Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “model scaling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Investigation of ground effects on large and small scale models of a three fan V/STOL aircraft configuration

Induced lift of a subsonic, three fan, lift/cruise, V/STOL aircraft configuration was investigated using scale modes of a multimission aircraft whose design incorporates a nose mounted lift fan and two lift/cruise units located over the wing. Configuration effects were assessed for lift improvement devices, lift/cruise nozzle rails, nozzle perimeter plates, and alternate nose fan exit hubs. Tests were conducted at four model heights (H/D = 0.95, 1.53, 3.06 and 6.45, where D is the average nozzle exit diameter equal to 0.997 m.) Results are presented and discussed.

Schuster, E. P.↗
NASA NTRS1993

Mobility analysis, simulation, and scale model testing for the design of wheeled planetary rovers

The use of computer based techniques to model and simulate wheeled rovers on rough natural terrains is considered. Physical models of a prototype vehicle can be used to test the correlation of the simulations in scaled testing. The computer approaches include a quasi-static planar or two dimensional analysis and design tool based on the traction necessary for the vehicle to have imminent mobility. The computer program modeled a six by six wheel drive vehicle of original kinematic configuration, called the Rocker Bogie. The Rocker Bogie was optimized using the quasi-static software with respect to its articulation parameters prior to fabrication of a prototype. In another approach used, the dynamics of the Rocker Bogie vehicle in 3-D space was modeled on an engineering workstation using commercial software. The model included the complex and nonlinear interaction of the tire and terrain. The results of the investigation yielded numerical and graphical results of the rover traversing rough terrain on the earth, moon, and Mars. In addition, animations of the rover excursions were also generated. A prototype vehicle was then used in a series of testbed and field experiments. Correspondence was then established between the computer models and the physical model. The results indicated the utility of the quasi-static tool for configurational design, as well as the predictive ability of the 3-D simulation to model the dynamic behavior of the vehicle over short traverses.

Lindemann, Randel A.↗
NASA NTRS1974

Results of low speed wind tunnel tests on a .0405 scale model Rockwell Space Shuttle Orbiter tested both in free air and in the presence of a ground plane (OA16)

Experimental aerodynamic investigations were conducted on a .0405 scale representation of the space shuttle orbiter in a 7.75 x 11 foot low speed wind tunnel during the time period March 21, to April 17, 1973. The primary test objectives were to investigate both the aerodynamic and propulsion effects of various air breathing engine systems in free air and in the presence of the ground. The free air portion of this test investigated the aerodynamic effects of engine nacelle number, nacelle grouping, and nacelle location. For this testing the model was sting mounted on a six component internal strain gage balance entering through the model base. The ground plane portion of the aerodynamic test investigated the same nacelle effects at ground plane locations of full scale W.P. = 239.9, 209.3, 158.9, 108.5, and 7.78 in. At the conclusion of the aerodynamic test period the propulsion effects of various nacelle locations and freestream orientations in the presence of the ground were investigated.

Mennell, R. C.↗
NASA NTRS1987

Comparing Test Data on Scale-Model Helicopter Rotors

Hovering data correlate well, but forward-flight data do not. Report compares acoustics and performance of small-scale helicopter rotor with those of full-scale rotor in both hovering and forward flight.

Kitaplioglu, Cahit↗
NASA NTRS2005

Model-Scale Aerodynamic Performance Testing of Proposed Modifications to the NASA Langley Low Speed Aeroacoustic Wind Tunnel

Tests were performed on a 1/20th-scale model of the Low Speed Aeroacoustic Wind Tunnel to determine the performance effects of insertion of acoustic baffles in the tunnel inlet, replacement of the existing collector with a new collector design in the open jet test section, and addition of flow splitters to the acoustic baffle section downstream of the test section. As expected, the inlet baffles caused a reduction in facility performance. About half of the performance loss was recovered by addition the flow splitters to the downstream baffles. All collectors tested reduced facility performance. However, test chamber recirculation flow was reduced by the new collector designs and shielding of some of the microphones was reduced owing to the smaller size of the new collector. Overall performance loss in the facility is expected to be a 5 percent top flow speed reduction, but the facility will meet OSHA limits for external noise levels and recirculation in the test section will be reduced.

Booth, Earl R., Jr.↗
DOE OSTI2025

Multi-scale modeling of wastage layer formation in metallic fuel cladding

Fuel-cladding chemical interaction (FCCI) is a major concern for U-Zr metallic fuels' performance, primarily due to the formation of a brittle layer (wastage) in the cladding. This brittle layer, resulting from intermetallic compounds between cladding constituents Fe, Cr, and lanthanide fission products, significantly impacts the cladding's mechanical integrity. Recent efforts focus on developing a mechanistic modeling framework to understand lanthanide production, transport to the fuel-cladding interface, and phase transformation to intermetallic phases. A multi-scale computational approach has been used to calculate lanthanide transport rates, with atomistic calculations determining Nd diffusivities through the solid fuel matrix and along pore surfaces. These diffusivities inform a mesoscale model to determine an effective diffusion coefficient, accounting for porosity and infiltration with bond sodium. This effective diffusivity is used in engineering-scale simulations via the BISON fuel performance code, which has been validated against EBR-II and FFTF reactor experiments.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Geometry Optimization of Cable-Based Actuation for Small-Scale Model Testing of a Floating Marine Turbine: Preprint

This research aims to apply combined wave and tidal current loads to a small-scale floating marine current turbine in a wave tank, where an actuation system applies hydrodynamic and mooring forces on the hardware based on results from a simulation. We use a real-time hybrid test setup with physical wave forcing from the wave tank and simulated current and mooring forces implemented through a tensioned cable array. For this paper, we developed an optimization algorithm that adjusts the hardware geometry of the cable array to achieve more efficient tension allocation across the cables for the loads that need to be actuated. By adjusting the points where the cables are attached to the floating platform and the angles between the platform and the winches, an optimal cable geometry can be found to minimize tension variations in the lines, maintain the desired pretension, and prevent excessive tensions. We present the optimization problem formulation, the actuation system evaluation approach, and optimization results that show effective cable actuation setups that are being considered for implementation in the wave tank tests.

cable-based actuation↗
DOE OSTI2026

Reservoir-scale model of geologic hydrogen production from serpentinization: Cyclic injection in a dual-permeability fracture-matrix system

Geologic hydrogen (GeoH 2 ) from serpentinization is a promising low-carbon resource, but its reservoir-scale behavior remains poorly understood. We develop a dual-permeability reactive transport model for an injector–producer well pair in ultramafic rock that couples multiphase flow, heat transfer, geochemistry, and porosity–permeability evolution. Here, the model is calibrated to olivine flow-through experiments and upscaled to two-year long simulations with continuous injection and cyclic injection with shut-in-to-injection ratios (SIR = 1, 0.5, 0.1). Olivine reacts along high-flux pathways to form lizardite and magnetite, increasing pH; H 2 (aq) and H 2 (g) peak early and then decline as exsolution and advective export outpace local generation. Continuous injection yields the highest cumulative H 2 but the lowest water-use efficiency (1.138 x 10 –6 mol/kgw). Cyclic injection increases this ratio to 1.35 x 10 –6 , 1.377 x 10 –6 , and 1.182 x 10 –6 mol/kgw for SIR = 1, 0.5, and 0.1, respectively; SIR = 0.5 provides a ~20% improvement over continuous injection and the best compromise for pilot design.

08 HYDROGEN↗
NASA NTRS1973

Results of tests OA12 and IA9 in the Ames Research Center unitary plan wind tunnels on an 0.030-scale model of the space shuttle vehicle 2A to determine aerodynamic loads, volume 1

Tests were conducted in unitary plan wind tunnels on an 0.030-scale replica of the space shuttle vehicle configuration 2A. Aerodynamic loads data were obtained at Mach numbers from 0.6 to 3.5. The investigation included tests on the integrated (launch) configuration and tests on the isolated orbiter (entry configuration). The integrated vehicle was tested at angles of attack and sideslip from minus 8 deg to plus 8 deg. The isolated orbiter was tested at angles of attack from minus 15 deg to plus 40 deg and angles of sideslip from minus 10 deg to plus 10 deg are dictated by trajectory considerations. The effects of orbiter/external tank incidence and deflected control surfaces on aerodynamic loads were also investigated.

Spangler, R. H.↗
NASA NTRS1974

Results of tests OA12 and IA9 in the Ames Research Center unitary plan wind tunnels on an 0.030-scale model of the space shuttle vehicle 2A to determine aerodynamic loads, volume 18

Tests were conducted, during April and May 1973, on an 0.030-scale replica of the Space Shuttle Vehicle Configuration 2A. Aerodynamic loads data were obtained at Mach numbers from 0.6 to 3.5. The investigation included tests on the integrated (launch) configuration, and on the isolated orbiter (entry configuration). The integrated vehicle was tested at angles of attack and sideslip from -8 degrees to +8 degrees. The isolated orbiter was tested at angles of attack from -15 degrees to +40 degrees and angles of sideslip from -10 degrees to +10 degrees as dictated by trajectory considerations. The effect of orbiter/external tank incidence angle and deflected control surfaces on aerodynamic loads were also investigated.

Spangler, R. H.↗
NASA NTRS1984

Noise and performance characteristics of a model scale X-wing rotor system in hover

Noise data for the hover condition were measured for a 8 m diameter X-wing model rotor mounted on an outdoor whirl tower. The noise was found to be a function of operating condition, in general increasing with performance. The X-wing spectra obtained from narrowband and 1/3-octave band analyses were dominated by the blade passage frequency harmonics. The circulation control slot blowing produced 1 to 10 kHz broadband noise which exhibited a jet velocity to the 5.4 dependency. Under the rotor plane loading noise was dominant, except at low values of blade pressure ratio where a sharp decrease in the blade passage frequency harmonic levels was observed. In the rotor plane, the contribution of the broadband noise sources was greater than under the rotor plane. The X-wing rotor system in hover exhibited flexibility in operating conditions to achieve a specific level of performance. The high collective, low blade passage ratio combinations which meet a given level of performance were associated with low overall sound pressure levels.

Willshire, W. L., Jr.↗
NASA NTRS1961

Stability and Control Characteristics of a Small-Scale Model of an Aerial Vehicle Supported by Two Ducted Fans

An investigation has been made to determine the stability and control characteristics in hovering and in forward flight of a free-flight model representing a type of vertical-take-off-and-landing aircraft which utilizes two fixed ducted fans as its sole source of lift and propulsion. The model, having fans 28 inches in diameter, was considered to be approximately one-third the size of a full-scale aircraft. Control moments for most of the hovering tests and all the forward-flight tests were provided by remotely controlled compressed-air jets at the sides and ends of the model. For one brief phase of the hovering investigation a system of vanes in the duct slipstreams was substituted for the jets as a means of roll control. During the forward-flight tests, the model was flown with both the tandem and side-by-side duct arrangements. In hovering the model exhibited strongly divergent oscillations about the pitch and roll axes. The pitching oscillation of the tandem configuration was of a fairly long period and was not particularly difficult to control; the rolling oscillation, however, was of a relatively short period and was extremely difficult to control. Both oscillations could be completely eliminated by the addition of a sufficient amount of artificial damping. The control moments produced by the vane-type roll control system were weak and were accompanied by a side force of appreciable magnitude and undesirable direction. In forward flight the model required an undesirably large nose-down tilt angle for equilibrium at any appreciable speed. A vane was placed transversely in the slipstream of the forward duct of the tandem configuration in an attempt to reduce this tilt angle. The vane was effective in reducing the tilt angle but apparently caused an increase in the power requirements and in the angle-of-attack instability. Without the vane, a forward speed of 30 knots (full scale) required a nose-down tilt angle of about 300. A powerful pitch control moment was required not only to maintain the trim attitude but also to 2 overcome the effects of instability with angle of attack. Less pitch control moment was required for the tandem configuration than for the side-by-side configuration at any given forward speed. The instability in roll increased with forward speed. No forward speeds in excess of about 20 knots (full scale) were achieved until the artificial damping in roll and the yaw control moment were increased appreciably above values which had proved satisfactory for hovering flight.

Parlett, Lysle P.↗
NASA NTRS1977

Results of a landing gear loads test using a 0.0405-scale model (16-0) of the space shuttle orbiter in the Rockwell International NAAL wind tunnel (OA163B), volume 1

Aerodynamic loads on a sting mounted 0.045-scale representation of the 140C outer mold line space shuttle orbiter configuration were measured to verify orbiter landing gear system pressure loading and hinge moment levels. Pressure, force, and hinge moment data, recorded over smaller increments of the landing gear deployment schedule to insure data accuracy and to investigate the effects of asymmetric gear deployment on all parameters, are presented. Tests were conducted at a Mach number of 0.17, and freestream dynamic pressure of 42.5 psf, and a Reynolds number per unit length of 1.2 million foot. Angle of attack variation was -2 to 10 degrees while angles of sideslip varied from -5 to 5 degrees.

Mennell, R. C.↗
DOE OSTI2020

Meso-scale modeling and damage analysis of carbon/epoxy woven fabric composite under in-plane tension and compression loadings

The mechanical properties and damage behaviors of carbon/epoxy woven fabric composite under in-plane tension and compression are studied at the meso-scale level through experiment and simulation. An efficient representative volume element (RVE) modeling method with consistent mesh, high yarn volume fraction and realistic geometry is proposed. The material constitutive laws with plasticity, tension-compression asymmetry and damage evolution are established for the three components - yarn, matrix and interface, respectively. Significantly different mechanical properties and damage evolutions are observed depending on loading conditions and initial geometry characteristics. It shows a non-linear stress-strain curve with clear transition region and intensive damage in tension, while a quasi-linear behavior up to facture is observed in compression with little damage prior to final fracture. Furthermore, compared to the constant Poisson's ratio with straining in compression, a dramatic increase in Poisson's ratio appears in tension. Simulation shows damage mechanisms including transverse damage, matrix damage and delamination, which all play critical roles in the property evolution. In particular, the rapid damage accumulation after elastic deformation destroys the strong bonds and causes the easy deformation of transverse yarns which results in the transition region and large Poisson's ratio in tension. All the mechanical behaviors and damage evolutions are well captured and explained with the current RVE model.

42 ENGINEERING↗
NASA NTRS1980

Tests of subgrid-scale models in strained turbulence

Strained and sheared turbulence is computed by direct simulation and it is shown that the results are in good qualitative agreement with experiments. It is found that after large amounts of strain have been applied to turbulence, the energy flow to the small scales is reduced and, in some cases, reversed. Eddy viscosity models are shown to be very poor in strained turbulence and, when they are used, the mean strain should not be included in them. Finally, new models proposed by Bardina et al. have been tested and found to offer considerable promise for the future.

Mcmillan, O. J.↗
NASA NTRS1973

Results of tests OA12 and IA9 in the Ames Research Center unitary plan wind tunnels on an 0.030-scale model of the Space Shuttle Vehicle 2A to determine aerodynamic loads, volume 9

Tests were conducted in the NASA/ARC Unitary Plan wind tunnels on an 0.030-scale replica of the space shuttle vehicle configuration 2A. Aerodynamic loads data were obtained at Mach numbers from 0.6 to 3.5. The investigation included Tests IA9A, B and C on the integrated (launch) configuration and Tests OA12A and C on the isolated orbiter (entry configuration). The integrated vehicle was tested at angles of attack and sideslip from minus 8 degrees to + 8 degrees. The isolated orbiter was tested at angles of attack from minus 15 degrees to + 40 degrees and angles of sideslip from minus 10 degrees to + 10 degrees as dictated by trajectory considerations. The effects of orbiter/external tank incidence angle and deflected control surfaces on aerodynamic loads were also investigated.

Spangler, R. H.↗
NASA NTRS1974

Results of tests 0A12 and IA9 in the Ames Research Center unitary plan wind tunnels on an 0.030 scale model of the space shuttle vehicle 2A to determine aerodynamic loads, volume 16

Tests were conducted in the NASA/ARC Unitary Plan Wind Tunnels on an 0.030 scale replica of the space shuttle vehicle Configuration 2A. Aerodynamic loads data were obtained at Mach numbers from 0.6 to 3.5. The integrated vehicle was tested at angles of attack and sideslip from -8 degrees to +8 degrees. The isolated orbiter was tested at angles of attack from -15 degrees to +40 degrees and angles of sideslip from -10 degrees to +10 degrees as dictated by trajectory considerations. The effects of orbiter/external tank incidence angle and deflected control surfaces on aerodynamic loads were also investigated.

Spangler, R. H.↗
NASA NTRS1973

Results of Tests OA12 and IA9 in the Ames Research Center unitary plan wind tunnels on an 0.030-scale model of the Space Shuttle Vehicle 2A to determine aerodynamic loads, volume 4

Tests were conducted in wind tunnels during April and May 1973, on an 0.030-scale replica of the Space Shuttle Vehicle Configuration 2A. Aerodynamic loads data were obtained at Mach numbers from 0.6 to 3.5. The investigation included tests on the integrated (launch) configuration and on the isolated orbiter (entry configuration). The integrated vehicle was tested at angles of attack and sideslip from minus 8 degrees to +8 degrees. The isolated orbiter was tested at angles of attack from minus 15 degrees to +40 degrees and angles of sideslip from minus 10 degrees to +10 degrees as dictated by trajectory considerations. The effects of orbiter/external tank incidence angle and deflected control surfaces on aerodynamic loads were also investigated.

Spangler, R. H.↗