Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructured surfaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Stress rupture and creep behavior of a low pressure plasma-sprayed NiCoCrAlY coating alloy in air and vacuum

The creep behavior of a NiCoCrAlY coating alloy in air and vacuum at 660 and 850 C is studied. The microstructure of the coating alloy is described. Analysis of the creep curves reveal that the secondary creep rates, the transition from secondary to tertiary creep, and the strain-to-failure are affected by the environment, preexposure, stress, and temperature. It is observed that the rupture lives of the NiCoCrAlY alloy at 660 and 850 C are greater in air than in vacuum. Several mechanisms that may explain the lack of crack growth from surface-connected pores during tests in air are proposed.

Hebsur, M. G.↗

Characterization of sintered SiC by using NDE

Capabilities of projection microfocus X-radiography and of ultrasonic velocity and attenuation for characterizing silicon carbide specimens were assessed. Silicon carbide batches covered a range of densities and different microstructural characteristics. Room-temperature, four-point flexural strength tests were conducted. Fractography was used to identify types, sizes, and locations of fracture origins. Fracture toughness values were calculated from fracture strength and flaw characterization data. Detection capabilities of radiography for fracture-causing flaws were evaluated. Applicability of ultrasonics for verifying material strength and toughness was examined. Radiography proved useful in detecting high-density inclusions and isolated voids, but failed in detecting surface and subsurface agglomerates and large grains as fracture origins. Ultrasonic velocity dependency on density was evident. Attenuation dependency on density and mean pore size was clearly demonstrated. Understanding attenuation as a function of toughness was limited by shortcomings in K sub IC determination.

Baaklini, George Y.↗

Design and Development of Advanced Air-Cathodes for Li-Air Battery

NASA's future missions demand high energy density batteries. Current state-of-the-art lithium-ion batteries (LIBs) reach the specific energy capacity limits (<250 Wh/kg), thus new electrochemical storage technologies are needed to meet NASA's future mission requirement of >400 Wh/kg. Battery chemistries with higher theoretical energy densities in particular, Li-metal based battery chemistries such as Li-air, are being actively pursued, but there remains a number of issues to be solved. Development of advanced and optimized air cathodes will be crucial for improving capacity retention and cycle life of Li-air battery. The microstructure of carbon substrates and the catalytic oxygen reduction of the air-cathode play critical roles in the electrochemical performance in Li-air batteries. With the development and proper design of air cathodes, the energy efficiency and energy density can be enhanced significantly. In this presentation, the results of advanced permeable air cathodes design with different substrates such as 2D carbon paper or carbon cloth, vs 3D graphene or metal foam, different high surface area carbon materials and incorporation with catalysts on oxygen reduction reactions, different porosity controlling of air cathode as well the additives in electrolyte will be presented. The cycling and rate capability performance of these air-cathodes in the Li-air cells will be discussed as well.

Wu, James J.↗

Effects of various consolidation techniques on microstructure, strength, and reliability of alpha-SiC

The effects of slurry pressing, HIP, and sinter-HIP on the strength, microstructure, and critical processing flaws in alpha-SiC are examined. Also, the feasibility of glass encapsulation is determined. Baseline strength was improved by about 25 percent by using slurry pressing instead of dry pressing. HIP further improved average strength to as high as 655 MPa. Sinter-HIP did not noticeably improve average strength. Although process-related flaws such as shrinkage cracks and large voids were not seen in HIPed alpha-SiC, surface-related flaws were observed. It is suggested that surface finishing by lapping, polishing, and heat treating might reduce the effect of surface-related flaws, improving the Weibull modulus in HIPed alpha-SiC.

Dutta, Sunil↗

Metallographic Preparation of Space Shuttle Reaction Control System Thruster Electron Beam Welds for Electron Backscatter Diffraction

A Space Shuttle Reaction Control System (RCS) thruster failed during a firing test at the NASA White Sands Test Facility (WSTF), Las Cruces, New Mexico. The firing test was being conducted to investigate a previous electrical malfunction. A number of cracks were found associated with the fuel closure plate/injector assembly (Fig 1). The firing test failure generated a flight constraint to the launch of STS-133. A team comprised of several NASA centers and other research institutes was assembled to investigate and determine the root cause of the failure. The JSC Materials Evaluation Laboratory was asked to compare and characterize the outboard circumferential electron beam (EB) weld between the fuel closure plate (Titanium 6Al-4V) and the injector (Niobium C-103 alloy) of four different RCS thrusters, including the failed RCS thruster. Several metallographic challenges in grinding/polishing, and particularly in etching were encountered because of the differences in hardness, ductility, and chemical resistance between the two alloys and the bimetallic weld. Segments from each thruster were sectioned from the outboard weld. The segments were hot-compression mounted using a conductive, carbon-filled epoxy. A grinding/polishing procedure for titanium alloys was used [1]. This procedure worked well on the titanium; but a thin, disturbed layer was visible on the niobium surface by means of polarized light. Once polished, each sample was micrographed using bright field, differential interference contrast optical microscopy, and scanning electron microscopy (SEM) using a backscatter electron (BSE) detector. No typical weld anomalies were observed in any of the cross sections. However, areas of large atomic contrast were clearly visible in the weld nugget, particularly along fusion line interfaces between the titanium and the niobium. This prompted the need to better understand the chemistry and microstructure of the weld (Fig 2). Energy Dispersive X-Ray Spectroscopy (EDS) was used to confirm the chemical composition of the variations in contrast in these areas. Niobium alloys generally require exposure to more aggressive chemical reagents than titanium alloys for etching because of niobium s chemical resistance; therefore, the titanium portion of the sample was etched first. A five second immersion in Kroll s reagent revealed a general microstructure on the titanium portion of the sample; however, the titanium heat affected zone closest to the weld, was over-etched due to higher concentrations of refined grains and an increase in eta-phase. The Kroll s etchant also revealed some microstructure in the weld nugget itself; the niobium portion of the sample remained unetched.

Martinez, James↗

Durability Assessment of TiAl Alloys

The durability of TiAl is a prime concern for the implementation of TiAl into aerospace engines. Two durability issues, the effect of high temperature exposure on mechanical properties and impact resistance, have been investigated and the results are summarized in this paper. Exposure to elevated temperatures has been shown to be detrimental to the room temperature ductility of gamma alloys with the most likely mechanisms being the ingress of interstitials from the surface. Fluorine ion implantation has been shown to improve the oxidation resistance of gamma alloys, and ideally it could also improve the environmental embrittlement of high Nb content TiAl alloys. The effect of F ion implantation on the surface oxidation and embrittlement of a third generation, high Nb content TiAl alloy (Ti-45Al-5Nb-B-C) were investigated. Additionally, the ballistic impact resistance of a variety of gamma alloys, including Ti-48Al-2Cr- 2Nb, Ti-47Al-2Cr-2Nb, ABB-2, ABB-23, NCG359E, 95A and Ti-45Al-5Nb-B-C was accessed. Differences in the ballistic impact properties of the various alloys will be discussed, particularly with respect to their manufacturing process, microstructure, and tensile properties.

Draper, Susan L.↗

A study of the microstructure of a rapidly solidified nickel-base superalloy modified with boron

The microstructures of melt-spun superalloy ribbons with variable boron levels have been studied by transmission electron microscopy. The base alloy was of approximate composition Ni-11% Cr-5%Mo-5%Al-4%Ti with boron levels of 0.06, 0.12, and 0.60 percent (all by weight). Thirty micron thick ribbons display an equiaxed chill zone near the wheel contact side which develops into primary dendrite arms in the ribbon center. Secondary dendrite arms are observed near the ribbon free surface. In the higher boron bearing alloys, boride precipitates are observed along grain boundaries. A concerted effort has been made to elucidate true grain shapes by the use of bright field/dark field microscopy. In the low boron alloy, grain shapes are often convex, and grain faces are flat. Boundary faces frequently have large curvature, and grain shapes form concave polygons in the higher boron level alloys. It is proposed that just after solidification, in all of the alloys studied, grain shapes were initially concave and boundaries were wavy. Boundary straightening is presumed to occur on cooling in the low boron alloy. Boundary migration is precluded in the higher boron alloys by fast precipitation of borides at internal interfaces.

Speck, J. S.↗

Creep life prediction based on stochastic model of microstructurally short crack growth

A nondimensional model of microstructurally short crack growth in creep is developed based on a detailed observation of the creep fracture process of 304 stainless steel. In order to deal with the scatter of small crack growth rate data caused by microstructural inhomogeneity, a random variable technique is used in the model. A cumulative probability of the crack length at an arbitary time, G(bar a, bar t), and that of the time when a crack reaches an arbitary length, F(bar t, bar a), are obtained numerically by means of a Monte Carlo method. G(bar a, bar t), and F(bar t, bar a) are the probabilities for a single crack. However, multiple cracks generally initiate on the surface of a smooth specimen from the early stage of creep life to the final stage. TAking into account the multiple crack initiations, the actual crack length distribution observed on the surface of a specimen is predicted by the combination of probabilities for a single crack. The prediction shows a fairly good agreement with the experimental result for creep of 304 stainless steel at 923 K. The probability of creep life is obtained from an assumption that creep fracture takes place when the longest crack reaches a critical length. The observed and predicted scatter of the life is fairly small for the specimens tested.

Kitamura, Takayuki↗

Creep life prediction based on stochastic model of microstructurally short crack growth

A nondimensional model of microstructurally short crack growth in creep is developed based on a detailed observation of the creep fracture process of 304 stainless steel. In order to deal with the scatter of small crack growth rate data caused by microstructural inhomogeneity, a random variable technique is used in the model. A cumulative probability of the crack length at an arbitrary time, G(bar a, bar t), and that of the time when a crack reaches an arbitrary length, F(bar t, bar a), are obtained numerically by means of a Monte Carlo method. G(bar a, bar t), and F(bar t, bar a) are the probabilities for a single crack. However, multiple cracks generally initiate on the surface of a smooth specimen from the early stage of creep life to the final stage. Taking into account the multiple crack initiations, the actual crack length distribution observed on the surface of a specimen is predicted by the combination of probabilities for a single crack. The prediction shows a fairly good agreement with the experimental result for creep of 304 stainless steel at 923 K. The probability of creep life is obtained from an assumption that creep fracture takes place when the longest crack reaches a critical length. The observed and predicted scatter of the life is fairly small for the specimens tested.

Kitamura, Takayuki↗

A preliminary characterization of the tensile and fatigue behavior of tungsten-fiber/Waspaloy-matrix composite

A microstructural study and a preliminary characterization of the room temperature tensile and fatigue behavior of a continuous, tungsten fiber, Waspaloy-matrix composite was conducted. A heat treatment was chosen that would allow visibility of planar slip if it occurred during deformation, but would not allow growth of the reaction zone. Tensile and fatigue tests showed that the failed specimens contained transverse cracks in the fibers. The cracks that occurred in the tensile specimen were observed at the fracture surface and up to approximately 4.0 mm below the fracture surface. The crack spacing remained constant along the entire length of the cracked fibers. Conversely, the cracks that occurred in the fatigue specimen were only observed in the vicinity of the fracture surface. In instances where two fiber cracks occurred in the same plane, the matrix often necked between the two cracked fibers. Large groups of slip bands were generated in the matrix near the fiber cracks. Slip bands in the matrix of the tensile specimen were also observed in areas where there were no fiber cracks, at distances greater than 4 mm from the fracture surface. This suggests that the matrix plastically flows before fiber cracking occurs.

Corner, Ralph E.↗

Electrostatic Levitation: A Tool to Support Materials Research in Microgravity

Containerless processing represents an important topic for materials research in microgravity. Levitated specimens are free from contact with a container, which permits studies of deeply undercooled melts, and high-temperature, highly reactive materials. Containerless processing provides data for studies of thermophysical properties, phase equilibria, metastable state formation, microstructure formation, undercooling, and nucleation. The European Space Agency (ESA) and the German Aerospace Center (DLR) jointly developed an electromagnetic levitator facility (MSL-EML) for containerless materials processing in space. The electrostatic levitator (ESL) facility at the Marshall Space Flight Center provides support for the development of containerless processing studies for the ISS. Apparatus and techniques have been developed to use the ESL to provide data for phase diagram determination, creep resistance, emissivity, specific heat, density/thermal expansion, viscosity, surface tension and triggered nucleation of melts. The capabilities and results from selected ESL-based characterization studies performed at NASA's Marshall Space Flight Center will be presented.

Rogers, Jan↗

Effects of Microstructural Variability on Thermo-Mechanical Properties of a Woven Ceramic Matrix Composite

The objectives of this paper include identifying important architectural parameters that describe the SiC/SiC five-harness satin weave composite and characterizing the statistical distributions and correlations of those parameters from photomicrographs of various cross sections. In addition, realistic artificial cross sections of a 2D representative volume element (RVE) are generated reflecting the variability found in the photomicrographs, which are used to determine the effects of architectural variability on the thermo-mechanical properties. Lastly, preliminary information is obtained on the sensitivity of thermo-mechanical properties to architectural variations. Finite element analysis is used in combination with a response surface and it is shown that the present method is effective in determining the effects of architectural variability on thermo-mechanical properties.

Goldsmith, Marlana B.↗

Structure and grain coarsening during the sintering of alumina

The pore surface area (Sp) and grain-boundary area (Sgb) were measured during the sintering of undoped and doped (100 ppm MgO) alumina compacts. Since the presence of the additive affects only Sgb (raising it at a given value of the density), pinning of the boundaries by solid-solution drag is the only additive function evidenced by the results. The importance of such pinning even at densities as low as 75 percent of theoretical is linked to the existence of microstructural inhomogeneities.

Shaw, N. J.↗

Space Weathering of Olivine in Lunar Soils: A Comparison to Itokawa Regolith Samples

Regolith particles from airless bodies preserve a record of the space weathering processes that occurred during their surface exposure history. These processes have major implications for interpreting remote-sensing data from airless bodies. Solar wind irradiation effects occur in the rims of exposed grains, and impact processes result in the accumulation of vapordeposited elements and other surface-adhering materials. The grains returned from the surface of Itokawa by the Hayabusa mission allow the space weathering "style" of a chondritic, asteroidal "soil" to be compared to the lunar case. Here, we present new studies of space-weathered olivine grains from lunar soils, and compare these results to olivine grains from Itokawa. Samples and Methods: We analyzed microtome thin sections of olivine grains from the 20-45 micron fractions of three lunar soils: 71061, 71501 and 10084 (immature, submature and mature, respectively). Imaging and analytical data were obtained using a JEOL 2500SE 200kV field-emission scanning-transmission electron microscope equipped with a thin-window energy-dispersive x-ray spectrometer. Similar analyses were obtained from three Hayabusa olivine grains. Results and Discussion: We observed lunar grains showing a range of solar flare track densities (from <10(exp 9) to approx.10(exp 12)/sq cm). The lunar olivines all show disordered, highly strained, nanocrystalline rims up to 150-nm thick. The disordered rim thickness is positively correlated with solar flare track density. All of the disordered rims are overlain by a Si-rich amorphous layer, ranging up to 50-nm thick, enriched in elements that are not derived from the host olivine (e.g., Ca, Al, and Ti). The outmost layer represents impact-generated vapor deposits typically observed on other lunar soil grains. The Hayabusa olivine grains show track densities <10(exp 10)/sq cm and display disordered rims 50- to 100-nm thick. The track densities are intermediate to those observed in olivines in immature and submature lunar soils and indicate surface exposures of approx. 10(exp 5) years. The outermost few nanometers of the disordered rims on Hayabusa olivines are more Si-rich and Mg- and Fe-depleted relative to the cores of the grains and likely represent a minor accumulation of impact-generated vapors or sputter deposits. Nanophase Fe metal particles are less abundant in the Hayabusa rims compared to the rims on lunar grains. Conclusions: The Hayabusa and lunar olivine grain rims have widths and microstructures consistent with formation from atomic displacement damage from solar wind ions. The space weathering features in the Hayabusa grains are similar to those observed in olivines from immature to submature lunar soils. A major difference, however, is that the Hayabusa grains appear to lack the hypervelocity impact products (melt spherules, thick vapor deposits, and abundant nanophase Fe metal particles) that are common in lunar soil grains with a similar exposure history.

Keller, L. P.↗

Measurements of radiated elastic wave energy from dynamic tensile cracks

The role of fracture-velocity, microstructure, and fracture-energy barriers in elastic wave radiation during a dynamic fracture was investigated in experiments in which dynamic tensile cracks of two fracture cofigurations of double cantilever beam geometry were propagating in glass samples. The first, referred to as primary fracture, consisted of fractures of intact glass specimens; the second configuration, referred to as secondary fracture, consisted of a refracture of primary fracture specimens which were rebonded with an intermittent pattern of adhesive to produce variations in fracture surface energy along the crack path. For primary fracture cases, measurable elastic waves were generated in 31 percent of the 16 fracture events observed; the condition for radiation of measurable waves appears to be a local abrupt change in the fracture path direction, such as occurs when the fracture intersects a surface flaw. For secondary fractures, 100 percent of events showed measurable elastic waves; in these fractures, the ratio of radiated elastic wave energy in the measured component to fracture surface energy was 10 times greater than for primary fracture.

Boler, Frances M.↗

Characterizing TPS Microstructure: A Review of Some techniques

I. When seeking to understand ablator microstructure and morphology there are several useful techniques A. SEM 1) Visual characteriza3on at various length scales. 2) Chemical mapping by backscatter or x-ray highlights areas of interest. 3) Combined with other techniques (density, weight change, chemical analysis) SEM is a powerful tool to aid in explaining thermo/structural data. B. ASAP. 1) Chemical characteriza3on at various length scales. 2) Chemical mapping of pore structure by gas adsorption. 3) Provides a map of pore size vs. pore volume. 4) Provided surface area of exposed TPS. II. Both methods help characterize and understand how ablators react with other chemical species and provides insight into how they oxidize.

Gasch, Matthew↗

An Exploratory Study of the Microstructure of Mullite Fibers

The microstructures of mullite composition fibers were examined by transmission electron microscopic techniques and by X-ray diffraction analyses. Both spun and monofilament fiber structures contained little porosity, nor did the degree of porosity change after heating the monofilament to 1205 C for one half hour. Thermal exposure produced crystallite growth and nucleation from the amorphous phase in all three of the spun fibers. After 116 hours at 1426 C, the crystallites of the standard spun fibers became contiguous. In addition, the surface crystallites of these fibers were found to be more than twice as large as the interior crystallites.

Santoro, G.↗

Data use investigations for applications Explorer Mission A (Heat Capacity Mapping Mission): HCMM's role in studies of the urban heat island, Great Lakes thermal phenomena and radiometric calibration of satellite data

The utility of data from NASA'a heat capacity mapping mission satellite for studies of the urban heat island, thermal phenomena in large lakes and radiometric calibration of satellite sensors was assessed. The data were found to be of significant value in all cases. Using HCMM data, the existence and microstructure of the heat island can be observed and associated with land cover within the urban complex. The formation and development of the thermal bar in the Great Lakes can be observed and quantitatively mapped using HCMM data. In addition, the thermal patterns observed can be associated with water quality variations observed both from other remote sensing platforms and in situ. The imaging radiometer on-board the HCMM satellite is shown to be calibratible to within about 1.1 C of actual surface temperatures. These findings, as well as the analytical procedures used in studying the HCMM data, are included.

Schott, J. R.↗