SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Low temperature sintering enables dense composites of ceramic active materials and conductive agents. Conductivity and microstructure of composites is characterized.
There is an increased interest in topologically nontrivial magnetic spin textures such as skyrmions and chiral domain-wall solitons, both from a point of fundamental physics understanding as well as potential technological interest in low-power memory applications. In order to control their behavior, it is necessary to understand their complex spin texture at the nanoscale. Lorentz transmission electron microscopy (LTEM) is a suitable technique for studying these systems due to its high spatial resolution and capability to simultaneously characterize magnetic texture and microstructure. In this work, we present the application of PyLorentz, an open-source software suite that we have developed, for quantitative image analysis of Neel-type skyrmions in thin-film heterostructures. PyLorentz enhances LTEM capabilities by enabling reconstruction of magnetic induction maps from experimental images, as well as simulating LTEM images using micromagnetic simulation data. We demonstrate this for simulated Neel skyrmions as well as experimental data from [Pt/Co/W] multilayer heterostructures. Finally, we also show how simulation-assisted LTEM analysis is crucial for understanding these complex magnetic spin textures, in which the reconstructed magnetic induction map (seen in the LTEM images) differs significantly from the magnetization configuration.
Abstract The objective of this work is to study friction surfacing process variability when depositing multilayered coatings. This is motivated by the need to maintain deposition quality when depositing multiple friction surfacing layers, whether for repair, remanufacturing, or new part creation using this solid-state metal additive manufacturing process. In this study, 10-mm-diameter 304L stainless steel rods were used to create up to five layers of 40-mm-long coatings on 304L substrates using a constant set of processing parameters. In-process measurement of forces (X, Y, Z), flash temperature, flash geometry, layer temperature, and post-process measurement of layer geometry, microhardness, and microstructure are used to characterize changes in the friction surfacing process as more layers are deposited. It was observed that with increasing layers: layer thickness and deposition efficiency decrease; offsetting of the deposition towards the retreating side, and temperature in the deposited layer increase; and flash temperature does not change. Metallurgical analyses of friction-surfaced cross-sections revealed fine grain refinement and transformation of base austenite to strain-induced martensite. It is concluded that the process parameters need to be adjusted even after the second or third layer is deposited, corrections to the tool path are required after a couple of layers, and the measured process forces, as well as deposited layer temperature, may be useful to monitor and control the process and its instabilities.
Low density, high strength, and high creep and oxidation resistance properties of ceramic matrix composites (CMCs) make them an ideal choice for use in extreme environments in space and military applications. This paper presents a detailed characterization study of structural and manufacturing flaws in Carbon fiber Silicon-Carbide-Nitride matrix (C/SiNC) CMCs at different length-scales. Energy-dispersive spectroscopy (EDS) is used for the chemical characterization of the material’s elemental constituents. High-resolution multiscale graphs obtained from scanning electron microscope (SEM) and confocal laser scanning microscope (LSM) are used to characterize the distribution and morphology of defects at different length scales. This is followed by the classification and quantification of the common manufacturing defects. An image processing algorithm based on the image segmentation process is developed to quantify the variability of various scale-dependent architectural parameters. Finally, a three-dimensional stochastic representative volume element (SRVE) generation algorithm is developed to provide precise representations of material textures at multiple length scales. The developed algorithm accurately accounts for material features and flaws based on a range of multiscale structural and defects characterization results.
Uranium alloyed with 50 wt% zirconium (U-50Zr) is a proposed light water reactor (LWR) nuclear fuel by Lightbridge Corporation (LTBR). The proposed method for making the U-50Zr alloy is to arc-melt master alloys and then remelt in a vacuum induction melter (VIM) to consolidate the material and cast into an intermediate shape. After casting, the material will eventually need to be formed into a desired fuel shape. The work discussed in this report resulted from a joint effort between Ltbr and Pacific Northwest National Laboratory (PNN) to investigate a 500g – 1kg scale casting process to produce the U-50Zr alloy in the desired δ-UZr 2 phase and characterize the impurities and microstructure that result from the casting process. Master alloys were fabricated in an arc melter, then five castings were carried out in a VIM with multiple inert coating and crucible materials to find an appropriate combination. Both ZrO 2 and graphite crucibles were used and different combinations of Y 2 O 3 , CaZrO 3 , and TiC to identify which would contain the molten metal with the least reaction. On each casting, the C, O, N, H impurities were analyzed as well as the phase by x-ray diffraction and microstructure. Of the five castings, two resulted in majority of δ-UZr 2 phase-pure material and had impurity levels within acceptable ranges. The two most successful castings utilized a graphite crucible with a TiC undercoating and a Y 2 O 3 overcoat. The O and N levels were below 1000 ppm and the C content was variable but did not result in measurable carbide formation. The highest success casting resulted in an average of 282 ppm C, 567 ppm O, 217 ppm N and 79 ppm H. This casting's crucible and inert coating material was repeated with slightly different casting parameters and resulted in higher C numbers but similar phase identification. The differences between each casting are discussed and recommendations are made for future experiments to better decide on a casting process to go forward with.
Advanced cladding is critical for advanced nuclear reactors with an enhanced performance in radiation tolerance and neutron transparency. Using advanced cladding will ensure the adequate thermal conductivity and mechanical stability of the cladding base material, corrosion resistance, high-temperature coolant compatibility of the cladding surface, and chemical stability in the cladding inner wall against fuel cladding chemical interaction (FCCI). An innovative cladding with a three-layer structure (i.e., a modified surface, a clad base material, and a modified inner wall) promises to meet all these requirements. Initial research and development (R&D) regarding this innovative cladding seek to demonstrate the effectiveness of a thin ceramic coating in suppressing FCCI under ion irradiation to high dose. This United States (U.S.) Department of Energy (DOE)–Office of Nuclear Energy (NE) project report summarizes the results of recent ion irradiation studies of diffusion-couple samples with details of an ion irradiation experiment, the characterization of the interface microstructure of cerium (Ce)/titanium nitride (TiN)/oxide-dispersion strengthened (ODS), Ce/TiN/iron (Fe), Ce/ODS, and Ce/Fe samples irradiated with 80 million electron-volts (MeV) of xenon (Xe) ions to 100 displacements per atom (dpa) at 500?C using the Argonne Tandem Linac Accelerator System (ATLAS) facility at Argonne National Laboratory (ANL). The results of the ODS-substrate sample are encouraging and demonstrate the effectiveness of a thin ceramic coating on FCCI mitigation under irradiation. The results from an Fe-substrate sample revealed a complex microstructure, and the root cause is discussed.
Bonded composite π-joints are critical to support wing geometries in aerospace/aircraft structures. Its lightweight and robust load-bearing capabilities/design guarantee high structural integrity and reliability. Current manufacturing techniques of π-joints are complex and laborious, and do not always offer high-quality joining. This study presents a high-rate manufacturing approach to fabricate π-joints using an integrated Additive Manufacturing and Compression Molding (AMCM) process. The joints were manufactured using unidirectional aerospace-grade LMPAEK/CF at 60% fiber loading for the stiffeners/skin and LM-PAEK/GF as the adhesive and characterized to evaluate their microstructure and strength. While the results indicate void formation at the joint caused by inadequate pressure, the peak tensile load of 600N recorded is akin to injection-autoclave molded π-joints, which validates the potential of this high-rate integrated approach to eliminate time-consuming and labour-intensive processes of making π-joints to reduce cost and produce high-quality joints.
Adhesive bonding requires adequate surface preparation for ensuring an appropriate joint quality. The interest in adhesive joining has recently expanded to thermal systems having a large number of joints employed for manufacturing and assembly. This study presents surface topology of copper 110 produced by a laser-interference setup that would theoretically yield a periodicity of 1.7 μm, which is near the 1.6–2 μm structuring limit that was estimated based on thermal diffusion length scale for an 8 ns laser pulse. The results show that although the expected periodic interference structuring was not attained, the melt-induced texturing was affected by the laser-interference profile. Single-lap shear tests were performed with specimen surfaces prepared by traditional abrasion and laser-interference structuring methods. Several laser processing parameters, such as the laser spot size, density, number of pulses, and raster speed, were studied. Scanning electron microscope and profilometry measurements were used to characterize the processed surface microstructures. Web-like structures, which indicate widespread melting, were shown to be formed at different processing conditions. Based on the surface topologies investigated, two laser raster speeds were selected to make single-lap-joint specimens. Baseline joints were prepared by abrading joining specimens. The shear-lap strength and displacement at maximum load were shown to be higher by 16.8% and 43.8% for the laser-structured specimens than those of the baseline specimens, respectively. Moreover, the load-displacement curves indicated that the laser-structured joints were more ductile than those without laser-structuring. The increased ductility for the laser-structured joints was found to yield an increase in the energy absorbed during shear-lap testing of approximately of 80–90% over those measured for baseline joints. It is another indicator that laser-interference structuring enhanced the bonding performance of single-lap shear joints.
Explore the source record for details and available documents.
Graphene oxide (GO) membranes intercalated with various organic moieties have shown excellent potential for a range of water processing applications. However, microstructure–functional property relationships in these structurally disordered membranes are not well understood. We demonstrate a practical methodology for developing such relationships for GO membranes intercalated with molecular species, with polycyclic aromatic toluidine blue O (TBO) as an example functional intercalant. We use solid-state UV–vis absorbance and fluorescence measurements to quantitatively track the arrangements of TBO in a series of TBO-loaded reduced GO (rGO) membranes. This study reveals the evolution of diverse arrangements including TBO monomers, lateral and stacked dimers, and other aggregates, as a function of overall TBO loading. These microstructures are then correlated to changes in overall properties such as interlayer d-spacings, permeate fluxes, and solute rejections. The characterization of these different intercalant microstructures explains non-intuitive flux and rejection trends, which can circumvent flux and solute rejection trade-offs.
Friction stir welding (FSW) is a solid-state joining process that minimizes the heat-affected zone (HAZ) compared with fusion-based arc welding, making it well suited for joining martensitic armor steels where hardness and ballistic resistance are critical. This study investigates residual stress formation in three defect-free FSW butt-joint configurations relevant to armored-vehicle fabrication: similar rolled homogeneous armor (RHA–RHA, Case 1), similar high-hardness armor (HHA–HHA, Case 2), and dissimilar HHA–RHA (Case 3) joints produced under temperature-controlled conditions (770 °C). Neutron diffraction was employed to quantify the magnitude and spatial distribution of residual stresses in the longitudinal, transverse, and normal directions and to correlate them with weld microstructure and hardness. Tensile residual stresses were concentrated in the softened HAZ, reaching approximately 300 MPa for Case 2 and 400 MPa for Case 1 (≈50–70 % of the base-metal yield strength; ∼581 MPa for RHA and ∼566 MPa for HHA), while compressive residual stresses dominated the stir zone. The spatial extent of tensile stresses scaled with the width of the softened HAZ, which was largest in the dissimilar HHA–RHA joint and smallest in the HHA–HHA joint. Full-width-at-half-maximum (FWHM) analysis revealed low microstrain in overtempered HAZ regions and high microstrain in the stir zone associated with severe plastic deformation and fresh martensite formation. This work demonstrates that residual stress evolution in FSW of martensitic armor steels is governed not primarily by peak temperature or thermal contraction, as inferred from fusion-welding analogies, but by the competition between transformation-induced volumetric expansion and tempering-induced stress relaxation. The relative dominance of these mechanisms is shown to depend on alloy hardenability and local thermal history, leading to more extensive HAZ softening and broader tensile stress regions in the lower-hardenability RHA steel. These findings establish a transferable mechanistic framework for optimizing solid-state joining strategies in high-strength steels and other transformation-hardening alloys beyond armor applications.
Abstract Ni- and Co-based M–Cr–Al–Y (M = Ni and/or Co), dual phase β and γ/γ′, β—Ni–Al, γ—Ni(Co, Cr), and γ′—Ni3–Al superalloys exhibit several beneficial high-temperature (>1000 °C) (2012 °F) strength and corrosion resistance properties. Our study investigates the feasibility of fabricating a commercially available Ni–Co–Cr–AlY alloy (tradename “Amdry 386”) using laser directed energy deposition (laser-DED). A significant challenge for laser fabrication of bulk Amdry 386 (A386) structures stems from the presence of relatively higher amounts of the β phase than γ/γ′ phases. While prior studies report laser fabrication of these materials in coating and cladding configurations, bulk structures have not been realized. To investigate these challenges, this study was developed to systematically evaluate the effects of modifying the A386 alloy by adding 10, 20, and 30% by weight of a Ni–20%Cr (Ni–Cr) alloy (mainly γ/γ′). Laser-DED-fabricated A386 coupons exhibited a metastable, rapidly solidified β-rich microstructure typical to laser processes. The A386 + Ni–Cr mixtures were processed using laser-DED, and small coupons from each composition were evaluated using SEM, XRD, and microhardness to characterize the as-processed microstructure. Thermodynamic modeling was performed to determine the phase evolution as a function of the alloy composition. The dominating phase switches from β to γ/γ’ between the A386 and A386 + 10% Ni–Cr mixtures, but the increase in structural integrity is not observed until the Ni–Cr additions reach a minimum of 20%. Our results show that the alloy chemistry can be successfully modified to improve the structural integrity of laser-processed structures.
In this project, a synergistic approach involving experiments informed by modelling was used to develop γ'/γ'' coprecipitation-strengthened Ni-base superalloys for land-based gas turbine wheels. In thick sections of such turbine wheels, the slow cooling rate normally observed, as well as variations in cooling rate could potentially result in drastically inhomogeneous and coarsened microstructure. Thus, ten alloy compositions were selected based on coprecipitation and sluggish γ’ growth and coarsening during three iterations of alloy development, assisted by extensive CALPHAD modeling. Phase equilibrium calculations, informed by the characterization of early alloys, were successful in predicting suitable aging treatments to obtain bimodal coprecipitate distribution in several alloys. These aging treatments were applied to the subsequent round of alloys and the resulting microstructures were characterized in detail. Two different cooling rates were used during each of these heat treatments to simulate the range of cooling rates observed in a thick section forging. The microstructures were used to calibrate a multi-phase field model (MPF), which was used to study the formation mechanisms of various coprecipitate morphologies observed in the experiments. Following this, the most promising alloys in each round were selected and studied using high temperature tensile and creep tests. Considering that a slower cooling rate would lead to a strength debit, while a faster cooling rate might lead to a decline in creep rupture life of a full-scale wheel, tensile tests were carried out for slower cooled samples, while creep tests were carried out for faster cooled samples. The deformation microstructures were then characterized using advanced characterization techniques such as Diffraction Contrast-Scanning Transmission Electron Microscopy (DC-STEM) and Electron Channeling Contrast Imaging (ECCI). Further, a mean-field creep model was developed and calibrated using these experimental findings to predict long-term creep behavior of these coprecipitation-strengthened alloys.
Abstract Structural metallic materials with interfaces of immiscible materials provide opportunities to design and tailor the microstructures for desired mechanical behavior. Metallic microstructures with plasticity contributors of the FCC and BCC phases show significant promise for damage-tolerant applications due to their enhanced strengths and thermal stability. A fundamental understanding of the dynamic failure behavior is needed to design and tailor these microstructures with desired mechanical responses under extreme environments. This study uses molecular dynamics (MD) simulations to characterize plasticity contributors for various interface microstructures and the damage evolution behavior of FCC/BCC laminate microstructures. This study uses six model Cu/Ta interface systems with different orientation relationships that are as- created, and pre-deformed to understand the modifications in the plasticity contributions and the void nucleation/evolution behavior. The results suggest that pre-existing misfit dislocations and loading orientations (perpendicular to and parallel to the interface) affect the activation of primary and secondary slip systems. The dynamic strengths are observed to correlate with the energy of the interfaces, with the strengths being highest for low-energy interfaces and lowest for high-energy interfaces. However, the presence of pre-deformation of these interface microstructures affects not only the dynamic strength of the microstructures but also the correlation with interface energy.
A set of novel uranium-based alloys has been proposed for use in advanced LEU fuel systems. This study seeks to develop methods to fabricate single-phase alloys and evaluate the compatibilities of the alloys for use in composite fuel systems. The as-cast microstructure of each alloy was characterized via scanning electron microscopy (SEM), and candidate alloys were further down-selected for homogenization and interaction testing. The U 22 Zr 20 Nb 58 alloy was successfully fabricated as a single-phase system, as demonstrated via X-ray diffraction (XRD) and SEM. The thermal and mechanical properties of the U-Nb-Zr alloy were further assessed via differential scanning calorimetry (DSC), laser flash analysis (LFA), and Vickers’ micro-hardness testing. This alloy also demonstrated improved compatibility with fuel candidate alloys from conventional matrix materials and may be a viable option for use in advanced fuel systems.
Abstract The purpose of this research work is to characterize and inform the design of (mechanical) property-graded bulk structures made from a single metallic alloy via a laser powder bed fusion (LPBF) process, with an end goal of creating repeatable/reproducible functionally-graded additively manufactured (FGAM) parts. This paper specifically investigates the manufacture of stainless steel (SS) 316L structures via a pulsed selective laser melting (SLM) process, and the underlying causes of property variations (within a functionally-acceptable range) through various material characterization techniques. For this, a design of experiments spanning the volumetric energy density (VED) based process parameter design space was utilized to investigate the range of functionally-acceptable physical/mechanical properties achievable in SS 316L. Five sample conditions (made via different process parameter combinations) were down-selected for in-depth microstructure analysis and mechanical/physical property characterization; these were suitably selected to impart a wide and controllable property range (209–318 HV hardness, 90–99.9% relative density, and 154–211 GPa modulus). It was observed that property variations resulted from combinations of porosity types/amounts, martensitic phase fractions, and grain sizes. Based on these findings, property-graded standard test specimens were designed and manufactured for further investigation—tensile specimens having a monotonic hardness change along its gauge length, four-point bending specimens with varying elastic moduli as a function of the distance from the neutral axis, and Moore’s rotating beam fatigue specimens with moduli variations based on the distance from the center. Altogether, this work lays the foundation for understanding and designing the local and global mechanical performance of FGAM bulk structures.
In this study, the corrosion behavior of the Al x CoCrFeNi (x = 0.3, 0.5, 0.7) high-entropy alloys (HEAs) is investigated by an in-situ visualization system. Surface morphology changes on both micro-spatial and temporal scales are monitored in the 3.5 wt% NaCl solution during the potentiodynamic polarization. The microstructures of the Al x CoCrFeNi HEAs are characterized by SEM, EBSD, and EDS. The results show that the microstructure evolves from singe face-centered cubic (FCC) phase to multi-phases by increasing the Al content. The in-situ observations directly reveal the different localized corrosion processes in the AlxCoCrFeNi HEAs. In the single FCC phase Al 0.3 CoCrFeNi HEA, localized corrosion shows in the form of pitting. In the Al 0.5 CoCrFeNi and Al 0.7 CoCrFeNi alloys, which possess FCC and body-centered cubic (BCC) phases, the localized corrosion initiates and propagates in the Cr-depleted BCC phase. In addition, the in-situ visualization uncovers the evolution of current serration, which represents the propagation and repassivation of metastable pit during the polarization. The frequent occurrence of metastable pits indicates distinct repassivation ability of the Al 0.3 CoCrFeNi HEA.
Three high–intermetallic volume Nb–Si–Cr–(Mo) alloys were designed using CALPHAD modeling with the goal of identifying high–specific strength, oxidation-resistant alloys that can be additively manufactured using powder bed fusion. The silicides Nb 5 Si 3 and Nb 9 Si 2 Cr3 were targeted as the primary strengthening phases, and the addition of Cr promoted the NbCr 2 phase. These alloys were cast and surface-processed with electron beam welding at different speeds to simulate additive manufacturing, and the phases and microstructures of both cast and welded regions were characterized. The weld processing was found to produce fine-grained microstructures in each alloy with fine-scale intermetallics uniformly distributed among a body-centered cubic Nb matrix. Microstructural refinement and hardness were found to increase with weld velocity; one alloy reached its highest hardness of approximately 16 GPa before the brittleness at higher velocities became detrimental. One alloy was found to be qualitatively the least brittle while also attaining a hardness of 13 GPa and was therefore identified as a good candidate for additive manufacturing.