Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “safety evaluation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Evaluating Mass Analyzers as Candidates for Small, Portable, Rugged Single Point Mass Spectrometers for Analysis of Permanent Gases

For Space Shuttle launch safety, there is a need to monitor the concentration of H2, He, O2 and Ar around the launch vehicle. Currently a large mass spectrometry system performs this task, using long transport lines to draw in samples. There is great interest in replacing this stationary system with several miniature, portable, rugged mass spectrometers which act as point sensors which can be placed at the sampling point. Five commercial and two non-commercial analyzers are evaluated. The five commercial systems include the Leybold Inficon XPR-2 linear quadrupole, the Stanford Research (SRS-100) linear quadrupole, the Ferran linear quadrupole array, the ThermoQuest Polaris-Q quadrupole ion trap, and the IonWerks Time-of-Flight (TOF). The non-commercial systems include a compact double focusing sector (CDFMS) developed at the University of Minnesota, and a quadrupole ion trap (UF-IT) developed at the University of Florida. The System Volume is determined by measuring the entire system volume including the mass analyzer, its associated electronics, the associated vacuum system, the high vacuum pump and rough pump. Also measured are any ion gauge controllers or other required equipment. Computers are not included. Scan Time is the time required for one scan to be acquired and the data to be transferred. It is determined by measuring the time required acquiring a known number of scans and dividing by said number of scans. Limit of Detection is determined first by performing a zero-span calibration (using a 10-point data set). Then the limit of detection (LOD) is defined as 3 times the standard deviation of the zero data set. (An LOD of 10 ppm or less is considered acceptable.)

Arkin, C. Richard↗
NASA NTRS2005

Flight Test Comparison Between Enhanced Vision (FLIR) and Synthetic Vision Systems

Limited visibility and reduced situational awareness have been cited as predominant causal factors for both Controlled Flight Into Terrain (CFIT) and runway incursion accidents. NASA s Synthetic Vision Systems (SVS) project is developing practical application technologies with the goal of eliminating low visibility conditions as a causal factor to civil aircraft accidents while replicating the operational benefits of clear day flight operations, regardless of the actual outside visibility condition. A major thrust of the SVS project involves the development/demonstration of affordable, certifiable display configurations that provide intuitive out-the-window terrain and obstacle information with advanced pathway guidance. A flight test evaluation was conducted in the summer of 2004 by NASA Langley Research Center under NASA s Aviation Safety and Security, Synthetic Vision System - Commercial and Business program. A Gulfstream G-V aircraft, modified and operated under NASA contract by the Gulfstream Aerospace Corporation, was flown over a 3-week period at the Reno/Tahoe International Airport and an additional 3-week period at the NASA Wallops Flight Facility to evaluate integrated Synthetic Vision System concepts. Flight testing was conducted to evaluate the performance, usability, and acceptance of an integrated synthetic vision concept which included advanced Synthetic Vision display concepts for a transport aircraft flight deck, a Runway Incursion Prevention System, an Enhanced Vision Systems (EVS), and real-time Database Integrity Monitoring Equipment. This paper focuses on comparing qualitative and subjective results between EVS and SVS display concepts.

Arthur, Jarvis J., III↗
NASA NTRS2019

Evaluation of Impact Energy Attenuators and Composite Material Designs of a UAM VTOL Concept Vehicle

The development of Vertical Take-off and Landing (VTOL) vehicles for the Urban Air Mobility (UAM) markets presents a need for light weight vehicle structures with effective occupant protection capabilities. The National Aeronautics and Space Administration (NASA) has been working to fill that need, recently developing a cadre of concept vehicles to help characterize UAM design feasibility. This paper describes a study, using these concept vehicles, to evaluate the use of advanced composite structure and energy attenuating designs in the UAM vehicle design space. A finite element model (FEM) of a single passenger quadrotor concept vehicle was developed in LS-Dyna® and simulated under nominal and off-nominal vertical impact conditions. A variety of energy attenuating design mechanisms were implemented within this model to quantify their effectiveness in improving occupant safety. The use of carbon composites in both the energy attenuation mechanisms and vehicle structure was evaluated. The results of this study found significant reduction in occupant injury risk with the implementation of energy absorbing composite crush tubes and landing gear within the vehicle design. Additionally the use of a carbon fiber as a structural material was found to provide significant weight reduction while maintaining similar occupant loads to that predicted with an aluminum structure. This work provides a preliminary evaluation of design mechanisms and materials that may be used to optimize occupant protection capabilities within the UAM market.

Putnam, Jacob↗
NASA NTRS2012

Performance Testing of Yardney MCMB-LiNiCoAlO2 Lithium-ion Cells Possessing Electrolytes with Improved Safety Characteristics

Many future NASA missions aimed at exploring the Moon and Mars require high specific energy rechargeable batteries that possess enhanced safety characteristics. There is also a strong desire to develop Li-ion batteries with improved safety characteristics for terrestrial applications, most notably for HEV and PHEV automotive applications. In previous work focused upon evaluating various potential flame retardant additives1, triphenyl phosphate (TPP)2 was observed to have the most desirable attributes, including good life characteristics and resilience to high voltage operation. We have employed a number of approaches in the design of promising TPP-based electrolytes with improved safety, including: (a) varying the flame retardant additive (FRA) content (from 5 to 15%), (b) the use of fluorinated co-solvents, (c) the use of additives to improve compatibility, and (c) the use of ester co-solvents to decrease the viscosity and increase the conductivity. In recent work, we have demonstrated a number of these electrolyte formulations to be compatible with a number of chemistries, including: MCMB carbon-LiNi0.8Co0.2O2, graphite-LiNi0.8Co0.15Al0.05O2, Li-Li(Li0.17Ni 0.25 Mn 0.58 )O2, Li-LiNiCoMnO2 and graphite- LiNiCoMnO2.3,4 In the current study, we have demonstrated the performance of a number of TPP-containing electrolytes in 7 Ah prototype MCMB-LiNiCoO2 cells. We will describe the results of a number of performance tests, including: a) 100% DOD cycle life testing at various temperatures, b) discharge rate characterization as a function of temperature, c) charge rate characterization as a function of temperature, and d) impedance as a function of temperature. In addition to displaying good life characteristics, being comparable to baseline chemistries, a number of cells were observed to provide good performance over a wide temperature range.

Li-ion batteries↗
NASA NTRS1975

Finite element analysis using NASTRAN applied to helicopter transmission vibration/noise reduction

A finite element NASTRAN model of the complete forward rotor transmission housing for the Boeing Vertol CH-47 helicopter was developed and applied to reduce transmission vibration/noise at its source. In addition to a description of the model, a technique for vibration/noise prediction and reduction is outlined. Also included are the dynamic response as predicted by NASTRAN, test data, the use of strain energy methods to optimize the housing for minimum vibration/noise, and determination of design modifications which will be manufactured and tested. The techniques presented are not restricted to helicopters but are applicable to any power transmission system. The transmission housing model developed can be used further to evaluate static and dynamic stresses, thermal distortions, deflections and load paths, fail-safety/vulnerability, and composite materials.

Howells, R. W.↗
NASA NTRS1983

Developing Standards for Phtotvoltaic Devices

Ground rules outlined for evaluating photovoltaic technology. Document addresses number of performance attributes: electrical, thermal, mechanical, structural, safety, reliability, durability, installation, operation, maintenance, building and site. Each criterion includes user need or expectation for element and describes method of test.

Hoffman, A. R.↗
NASA NTRS2001

Damage Assessment of Creep Tested and Thermally Aged Metallic Alloys Using Acousto-Ultrasonics

In recent years emphasis has been placed on the early detection of material changes experienced in turbine powerplant components. During the scheduled overhaul of a turbine, the current techniques of examination of various hot section components aim to find flaws such as cracks, wear, and erosion, as well as excessive deformations. Thus far, these localized damage modes have been detected with satisfactory results. However, the techniques used to find these flaws provide no information on life until the flaws are actually detected. Major improvements in damage assessment, safety, as well as more accurate life prediction could be achieved if nondestructive evaluation (NDE) techniques could be utilized to sense material changes that occur prior to the localized defects mentioned. Because of elevated temperatures and excessive stresses, turbine components may experience creep behavior. As a result, it is desirable to monitor and access the current condition of such components. Research at the NASA Glenn Research Center involves developing and utilizing an NDE technique that discloses distributed material changes that occur prior to the localized damage detected by the current methods of inspection. In a recent study, creep processes in a nickel-base alloy were the life-limiting condition of interest, and the NDE technique was acousto-ultrasonics (AU). AU is an NDE technique that utilizes two ultrasonic transducers to interrogate the condition of a test specimen. The sending transducer introduces an ultrasonic pulse at a point on the surface of the specimen while a receiving transducer detects the signal after it has passed through the material. The goal of the method is to correlate certain parameters of the detected waveform to characteristics of the material between the two transducers. Here, the waveform parameter of interest is the attenuation due to internal damping for which information is being garnered from the frequency domain. The parameters utilized to indirectly quantify the attenuation are the ultrasonic decay rate as well as various moments of the frequency power spectrum. A new, user-friendly, graphical interface AU system was developed at NASA Glenn. This system is an all-inclusive, multifunction system that controls the sending and receiving ultrasonic transducers as well as all posttest signal analysis. The system's postprocessing software calculates the multiple parameters used to study the material of interest.

Gyekenyesi, Andrew L.↗
NASA NTRS2007

Recovery of Space Shuttle Columbia and Return to Flight of Space Shuttle Discovery

NASA has come a long way in our journey to reduce the risks of operating the Spse Shuttle system. The External Tank bipod Thermal Protection System has been redesigned to eliminate the proximate cause of the Columbia accident. In all areas, we have applied the collective knowledge and capabilities of our Nation to comply with the Columbia Accident Investigation Board recommendations and to raise the bar beyond that. We have taken prudent technical action on potential threats to review and verify the material condition of all critical areas where failure could result in catastrophic loss of the crew and vehicle. We are satisfied that critical systems and elements should operate as intended-safely and reliably. While we will never eliminate all the risks from our human space flight programs, we have eliminated those we can and reduced, controlled, and/or mitigated others. The remaining identified risks will be evaluated for acceptance. Our risk reduction approach has its roots in the system safety engineering hierarchy for hazard abatement long employed in aerospace systems engineering. The components of the hierarchy are, in order of precedence, to: design/redesign; eliminate the hazard/risk; reduce the hazard/risk; and control the hazard/risk and/or mitigate the consequence of the remaining hazard/risk through warning devices, special procedures/capabilities, and/or training. This proven approach to risk reduction has been applied to potential hazards and risks in all critical areas of the Space Shuttle and has guided us through the technical challenges, failures, and successes present in return to flight endeavors. This approach provides the structured deliberation process required to verify and form the foundation for accepting any residual risk across the entire Space Shuttle Program by NASA leadership.

Rudolphi, Michael U.↗
NASA NTRS2004

Los Angeles International Airport Runway Incursion Studies: Phase III--Center-Taxiway Simulation

Phase III of the Los Angeles International Airport Runway Incursion Studies was conducted, under an agreement with HNTB Corporation, at the NASA Ames FutureFlight Central (FFC) facility in June 2003. The objective of the study was the evaluation of a new center-taxiway concept at LAX. This study is an extension of the Phase I and Phase II studies previously conducted at FFC. This report presents results from Phase III of the study, in which a center-taxiway concept between runways 25L and 25R was simulated and evaluated. Phase III data were compared objectively against the Baseline data. Subjective evaluations by participating LAX controllers were obtained with regard to workload, efficiency, and safety criteria. To facilitate a valid comparison between Baseline and Phase III data, the same scenarios were used for Phase III that were tested during Phases I and II. This required briefing participating controllers on differences in airport and airline operations between 2001 and today.

Madson, Michael D.↗
NASA NTRS2010

Portable Diagnostics Technology Assessment for Space Missions: Market Survey - Part 2

A mission to Mars of several years duration requires more demanding standards for all onboard instruments than a 6-month mission to the Moon or the International Space Station. In Part 1, we evaluated generic technologies and suitability to NASA needs. This prior work considered crew safety, device maturity and flightworthiness, resource consumption, and medical value. In Part 2, we continue the study by assessing the current marketplace for reliable Point-of-Care diagnostics. The ultimate goal of this project is to provide a set of objective analytical tools to suggest efficient strategies for reaching specific medical targets for any given space mission as program needs, technological development, and scientific understanding evolve.

Nelson, Emily S.↗
NASA NTRS2011

Ares I-X Separation and Reentry Trajectory Analyses

The Ares I-X Flight Test Vehicle was launched on October 28, 2009 and was the first and only test flight of NASA s two-stage Ares I launch vehicle design. The launch was successful and the flight test met all of its primary and secondary objectives. This paper discusses the stage separation and reentry trajectory analysis that was performed in support of the Ares I-X test flight. Pre-flight analyses were conducted to assess the risk of stage recontact during separation, to evaluate the first stage flight dynamics during reentry, and to define the range safety impact ellipses of both stages. The results of these pre-flight analyses were compared with available flight data. On-board video taken during flight showed that the flight test vehicle successfully separated without any recontact. Reconstructed trajectory data also showed that first stage flight dynamics were well characterized by pre-flight Monte Carlo results. In addition, comparisons with flight data indicated that the complex interference aerodynamic models employed in the reentry simulation were effective in capturing the flight dynamics during separation. Finally, the splash-down locations of both stages were well within predicted impact ellipses.

Tartabini, Paul V.↗
NASA NTRS2017

Evaluating Micrometeoroid and Orbital Debris Risk Assessments Using Anomaly Data

The accuracy of micrometeoroid and orbital debris (MMOD) risk assessments can be difficult to evaluate. A team from the National Aeronautics and Space Administration (NASA) Engineering and Safety Center (NESC) has completed a study that compared MMOD-related failures on operational satellites to predictions of how many of those failures should occur using NASA's TM"s MMOD risk assessment methodology and tools. The study team used the Poisson probability to quantify the degree of inconsistency between the predicted and reported numbers of failures. Many elements go into a risk assessment, and each of those elements represent a possible source of uncertainty or bias that will influence the end result. There are also challenges in obtaining accurate and useful data on MMOD-related failures.

Squire, Michael↗
NASA NTRS2022

Run Time Assurance for Electric Vertical Takeoff and Landing Aircraft

NASA is conducting research to demonstrate and evaluate the application of Run Time Assurance (RTA) as a means to assure safety in Electric Vertical Takeoff and Landing (eVTOL) aircraft with highly automated or autonomous flight capability supervised by a single onboard pilot. The work described in this report demonstrates an application of RTA and examines the implications for design and analysis of aircraft functions and systems; aircraft safety hazards; safety assurance; development assurance; and pilot tasks and performance. This research effort also seeks to assess the efficacy of the combined application of traditional Functional Hazard Analysis (FHA) and the more modern System Theoretic Process Analysis (STPA) techniques to perform hazard analyses on aircraft with complex automated and autonomous systems and an onboard pilot. During the research effort we developed architectural designs of two alternate eVTOL aircraft, generally following the process characterized in the SAE standards ARP4754 and ARP4761. The design has focused on the control architectures of these aircraft, which are identical except that one incorporates RTA techniques to reduce the criticality of some key software components. Artifacts of this process include a taxonomy of aircraft-level functions, aircraft-level architecture diagrams, aircraft-level functional hazard assessments (AFHA), function allocations onto aircraft systems and subsystems, functional block diagrams for a select set of control-related functions, and system-level functional hazard assessments (SFHA) for those functions. This project has highlighted the notion that DAL D is something of a sweet spot for low-confidence controllers in an RTA-based design. Among the many activities described in DO-178C, the activities related to requirement verifiability, algorithmic accuracy, and test coverage can be the most challenging for the kinds of advanced control techniques that may be desirable in novel UAM designs, such as adaptive control, machine-learning, artificial intelligence, numerical search, and Monte Carlo based algorithms. Moreover, the standard requires that development teams demonstrate that errors leading to unacceptable failure conditions have been removed from the software. The RTA architecture, which cordons off the low-confidence function, makes it much easier to show this for these kinds of algorithms. With regard to the use of STPA and FHA as complementary hazard analysis techniques, our research effort led us to the conclusion that STPA should be used to derive requirements for hardware and software systems and/or components. Also, STPA is a natural complement to other processes in ARP4754A involving design studies and iteration.

Run-time assurance↗
NASA NTRS2024

Pick-and-Eat Space Crop Production Flight Testing on the International Space Station

Fresh, nutritious, palatable produce for crew consumption on long-duration spaceflight missions may provide health-promoting, bioavailable nutrients and enhance the dietary experience. VEG-04A and VEG-04B explored growing leafy greens on the International Space Station using the Veggie Vegetable Production System. Two flight tests with ground controls were conducted in 2019 growing mizuna mustard, where Veggie chambers were set to different red-to-blue-to-green light formulations. Light quality affects plant growth, nutrition, microbiology, and organoleptic characteristics on Earth, and we examined how these vary in microgravity and under different harvest scenarios. Astronauts harvested and weighed mizuna and completed organoleptic evaluations. Flight samples were returned to Earth for nutritional quality and microbial food safety analyses. Yield and chemistry differed between ground and flight samples and light treatments, and bacterial and fungal counts were lower in ground than in flight samples. This research helps increase our understanding of the requirements for growing high-quality crops in spaceflight.

Food Safety, International Space Station, Nutritio↗
NASA NTRSDate not supplied

Predictive Efficiency Modeling for Lithium-Ion Cells at Various Relative Charge and Discharge C Rates for Electrified Powertrain Flight Demonstration

The Electrified Powertrain Flight Demonstration (EPFD) project aims to enhance battery efficiency by studying various Lithium-Ion (Li-ion) cell types. These cells are analyzed under different charging and discharging rates (C rates) to simulate a range of scenarios. As the EPFD project focuses on developing a sustainable hybrid/electric aircraft, it is essential to evaluate the efficiency, energy density, and weight of various battery cells. This ensures safety, reliability and optimal travel distance of the aircraft.

Battery↗
NASA NTRS2004

Flight Simulator Evaluation of Display Media Devices for Synthetic Vision Concepts

The Synthetic Vision Systems (SVS) Project of the National Aeronautics and Space Administration's (NASA) Aviation Safety Program (AvSP) is striving to eliminate poor visibility as a causal factor in aircraft accidents as well as enhance operational capabilities of all aircraft. To accomplish these safety and capacity improvements, the SVS concept is designed to provide a clear view of the world around the aircraft through the display of computer-generated imagery derived from an onboard database of terrain, obstacle, and airport information. Display media devices with which to implement SVS technology that have been evaluated so far within the Project include fixed field of view head up displays and head down Primary Flight Displays with pilot-selectable field of view. A simulation experiment was conducted comparing these display devices to a fixed field of view, unlimited field of regard, full color Helmet-Mounted Display system. Subject pilots flew a visual circling maneuver in IMC at a terrain-challenged airport. The data collected for this experiment is compared to past SVS research studies.

Arthur, J. J., III↗
NASA NTRS2002

Technical Interchange Meeting Guidelines Breakout

Along with concept developers, the Systems Evaluation and Assessment (SEA) sub-element of VAMS will develop those scenarios and metrics required for testing the new concepts that reside within the System-Level Integrated Concepts (SLIC) sub-element in the VAMS project. These concepts will come from the NRA process, space act agreements, a university group, and other NASA researchers. The emphasis of those concepts is to increase capacity while at least maintaining the current safety level. The concept providers will initially develop their own scenarios and metrics for self-evaluation. In about a year, the SEA sub-element will become responsible for conducting initial evaluations of the concepts using a common scenario and metric set. This set may derive many components from the scenarios and metrics used by the concept providers. Ultimately, the common scenario\metric set will be used to help determine the most feasible and beneficial concepts. A set of 15 questions and issues, discussed below, pertaining to the scenario and metric set, and its use for assessing concepts, was submitted by the SEA sub-element for consideration during the breakout session. The questions were divided among the three breakout groups. Each breakout group deliberated on its set of questions and provided a report on its discussion.

Fong, Rob↗
NASA NTRS1993

Postflight hardware evaluation 360T025 (RSRM-25, STS-46)

The final report for the Clearfield disassembly evaluation and a continuation of the KSC postflight assessment for the 360T025 (STS-46) Redesign Solid Rocket Motor (RSRM) flight set is presented. All observed hardware conditions were documented on PFOR's and are included in Appendices A through C. Appendices D and E contain the measurements and safety factor data for the nozzle and insulation components. Along with the KSC Ten-Day Postflight Hardware Evaluation Report (TWR-60687), a summary of the 360T025 hardware evaluation is provided. The as-flown hardware configuration is documented in TWR-60470. Disassembly evaluation photograph numbers are logged in TWA-1986. The 360T025 flight set disassembly evaluations described were performed at the RSRM Refurbishment Facility in Clearfield, Utah. The final factory joint demate occurred on 16 Mar. 1993. Detailed evaluations were performed in accordance with the Clearfield PEEP, TWR-50051, Revision A. All observations were compared against limits that are also defined in the PEEP. These limits outline the criteria for categorizing the observations as acceptable, reportable, or critical. Hardware conditions that were unexpected and/or determined to be reportable or critical were evaluated by the applicable CPT and tracked through the PFAR system.

Morgan, Ferral↗