Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “room temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

An approach for the measurement of the bulk temperature of single crystal diamond using an X-ray Free Electron Laser

We present a method to determine the bulk temperature of a single crystal diamond sample at an X-Ray Free Electron Laser using inelastic X-ray scattering. The experiment was performed at the High Energy Density (HED) instrument at the European XFEL GmbH, Germany. The technique, based on inelastic X-ray scattering and the principle of detailed balance, was demonstrated to give accurate temperature measurements, within 8% for both room temperature diamond and heated diamond to 500 K. Here, the temperature was increased in a controlled way using a resistive heater to test theoretical predictions of the scaling of the signal with temperature. The method was tested by validating the energy of the phonon modes with previous measurements made at room temperature using inelastic X-ray scattering and neutron scattering techniques. This technique could be used to determine the bulk temperature in transient systems with a temporal resolution of 50 fs and for which accurate measurements of thermodynamic properties are vital to build accurate equation of state models.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Compatibility of Fe-Cr-Al and Fe-Cr-Al-Mo oxide dispersion strengthened steels with static liquid sodium at 700 °C

We report the corrosion behavior and tensile properties of oxide dispersion strengthened (ODS) FeCr, FeCrAl, FeCrAlMo steels and 316H stainless steel were evaluated after 1000 h at 700 °C in static sodium with and without an oxygen getter (Zr foil). Without Zr foil to getter the dissolved oxygen in the liquid sodium, combined oxidation (formation of Cr, Fe-rich or Al-rich oxides) and dissolution of the studied materials was observed. For the ODS FeCr, Cr- and Fe-rich oxide formation and dissolution induced Cr depletion in the underlying alloy and led to the formation of laves phases that were observed to be detrimental to the room temperature tensile properties. For ODS FeCrAlMo and FeCrAl Al-rich oxide formation and dissolution resulted in Al depletion in the underlying alloys but did not impact tensile properties at room temperature. For 316H temperature induced sensitization combined with oxidation decreased room temperature tensile properties. With Zr foil added as oxygen getter, roughened surfaces and Al depletion profiles suggested the dissolution of ODS FeCr and FeCrAl into the liquid sodium while limited dissolution was observed for ODS FeCrAlMo and 316H. For the 316H and ODS FeCrAlMo steels, precipitates were formed at the grain boundaries after exposure. Tensile properties of ODS FeCr, FeCrAl and FeCrAlMo were not affected by the 1000 h corrosion exposure with Zr foil added to the sodium but for 316H temperature-induced grain boundary sensitization negatively affected the tensile properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Site‐selective fluorescence and spectroscopic properties of Yb‐doped lanthanum titanate glasses

Abstract Ytterbium‐doped lanthanum titanate glasses were prepared by levitation melting for the detailed characterization of the spectroscopic properties in the rare‐earth titanate glass host. Low‐temperature fluorescence spectroscopy reveals distinct site‐selectivity in both static and lifetime fluorescence measurements suggesting an absence of clustering as well as significant variation of local ytterbium environments. Typical site‐selectivity behavior of a shrinking Stark manifold with lower excitation energy is observed. At 77 K, both the mean emission frequency and the fluorescence lifetime initially increase as the excitation energy decreases from about 11100 to 10750 and then slightly decrease at lower excitation energy. Temperature‐dependent lifetime measurements between 77 and 420 K show a decreasing lifetime with increasing temperature and are well described by a two‐level thermal activation model. The temperature‐dependent fluorescence spectroscopy coupled with a room temperature white light absorption measurement allow the determination of the Stark energy levels of in lanthanum titanate glass as well as the calculation of the laser cross‐sections.

Materials Science↗
DOE OSTI2024

Size resolved particle volatility for 30, 60, and 90 nm particles collected at the EPCAPE Mount Soledad site from 04/23/2023 to 06/15/2023

VTDMA GF-PDF: Growth factor probability density functions from the Gysel inversion are located here, where probability is out of 200. The instrument measured three different diameters 30 nm, 60nm and 90nm each diameter was selected for an hour. During that hour three different temperatures where scanned (40°C, 80°C, 160°C) in between each temperature a bypass scan was taken at room temperature. Each scan took 10-minutes and scanned growth factors from 0.2-1.2. Calibrations of the instrument with NaCl were performed on 4/26/2023 from 11:20 to 14:20, on 5/16/2023 from 11:40 to 16:00, and on 5/30/2023 from 10:20 to 14:20. Calibrations with (NH4)2SO4 were performed on 5/8/2023 from 11:45 to 14:40, on 5/23/2023 from 11:20 to 3:00, and on 6/14/2023 from 13:00 to 16:00. Time is recorded in seconds since 1/1/1904. GF_Vol_avg: Growth factor volume average calculated by the Gysel inversion. The instrument measured three different diameters 30 nm, 60nm and 90nm each diameter was selected for an hour. During that hour three different temperatures where scanned (40°C, 80°C, 160°C) in between each temperature a bypass scan was taken at room temperature. Each scan took 10-minutes and scanned growth factors from 0.2-1.2. Calibrations of the instrument with NaCl were performed on 4/26/2023 from 11:20 to 14:20, on 5/16/2023 from 11:40 to 16:00, and on 5/30/2023 from 10:20 to 14:20. Calibrations with (NH4)2SO4 were performed on 5/8/2023 from 11:45 to 14:40, on 5/23/2023 from 11:20 to 3:00, and on 6/14/2023 from 13:00 to 16:00. Time is recorded in seconds since 1/1/1904.

30nm growth factor volume average at 160C (GF_vol_↗
DOE OSTI2023

Intrinsic Berry curvature driven anomalous Nernst thermopower in the semimetallic Heusler alloy CoFeVSb

Understanding of spin-heat coupling mechanisms and magnetothermoelectric phenomena, including the anomalous Nernst effect (ANE), in emergent quaternary Heusler alloys is of practical importance for applications in thermal management and energy harvesting. Here, we demonstrate an intrinsic Berry curvature mediated anomalous Nernst thermopower in CoFeVSb, which orders magnetically at high temperature ( T C ≈ 850 K ) with a large saturation magnetization of ≈ 2.2 μ B / f . u . at room temperature. We show that the electron-electron elastic and electron-magnon inelastic scattering dominate longitudinal electrical transport at low temperatures ( T ≤ 50 K ), whereas the electron-phonon and electron-magnon scatterings govern it at higher T . The longitudinal thermopower is resulted mainly from the diffusive contribution with a very large longitudinal Seebeck coefficient ( 42 μ V K - 1 at 395 K). The value of the anomalous Nernst coefficient ( S ANE ) for CoFeVSb at room temperature is 0.039 μ V K - 1 which is higher than the compressively strained SrRu O 3 film ( 0.03 μ V K - 1 ) as well as the spin gapless semiconductor CoFeCrGa ( 0.018 μ V K - 1 ). On lowering T , both the ordinary Nernst coefficient and carrier mobility increase but an opposite trend is found for S ANE . Our ab initio simulations reveal the topological semimetallic nature of CoFeVSb with a pair of Weyl points. These Weyl crossings result in a significant contribution to the Berry curvature, leading to an intrinsic anomalous Hall conductivity ( σ x y AHE ) of ≈ 85 S/cm, which matches well with experiment (77 S/cm at 2 K). Our experimental findings and ab initio calculations support the dominance of the intrinsic Berry curvature in the observed ANE. The ratio of σ x y AHE to the transverse anomalous thermoelectric conductivity ( α x y ANE ) shows an increasing trend with T attaining a sizable fraction of k B e ( ≈ 0.35 k B e ) at room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Depth-Dependent Understanding of Cathode Electrolyte Interphase (CEI) on the Layered Li-Ion Cathodes Operated at Extreme High Temperature

The high-temperature operation of Li-ion batteries is highly dependent on the stability of the cathode electrolyte interphase (CEI) formed during lithiation-delithiation reactions. However, knowledge on the nature of the CEI is limited and its stability under extreme temperatures is not well understood. Therefore, herein, we investigate a proof-of-concept study on stabilizing CEI on model LiNi 0.33 Mn 0.33 Co 0.33 O 2 (NMC333) at extreme operation condition of 100 oC using thermally stable pyrrolidinium based ionic liquid electrolyte. The electrochemical lithiation-delithiation reactions at 100 oC and the CEI evolution upon different cycling conditions are investigated. Further, the depth-dependent CEI chemistry was investigated using energy tunable synchrotron-based hard X-ray photoelectron spectroscopy (HAXPES). Overall, the results reveal that the high temperature operation accelerated the CEI formation compared to room temperature, and the surface of the interphase layer is rich in boron-based inorganic moieties than the deeper surface. Further, bulk sensitive X-ray absorption spectroscopy (XAS) was used to investigate the transition metal redox contributors during high temperature electrochemical reactions, similar to room temperature, the Ni2+/4+redox couple is the only charge compensating redox couple during high temperature operation. Finally, the physical nature of the conformal CEI on the cathode particles was visualized with high-resolution transmission electron microscopy, which confirms that the significant degradation of cathode particles without conformal CEI is due to the transformation of layer to spinel formation at extreme temperature. In this study, understanding this high temperature interfacial chemistry of NMC cathodes through advanced spectroscopy and microscopy will shed light on transforming ambient temperature Li-ion chemistry to high temperature applications.

25 ENERGY STORAGE↗
DOE OSTI2020

Insights into the Transformation-Induced Plasticity (TRIP) Effect in Ti-Free Grade 300 Maraging Steel Manufactured by Laser Powder Bed Fusion (LPBF)

The near-net fabrication capabilities of laser powder-bed fusion (LPBF) offer the potential to manufacture tools with complex cooling channels that can improve the production efficiency of the tools with reduced greenhouse gas emissions. High strength, toughness, and wear resistance are some of the key properties required by the tooling industries to qualify tools. While strength can be increased through appropriate heat treatments, the increase in strength comes with an associated ductility loss. Here, we show that the non-equilibrium conditions inherent to LPBF can suppress the transformation-induced plasticity effect to room temperature in a Ti-free version of grade 300 maraging steel (G300MS), which is commonly not observed at room temperature in G300MS manufactured using conventional methods. The presence of retained austenite along with Ni-rich regions was found to increase the kinetics for austenite reversion during aging, thereby enabling the transformation of austenite into ε martensite during tensile deformation at room temperature, in turn increasing the strength with minimal ductility loss.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Halide Perovskites Breathe Too: The Iodide–Iodine Equilibrium and Self-Doping in Cs 2 SnI 6

The response of an oxide crystal to the atmosphere can be personified as breathing-a dynamic equilibrium between O 2 gas and O 2– anions in the solid. We characterize the analogous defect reaction in an iodide double-perovskite semiconductor, Cs 2 SnI 6 . Here, I 2 gas is released from the crystal at room temperature, forming iodine vacancies. The iodine vacancy defect is a shallow electron donor and is therefore ionized at room temperature; thus, the loss of I2 is accompanied by spontaneous n-type self-doping. Conversely, at high I 2 pressures, I 2 gas is resorbed by the perovskite, consuming excess electrons as I 2 is converted to 2I – . Halide mobility and irreversible halide loss or exchange reactions have been studied extensively in halide perovskites. However, the reversible exchange equilibrium between iodide and iodine [2I – (s) ↔ I 2(g) + 2e – ] described here has often been overlooked in prior studies, though it is likely general to halide perovskites and operative near room temperature, even in the dark. An analysis of the 2I – (s) /I 2(g) equilibrium thermodynamics and related transport kinetics in single crystals of Cs 2 SnI 6 therefore provides insight toward achieving stable composition and electronic properties in the large family of iodide perovskite semiconductors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Nafion Passivation of c-Si Surface and Edge for Electron Paramagnetic Resonance

Effective surface passivation of crystalline silicon (c-Si) surface by reducing the carrier recombination rate has led to modern c-Si solar cells with efficiencies > 25% in both laboratory and industrial settings. Typical mainstream surface passivation techniques include high-temperature silicon oxide (SiOx), amorphous silicon (a-Si:H), hydrogen-rich silicon nitride (SiNx), and aluminum oxide (Al2O3) [1]. They have demonstrated excellent surface recombination velocity of < 1 cm/s owing to both chemical passivation (via the hydrogen saturation of Si dangling bonds at the c-Si surface), and field-effect passivation (via the band bending from the fixed charge of the dielectric layers). Recently, several groups have studied solution-based organic materials for c-Si passivation, including bis(trifluoromethane)sulfonimide (TFSI), polystyrenesulfonate, and Nafion [2, 3] via spin or dip coating. All films were processed at ambient room temperature, and a high lifetime of 12 ms, as well as a low saturation current density (J0) of 16 fA/cm2, have been demonstrated using Nafion passivation [2]. However, despite the air instability, Nafion has several advantages when introduced to PV applications: (a) Wafer quality can be measured at high throughput after several process stages. (b) It is compatible with PL mapping, compared to HF liquid passivation which cannot be performed in room ambient. (c) Nafion process is fast and poses fewer constraints on process complexity, and cleanness, compared to Al2O3 and a-Si:H passivation. (d) Nafion is the ideal room temperature passivation, which can be applied onto a small fragment of a degraded module to investigate microscopic mechanisms when studying degradation mechanisms. Edge passivation is needed for advanced characterization tests such as Electron Paramagnetic Resonance (EPR), Electrically Detected Magnetic Resonance (EDMR), Deep Level Transient Spectroscopy (DLTS), local cell current-voltage (J-V), and Suns-Voc. In such cases, the laser-damaged minicell edges will obscure the true degradation mechanisms, and Nafion can effectively passivate them without causing further degradation through elevated-temperature processes. In this contribution, we show the passivation results of Nafion on bare nCz and compare it with a Al2O3 witness. We highlight the importance of edge pre-treatment before Nafion to achieve good passivation. We show that Nafion can reach decent passivation without undergoing high-temperature processes. We also explore the temperature dependency of Nafion through photoluminescence (PL) study and demonstrate the application of Nafion under cryogenic temperature (~6 K) through EPR. Our results reveal that Nafion can reduce surface and edge Si dangling bonds at low temperatures. Thus, it can be used as an effective room temperature passivation technique for advanced characterization methods.

c-Si↗
DOE OSTI2023

A reduced-order modeling of a tubular solar reactor for long duration thermochemical energy storage

The storage of solar energy in a solid form, referred to as a “solar fuel”, can be achieved through a process known as endothermic solar thermochemistry. This process transforms the absorbed solar energy into a stable and retrievable form that can be stored for extended periods of time. This paper presents a low–order heat transfer model of a counter–current tubular falling bed reactor designed to produce thermally reduced magnesium manganese oxide pellets for long duration thermochemical energy storage. The energy required for the endothermic reduction was supplied by concentrated solar energy or renewable electricity via indirect heating of the gas and solid reactants flowing in a ceramic tube. The counter-current gas flow enhances the mixing of the solid particles with the heat recuperation zone, allowing the gas and particles to enter and exit the tubular reactor close to room temperature. Further, the reactor was vertically oriented and was heated circumferentially by an adjustable level heat flux along a finite segment of its length. The temperature distribution of the reactor in response to transient changes along the tube was modeled by considering conduction, convection, and radiation heat transfer. Governing equations for the heat transfer model were solved by discretizing the reactor tube into a finite number of control volumes and using an energy balance for the heat exchange between the reactor wall, gas, and particles within the control volume. The energy absorbed during this endothermic reaction was modeled numerically by fitting the data of the chemical conversion rate with the corresponding temperature of particles in the heating zone. The numerical model has been experimentally validated using a reactor prototype made of a 121.92 cm alumina tube heated by a 7kW electric tube–furnace. The alumina tube receives magnesium manganese oxide pellets of 3.66±0.516 mm in diameter from the top, and a counter–current gas flow from the bottom. The reactor wall temperature was monitored by six thermocouples installed along the reactor tube length. The experimental procedure was numerically simulated, and the temperature variation along the reactor tube was compared with a matrix of experimental runs for a range of particles mass flowrates (0.75–1.25g/s) and corresponding gas flowrates (36–65 SLPM). The reactor system was heated gradually from room temperature to a steady state temperature of 1673K, and then cooled down to room temperature. The heating and cooling processes were simulated, and the numerical and experimental results were compared throughout processes. The numerical model showed similar trends to the experimental results, with an error of 0.69 to 7.9% for the particle inlet and 0.7 to 7.9% for the gas inlet during steady-state operation. The proposed numerical model can be implemented as a simplified physical model to design a feedback control system to regulate reactor temperature.

14 SOLAR ENERGY↗
DOE OSTI2024

Self-compensation of group-V acceptors in CdTe

Cadmium Telluride is at the core of an important thin-film technology for photovoltaics that is already commercially available, yet the CdTe-based solar cell efficiency remains limited at 22%, well below the theoretical limit of ~30%. Increasing the hole concentration is crucial for higher efficiency, and group-V elements such as As, P, and Sb are potential dopants as they are shallow acceptors. Nevertheless, group-V doped p-type CdTe often exhibits low doping activation, and the compensation source remains debated. Here, we performed hybrid density functional calculations with spin-orbit coupling to investigate possible sources of hole compensation in group-V doped CdTe. First, regarding possible self-compensation of the group-V dopants, we find that the formation of AX centers is unlikely since they are found to be unstable relative to the shallow acceptor forms. However, if the group-V dopants come in during growth (such as dimer molecules As2, P2, and Sb2), we find that the impurity atoms, which would occupy nearest neighbor sites, maintain the V-V bonds, limiting the hole density. For the native defects, our study reveals that Cd interstitial is the lowest energy donor defect in p-type CdTe. Still, it has a small migration barrier of 0.5 eV, making it highly mobile and unstable at room temperature. The Te vacancy is the next lowest formation energy donor. The migration barrier of 1.4 eV indicates that the Te vacancy is stable at room temperature. The antisite CdTe is also a donor, with low formation energy and stable at room temperature, potentially limiting the hole concentration. Our results, therefore, shed light on possible compensation centers and some guidance on how to avoid them.

14 SOLAR ENERGY↗
DOE OSTI2026

Design of a double-sided laser heating compatible piezoelectrically driven dynamic diamond anvil cell

Piezoelectrically driven dynamic diamond anvil cells are generally limited to use at room temperature due to spatial conflicts with the optical components necessary for double-sided laser heating. Here, this work describes the design of a double-sided laser-heating-compatible, piezoelectrically driven dynamic diamond anvil cell (LH-dDAC) that expands the range of experimentally accessible compression rate/temperature space. By developing a spatially in-parallel design, in which the diamond anvils and the piezo actuators lie alongside each other, the total length of the apparatus is reduced to 66.5 mm. The new LH-dDAC is capable of probing both overpressure and compression-rate effects on the kinetics of phase transitions. We illustrate the capability of the new LH-dDAC using the following cases: (1) a simultaneous pressure and temperature jump from 19.5 GPa and room temperature to 40 GPa and ≈1550 K and (2) a controlled compression ramp at ≈1850 K and ≈100 GPa/s. By pairing rapid compression with laser heating, the new LH-dDAC opens the door to studies of diffusionally controlled transformations at high pressures and temperatures.

Copley, J. A. [Princeton Univ., NJ (United States)↗
DOE OSTI2020

Mechanical testing of PH13-8Mo H950 Steel for Xue-Wierzbicki Fracture Criterion Determination at 20° C and -40° C

Mechanical testing was conducted to collect the data needed to build a Xue-Wierzbicki (XW) fracture model for PH13-8 Mo H950 stainless steel (PH 13-8 SS). This model is intended for use in structural analysis of this material between room temperature and -40° C. Tests were performed on four different specimen geometries such that a range of stress states were characterized at room temperature and -40° C. Tensile tests on R5 tensile specimens were also performed to assess material anisotropy. Fracture toughness test were also conducted. The fracture toughness of this material at -40° C was 68% of the room-temperature value. Material strength generally increased with decreasing temperature while the opposite trend was observed for ductility. These trends were most pronounced for specimens with the largest stress triaxialities.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructure and high temperature tensile properties of 316L fabricated by laser powder-bed fusion

316L stainless steel fabricated by laser powder-bed fusion (LPBF) has attracted significant attention due to a unique combination of strength and ductility at room temperature. Understanding of high temperature tensile properties of LPBF fabricated 316L is, however, limited. In the present investigation, tensile testing was conducted at 20–700ºC on LPBF 316L in as printed condition and after annealing for 5 h at 500–800ºC. Room temperature data confirmed the excellent ductility of the LPBF-processed 316L steel due to the cellular structure with high dislocation density. However, a significant decrease in ductility was observed at temperatures above 200ºC. These results are consistent with a change of deformation mechanisms observed in wrought 316L, with twinning playing a key role at room temperature. Finally, microstructure characterization and tensile testing revealed that the cellular structure is stable up to 500ºC, but a decrease of yield strength was observed at temperatures above 600ºC likely due to a decrease in dislocation density via annealing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Anharmonic theory of superconductivity in the high-pressure materials

Electron-phonon superconductors at high pressures have displayed the highest values of critical superconducting temperature Tc on record, now rapidly approaching room temperature. Despite the importance of high-P superconductivity in the quest for room-temperature superconductors, a mechanistic understanding of the effect of pressure and its complex interplay with phonon anharmonicity and superconductivity is missing, as numerical simulations can bring only system-specific details, clouding out key players controlling the physics. In this work, we develop a minimal model of electron-phonon superconductivity under an applied pressure which takes into account the anharmonic decoherence of the optical phonons. We find that T c behaves nonmonotonically as a function of the ratio Γ/ω 0 , where Γ is the optical phonon damping and ω 0 is the optical phonon energy at zero pressure and momentum. Optimal pairing occurs for a critical ratio Γ/ω 0 when the phonons are on the verge of decoherence (“diffusonlike” limit). Our framework gives insights into recent experimental observations of T c as a function of pressure in the complex BCS material TlInTe 2 .

36 MATERIALS SCIENCE↗
DOE OSTI2023

Probing the Electronic and Opto-Electronic Properties of Multilayer MoS 2 Field-Effect Transistors at Low Temperatures

Transition metal dichalcogenides (TMDs)-based field-effect transistors (FETs) are being investigated vigorously for their promising applications in optoelectronics. Despite the high optical response reported in the literature, most of them are studied at room temperature. To extend the application of these materials in a photodetector, particularly at a low temperature, detailed understanding of the photo response behavior of these materials at low temperatures is crucial. Here we present a systematic investigation of temperature-dependent electronic and optoelectronic properties of few-layers MoS 2 FETs, synthesized using the mechanical exfoliation of bulk MoS 2 crystal, on the Si/SiO 2 substrate. Our MoS 2 FET show a room-temperature field-effect mobility μ FE ~40 cm 2 ·V -1 ·s -1 , which increases with decreasing temperature, stabilizing at 80 cm 2 ·V -1 ·s -1 below 100 K. The temperature-dependent (50 K < T < 300 K) photoconductivity measurements were investigated using a continuous laser source λ = 658 nm (E = 1.88 eV) over a broad range of effective illuminating laser intensity, P eff (0.02 μW < P eff < 0.6 μW). Photoconductivity measurements indicate a fractional power dependence of the steady-state photocurrent. The room-temperature photoresponsivity (R) obtained in these samples was found to be ~2 AW -1 , and it increases as a function of decreasing temperature, reaching a maximum at T = 75 K. The optoelectronic properties of MoS 2 at a low temperature give an insight into photocurrent generation mechanisms, which will help in altering/improving the performance of TMD-based devices for various applications.

2D materials↗
DOE OSTI2020

Thermally Activated Adsorption in Metal–Organic Frameworks with a Temperature‐Tunable Diffusion Barrier Layer

Abstract Modification of the external surfaces of metal–organic frameworks offers a new level of control over their adsorption behavior. It was previously shown that capping of MOFs with ethylenediamine (EDA) can effectively retain small gaseous molecules at room temperature. Reported here is a temperature‐induced variation in the capping‐layer gate‐opening mechanism through a combination of in situ infared experiments and ab initio simulations of the capping layer. An atypical acceleration and increase in the loading of weakly adsorbed molecules upon raising the temperature above room temperature is observed. These findings show the discovery of novel temperature‐dependent kinetics that goes beyond standard kinetics and suggest a new avenue for tailoring selective adsorption by thermally tuning the surface barrier.

Tan, Kui↗
DOE OSTI2020

Thermally activated adsorption in metal–organic frameworks with a temperature–tunable diffusion barrier layer

Modification of the external surfaces of metal organic frameworks offers a new level of control over their adsorption behavior. Here, we have previously shown that capping of MOFs with ethylenediamine (EDA) can effectively retain small gaseous molecules at room temperature. Here, we report a temperature–induced variation in the capping–layer gate opening mechanism through a combination of in situ IR experiments and ab initio simulations of the capping layer. We find an atypical acceleration and increase in the loading of weakly adsorbed molecules upon raising the temperature above room temperature. Our findings show the discovery of a novel temperature–dependent kinetics that goes beyond standard kinetics and suggest a new avenue for tailoring selective adsorption by thermally tuning the surface barrier.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗