine surface wind data - A simulation study

The reported investigation has the objective to assess the potential impact on numerical weather prediction (NWP) of remotely sensed surface wind data. Other investigations conducted with similar objectives have not been satisfactory in connection with a use of procedures providing an unrealistic distribution of initial errors. In the current study, care has been taken to duplicate the actual distribution of information in the conventional observing system, thus shifting the emphasis from accuracy of the data to the data coverage. It is pointed out that this is an important consideration in assessing satellite observing systems since experience with sounder data has shown that improvements in forecasts due to satellite-derived information is due less to a general error reduction than to the ability to fill data-sparse regions. The reported study concentrates on the evaluation of the observing system simulation experimental design and on the assessment of the potential of remotely sensed marine surface wind data.

Cane, M. A.↗

Estimating SAR Doppler Shifts From Quasi-Homogeneous Targets

Linear-estimator subalgorithm optimized for local terrain. Algorithm processes some of information in synthetic-aperture-radar echoes from quasi-homogeneous targets, yielding optimal estimates of Doppler frequency shifts. Differs from one described in article, "Estimating SAR Doppler Shifts From Homogeneous Targets", NPO-17869, though offers similar advantages for measurements of wind shears and speeds of ocean currents. Derivation of algorithm involves some of same terminology and simplifying assumptions, however, target area considered quasi-homogeneous in sense it consists of patchwork of subareas, each of which is homogeneous target differing from its neighbors. This assumption more realistic than assumption of homogeneity.

Jin, Michael Y.↗

Advanced p-MOSFET Ionizing-Radiation Dosimeter

Circuit measures total dose of ionizing radiation in terms of shift in threshold gate voltage of doped-channel metal oxide/semiconductor field-effect transistor (p-MOSFET). Drain current set at temperature-independent point to increase accuracy in determination of radiation dose.

Buehler, Martin G.↗

Multiplexer/Demultiplexer Loading Tool (MDMLT)

The purpose of the MDMLT is to improve the reliability and speed of loading multiplexers/demultiplexers (MDMs) in the Software Development and Integration Laboratory (SDIL) by automating the configuration management (CM) of the loads in the MDMs, automating the loading procedure, and providing the capability to load multiple or all MDMs concurrently. This loading may be accomplished in parallel, or single MDMs (remote). The MDMLT is a Web-based tool that is capable of loading the entire International Space Station (ISS) MDM configuration in parallel. It is able to load Flight Equivalent Units (FEUs), enhanced, standard, and prototype MDMs as well as both EEPROM (Electrically Erasable Programmable Read-Only Memory) and SSMMU (Solid State Mass Memory Unit) (MASS Memory). This software has extensive configuration management to track loading history, and the performance improvement means of loading the entire ISS MDM configuration of 49 MDMs in approximately 30 minutes, as opposed to 36 hours, which is what it took previously utilizing the flight method of S-Band uplink. The laptop version recently added to the MDMLT suite allows remote lab loading with the CM of information entered into a common database when it is reconnected to the network. This allows the program to reconfigure the test rigs quickly between shifts, allowing the lab to support a variety of onboard configurations during a single day, based on upcoming or current missions. The MDMLT Computer Software Configuration Item (CSCI) supports a Web-based command and control interface to the user. An interface to the SDIL File Transfer Protocol (FTP) server is supported to import Integrated Flight Loads (IFLs) and Internal Product Release Notes (IPRNs) into the database. An interface to the Monitor and Control System (MCS) is supported to control the power state, and to enable or disable the debug port of the MDMs to be loaded. Two direct interfaces to the MDM are supported: a serial interface (debug port) to receive MDM memory dump data and the calculated checksum, and the Small Computer System Interface (SCSI) to transfer load files to MDMs with hard disks. File transfer from the MDM Loading Tool to EEPROM within the MDM is performed via the MILSTD- 1553 bus, making use of the Real- Time Input/Output Processors (RTIOP) when using the rig-based MDMLT, and via a bus box when using the laptop MDMLT. The bus box is a cost-effective alternative to PC-1553 cards for the laptop. It is noted that this system can be modified and adapted to any avionic laboratory for spacecraft computer loading, ship avionics, or aircraft avionics where multiple configurations and strong configuration management of software/firmware loads are required.

Brewer, Lenox Allen↗

A Phase-Shifting Zernike Wavefront Sensor for the Palomar P3K Adaptive Optics System

A phase-shifting Zernike wavefront sensor has distinct advantages over other types of wavefront sensors. Chief among them are: 1) improved sensitivity to low-order aberrations and 2) efficient use of photons (hence reduced sensitivity to photon noise). We are in the process of deploying a phase-shifting Zernike wavefront sensor to be used with the realtime adaptive optics system for Palomar. Here we present the current state of the Zernike wavefront sensor to be integrated into the high-order adaptive optics system at Mount Palomar's Hale Telescope.

adaptive optics↗

The Behavior of Environmentally Friendly Corrosion Preventative Compounds in an Aggressive Coastal Marine Environment

The shift to use environmentally friendly technologies throughout future space-related launch programs prompted a study aimed at replacing current petroleum and solvent-based Corrosion Preventive Compounds (CPCs) with environmentally friendly alternatives. The work in this paper focused on the identification and evaluation of environmentally friendly CPCs for use in protecting flight hardware and ground support equipment from atmospheric corrosion. The CPCs, while a temporary protective coating, must survive in the aggressive coastal marine environment that exists throughout the Kennedy Space Center, Florida. The different protection behaviors of fifteen different soft film CPCs, both common petroleum-based and newer environmentally friendly types, were evaluated on various steel and aluminum substrates. The CPC and substrate systems were subjected to atmospheric testing at the Kennedy Space Center's Beachside Atmospheric Corrosion Test Site, as well as cyclic accelerated corrosion testing. Each CPC also underwent physical characterization and launch-related compatibility testing . The initial results for the fifteen CPC systems are reported : Key words: corrosion preventive compound, CPC, spaceport, environmentally friendly, atmospheric exposure, marine, carbon steel, aluminum alloy, galvanic corrosion, wire on bolt.

Montgomery, Eliza L.↗

New York City Panel on Climate Change 2019 Report Chapter 9: Perspectives on a City in a Changing Climate 2008-2018

Cities experience multiple environmental shifts, stresses, and shocks—such as air and water pollution—and a variety of extreme events simultaneously and continuously. Current urban programs have focused on limiting the impacts of these conditions through a portfolio of multifaceted strategies, such as regulations and codes, management and restoration projects, and citizen engagement. Global climate change represents a new environmental dynamic to which cities now have to respond. While global climate change by definition has impacts world wide, residents and managers of cities, like New York, typically perceive changes in their own local environments. In most cities, temperature is warming with increasingly hotter and longer heatwaves, and heavier downpours are leading to more frequent inland flooding. In coastal cities, sea levels are rising, exacerbating coastal flooding. Analyzing and understanding the impacts of climate change on cities is important because of the dramatic growth in urban populations throughout the world. An estimated nearly 4.0 billion people reside in urban areas, accounting for 52% of the world’s population (UN, 2017). That percentage will increase dramatically in the coming decades as almost all of the growth to take place up to 2050 will be in urban areas (UN, 2017). The New York City metropolitan region (NYMR)—the five boroughs (equivalent to counties) of New York City and the adjacent 26 counties in the states of New York, New Jersey, and Connecticut—is an ideal model of an urban agglomeration. Approximately 8.6 million people live in the five boroughs and more than 15 million people live in the neighboring smaller cities, towns, and villages (City of New York, 2018a; US Census, 2017). The population of the five boroughs is projected to add 1 million people by 2030, while the total region is projected to reach 26.1 million (NYTC, 2015).

Solecki, William↗

Interannual Variability in the Thermal Habitat of Alexandrium catenella in the Bay of Fundy and the Implications of Climate Change

Globally, harmful algal blooms (HABs) are an increasing problem. In the Gulf of Maine and Bay of Fundy, blooms of the toxic dinoflagellate Alexandrium catenella are annually recurrent phenomena. As this region is one of the most rapidly warming areas of the global ocean, an improved understanding of the mechanisms driving the initiation of local A. catenella blooms, their interannual variability and the implications of future climate change is critical to local monitoring strategies and marine resources management. A 27-year (1988–2014) time series of weekly A. catenella cell counts from the Bay of Fundy and concurrent satellite-measured sea surface temperature, freshwater discharge from the St. John River and wind-driven turbulence are compared to assess their relationship to variability in bloom phenology metrics. The mean thermal habitat associated with early detection of A. catenella is 6.5 ± 1.6°C, whereas that of bloom initiation averages 9.2 ± 1.5°C. Both thermal habitats for A. catenella are trending earlier over the study period. Bloom initiations that precede the arrival of the thermal habitat mean (occur in colder water) are associated with higher spring freshwater discharge and are generally weaker blooms. Increased spring freshwater discharge is also associated with earlier bloom initiation and earlier maximum concentration dates. No significant relationship was observed with the strength of wind-driven mixing. Removal of the mean thermal seasonal cycle shows that surface temperature anomalies have a strong negative relationship to the bloom phenology metrics and arrival of thermal habitat: warmer years are linked to earlier arrival of thermal habitats (∼12 days °C–1) and earlier detection and bloom initiation dates (∼33 days °C–1). Using these relationships and present trends in Bay of Fundy surface temperature warming over the period 1982–2019, we project the arrival dates of bloom thermal habitat and bloom phenology metrics out to the middle of this century. Based on current rates of sea surface temperature change, bloom phenology metrics (e.g., bloom initiation, early detection), can be expected to shift 1–2 months earlier in the season by mid-century. Such changes in the phenology of A. catenella blooms will need to be incorporated into both monitoring strategies and forecasting models for the region.

Andre F. Bucci↗