Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “quantum mechanical systems and processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

556 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Ultrafast carrier dynamics in terahertz photoconductors and photomixers: beyond short-carrier-lifetime semiconductors

Abstract Efficient terahertz generation and detection are a key prerequisite for high performance terahertz systems. Major advancements in realizing efficient terahertz emitters and detectors were enabled through photonics-driven semiconductor devices, thanks to the extremely wide bandwidth available at optical frequencies. Through the efficient generation and ultrafast transport of charge carriers within a photo-absorbing semiconductor material, terahertz frequency components are created from the mixing products of the optical frequency components that drive the terahertz device – a process usually referred to as photomixing. The created terahertz frequency components, which are in the physical form of oscillating carrier concentrations, can feed a terahertz antenna and get radiated in case of a terahertz emitter, or mix with an incoming terahertz wave to down-convert to DC or to a low frequency photocurrent in case of a terahertz detector. Realizing terahertz photoconductors typically relies on short-carrier-lifetime semiconductors as the photo-absorbing material, where photocarriers are quickly trapped within one picosecond or less after generation, leading to ultrafast carrier dynamics that facilitates high-frequency device operation. However, while enabling broadband operation, a sub-picosecond lifetime of the photocarriers results in a substantial loss of photoconductive gain and optical responsivity. In addition, growth of short-carrier-lifetime semiconductors in many cases relies on the use of rare elements and non-standard processes with limited accessibility. Therefore, there is a strong motivation to explore and develop alternative techniques for realizing terahertz photomixers that do not rely on these defect-introduced short-carrier-lifetime semiconductors. This review will provide an overview of several promising approaches to realize terahertz emitters and detectors without short-carrier-lifetime semiconductors. These novel approaches utilize p-i-n diode junctions, plasmonic nanostructures, ultrafast spintronics, and low-dimensional materials to offer ultrafast carrier response. These innovative directions have great potentials for extending the applicability and accessibility of the terahertz spectrum for a wide range of applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

ORNL_AISD_NiPt_108atoms

This dataset describes the nickel-platinum (NiPt) solid solution binary alloy, where the two constituent elements nickel (Ni) and platinum (Pt) are randomly placed on the face centered cubic (FCC) crystal structure, with the lattice constant of 3.840 angstroms. The dataset comprises data for crystal structures with 108 atoms with 1,900 configurations. The data set was generated for concentrations ranging from 0at% of Pt to 100at% of Pt in the NiPt binary system, with increasing the concentration of Pt in the system every 5at%. For each one of the chemical compositions, 100 random configurations were generated, each with a different random seed. Each of the output files contains the mass, type, atomic coordinates, energy per atom, and forces in x, y, and z directions respectively. For each atomic configuration, the output was collected every 150 steps during the minimization stage and every 1000 steps during the replica exchange stage. Large-scale Atomic/Molecular Massively Parallel Simulator (LAMMPS) [1], which is a molecular dynamics code, was used to generate data for NiPt alloy. The simulation used the interatomic potential for NiPt binary system 'MEAM_LAMMPS_KimSeolJi_2017_PtNi__MO_020840179467_001' [3] from the OpenKIM library (Open Knowledgebase of Interatomic Models) [2]. This potential was developed based on the second nearest-neighbor modified embedded-atom method (2NN MEAM). The simulation process begins with the generation of the random NiPt structure and follows with the short minimization and replica exchange simulation. The minimization procedure adjusts atomic coordinates and performs energy minimization, which typically leads to a local potential energy minimum. The method used for the minimization was the conjugate gradient algorithm. A short replica exchange (parallel tempering) simulation involves four replicas (ensembles) of a system and follows the minimization stage. Multiple snapshots of the configuration were collected during the minimization and replica exchange stages. NiPt alloy is interesting due to its magnetic and charge transfer properties [4]. The data is provided in a compressed zipped folders atoms108.zip. The zipped folder contains the data structured in the following way: - Ni_ground_state.cfg --> atomic configuration for the pure nickel - Pt_ground_state.cfg --> atomic configuration for the pure platinum - Pt#_filtered --> folders containing atomic configurations for #at% concentration of platinum. The folder contains 100 atomic configurations, each saved in a subfolder - Each subfolder named config* is associated with a specific atomic configuration. Each of these subfolders contains files with .cfg format, corresponding to outputs for each atomic configuration The total number of atomic configurations contained in atoms108.zip is 66,132. This dataset is an extension to the dataset ORNL_AISD_NiPt [5] that has been previously released with crystal structures of 256 atoms, 864 atoms, and 2,048 atoms, with the same methodology for data collection. References [1] https://www.lammps.org/ [2] https://openkim.org/ [3] https://openkim.org/id/MEAM_LAMMPS_KimSeolJi_2017_PtNi__MO_020840179467_001 [4] El-Gendy, Ahmed A. and Hampel, Silke and Büchner, Bernd and Klingeler, Rüdiger, Tuneable magnetic properties of carbon-shielded NiPt-nanoalloys, RSC Adv., volume 6, issue 57, pages 52427-52433, 2016, The Royal Society of Chemistry, doi:10.1039/C6RA05910D [5] M. Karabin, M. Lupo Pasini, and M. Eisenbach. ORNL_AISD_NiPt. United States: N. p., 2023. Web. doi:10.13139/OLCF/1958172.

36 MATERIALS SCIENCE↗
DOE OSTI2023

ORNL_AISD_NiPt

This dataset describes the nickel-platinum (NiPt) solid solution binary alloy, where the two constituent elements nickel (Ni) and platinum (Pt) are randomly placed on the face centered cubic (FCC) crystal structure, with the lattice constant of 3.840 angstroms. The dataset comprises data for three different sizes of the crystal structure: 256 atoms, 864 atoms, and 2,048 atoms, each of which contains 1900 configurations. For each size of the crystal structure, the data set was generated for concentrations ranging from 0at% of Pt to 100at% of Pt in the NiPt binary system, with increasing the concentration of Pt in the system every 5at%. For each one of the chemical compositions, 100 random configurations were generated, each with a different random seed. Each of the output files contains the mass, type, atomic coordinates, energy per atom, and forces in x, y, and z directions respectively. For each atomic configuration, the output was collected every 150 steps during the minimization stage and every 1000 steps during the replica exchange stage. Large-scale Atomic/Molecular Massively Parallel Simulator (LAMMPS) [1], which is a molecular dynamics code, was used to generate data for NiPt alloy. The simulation used the interatomic potential for NiPt binary system MEAM_LAMMPS_KimSeolJi_2017_PtNi__MO_020840179467_001 [3] from the OpenKIM library (Open Knowledgebase of Interatomic Models) [2]. This potential was developed based on the second nearest-neighbor modified embedded-atom method (2NN MEAM). The simulation process begins with the generation of the random NiPt structure and follows with the short minimization and replica exchange simulation. The minimization procedure adjusts atomic coordinates and performs energy minimization, which typically leads to a local potential energy minimum. The method used for the minimization was the conjugate gradient algorithm. A short replica exchange (parallel tempering) simulation involves four replicas (ensembles) of a system and follows the minimization stage. Multiple snapshots of the configuration were collected during the minimization and replica exchange stages. NiPt alloy is interesting due to its magnetic and charge transfer properties [4]. The data is provided in three compressed zipped folders: atoms256.zip, atoms864.zip, atoms2048.zip Each zipped folder contains the data that describes crystals of size 256 atoms, 864 atoms, and 2,048 atoms respectively. Each one of the three zipped folders contains the data structured in the following way: -Ni_ground_state.cfg --> atomic configuration for the pure nickel -Pt_ground_state.cfg --> atomic configuration for the pure platinum -Pt#_filtered --> folders containing atomic configurations for #at% concentration of platinum. The folder contains 100 atomic configurations, each saved in a subfolder. Each subfolder named config* is associated with a specific atomic configuration. Each of these subfolders contains files with .cfg format, corresponding to outputs for each atomic configuration The total number of atomic configurations contained in atoms256.zip is 65,046. The total number of atomic configurations contained in atoms864.zip is 63,936. The total number of atomic configurations contained in atoms2048.zip is 61,997. The total number of atomic configurations spanned by the entire dataset is 190,979. References [1] https://www.lammps.org/ [2] https://openkim.org/ [3] https://openkim.org/id/MEAM_LAMMPS_KimSeolJi_2017_PtNi__MO_020840179467_001 [4] El-Gendy, Ahmed A. and Hampel, Silke and Büccchner, Bernd and Klingeler, Rüdiger, Tuneable magnetic properties of carbon-shielded NiPt-nanoalloys, RSC Adv., volume 6, issue 57, pages 52427-52433, 2016, The Royal Society of Chemistry, doi:10.1039/C6RA05910D

36 MATERIALS SCIENCE↗
DOE OSTI2021

Final Reports of the 2021 Los Alamos National Laboratory Computational Physics Student Summer Workshop

Since 2011, the Los Alamos National Laboratory Computational Physics Student Summer Workshop has been bringing together a highly talented and diverse group of students every summer. Students work in teams of two, alongside typically two mentors, on research projects reflecting a broad range of topics within computational physics. In addition, students attend a series of lectures on topics within computational physics, facility tours, and networking events. The program lasts ten weeks, with this year’s workshop running from June 7 to August 13. At the end of the summer, students give a final presentation, along with a written report. Those reports are what make up the remaining sections of this document. Admission to the workshop is by a competitive process, with the mentors forming the selection committee. One of the important accomplishments of the workshop has been to create a student pipeline from diverse schools that sometimes are not normally tapped by LANL recruiting. Many workshop students maintain a continuing relationship with LANL, returning as student interns, post-doctoral researchers, and staff members. Additionally, workshop alumni act as ambassadors for LANL. The result is a wider awareness both of LANL as a potential employer, and of the technical work that happens at LANL. This year, the workshop was once again in an off-site, virtual format. Students worked on LANL virtual desktop systems remotely, also accessing LANL HPC resources. In order to facilitate communication, student were given accounts on both Webex, a video teleconferencing platform, and Mattermost, an online team collaboration and chat platform, similar to Slack. Daily communication between students and mentors was primarily on Mattermost, with Webex conferencing as needed. The lectures were all done on Webex. Given the difficulty of the virtual format, and a concern that students might have video teleconferencing burn-out, all lectures were optional this year. In spite of this, the attendance was generally high. Lecturers were asked to try to move to a more high-level, ”What is it?,” format. Once again, the students did a tremendous job. Over the course of ten weeks, they did important research across a staggering array of disciplines. The following pages contain the final report for each team’s research efforts. Enjoy!

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2024

Project DarkStar: Vision for LLNL in 2030

DarkStar was a Strategic Initiative (FY2021-FY2024) to investigate applications of Artificial Intelligence (AI) and Machine Learning (ML) to scientific problems of complex hydrodynamics, shockwave physics and energetic materials. The research focused on physics and engineering design as a process that can be tremendously accelerated through merging AI with advanced physics simulation on exascale-class platforms, and to experimentally validate this revolutionary new approach through dynamic materials campaigns. A central thread of scientific inquiry was in the application of AI to enable human understanding of how to control hydrodynamic instability (which has impacts to areas such as inertial confinement fusion) via engineering features and time-dependent sources. Motivated by an unfinished line of research started by Dr. Johnny von Neumann, AI-enabled simulation approaches were developed that allowed DarkStar researchers to uncover several ground-breaking discoveries regarding hydrodynamic instability, including how to completely suppress Richtmyer-Meshkov instability (RMI). These S&T discoveries, along with other advances, have shown the way for an entirely new approach to time-dependent problems known as inverse design – the idea that complex systems can be developed directly from a final state that is to be achieved and resolve the initial design via satisfying several constraints simultaneously via AI/ML. Through experimental campaigns conducted across a wide range of facilities in the NNSA complex (the High Explosive Application Facility at LLNL, the Dynamic Compression Sector/Advanced Photon Source at Argonne National Lab, and Special Technologies Laboratory at MSTS) the radical new AI/ML approach to engineering complex material dynamics was verified, establishing a new field of study within the realm of shock physics. As advanced manufacturing capabilities continue to develop, the great importance of inverse design as a means to apply that technology effectively for NNSA missions will feature prominently over this decade. DarkStar has positioned NNSA as a world-leader in this newly emerging cross-disciplinary area of AI methods for advanced physics simulation and pioneered multiple novel approaches that have enabled the broader scientific community. By allowing us to see past the horizon, to 2030 and beyond, DarkStar has illuminated the vast potential of AI/ML to impact a wide range of new national security missions and, consequently, multiple areas of further research have already emerged across the NNSA and DOD complex.

42 ENGINEERING↗
DOE OSTI2020

NWChem: Past, present, and future

Specialized computational chemistry packages have permanently reshaped the landscape of chemical sciences by providing tools to support and guide the experimental effort and for prediction of chemical and materials properties. In this regard, a special role has been played by electronic structure packages where complex chemical and materials processes can be modeled using first-principle-driven methodologies. Over the last few decades, the rapid development of computing technologies and a tremendous increase in computational power has offered a unique chance to study complex chemical transformations using sophisticated and predictive many-body techniques to describe correlated behavior of electrons in molecular and condensed phase systems at different levels of theory. In enabling these simulations, a critical role has been played by novel parallel algorithms capable of taking advantage of computational resources to address polynomial scaling of electronic structure methods. NWChem was among the first electronic structure codes that focused on delivering scalable performance for electronic structure simulations. Herein, we briefly review the NWChem suite of computational codes including its history, design principles, parallel tools, current capabilities, outreach and outlook.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Importance of Electron Correlation on the Geometry and Electronic Structure of [2Fe–2S] Systems: A Benchmark Study of the [Fe 2 S 2 (SCH 3 ) 4 ] 2–,3–,4– , [Fe 2 S 2 (SCys) 4 ] 2– , [Fe 2 S 2 (S- p -tol) 4 ] 2– , and [Fe 2 S 2 (S- o -xyl) 4 ] 2– Complexes

Iron–sulfur clusters are crucial for biological electron transport and catalysis. Obtaining accurate geometries, energetics, manifolds of their excited electronic states, and reduction energies is important to understand their role in these processes. Here, using a [2Fe–2S] model complex with Fe II and Fe III oxidation states, which leads to different charges, i.e., [Fe 2 S 2 (SMe) 4 ] 2–,3–,4– , we benchmarked a variety of computational methodologies ranging from density functional theory (DFT) to post-Hartree–Fock methods, including complete active space self-consistent field (CASSCF), multireference configuration interaction, the second-order N-electron valence state perturbation theory (NEVPT2), and the linearized integrand approximation of adiabatic connection (AC0) approaches. Additionally, we studied three experimentally well-characterized complexes, [Fe 2 S 2 (SCys) 4 ] 2– , [Fe 2 S 2 (S-o-tol) 4 ] 2– , and [Fe 2 S 2 (S-o-xyl) 4 ] 2– , via DFT methods. We conclude that the dynamic electron correlation is important for accurately predicting the geometry of these complexes. Broken symmetry (BS) DFT correctly predicts experimental geometries of low-spin multiplicity, while CASSCF does not. However, BS-DFT significantly overestimates the difference between the low- and high-spin electronic states for a given oxidation state. At the same time, CASSCF underestimates it but provides relative energies closer to the reference NEVPT2 results. Finally, AC0 provides energetics of NEVPT2 quality with the additional advantage of being able to use large CASSCF sizes. NEVPT2 gives the best estimates of the Fe III /Fe III → Fe II /Fe III (4.27 eV) and Fe II /F III → Fe II /F II (7.72 eV) reduction energies. The results provide insight into the electronic structure of these complexes and assist in the understanding of their physical properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Final Reports of the 2020 Los Alamos National Laboratory Computational Physics Student Summer Workshop

For the past ten years, the workshop has been bringing a highly talented and diverse group of student every summer. Students work in teams of two, alongside typically two mentors, on research projects reflecting a broad range of topics within computational physics. In addition, students attend a series of lectures on topics within computational physics, facility tours, and networking events. The program lasts ten weeks, with this year’s workshop running from June 8 to August 14. At the end of the summer, students give a final presentation, along with a written report. Those reports are what make up the remaining sections of this document. Admission to the workshop is by a competitive process, with the mentors forming the selection committee. One of the important accomplishments of the workshop has been to create a student pipeline from diverse schools that sometimes are not normally tapped by LANL recruiting. Many workshop students maintain a continuing relationship with LANL, returning as students interns, post-doctoral researchers, and staff members. Additionally, workshop alumni act as ambassadors for LANL. The result is a wider awareness both of LANL as a potential employer, and of the technical work that happens at LANL. This year, the workshop format was changed in several ways, in order to accommodate the off-site, virtual format. Students worked on LANL virtual desktop systems remotely, also accessing LANL HPC resources. In order to facilitate communication, student were given accounts on both Webex, a video teleconferencing platform, and Mattermost, an online team collaboration and chat platform, similar to Slack. Daily communication between students and mentors was primarily on Mattermost, with Webex conferencing as needed. The lectures were all done on Webex. Given the difficulty of the virtual format, and a concern that students might have video teleconferencing burn-out after an academic semester largely moved to that format, all lectures were optional this year. In spite of this, the attendance was generally high. Lecturers were asked to try to move to a more high-level, ”What is it?,” format. Once again, the students did a tremendous job. Over the course of ten weeks, they did important research across a staggering array of disciplines. The following pages contain the final report for each team’s research efforts. We hope you will find reading them as exciting as it was for us to produce them.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Schrödinger cat states of a nuclear spin qudit in silicon

High-dimensional quantum systems are a valuable resource for quantum information processing. They can be used to encode error-correctable logical qubits, which has been demonstrated using continuous-variable states in microwave cavities or the motional modes of trapped ions. For example, high-dimensional systems can be used to realize ‘Schrödinger cat’ states, which are superpositions of widely displaced coherent states that can be used to illustrate quantum effects at large scales. Recent proposals have suggested encoding qubits in high-spin atomic nuclei, which are finite-dimensional systems that can host hardware-efficient versions of continuous-variable codes. Here, in this study, we demonstrate the creation and manipulation of Schrödinger cat states using the spin-7/2 nucleus of an antimony atom embedded in a silicon nanoelectronic device. We use a multi-frequency control scheme to produce spin rotations that preserve the symmetry of the qudit, and we constitute logical Pauli operations for qubits encoded in the Schrödinger cat states. Our work demonstrates the ability to prepare and control non-classical resource states, which is a prerequisite for applications in quantum information processing and quantum error correction, using our scalable, manufacturable semiconductor platform.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Characterizing non-Markovian and coherent errors in quantum simulation

Quantum simulation of many-body systems, particularly using ultracold atoms and trapped ions, presents a unique form of quantum control—it is a direct implementation of a multi-qubit gate generated by the Hamiltonian. As a consequence, it also faces a unique challenge in terms of benchmarking, because the well-established gate benchmarking techniques are unsuitable for this form of quantum control. Here we show that the symmetries of the target many-body Hamiltonian can be used not only to benchmark but to characterize experimental errors in the quantum simulation. We use our results to develop protocols to characterize these errors, which can be implemented using state-of-the-art technology. We consider two forms of errors: (i) unitary errors arising out of systematic errors in the applied Hamiltonian and (ii) canonical non-Markovian errors arising out of random shot-to-shot fluctuations in the applied Hamiltonian. We show that the dynamics of the expectation value of the target Hamiltonian itself, which is ideally constant in time, can be used to characterize these errors. In the presence of errors, the expectation value of the target Hamiltonian shows a characteristic thermalization dynamics, when it satisfies the operator thermalization hypothesis (OTH). That is, an oscillation in the short time followed by relaxation to a steady-state value in the long time limit. We show that while the steady-state value can be used to characterize the coherent errors, the amplitude of the oscillations can be used to estimate the non-Markovian errors. We prove a sandwich theorem to establish a linear relation between the amplitude of the oscillations and the magnitude of the non-Markovian errors. Moreover, by varying the initial state, we show that the steady state values can be used to completely construct the generator of the coherent errors. Using these results, we develop two experimental protocols to characterize the unitary errors based on these results, one of which requires single-qubit addressing and the other one doesn't. We also develop a protocol to characterize non-Markovian errors. Published by the American Physical Society 2024

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Progress report on analytic and numerical studies of x-ray-induced impulse

In a variety of high-energy-density (HED) systems, x-rays of a given energy are used to generate shockwaves, bulk motion, and impulse in materials. As radiation energy is deposited within the material, the material is heated. The number of photons of a certain wavelength absorbed is determined by the spectral intensity of the radiation and the material’s opacity evaluated at that wavelength. This heating results in a pressure increase dictated by the material’s equation of state. Depending on the intensity of the absorbed radiation, it may also cause the material to change phase into a liquid, gas, or plasma. The increased pressure drives the heated surface layer to blow off, imparting impulse and sending a compressive wave into the bulk of the material. Additionally, the compression wave interacts with the solid boundary of the material, resulting in a tensile wave that may cause the material to spall. The impulse generated by the deposition of x-ray energy within the sample can be modeled using purely analytical methods, e.g. the Bethe, Bade, Averell, and Yost (BBAY) model. However, the blow-off process is rather complicated, and proper modeling efforts must account for material ejected by spallation, vaporization, jetting, and plasma ablation. For this reason, analytical models have an unclosed term describing the final energy of the blown-off material Ef(z). Prior modeling efforts have arbitrarily fixed this at some value or modeled it using a limiting set of thermodynamic assumptions. The work we are currently performing uses validated simulations using sophisticated photon transport, equation of state, and strength models/data to provide a fit for Ef(z) that is useful for predictive calculation of impulse. We will apply our methodology and show results for different materials and x-ray sources. This work is particularly useful for the design of experiments studying x-ray impulse generation. The present report is outlined as follows. Section 1.2 describes a series of HED experiments investigating x-ray-generated impulse in materials. Section 1.3 describes the computational approach we employ in this study, and presents validation results against the aforementioned experiments. Section 1.4 introduces analytical models for impulse generation, as well as our method for utilizing impulse from simulations to close the models. We discuss the concept of impulse-spectrum sensitivity, it’s application to uncertainty quantification, and derive a very useful analytical expression for it in 1.5. We then summarize recent progress in this project and discuss future work in section 1.6.

36 MATERIALS SCIENCE↗
DOE OSTI2024

HydraGNN_Predictive_GFM_2024 - Ensemble of predictive graph foundation models for ground state atomistic materials modeling

We provide the ensemble of fifteen pre-trained graph foundation models (GFMs) for atomistic materials modeling applications. Each one of the fifteen GFMs has been trained on five open-source datasets that (once aggregated) amount to over 154 million atomistic structures, which cover over two-thirds of the natural elements of the periodic table and that comprises a broad set of organic and inorganic compounds. This vast set of atomistic structures comprises ground state configurations that are dynamically stable (i.e., equilibrated structures with atomic forces approximately close to zero values) as well as dynamically unstable structures (i.e., non-equilibrium structures with non-negligible non-zero values of atomic forces). The ensemble of datasets aggregated does NOT include excited states. The datasets have been curated to remove atomistic structures with spectral norm of the force tensor above 100 eV/angstrom. Moreover, a linear term of the energy was computed for each dataset using a linear regression model that uses the chemical concentration of each natural element as regressor. The linear term predicted by the linear regression model has been subtracted from each original energy value to perform a re-alignment of the energy values across different electronic structures approximation theories performed to generate the diverse multi-source, multi-fidelity datasets. The folder "ADIOS_files" contains the set of pre-processed datasets in Adaptable I/O System (ADIOS) format (https://www.exascaleproject.org/research-project/adios/) that have been used for the development and training of GFMs in this work. The "ADIOS_files" directory contains 6 sub-directories named as follows: - ANI1x-v3.bp - MPTrj-v3.bp - OC2020-20M-v3.bp - OC2020-v3.bp - OC2022-v3.bp - qm7x-v3.bp Each sub-directory contains the pre-processed datasets converted in Adaptable I/O System (ADIOS) format (https://www.exascaleproject.org/research-project/adios/) that have been used to the development, training, and performance testing of the ensemble go predictive graph foundation models. Each GFM was developed using HydraGNN (https://github.com/ORNL/HydraGNN) as underlying graph neural network (GNN) architecture. The multi-task learning (MTL) capability of HydraGNN was used to simultaneously train the GFMs on labeled values for direct predictions of energy (a total system property of an atomistic structure that measures the chemical stability) and atomic forces (an atomic level property of an atomistic structure that measures the dynamical stability). The hyper parameters of the GFM have been tuned using scalable hyperparameter optimization (HPO) algorithms implemented in the software DeepHyper (https://github.com/deephyper/deephyper). The pre-training of each HPO trial was performed using distributed data parallelism (DDP) to scale the training across 128 compute nodes of the exascale OLCF supercomputer Frontier. Each HPO trial was trained only for 10 epochs and an early stopping was performed to avoid wasting significant computational resources on GNN architectures that were clearly underperforming. For each HPO trial, the 'omnistat' tool developed by (AMD Research - Advanced Micro Device) was used to measure the total energy consumption in kWh. The ensemble of GFMs was obtained by selecting the fifteen best performing HPO trials. Four models have been selected for their clear advantage in accuracy, and these are the GFMs with IDs 229, 156, 147, 260. Additional eleven models have been selected based on judicious balance between accuracy and energy consumption needed for training, and these are the GFMs with IDs 165, 78, 137, 1, 175, 171, 181, 67, 179, 167, 351. Each selected GFM of the ensemble was continued to cumulate a total of at most 30 epochs. In some cases, the total number of epochs actually performed was les than 30 due to two combined factors: (1) the size of the GFM (i.e., the number of model parameters to train) and (2) the total wall-clock time for which the computational resources could be allocated on OLCF-Frontier. The "Ensemble_of_models" directory contains 15 sub-directories named as follows: - gfm_0.229 - gfm_0.156 - gfm_0.147 - gfm_0.260 - gfm_0.165 - gfm_0.78 - gfm_0.137 - gfm_0.1 - gfm_0.175 - gfm_0.171 - gfm_0.181 - gfm_0.67 - gfm_0.179 - gfm_0.167 - gfm_0.351 Each one of these sub-directories refers to one of the fifteen HPO trials that have been selected to continue the pre-training with at most 30 epochs. With each sub-directory associated with a specific HPO trial, the following files can be found: - config.json: file for argument parsing to develop and train an HydraGNN architecture - gfm_0.ID_epoch_N.pk: file with model parameters for HPO ID trial after N epochs of training The ensemble of fifteen GFM architectures was used for (1) ensemble averaging to stabilize the predictions of energy and atomic forces after pre-training for post-processing analysis and (2) ensemble uncertainty quantification (UQ). The code used to develop, pre-train, and load the pre-trained models for post-processing analysis is available on the ORNL-GitHub at the following link: https://github.com/ORNL/HydraGNN/tree/Predictive_GFM_2024

36 MATERIALS SCIENCE↗
DOE OSTI2025

Direct experimental constraints on the spatial extent of a neutrino wavepacket

Despite their high relative abundance in our Universe, neutrinos are the least understood fundamental particles of nature. In fact, the quantum properties of neutrinos emitted in experimentally relevant sources are theoretically contested and the spatial extent of the neutrino wavepacket is only loosely constrained by reactor neutrino oscillation data with a spread of 13 orders of magnitude. Here we present a method to directly access this quantity by precisely measuring the energy width of the recoil daughter nucleus emitted in the radioactive decay of beryllium-7. The final state in the decay process contains a recoiling lithium-7 nucleus, which is entangled with an electron neutrino at creation. The lithium-7 energy spectrum is measured to high precision by directly embedding beryllium-7 radioisotopes into a high-resolution superconducting tunnel junction that is operated as a cryogenic sensor. Under this approach, we set a lower limit on the Heisenberg spatial uncertainty of the recoil daughter of 6.2 pm, which implies that the final-state system is localized at a scale more than a thousand times larger than the nucleus itself. From this measurement, the first, to our knowledge, direct lower limit on the spatial extent of a neutrino wavepacket is extracted. These results may have implications in several areas including the theoretical understanding of neutrino properties, the nature of localization in weak nuclear decays and the interpretation of neutrino physics data.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Single-Step Conversion of Ethanol to n-Butene over Ag-ZrO2/SiO2 Catalysts

Ethanol is a promising platform molecule for production of a variety of fuels and chemicals. Of particular interest is producing middle distillate fuels (i.e., jet and diesel blendstock) from renewable ethanol feedstock. State-of-the-art alcohol-to-jet technology requires multiple process steps based on catalytic dehydration of ethanol to form ethylene, followed by sometimes a multi-step oligomerization, and then hydrotreatment and distillation. Here we report on a new catalytic route in which ethanol is directly converted to n-butene (1- and 2-butene mixtures) over Ag-ZrO2/SBA-16, thus offering the potential for a reduction in the number of required processing steps versus conventional alcohol-to-jet technology. This catalyst system provides the balanced metal and Lewis acid sites required to selectively facilitate a cascading sequence of reactions that includes dehydrogenation, aldol condensation, Meerwein–Ponndorf–Verley reduction, dehydration, and hydrogenation. High conversion and selectivity toward either n-butene or 1,3-butadiene is achieved by tuning the hydrogen feed partial pressure and other process/catalyst parameters. With sufficient hydrogen partial pressure 1,3-butadiene is completely and selectively hydrogenated to form n-butene. The reaction mechanism was elucidated through operando-nuclear magnetic resonance investigations coupled with reactivity measurements. Combined experimental-computational investigation reveals how changes in silver and zirconium composition and the silver oxidation state affects reactivity under controlled hydrogen partial pressures and after prolonged run times. Finally, catalyst effectiveness also was demonstrated when using wet ethanol feed, thus highlighting process flexibility in terms of feedstock purity requirements. This work was financially supported by the U.S. Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy, Bioenergy Technologies Office, and was performed at the Pacific Northwest National Laboratory (PNNL) under Contract No. DE-AC05-76RL01830 and the National Renewable Energy Laboratory under Contract No. DE-AC36- 08GO28308. Part of the work conducted by S. A. Akhade was performed under the auspices of the U.S. DOE at Lawrence Livermore National Laboratory under Contract No. DE-AC52-07NA27344. This work was partly supported through the PNNL-WSU Distinguished Graduate Research Program for ADW. NMR and XPS experiments were performed using EMSL (grid.436923.9), a DOE Office of Science User Facility sponsored by the Office of Biological and Environmental Research

Dagle, Vanessa↗
DOE OSTI2023

Laboratory-Scale Coal-Derived Graphene Process (Final Report)

The Energy & Environmental Research Center (EERC) conducted a laboratory-scale coal-derived graphene (CDG) project focused on developing a technological process for making graphene from four U.S. domestic coal or coal wastes, including lignite from North Dakota, subbituminous coal from Wyoming, bituminous coal from Utah, and anthracite from Pennsylvania. The project was divided into two performance or budget periods (BPs), with BP1 comprising the up-front laboratory experiments to make graphene materials from coal beginning on May 1, 2020, to April 30, 2022. BP2 was conducted from May 1, 2022, to April 30, 2023, and was focused on analyzing the CDG process economic feasibility and the technical gaps for technological scale-up and commercialization. During this project, a few different coal-derived high-value products have been demonstrated, including graphite, graphene oxide (GO), reduced graphene oxide (rGO), and graphene quantum dots (GQDs). A new graphite microstructure was discovered and named “croissant graphite” because of the exterior morphological and textural resemblance to croissant food items sold in commercial groceries stores. The new graphite structure and the associated preparation from coal or coal waste feedstocks has been the subject of a U.S. patent application. The systematic experimental processes involving coal cleaning, upgrading, and conversion to high-value carbon products culminated into a developed upgraded coal-to-products (UCP) technology that is being pursued for potential fast-track commercialization, if funding is available. It is envisioned that commercialization of the UCP technology would increase consumption of U.S. domestic coals or coal wastes to make environmentally sustainable high-value products for the electronics industry, high-energy-storage applications, and clean energy technologies such as electric vehicle (EV) lithium-ion batteries (LIBs), for which graphite has become a critical mineral commodity. Croissant graphite microstructures, when observed by field emission scanning electron microscopy (FESEM), display wavy surface morphology and often grow from a base that is made of graphitized particles with honeycomb-like layers, which are believed to be graphene layers. While more studies are needed to fully ascertain the mechanisms of the croissant graphite microstructure formation, it is postulated that their growth may begin from curling of the graphene sheets into ribbon-like structures, and continuous growth and densification of the ribbon-like structures forms croissant microstructures. Additional studies are ongoing to evaluate the electrochemical performance of croissant graphite for LIB applications and to determine the experimental conditions necessary to tune on/off croissant formation so that it can be either optimized or suppressed depending on performance evaluation results. In addition to the discovery of croissant graphite, the graphitization process from the four coal ranks in general was successful. X-ray diffraction (XRD) analysis showed that the degree of graphitization (DoG) ranged from 12% to 80% in an early sample set, and further optimization on lignite coal produces a DoG of about 92%, which was spectacular to see as lignite is the lowest-rank coal. Thus, it is expected that the graphitization performance for higher-rank coals will be similar or better when optimized as well. The coal-derived graphite was used to make GO and rGO. Analytical characterization, e.g., by methods such as Raman spectroscopy, XRD, Fourier transform infrared (FTIR) spectroscopy and FESEM, showed that the sequence of converting the coal to graphite, exfoliating it to GO, and then chemically reducing the GO to rGO was successful. Although coal naturally contains aromatic compounds and some relatively small-sized condensed aromatic units, it does not contain graphene sheets. In the UCP process, the aromatic domains in the coals, particularly low-rank coals, are concentrated and condensed further into graphene sheets, which are ordered into a 3D stack during graphitization. The synthesized graphite is then unpacked by methods such as exfoliation to various graphene products. GQDs were synthesized from all four coal types, and their optical properties were demonstrated to be tunable by the coal precursor preprocessing treatments. In all four coal types, enhanced optical properties were observed for the produced GDQs with incremental improvements made to the coal precursors. GQDs produced from raw coal samples displayed lower ultraviolet–visible (UV–Vis) spectroscopy absorbance intensity compared to those obtained from cleaned and upgraded coal residues. The photoluminescence (PL) intensities also varied with pretreatment conditions and with the concentration of GQDs in aqueous solutions. GQDs obtained from anthracite show longer emission wavelengths and can be excited by visible light as opposed to GQDs derived from the other coal ranks. UV fluorescence 3D maps and spectra revealed that the emission wavelength at which the GQDs solutions display the highest intensity was slightly redshifted based on the coal precursor pretreatments. In low-rank coal (lignite and subbituminous) samples, two clusters were observed in the maps for GQDs, which may suggest that there are potentially two types of fluorophores in solution or two main size populations. The ability to tune the properties of GQDs based on processing methods can be exploited to make GQDs for various optical display or optoelectronics applications. The results also highlight the importance of removing coal-borne impurities to improve the quality of the coal precursor for preparation of graphene products. Coal and/or coal wastes preprocessing methods were developed and applied to clean and upgrade the coal precursors prior to graphitization and subsequent conversion to graphene products. The preprocessing methods involve high specific-gravity separations, mineral acid cleaning (no hydrofluoric acid), and subsequent upgrading by reducing the coal-borne heteroatom (nitrogen, sulfur, and oxygen) content using proprietary chemical agents. Analytical characterization revealed that the preprocessing steps were successful, with ash reductions that range from 38% to 80% and residual ash content that was below the 5 wt% initial target. Based on proximate and ultimate analysis, the heteroatom reduction reactions produced upgraded coal residues with the oxygen content reduced by 8% to 24%, with additional reductions in the nitrogen and sulfur contents. An initial assessment of the waste streams from the UCP process shows very small to negligible environmental impact due to CO 2 , NO x , and SO x because most process steps are performed under inert atmosphere with argon. Consequently, reactive oxygen environments that tend to create these species are avoided. The inorganic and potentially hazardous species are released into aqueous waste streams that are easy to handle for proper disposal. The liquid waste streams were found to contain low-level concentrations of rare-earth elements (REEs), which could be concentrated and recovered as value-added by-products. Additionally, the volatile and gaseous fractions from carbonization and heat treatment contain useful organic compounds that can also be recovered as potential valuable by-products. Thus, the UCP technology is considered an environmentally sustainable and promising emerging technology for making high-value products from coal and coal wastes, with potential additional value-added by-products. Analysis of potential markets for the coal-derived carbon products shows a strong demand in both niche market sectors and across a wide variety of other industrial sectors. Graphite is currently considered a critical mineral commodity that has a large and growing demand in the LIB industry for EV applications. Based on data from Fortune Business Insights (2022) and Marketwatch (2023) reports, the average global graphite market is projected to reach about 33 billion by 2028, growing at a compound annual growth rate (CAGR) of about 7%, with much of this growth expected to be in the LIB industry. GO and rGO have strong market potentials in various application areas, such as coatings for anticorrosion, anti-icing, and antimicrobial protection, thermal barriers, wear resistance, sensors, additive manufacturing such as 3D inks, and others. GQDs are the emerging key player in the bioimaging, photovoltaics, and light-emitting diodes (LEDs) applications, with the potential to replace traditional semiconductor quantum dots (SQDs), which are based on metallic systems that are more toxic and more expensive. Biomedical applications of GQDs are becoming more attractive because of low to no toxicity and extremely low cost compared to SQDs. The major challenges for scale-up and commercialization of coal-derived carbon products such as graphene vary from the inherent attributes of graphene itself to reluctance to accept graphene in new manufacturing processes because of the uncertainty of the unknown. The 2D nature of graphene materials with a thickness of one atom presents significant challenges to proper handling/processing, and process scale-up becomes difficult because it requires high-end, expensive equipment, even for routine handling and analysis for quality assurance and control. Pristine graphene can also be extremely difficult to work into other matrices, thus hindering downstream processibility, especially at large scale. Currently, the cost of graphene and graphene products is still high and presents an economic risk that tends to slow down investment in scaling up emerging technologies. The lack of a standard for graphene materials for quality assurance and quality control poses a great challenge not only for the markets but also for commercialization efforts. A first-look economic feasibility analysis of the UCP technology provided valuable information that suggests the UCP process would be feasible, especially when it is scaled to a pilot scale and could be more competitive at the full scale. Graphitization was found to be the most energy-consuming and most capital-intensive step in the overall process. In small laboratory- and bench-scale experiments, labor is a significant contributor to the total process costs. Although these energy, capital, and labor constraints contribute to a higher selling price for the product, a preliminary economic model suggests that the process would be feasible at large scale when the process is fully integrated, optimized, and automated.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

COLUMBUS─An Efficient and General Program Package for Ground and Excited State Computations Including Spin–Orbit Couplings and Dynamics

The COLUMBUS program system provides the tools for performing high-level multireference (MR) computations, including the multireference configuration interaction (MRCI) method and its multireference averaged quadratic coupled cluster (MR-AQCC) extension, allowing computations on a wide range of fascinating atomic and molecular systems, including the treatment of open-shells and complicated excited state phenomena. The inclusion of spin−orbit coupling (SOC) directly within the MRCI step enables the description of systems containing heavy elements, such as lanthanides and actinides, whose properties are strongly influenced by SOC. Analytic energy gradients and nonadiabatic couplings at the correlated MRCI level provide the foundation for a variety of dynamics studies, giving insight into ultrafast photochemistry. New and ongoing method developments in COLUMBUS include the computation of spin densities, improved descriptions of ionic states, enhancements to the AQCC method, and the porting of COLUMBUS to graphical processing units (GPUs). New external interfaces enable an enhanced description of electronic resonances and molecules in strong laser fields. This work highlights these new developments while providing a detailed account of the diverse applications of COLUMBUS in recent years.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗