Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “model updating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Design and Performance of the Sorbent-Based Atmosphere Revitalization System for Orion

Validation and simulations of a real-time dynamic cabin model were conducted on the sorbent-based atmosphere revitalization system for Orion. The dynamic cabin model, which updates the concentration of H2O and CO2 every second during the simulation, was able to predict the steady state model values for H2O and CO2 for long periods of steady metabolic production for a 4-person crew. It also showed similar trends for the exercise periods, where there were quick changes in production rates. Once validated, the cabin model was used to determine the effects of feed flow rate, cabin volume and column volume. A higher feed flow rate reduced the cabin concentrations only slightly over the base case, a larger cabin volume was able to reduce the cabin concentrations even further, and the lower column volume led to much higher cabin concentrations. Finally, the cabin model was used to determine the effect of the amount of silica gel in the column. As the amount increased, the cabin concentration of H2O decreased, but the cabin concentration of CO2 increased.

Ritter, James A.↗
NASA NTRS2010

Acoustic-Modal Testing of the Ares I Launch Abort System Attitude Control Motor Valve

The Attitude Control Motor (ACM) is being developed for use in the Launch Abort System (LAS) of NASA's Ares I launch vehicle. The ACM consists of a small solid rocket motor and eight actuated pintle valves that directionally allocate.thrust_- 1t.has-been- predicted-that significant unsteady. pressure.fluctuations.will.exist. inside the-valves during operation. The dominant frequencies of these oscillations correspond to the lowest several acoustic natural frequencies of the individual valves. An acoustic finite element model of the fluid volume inside the valve has been critical to the prediction of these frequencies and their associated mode shapes. This work describes an effort to experimentally validate the acoustic finite model of the valve with an acoustic modal test. The modal test involved instrumenting a flight-like valve with six microphones and then exciting the enclosed air with a loudspeaker. The loudspeaker was configured to deliver broadband noise at relatively high sound pressure levels. The aquired microphone signals were post-processed and compared to results generated from the acoustic finite element model. Initial comparisons between the test data and the model results revealed that additional model refinement was necessary. Specifically, the model was updated to implement a complex impedance boundary condition at the entrance to the valve supply tube. This boundary condition models the frequency-dependent impedance that an acoustic wave will encounter as it reaches the end of the supply tube. Upon invoking this boundary condition, significantly improved agreement between the test data and the model was realized.

Davis, R. Benjamin↗
NASA NTRSDate not supplied

Reduction of Aircraft Noise Uncertainty for a Notional Supersonic Business Jet

NASA supported a study by the International Civil Aviation Organization on the environmental impact of adding supersonic aircraft to the existing global fleet by designing a notional 55-tonne supersonic business jet. The aircraft is referred to as the Supersonic Technology Concept Aeroplane (STCA) and has been used in a multitude of studies over the past few years. One of the many studies on this aircraft was the noise produced by the STCA during landing and take-off (LTO) operations. The LTO noise for the STCA was assessed using contemporary noise prediction tools that have been primarily developed for and utilized by subsonic aircraft, resulting in a high level of uncertainty for the STCA noise predictions. NASA has recently been conducting research and developing tools to reduce the uncertainty for airport noise predictions of supersonic aircraft. The initial focus of the uncertainty reduction was on the jet and inlet-radiated fan noise produced by supersonic engine systems since these sources are dominant during take-off and landing operations for supersonic jets. The results of these efforts are discussed and applied to the STCA model to update the airport noise predictions and associated uncertainty metrics. It is shown that by using new noise source prediction models, the overall system-level cumulative noise uncertainty of the study vehicle is reduced from a standard deviation of 7.8 EPNdB to 2.0 EPNdB.

uncertainty↗
NASA NTRS2015

Formaldehyde Production from Isoprene Oxidation Across NOx Regimes

The chemical link between isoprene and formaldehyde (HCHO) is a strong, non-linear function of NOx (= 27 NO + NO2). This relationship is a linchpin for top-down isoprene emission inventory verification from orbital HCHO column observations. It is also a benchmark for overall mechanism performance with regard to VOC oxidation. Using a comprehensive suite of airborne in situ observations over the Southeast U.S., we quantify HCHO production across the urban-rural spectrum. Analysis of isoprene and its major first-generation oxidation products allows us to define both a "prompt" yield of HCHO (molecules of HCHO produced per molecule of freshly-emitted isoprene) and the background HCHO mixing ratio (from oxidation of longer-lived hydrocarbons). Over the range of observed NOx values (roughly 0.1 - 2 ppbv), the prompt yield increases by a factor of 3 (from 0.3 to 0.9), while background HCHO increases by more than a factor of 2 (from 1.5 to 3.3 ppbv). We apply the same method to evaluate the performance of both a global chemical transport model (AM3) and a measurement-constrained 0-D chemical box model. Both models reproduce the NOx dependence of the prompt HCHO yield, illustrating that models with updated isoprene oxidation mechanisms can adequately capture the link between HCHO and recent isoprene emissions. On the other hand, both models under-estimate background HCHO mixing ratios, suggesting missing HCHO precursors, inadequate representation of later-generation isoprene degradation and/or under-estimated hydroxyl radical concentrations. Moreover, we find that the total organic peroxy radical production rate is essentially independent of NOx, as the increase in oxidizing capacity with NOx is largely balanced by a decrease in VOC reactivity. Thus, the observed NOx dependence of HCHO mainly reflects the changing fate of organic peroxy radicals.

VOC↗
DOE OSTI2026

Resource-Adaptive Federated Text Generation with Differential Privacy

In cross-silo federated learning (FL), sensitive text datasets remain confined to local organizations due to privacy regulations, making repeated training for each downstream task both communication-intensive and privacy-demanding. A promising alternative is to generate differentially private (DP) synthetic datasets that approximate the global distribution and can be reused across tasks. However, pretrained large language models (LLMs) often fail under domain shift, and federated finetuning is hindered by computational heterogeneity: only resource-rich clients can update the model, while weaker clients are excluded, amplifying data skew and the adverse effects of DP noise. We propose a flexible participation framework that adapts to client capacities. Strong clients perform DP federated finetuning, while weak clients contribute through a lightweight DP voting mechanism that refines synthetic text. To ensure the synthetic data mirrors the global dataset, we apply control codes (e.g., labels, topics, metadata) that represent each client’s data proportions and constrain voting to semantically coherent subsets. This two-phase approach requires only a single round of communication for weak clients and integrates contributions from all participants. Experiments show that our framework improves distribution alignment and downstream robustness under DP and heterogeneity.

Wang, Jiayi [ORNL]↗
DOE OSTI2020

Subspace Methods in Multi-Parameter Seismic Full Waveform Inversion

In full waveform inversion (FWI) high-resolution subsurface model parameters are sought. FWI is normally treated as a nonlinear least-squares inverse problem, in which the minimum of the corresponding misfit function is found by updating the model parameters. When multiple elastic or acoustic properties are solved for, simple gradient methods tend to confuse parameter classes. This is referred to as parameter cross-talk; it leads to incorrect model solutions, poor convergence and strong dependence on the scaling of the different parameter types. Determining step lengths in a subspace domain, rather than directly in terms of gradients of different parameters, is a potentially valuable approach to address this problem. The particular subspace used can be defined over a span of different sets of data or different parameter classes, provided it involves a small number of vectors compared to those contained in the whole model space. Additionally, in a subspace method, the basis vectors are defined first, and a local minimum is found in the space spanned by these. We examine the application of the subspace method within acoustic FWI in determining simultaneously updates for velocity and density. We first discuss the choice of basis vectors to construct the spanned space, from linear updates by distinguishing only the contributions of different parameter classes towards nonlinear updates by adding the contributions of higher-order perturbations of each parameter class. The numerical character of FWI solutions generated via subspace methods involving different basis vectors is then analyzed and compared with traditional FWI methods. The subspace methods can provide better reconstructions of the model, especially for the velocity, as well as improved convergence rates, while the computational costs are still comparable with the traditional FWI methods.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Emissions mitigation technology for advanced water-lean solvent-based CO 2 capture processes

This technical final report submitted to DOE/NETL presents all the research activities performed during the entirety of DE-FE0031660 project-Emissions Mitigation Technology for Advanced Water-Lean Solvent-Based CO 2 Capture Processes which spans from October 2018 through March 2022. RTI International has been conducting studies from fundamental and operational aspects to reduce the overall amine emissions from the advanced Water-Lean Solvent (WLS) systems, specifically RTI’s Non-Aqueous Solvent (NAS). This technical final report will highlight the key findings from project which align closely to the project objectives which are: Identify the contribution of vapor loss, entrainment, and aerosols to the overall emissions of water-lean systems; Determine the significance of CO 2 capture system operating parameters to the amine emissions; Develop an emissions model based on critical operating parameters; Evaluate the effectiveness of emissions mitigation devices to reduce the amine emissions to <1 ppm under flue coal-fired flue gas; and, Determine the contribution of the ECTs to the overall CO 2 capture cost. The following are the key findings based on numerous tests using both lab-scale setups and parametric testing performed at RTI’s Bench-scale Gas Absorption System (BsGAS). During the BP1, the aerosol generation system and monitoring equipment were installed at BsGAS to produce and determine the aerosol characteristics during the NAS CO 2 capture process. The aerosol produced by this setup produced aerosols with the peak diameter and concentration of 50 micron and 1.2E10 7 cm -3 , respectively. These particle sizes and concentrations are matched to those observed in the actual coal-fired power plant flue gases and expected to be found at the absorber inlet of the CO 2 capture system. Over 1,300 hours of parametric testing have been conducted to evaluate the impact of the aerosols and operating conditions during the CO 2 capture with NAS on the overall amine emissions in the treated flue gas. At the worse condition tested, the presence of the aerosols in the flue gas could increase the overall emissions by 10X compared to the baseline emissions from NAS’s vapor pressure. CO 2 capture rate was found to be a main factor impacting the overall emissions as well as aerosol size and concentrations in the absorber off-gas. The higher CO 2 capture rate, the higher amine emissions in the treated gas. The temperature difference between the temperature bulge seen in the absorber and the water wash temperature also impacts the particle growth where the larger the temperature difference, the more amine emissions from aerosols in the treated gas. The majority of the aerosols did not grow substantially in the system, and the particle concentrations remained nearly constant between the absorber inlet and wash outlet. Only a small portion of the particles were found to grow significantly. The high efficiency demister with mesh size of 5-10 micron can be installed to remove a portion of the aerosols from the gas stream leaving the water wash. Overall, these results from parametric testing have established the emission baseline and validate our assumption on the need of emission control technologies (ECT) in order to minimize the emissions from the baseline NAS CO 2 capture process. Over 2,000 of BsGAS operating hours was used to investigate a handful of process improvements which led to a selection of the vital few changes that effectively control the amine emissions. These process improvements are lime-coated-filters for absorber gas inlet, advanced demister at the top of the absorber, a second water wash with amine recovery unit were designed, installed, and tested at BsGAS at the end of BP1. The result showed that the NAS CO 2 capture process with these additional emission control devices could lower the amine emission in the treated gas to about 1 ppm using a simulated coal-fire flue gas stream. The main contributor in lowering the amine emission came from the second water wash with amine recovery unit where the amine concentration in the scrubbing water was kept below 2 wt% through a continuous amine removal via an adsorbent bed, resulting in a low amine vapor pressure. The adsorbent bed was regenerated via a direct steam regeneration and the recover amine was returned to the absorber to minimize wastewater and makeup amine. A flue gas generation system was designed and installed during the first half of BP2 to support the emission testing using a real coal-derived flue gas. The system is capable of generating both coal- and natural gas- derived flue gases with the composition of the gaseous species highly resemble to that of the power plant flue gases. The particulates detected in the coal-derived flue gas showed the mean diameter of 1 micron. The CO 2 capture operating was then proceed using the real coal-derived flue gas where the amine emission was controlled to be about 0-3 ppm for the total run time of about 200 hours. Similar testing was conducted with natural gas-derived flue gas and the result showed a highly amine emission of 30 ppm under the total run time of 200 hours. The Principal Component Analysis (PCA) and the Partial Least Squares Projection to Latent Structures (PLS) techniques were applied to the parametric testing data to derive a multivariate statistical model. The model was validated and trained with half of the data collected, and the predictive ability of the model was evaluated using the remaining half of the data. The resulting empirical model was capable of predicting the overall emissions from the NAS process without the ECTs with ±15% accuracy (average absolute deviation, AAD) in BP1. As more emission data were obtained under the real coal-flue gas in the BP2, the model incorporated these new set of data to reflect the final process configuration, operating parameters, and amine emission. This results in the updated empirical model predicting the amine emission from the NAS CO 2 capture process with 84% goodness-of-fit (R 2 ), 85% predictability (Q 2 ), and 15% AAD. The study evaluates the use of RTI’s Non-Aqueous Solvent technology for 90% CO 2 capture from a net 650 MWe pulverized coal power plant, downstream of the flue-gas desulfurization unit. The captured CO 2 has a purity of > 95% CO 2 , and is dried, compressed to 15.3 MPa (2,215 psia), ready for sequestration. The analysis uses Case B12B from the DOE Baseline study on Bituminous Coal, Revision 4 where the Cansolv CO 2 capture plant is replaced by the RTI CO 2 Capture plant. The CO 2 capture plant has been sized to capture >90% CO 2 from flue gas derived from a net 650 MWe supercritical pulverized coal power plant. The CO 2 capture plant is equipped with emission control technologies that limits the amine emissions to < 1 ppm. Two different cases were evaluated for the technoeconomic study. The key difference between the two cases is the regenerator pressure. In Case 1, the regenerator operates at 0.195 MPa (28.3 psia), whereas in Case 2, the regenerator pressure is 0.44 MPa (64 psia) thus removing the need for the first stage of compression of the eight-stage compression train. Results from the TEA are compared against the DOE reference cases for SCPC plant with and without CO 2 Capture (Case B12A and Case B12B of the DOE Baseline study, respectively). Case 2 with CO 2 regeneration at higher pressure results in the lower cost of CO 2 capture. The total capital cost of the capture process has been estimated using 2018 dollars in Aspen Process Economic Analyzer and was estimated to be $579 MM. The capture plant operation leads to a total parasitic power loss rate of 96 MWe, resulting in a decrease in pulverized coal power plant efficiency of 7.8% points. The resulting cost of electric power increases from 64.4 mills/kWh, for no capture, to 97.5 mills/kWh, with 90% capture, an increase of 51% in the COE. The cost of capturing 90% CO 2 was estimated to be $38.2/tonne-CO 2 , and meets the DOE target of $40/t-CO 2 . Emission control technologies (ECT) investigated in this project includes a second water wash with use of activated carbon beds for removal of amine from the wash water prior to recirculation in the water wash. These ECT allow operation of the CO 2 capture plant with < 1 ppm amine emissions with the treated flue gas and contributes to $2.4/t-CO 2 captured. Amine emissions derived from thermal and oxidative degradations were investigated under this project along with the emissions derived from aerosols for the NAS system. The thermally degraded of the lean NAS showed less than 4% decreased of the original total amine content in the NAS at 150 °C while the result obtained at 120 °C showed no drop in total amine content, suggesting that thermal degradation of the NAS is minimal. These results also suggested that the thermally degraded species are not likely formed and contributed to the emissions due to the low regeneration temperature of the NAS at 90-105 °C. The oxidative degradation, on the other hand, could become problematic as some of these oxidative degraded species were observed during the NAS-5 testing at National Carbon Capture Center (NCCC) and SINTEF in our previous project. The rapid screening of selected inhibitors suggested that oxidative degradation of NAS can be suppressed using thiol containing compounds in amounts of at least 1 mol%. The detailed mechanistic degradation pathway was conceived for a specific amine used in NAS formulation during BP2. he reduction of the nitrosamines caused by the NO x present in the flue gas was also examined. The study suggested that the thermo-chemical treatment of the NAS solvent would be a more effective and economically viable compared to removing NO x at the DCC.

01 COAL, LIGNITE, AND PEAT↗
NASA NTRS2005

CoMET: Cost and Mass Evaluation Tool for Spacecraft and Mission Design

New technology in space exploration is often developed without a complete knowledge of its impact. While the immediate benefits of a new technology are obvious, it is harder to understand its indirect consequences, which ripple through the entire system. COMET is a technology evaluation tool designed to illuminate how specific technology choices affect a mission at each system level. COMET uses simplified models for mass, power, and cost to analyze performance parameters of technologies of interest. The sensitivity analysis that CoMET provides shows whether developing a certain technology will greatly benefit the project or not. CoMET is an ongoing project approaching a web-based implementation phase. This year, development focused on the models for planetary daughter craft, such as atmospheric probes, blimps and balloons, and landers. These models are developed through research into historical data, well established rules of thumb, and engineering judgment of experts at JPL. The model is validated by corroboration with JpL advanced mission studies. Other enhancements to COMET include adding launch vehicle analysis and integrating an updated cost model. When completed, COMET will allow technological development to be focused on areas that will most drastically improve spacecraft performance.

Bieber, Ben S.↗
DOE OSTI2023

Composite Analysis for Low-Level Waste Disposal in the Hanford Site Central Plateau (FY 2020) (Rev. 2)

This document provides an updated Hanford Site composite analysis (CA). A Hanford Site CA was prepared and issued in 1998 (PNNL-11800) with an addendum provided in 2002 (PNNL-11800 Addendum 1). The CA was approved in 2002 (Frei, 2002) and has been maintained (DOE/RL-2000-29 and subsequent revisions) to support low-level waste disposal performance assessments (PAs) and disposal authorizations for facilities at the Hanford Site, including the following: Continued operation of the Environmental Restoration Disposal Facility (ERDF) and the 200 East and 200 West Low-Level Burial Grounds; Construction of the Integrated Disposal Facility (IDF); Forthcoming closure of tank residual waste systems such as Waste Management Area (WMA) C. The CA maintenance program resulted in a determination in 2015 (DOE/RL-2015-66) that the Hanford Site CA needed an update for the following reasons: While the initial Hanford Site CA has been maintained since 2001, the accumulation of basis changes reported in the annual summary reports over the succeeding 14 years merit evaluation in an updated analysis; The U.S. Department of Energy (DOE) Headquarters requested in a memorandum in 2015 (Gilbertson and Marcinowski, 2015) that “as soon as the relevant PAs are complete, the CA will be revised to account for all of the new information.” This updated Hanford Site CA accounts for the following new information: 1. Inclusion of a detailed Hanford Site baseline disposition that projects remedial activities through site closure. There have been significant changes through decision making in the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) process that were not available when the original CA was produced; 2. Inclusion of an updated inventory basis, new modeling capabilities, and new decisions reached in the associated record of decision (ROD) that was provided by issuance of DOE/EIS-0391 in fiscal year (FY) 2013. Development of a Hanford Site groundwater model from the baseline provided in a technical transfer of models for the Final Tank Closure and Waste Management Environmental Impact Statement (DOE/EIS-0391) commenced in FY 2014 and resulted in the plateau-to-river (P2R) groundwater flow model that is used in this updated Hanford Site CA; 3. Accounting for pump and treat systems, which were not evaluated in the initial CA. Pump and treat systems have had significant impact on groundwater flow system behavior, contaminant transport, and contaminant removal from Hanford Site groundwater. This process is accounted for in the use of the P2R model for this updated Hanford Site CA; 4. Inclusion of water-level data collected since the initial CA was completed. Data collected as the unconfined aquifer water levels continue to recede since the cessation of large liquid discharges in the late 1990s have led to marked improvement in understanding of the flow system for future conditions, particularly regarding northward flow potential in the critical Gable Gap area. The calibration in the latest version of the P2R model accounts for this information; 5. Inclusion of results from the revised ERDF PA completed in 2013 (WCH-5209) that account for updated inventory and expansion of the ERDF facility to about twice the size that was evaluated in the original CA; 6. Use of updated geoframeworks to provide the structural basis for numerical fate and transport models in the groundwater pathway of this updated CA. The geologic basis for groundwater models has continued to improve with additional data collection and interpretation with the creation and maintenance of the Hanford South Geoframework and the Central Plateau Vadose Zone Geoframework tools; 7. Incorporation of updated tank residual inventory estimates. Tank residual inventory estimates have improved with the incorporation of tank retrieval inventory data for those tanks that have completed retrieval. The CA inventory data package includes this updated information; 8. Incorporation of WMA C PA results. Two additional PAs for tank farm closure decisions are in preparation during the period required to prepare an updated Hanford Site CA: WMA C (FY 2016) and WMA A-AX (in preparation). The WMA C PA results are incorporated into the updated Hanford Site CA, and its grouted residuals model is used as the basis for a release model to account for the other tank farm systems modeling in this updated CA; 9. An update to the IDF PA was submitted in FY 2017 and has been reviewed and approved. The results of the IDF PA are incorporated into this updated CA; 10. Updated risk assessment scenarios. The risk assessment scenarios currently in use for Hanford Site CERCLA and Resource Conservation and Recovery Act of 1976 (RCRA) analyses differ from those evaluated in the initial Hanford Site CA. The representative person exposure scenario evaluated in this updated Hanford Site CA is consistent with recent PAs and CERCLA and RCRA analyses as the Hanford Site. This updated Hanford Site CA provides the following: A comparison of the updated Hanford Site CA all-pathway dose results with the performance measures during the compliance period, which is assumed to begin with site closure in calendar 2070 with the last scheduled disposal action and continue for 1,000 years postclosure (to calendar year 3069); A comparison of Hanford Site CA all-pathway dose results with the performance measures during the postcompliance period to address potential peaks beyond the compliance period. This is accomplished by evaluating dose in the period for 9,000 years following the compliance period (i.e., from calendar year 3070 to 12070).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS2007

CREME96 Update/Replacement Efforts

This talk concerns the plans to update the CREME96 model that is currently available on the WWW. The talk states the reasons for updating C REME. It describes the updates that are planned, including the single event prediction paradigm, the method of radiation transport through the spacecraft to the electronic component of interest and the planned updates to models for the space radiation environment. It also revi ews user suggestions received do date for the update.

Adams, Jim H.↗
DOE OSTI2025

Experimental and fuel-surrogates modeling study of the high-pressure pyrolysis of specialty cetane number fuels: implications for fall-off in ethylene unimolecular dissociation

Single pulse shock tube experiments were conducted at 50 atm nominal pressure and 4 ms nominal reaction time over a temperature range of 900–1800 K, to study the pyrolysis speciation of a multi-component jet fuel, F-24, and six cetane number (CN) specialty fuels - CN30, CN35, CN40, CN45, CN50, and CN55. Gas chromatography (GC) was used to qualitatively and quantitatively analyze the post shock gases. The relationship between the formation of key pyrolysis species and the chemically controlled combustion propensity as reflected by the cetane number of each fuel was examined. A surrogate-based mechanism from the CRECK Modelling Group and chemical-functional group based optimized surrogates (CFGO) were used to simulate the pyrolysis speciation results. The model was able to capture the chemistry of most species except two important pyrolysis intermediates – ethylene and acetylene. Chemical kinetic analyses were performed to identify the important reactions which affect the chemistry of these species; however, the rate parameters of critical reactions were found to be unsuitable for simulating the present high-pressure studies. Here, to address this unsuitability, a theory-based fall-off analysis for three reactions representing the decomposition of ethylene and subsequent formation of acetylene was performed, and these are included in an updated version of the CRECK mechanism. This update resolves discrepancies between the experimental results and simulations for ethylene and acetylene. Reaction flux analyses using the updated surrogate model were also performed to identify the important reaction pathways responsible for the formation of crucial species and to provide an analysis of the chemistry of complex multi-component fuel systems. The fundamental reactions responsible for driving pyrolysis chemistry were greatly influenced by the chemical functional groups present in these fuels. In addition to updating the rate parameters of specific reactions to improve modeling, this study also emphasizes the effectiveness of the fuel-surrogate approach, where surrogates representing the chemical functional group composition of the parent fuel serve as a valuable tool for predicting the combustion chemistry of novel fuels.

Chemical Kinetics↗
DOE OSTI2023

Achieving Realistic Runoff in the Western United States with a Land Surface Model Forced by Dynamically Downscaled Meteorology

Abstract In this study, we calibrate a regional climate model’s (RCM) underlying land surface model (LSM). In addition to providing a realistic representation of runoff across the hydroclimatically diverse western United States, this is done to take advantage of the RCM’s ability to physically resolve meteorological forcing data in ungauged regions, and to prepare the calibrated hydrologic model for tight coupling, or the ability to represent land surface–atmosphere interactions, with the RCM. Specifically, we use a 9-km resolution meteorological forcing dataset across the western United States, from the fifth generation ECMWF Reanalysis (ERA5) downscaled by the Weather Research Forecasting (WRF) regional climate model, as an offline forcing for Noah-Multiparameterization (Noah-MP). We detail the steps involved in producing an LSM capable of accurately representing runoff, including physical parameterization selection, parameter calibration, and regionalization to ungauged basins. Based on our model evaluation from 1954 to 2021 for 586 basins with daily natural streamflow, the streamflow bias is reduced from 24.2% to 4.4%, and the median daily Nash–Sutcliffe efficiency (NSE) is improved from 0.12 to 0.36. When validating against basins with monthly natural streamflow data, we obtain a similar reduction in bias and a median monthly NSE improvement from 0.18 to 0.56. In this study, we also discover the optimal setup when using a donor-basin method to regionalize parameters to ungauged basins, which can vary by 0.06 NSE for unique designs of this regionalization method. Significance Statement This study provides useful guidance for improving a land surface model to accurately represent runoff across a spatially extensive and hydroclimatically diverse region (the western United States). The land surface model is updated to represent runoff more accurately at gauged basins, and then additionally updated for basins without observational data using a mathematical approach called the donor-basin method. We make use of a regional climate model’s reanalysis-derived meteorological data and its underlying land surface model to achieve realistic runoff. The calibrated land surface model can thus be tightly coupled in subsequent studies in a manner that should more accurately reflect runoff conditions. Findings from this study will serve as a useful reference for the atmospheric (and hydrologic) modeling communities and their ability to represent large-scale hydrology accurately.

Meteorology & Atmospheric Sciences↗
DOE OSTI2022

Fiberboard Properties and Degradation Rates for Storage of 9975 Shipping Package in KAC (2022 Status Report)

Thermal, mechanical, and physical properties have been measured on fiberboard samples following accelerated aging for up to 17 years. The aging environments include elevated temperature up to 250 °F (the maximum allowed service temperature for fiberboard in 9975 packages) and elevated humidity. Accelerated aging results have been analyzed and used to build aging models. Correlations relating several properties (thermal conductivity, energy absorption, weight, dimensions, and density) to their rate of change in potential storage environments have been developed. Combined with an estimate of the actual conditions the fiberboard experiences in K-Area Complex (KAC), these models allow development of service life predictions. KAC completed calculations that supported extending the service life of 9975 packages with 3013 containers in storage from 20 years to 40 years. These calculations addressed the potential for degraded fiberboard properties following 40 years in storage using degradation models developed previously. Due to differences in containers, 9975 packages with non-3013 containers are only approved for 20 years of storage. The updated degradation models developed in this report have been compared to the assumptions in those calculations, and the current results for fiberboard dimensions, density, radial thermal conductivity, and energy absorption remain consistent with those calculations. The axial thermal conductivity degradation rate slightly exceeds calculations estimate of 0.5% per year between 130 and 160 °F. Additional data will continue to be collected to permit future refinements to the models and assumptions. Some of the predicted degradation rates presented in this report are extreme. However, these relate to environments that do not exist within KAC or would be postulated only as upset conditions that would not likely persist for an extended period. For a typical package stored in KAC with approximately 10-12 watts internal heat load or less, and ambient temperatures below 90 °F, the fiberboard assemblies experience storage conditions less severe than any of the aging environments. Fiberboard in conforming packages with lower internal heat loads should experience little or no degradation and is expected to provide a service life beyond the currently approved 40 year storage period. Packages with higher internal heat loads may not continue to perform their required safety functions beyond 40 years. Ultimately, service life will be determined by the cumulative effect of degradation from all the conditions these packages might encounter. The results and model predictions presented in this report are applicable to 9975 packages with cane or softwood fiberboard overpack assemblies. These degradation models do not address the effects of non-conforming conditions such as the presence of excess moisture and mold or beetle infestations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Core Model Proposal #386: 2023 Hydrogen Update

This proposal includes several updates to the hydrogen system and transportation technologies that were performed between June 2022 and June 2023: hydrogen combustion turbines for backup electricity; updated medium and heavy-duty truck costs; charging infrastructure costs for BEV LDVs; nuclear-hydrogen production update; revision to industrial energy use's hydrogen cogeneration technology; hydrogen emissions and fugitive emissions. It is a follow-up to Core Model Proposal 359.

08 HYDROGEN↗
NASA NTRS1995

An extended plasma model for Saturn

The Saturn magnetosphere model of Richardson and Sittler (1990) is extended to include the outer magnetosphere. The inner magnetospheric portion of this model is updated based on a recent reanalysis of the plasma data near the Voyager 2 ring plane crossing. The result is an axially symmetric model of the plasma parameters which is designed to provide accurate input for models needing either in situ or line-of-sight data and to be a useful tool for Cassini planning.

Richardson, John D.↗
NASA NTRS1986

Space infrared telescope pointing control system. Infrared telescope tracking in the presence of target motion

The use of charge-coupled-devices, or CCD's, has been documented by a number of sources as an effective means of providing a measurement of spacecraft attitude with respect to the stars. A method exists of defocussing and interpolation of the resulting shape of a star image over a small subsection of a large CCD array. This yields an increase in the accuracy of the device by better than an order of magnitude over the case when the star image is focussed upon a single CCD pixel. This research examines the effect that image motion has upon the overall precision of this star sensor when applied to an orbiting infrared observatory. While CCD's collect energy within the visible spectrum of light, the targets of scientific interest may well have no appreciable visible emissions. Image motion has the effect of smearing the image of the star in the direction of motion during a particular sampling interval. The presence of image motion is incorporated into a Kalman filter for the system, and it is shown that the addition of a gyro command term is adequate to compensate for the effect of image motion in the measurement. The updated gyro model is included in this analysis, but has natural frequencies faster than the projected star tracker sample rate for dim stars. The system state equations are reduced by modelling gyro drift as a white noise process. There exists a tradeoff in selected star tracker sample time between the CCD, which has improved noise characteristics as sample time increases, and the gyro, which will potentially drift further between long attitude updates. A sample time which minimizes pointing estimation error exists for the random drift gyro model as well as for a random walk gyro model.

Powell, J. D.↗
DOE OSTI2021

Impact of Urban Pollution on Organic-Mediated New-Particle Formation and Particle Number Concentration in the Amazon Rainforest

A major challenge in assessing the impact of aerosols on climate change is to understand how human activities change aerosol loading and properties relative to the pristine-preindustrial baseline. Here we combine chemical transport simulation and field measurements to investigate the effect of anthropogenic pollution from an isolated metropolis on particle number concentration over the preindustrial-like Amazon rainforest through various new-particle formation (NPF) mechanisms and primary particle emissions. To represent organic-mediated NPF, we employ a state-of-the-art model that systematically simulates the formation chemistry and thermodynamics of extremely low volatility organic compounds as well as their roles in NPF processes, and further update the model to improve organic NPF simulations under human-influenced conditions. Results show that urban pollution from the metropolis increases particle number concentration by a factor of 5–25 over the downwind region (within 200 km from city center) compared to background conditions. Overall, our model indicates that NPF contributes over 70% of the total particle number in the downwind region except immediately adjacent to the sources. Among different NPF mechanisms, the ternary NPF involving organics and sulfuric acid overwhelmingly dominates. The improved understanding of particle formation mechanisms will help better quantify anthropogenic aerosol forcing from pristine-preindustrial times to present day.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

A general framework for removing point-spread function additive systematics in cosmological weak lensing analysis

ABSTRACT Cosmological weak lensing measurements rely on a precise measurement of the shear two-point correlation function (2PCF) along with a deep understanding of systematics that affect it. In this work, we demonstrate a general framework for detecting and modelling the impact of PSF systematics on the cosmic shear 2PCF and mitigating its impact on cosmological analysis. Our framework can detect PSF leakage and modelling error from all spin-2 quantities contributed by the PSF second and higher moments, rather than just the second moments, using the cross-correlations between galaxy shapes and PSF moments. We interpret null tests using the HSC Year 3 (Y3) catalogs with this formalism and find that leakage from the spin-2 combination of PSF fourth moments is the leading contributor to additive shear systematics, with total contamination that is an order-of-magnitude higher than that contributed by PSF second moments alone. We conducted a mock cosmic shear analysis for HSC Y3 and find that, if uncorrected, PSF systematics can bias the cosmological parameters Ωm and S8 by ∼0.3σ. The traditional second moment-based model can only correct for a 0.1σ bias, leaving the contamination largely uncorrected. We conclude it is necessary to model both PSF second and fourth moment contaminations for HSC Y3 cosmic shear analysis. We also reanalyse the HSC Y1 cosmic shear analysis with our updated systematics model and identify a 0.07σ bias on Ωm when using the more restricted second moment model from the original analysis. We demonstrate how to self-consistently use the method in both real space and Fourier space, assess shear systematics in tomographic bins, and test for PSF model overfitting.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗