Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “maximum”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

How does humidity data impact land surface modeling of hydrothermal regimes at a permafrost site in Utqia$\mathrm{\dot{g}}$vik, Alaska?

Humidity is a basic and crucial meteorological indicator commonly measured in several forms, including specific humidity, relative humidity, and absolute humidity. These different forms can be inter-derived based on the saturation vapor pressure (SVP). In past decades, dozens of formulae have been developed to calculate the SVP with respect to, and in equilibrium with, liquid water and solid ice surfaces, but many prior studies use a single function for all temperature ranges, without considering the distinction between over the liquid water and ice surfaces. These different approaches can result in humidity estimates that may impact our understanding of surface-subsurface thermal-hydrological dynamics in cold regions. In this study, we compared the relative humidity (RH) downloaded and calculated from four data sources in Alaska based on five commonly used SVP formulas. These RHs, along with other meteorological indicators, were then used to drive physics-rich land surface models at a permafrost-affected site. Here, we found that higher values of RH (up to 40%) were obtained if the SVP was calculated with the over-ice formulation when air temperatures were below freezing, which could lead to a 30% maximum difference in snow depths. The choice of whether to separately calculate the SVP over an ice surface in winter also produced a significant range (up to 0.2 m) in simulated annual maximum thaw depths. The sensitivity of seasonal thaw depth to the formulation of SVP increases with the rainfall rate and the height of above-ground ponded water, while it diminishes with warmer air temperatures. These results show that RH variations based on the calculation of SVP with or without over-ice calculation meaningfully impact physically-based predictions of snow depth, sublimation, soil temperature, and active layer thickness. Under particular conditions, when severe flooding (inundation) and cool air temperatures are present, care should be taken to evaluate how humidity data is estimated for land surface and earth system modeling.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Metal-embedded fiber optic sensor packaging and signal demodulation scheme towards high-frequency dynamic measurements in harsh environments

Optical fiber-based sensors are commonly used for industrial monitoring and control processes due to their small size, resistance to electromagnetic interference, and ability to perform a wide variety of high-precision measurements. However, implementing optical fiber sensors in harsh environments is challenging because they are small and fragile. Proper packaging of fiber-optic sensors could extend their use to harsh environments, including at high temperature and under high radiation. Furthermore, conventional fiber optic-based measurement systems often use computationally expensive signal processing algorithms which hinder their use in high-frequency dynamic applications. This work reports on the design of an optical fiber-pressure sensor system based on low-coherence interferometry that uses a metal-embedded optical fiber to provide a robust sensor package. Additionally, a novel phase demodulation scheme is proposed to extract length changes from the deformation of a thin diaphragm within a Fabry–Pérot cavity to measure pressure. The sensor has been tested to ±100 kPa, has a theoretical linear response over a 270 kPa dynamic range (24 dB maximum signal-to-noise ratio), and can resolve pressure transients up to 3910 kPa/s. Sampling at 100 kHz, the present sensor can resolve 2 kPa dynamic pressures at frequencies up to 2 kHz. Faster transients on the order of tens to hundreds of kHz can theoretically be resolved at the expense of decreasing the maximum resolvable amplitude. A methodology for designing a LCI pressure sensor for a given application is outlined based on the limitations imposed by the Nyquist criterion, the diaphragm's resonant frequency, the LCI optoelectronics, and the phase demodulation scheme. The sensor is the first to implement a low-coherence light source and a Fabry–Pérot interferometer designed to provide real-time high-fidelity pressure measurements using a metal-embedded optical fiber. The demonstrated sensor provides a platform for sensing in harsh conditions such as in nuclear and energy applications.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Analysis of pumped thermal energy storage using particle media integrated with concentrating solar power

Pumped Thermal Energy Storage (PTES) is an electricity storage system that converts electricity into thermal energy which is stored and later transformed back into electricity. Previous work has illustrated that particles have low capital costs and can be operated over a wide range of temperatures. PTES with particle storage achieves higher round-trip efficiency and specific power output than when molten salt thermal energy storage is used. This article explores hybrid systems that combine PTES with Concentrating Solar Power (CSP). Hybrid systems share the majority of components thereby reducing costs compared to two stand-alone devices. In addition, hybrid systems can provide multiple services (such as renewable power generation and electricity storage services). Using particle thermal storage in these hybrid concepts provides freedom in choosing the design conditions, since a wide range of operating temperatures is allowable, therefore making it possible to identify hybrid system designs that have good performance. In this article, two concepts for hybrid PTES-CSP are introduced. Thermodynamic models are developed and these are used to evaluate the performance of two hybrid systems. These models account for turbomachinery efficiency, and approach temperature and pressure loss in heat exchangers, as well as other sources of inefficiency, such as motor-generator losses, and air fan power. The “Solar Top-Up” Concept uses CSP to increase the temperature delivered by the charging heat pump. The discharging system uses a topping gas cycle and a bottoming steam cycle to fully exploit the available energy. Using solar heat to increase the maximum temperature from 750 K to 1100 K increases the round-trip efficiency from 41 % to 62 % and the specific work output from 88 kJ/kg to 301 kJ/kg. The second concept is a “Dual-Mode” device which provides both electricity storage and solar electricity generation with the same set of components. The PTES-mode and CSP-mode performance are optimized at different design values but careful parameter selection leads to good performance of both modes: one design produces PTES round-trip efficiency > 60 %, CSP heat engine efficiency > 40 %, and specific work outputs > 150 kJ/kg (for both cycles), when the particle receiver temperature is > 1200 K and maximum heat pump temperature is 1100 K.

14 SOLAR ENERGY↗
DOE OSTI2021

High-throughput characterization of Lu-doped zirconia

Lu-doped zirconia (LuDZ) was reported in the 1960s to be a poor oxygen ion conductor. However, we identified this system as worthy of reexamination based on the results of a machine learning-based screen for promising oxygen ion conductors, further supported by a physical argument: because Lu is the heaviest and smallest of the lanthanides, it should offer the possibility of high conductivity due to its high polarizability and size compatibility with the zirconia structure. Here the relationship between dopant concentration and conductivity in the LuDZ system was determined using a high throughput experimental methodology in which spatially resolved conductivity was measured across a compositionally graded film, spanning from Zr 0.93 Lu 0.07 O 1.965 to Zr 0.82 Lu 0.18 O 1.91 . The conductivity broadly peaks with composition at 15 cation % Lu, coinciding with the approximate phase boundary of the fully stabilized cubic phase. The composition-dependent conductivity measurements reveal a surprising increase in activation energy for ion transport with increasing Lu content with no change in this trend at the composition of the conductivity maximum. The pre-exponential factor increases sharply with Lu content, but displays a distinct plateau once the conductivity maximum composition is attained. At 500 °C, the conductivity of Zr 0.85 Lu 0.15 O 1.925 is 2 × 10 –3 S cm –1 , approaching that of optimally doped Sc-stabilized zirconia, which has the highest reported conductivity among zirconia compounds. In comparison to other oxide ion conductors, Lu-stabilized zirconia offers the advantage over ceria of negligible electronic conductivity and is easier to process than (La,Sr)(Ga,Mg)O 3-δ .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

When do hydrocarbons dewet metal surfaces? The case of coronene on Cu(111)

Here, we have used scanning tunneling microscopy and density functional theory calculations to study molecular layers of coronene on Cu(111). The structure and stability of these layers is determined by the balance between coronene-substrate and coronene-coronene interactions. Here, we characterize this balance by measuring the maximum coverage before coronene dewets the substrate to form three-dimensional islands. We find that coronene molecules lie parallel to the substrate at the maximum coverage, in contrast to previous observations of tilted coronene on metal surfaces. We attribute this previously reported tilt to a metastability caused by an activation barrier to nucleate three-dimensional islands.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Machine learning-based optimization of air-cooled heat sinks

Machine learning-based models using Artificial Neural Network (ANN) and greedy search algorithm are used to optimize air-cooled parallel plate-finned heat sinks (PPFHSs) subjected to laminar flow over an extensive range of design parameters. Here, the thermal and hydraulic performances of PPFHSs are represented by heat transfer coefficient (h) and pressure drop (ΔP), respectively. Optimization objectives for PPFHS designs can vary from industry to industry depending on their design priorities. The present study proposes a novel and generalized optimization method that defines practical optimization objectives and provides an accurate optimization process to design effective PPFHSs for a wide range of industrial applications with different design requirements. Three optimization objectives are presented in this study: (i) the largest h PΔ, (ii) the largest h within a specified maximum allowed flow rate, and (iii) the lowest weight that maximizes h for operation within the maximum allowed flow rate. While the shortcoming of the first objective is demonstrated, the other two objectives are found to be suitable for designing effective heat sinks (HSs) across different applications. Results suggest a promising trend from the third objective to develop HSs with ~ 37-68% lower weight, 80-85% reduced ΔP, and negligible penalty in h compared with optimized HSs obtained from the second objective. However, since the third objective leads to HSs with thinner fins, structural analysis should be performed to ensure reliable operation of the HSs.

42 ENGINEERING↗
DOE OSTI2025

Surface roughness and dimensional evaluation of laser powder bed fusion additively manufactured shell and tube heat exchangers

The growing interest in additively manufactured (AM) heat exchangers drove the need to understand how this construction technique impacts heat exchanger performance. Two primary factors driven by AM that influence heat exchanger performance are surface roughness and geometry. To better understand these parameters, a range of shell and tube heat exchangers constructed using laser powder bed fusion were evaluated. Of those evaluated, the surface roughness throughout a fourteen-tube, zero-baffle heat exchanger was measured using computed tomography. Between the inner and outer tubes, the inner tube surfaces had a greater surface roughness than the outer by 8.07 μm, while the surfaces at the top of the build volume had higher surface roughness values than the bottom. Dimensionally, the inner tube diameters of this heat exchanger were 0.15% different from the design value, while the outer diameters were within a 0.84 % difference. Manual measurements across seven other heat exchangers yielded a maximum 1.15% difference between the design and measured diameters. Across the build volume for all heat exchangers studied, the tube diameters at the top were larger than at the bottom by a maximum of 1.24% difference. Inconsistent melting throughout the individual parts and the build volume, as well as particle splatter and thermal gradient variation were attributed to the surface roughness and dimensional changes seen. These results strengthen the knowledge of dimensional and surface roughness considerations when designing AM heat exchangers.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Autonomous online optimization of a closed-circuit reverse osmosis system

As freshwater becomes increasingly scarce, many industrial and municipal water utilities look at premise-scale water treatment and reuse to meet water demand. Closed-circuit reverse osmosis (CCRO) has been proposed as a promising process design to do so. This sequencing batch process enables operation at higher brine salinity levels by means of a recycle flow. Optimal operation requires that the maximum salinity level at the membrane surface represents an optimal trade-off between brine disposal costs and energy efficiency. This maximum salinity level may change over time as the feed water composition changes and electricity markets fluctuate. In this article, we present the results of the experimental evaluation of an automatic technique for continuous online optimization, known as extremum seeking control. This technique has a long history in the process control community but has received little traction so far in the water industry. We modify this technique to enable its use for online optimization of CCRO, specifically to account for its sequential batch operation. We challenge the optimization schemes through several experimental tests and illustrate the advantages and drawbacks of extremum-seeking control.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Automated control and optimization of laser-driven ion acceleration

The interaction of relativistically intense lasers with opaque targets represents a highly non-linear, multi-dimensional parameter space. This limits the utility of sequential 1D scanning of experimental parameters for the optimization of secondary radiation, although to-date this has been the accepted methodology due to low data acquisition rates. High repetition-rate (HRR) lasers augmented by machine learning present a valuable opportunity for efficient source optimization. Here, an automated, HRR-compatible system produced high-fidelity parameter scans, revealing the influence of laser intensity on target pre-heating and proton generation. A closed-loop Bayesian optimization of maximum proton energy, through control of the laser wavefront and target position, produced proton beams with equivalent maximum energy to manually optimized laser pulses but using only 60% of the laser energy. This demonstration of automated optimization of laser-driven proton beams is a crucial step towards deeper physical insight and the construction of future radiation sources.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Inertial collapse of a gas bubble in a shear flow near a rigid wall

Despite the extensive research on bubble collapse near rigid walls, the bubble collapse dynamics in the presence of shear flow near a rigid wall is poorly understood. We conduct direct simulations of the Navier–Stokes equations to explore the bubble dynamics and pressures during bubble collapse near a rigid, flat wall under linear shear flow conditions. We examine the dependence of the bubble collapse morphology and wall pressures on the initial bubble location and shear rate. We find that shear distorts the bubble, generating two re-entrant jets – one developing from the side opposite to the mean flow and the other from the far end toward the wall. Upon impact of the jet on the opposite side of the bubble, water-hammer shocks are produced, which propagate outward and interact with the convoluted bubble shape. The shock stretches the bubble towards the wall, resulting in a closer impact location for the jet originating from the far end compared with the case with no shear flow. The water-hammer pressure location can be approximated as the theoretical distance travelled by a particle initialised at the bubble centre with the corresponding constant shear flow velocity. The maximum wall pressures can thus be predicted by considering the distance between the far jet impingement location and the wall along the wall-normal direction. As the shear rate is increased, the maximum wall pressure increases, although only marginally. We determine the critical initial stand-off distance from the wall at which the bubble morphology is shear dominated, i.e. characterised by converging re-entrant jets.

Bhola, Sahil (ORCID:0000000236766302)↗
DOE OSTI2024

Latest Pleistocene glacial chronology and paleoclimate reconstruction for the East River watershed, Colorado, USA

Reconstructing Pleistocene glaciation timing and extent is vital for understanding paleoclimate. Whereas late Pleistocene glaciation has been studied extensively in western North American mountain ranges, the glacial history of the western Elk Range in Colorado remains understudied, particularly in the East River watershed, a site of intense scientific focus. Here we use cosmogenic nuclide exposure and depth–profile dating methods to determine the timing of glaciation in the East River watershed. We use glacier modeling to reconstruct paleoglacier extents and quantify past climate conditions. Our findings indicate that the East River glacier retreated from its maximum position approximately 17–18 ka, moving to recessional positions between 13 and 15 ka, before experiencing more substantial retreat to high-elevation cirques around 13 ka. Glacier modeling suggests that the maximum ice extents at 17–18 ka could have been sustained by temperature depressions of approximately −6.5°C compared to modern conditions, assuming consistent precipitation. Additionally, the ice position at 13–15 ka could have been supported by temperature depressions of around −4.0°C. These results offer insights into the deglaciation timeline in the East River watershed and broader western Elk Range as well as paleoclimate conditions during the late Pleistocene, which may aid future research on critical zone evolution in the East River watershed.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Improved performance of stellarator coil design optimization

Following up on earlier work which demonstrated an improved numerical stellarator coil design optimization performance by the use of stochastic optimization (Lobsien et al., Nucl. Fusion, vol. 58 (10), 2018, 106013), it is demonstrated here that significant further improvements can be made – lower field errors and improved robustness – for a Wendelstein 7-X test case. This is done by increasing the sample size and applying fully three-dimensional perturbations, but most importantly, by changing the design sequence in which the optimization targets are applied: optimization for field error is conducted first, with coil shape penalties only added to the objective function at a later step in the design process. A robust, feasible coil configuration with a local maximum field error of 3.66 % and an average field error of 0.95 % is achieved here, as compared to a maximum local field error of 6.08 % and average field error of 1.56 % found in our earlier work. These new results are compared to those found without stochastic optimization using the FOCUS and ONSET suites. The relationship between local minima in the optimization space and coil shape penalties is also discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Constrained stellarator coil curvature optimization with FOCUS

Finding less complicated coils that have adequately low field errors is a crucial step in stellarator development. One coil metric that is of high importance is the maximum curvature of the coil centreline, or coil single filament. Conductors cannot be bent below some threshold minimum radius of curvature. High coil curvatures can cause strains to exceed acceptable levels, especially in superconducting coils. We investigate three ways to optimize coil curvature and find that applying penalty functions to the coil curvature solves for coils that have a constrained maximum curvature and low field error. Penalty functions are implemented in FOCUS and coil solutions optimized for an HSX-like ‘plasma boundary’ are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

The effect of shear flow on the resistive tearing instability

We develop a new scaling theory for the resistive tearing mode instability of a current sheet with a strong shear flow across the layer. The growth rate decreases with increasing flow shear and is completely stabilized as the shear flow becomes Alfvénic: both in the constant-Ψ regime, as in previous results, but we also show that the growth rate is in fact suppressed more strongly in the nonconstant-Ψ regime. As a consequence, for sufficiently large flow shear, the maximum of the growth rate is always affected by the shear suppression, and the wavenumber at which this maximum growth rate is attained is an increasing function of the strength of the flow shear. These results may be important for the onset of reconnection in imbalanced MHD turbulence.

astrophysical plasmas↗
DOE OSTI2020

First-Principles Modeling of Sodium Ion and Water Intercalation into Titanium Disulfide Interlayers for Water Desalination

Recent experiments revealed the possibility of using titanium disulfide (TiS 2 ) as the cathode material in capacitive deionization (CDI) devices for water desalination. Although it performed stably up to 70 cycles with a salt removal capacity of 14 mg/g (corresponding to a sodium ion removal capacity of 35.8 mg/g) at high molar concentration (600 mM NaCl), the maximum capacity of TiS 2 as a CDI electrode was much lower (~70 mAh/g) than as a supercapacitor (239 mAh/g). Understanding why the ion capacities of these two configurations of the same material differ will entail elucidating detailed charge/discharge mechanisms at the atomic scale. Here, we present density functional theory simulations of sodium intercalation into TiS 2 interlayers in order to gain such understanding. We systematically investigated TiS 2 stacking patterns and ion intercalation sites, energetics of the intercalated compounds, and phase transformation during sodium intercalation. The calculated structural evolution and capacitance–voltage curve agree quite well with previous measurements. We conclude that the different maximum capacities of TiS 2 measured in aqueous and dry environments originate from weaker interlayer interactions with respect to shear strain after ~33% intercalation of Na + –H 2 O pairs, which is detrimental to the mechanical stability of TiS 2 . In conclusion, this study sheds light on the underlying mechanisms of ion intercalation into layered materials and contributes to understanding requirements for future design and optimization of CDI electrode materials for water desalination.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Reducing Surface Recombination Velocity of Methylammonium-Free Mixed-Cation Mixed-Halide Perovskites via Surface Passivation

We control surface recombination in the mixed-cation, mixed-halide perovskite, FA0.83Cs0.17Pb(I0.85Br0.15)3, by passivating nonradiative defects with the polymerizable Lewis base (3-aminopropyl)trimethoxysilane (APTMS). We demonstrate average minority carrier lifetimes >4 µs, nearly single exponential monomolecular photoluminescence decays, and high external photoluminescence quantum efficiencies (>20%, corresponding to ~97% of the maximum theoretical quasi-Fermi-level splitting) at low excitation fluence. We confirm both the composition and valence band edge position of the FA0.83Cs0.17Pb(I0.85Br0.15)3 perovskite using multi-institutional, cross-validated, X-ray photoelectron spectroscopy and UV photoelectron spectroscopy measurements. We extend the APTMS surface passivation to higher bandgap double-cation (FA and Cs) compositions (1.7, 1.75, and 1.8 eV) as well as the widely used triple-cation (FA, MA, and Cs) composition. Finally, we demonstrate that the average surface recombination velocity decreases from ~1000 to ~10 cm/s post APTMS passivation for FA0.83Cs0.17Pb(I0.85Br0.15)3. Our results demonstrate that surface-mediated recombination is the primary nonradiative loss pathway in many methylammonium (MA)-free mixed-cation mixed-halide films with a range of different bandgaps, which is a problem observed for a wide range of perovskite active layers and reactive electrical contacts. Our study also provides insights to develop passivating molecules that help reduce surface recombination in MA-free mixed-cation mixed-halide films and indicates that surface passivation and contact engineering will enable near-theoretical device efficiencies with these materials.

14 SOLAR ENERGY↗
DOE OSTI2020

From Waste-Heat Recovery to Refrigeration: Compositional Tuning of Magnetocaloric Mn 1+ x Sb

Magnetic refrigeration, as well as waste-heat recovery, can be accomplished through the magnetocaloric effect, where temperature changes the magnetic state of a material or vice versa. Promising magnetocaloric materials display large changes in magnetic entropy (ΔS M ) upon application of a moderate magnetic field and are often associated with magnetic materials possessing some degree of magnetostructural coupling. In such compounds, the magnetic transition is coupled to some structural transition at the ordering temperature, and indicators for these are readily calculated by the magnetic deformation proxy Σ M . MnSb, with a Curie temperature T C = 577 K, has a calculated magnetic deformation of Σ M = 5.9% and is a promising candidate material for waste-heat recovery. The temperature dependence of structural, magnetic, and magnetocaloric properties of Mn 1+ x Sb, where $x$ is a tunable amount of interstitial Mn, is studied here. specifically, excess Mn is incorporated as an interstitial whose magnetic moment is antialigned with the stoichiometric Mn, and the excess Mn has the effect of lowering T C , such that the Curie temperature can be tuned from 577 K to nearly room temperature at 318 K for $x$ = 0.2. For $x$ = 0.0, 0.1, and 0.2, values of ΔS M under a maximum magnetic field $H$ = 5 T are found to be 3.65, 3.00, and 2.83 J K -1 kg -1 , respectively. While the maximum ΔS M decreases with $x$, the high refrigerant capacity a more holistic measure of performance-is retained in this highly tunable system.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Numerical Simulations in Support of a Long-Term Test of Gas Production from Hydrate Accumulations on the Alaska North Slope: Reservoir Response to Interruptions of Production (Shut-Ins)

In this work, we investigate by means of numerical simulation a planned year-long field test of depressurization-induced production from a permafrost-associated hydrate reservoir on the Alaska North Slope at the site of the recently drilled Hydrate-01 Stratigraphic Test Well. The main objective of this study is to assess quantitatively the impact of temporary interruptions (well shut-ins) on the expected fluid production performance from the B1 Sand of the stratigraphic Unit B during controlled depressurization over different time scales, as well as on other relevant aspects of the system response that have the potential to significantly affect the design of the field test. We consider eight different cases of depressurization, including (a) rapid depressurization over a 60-day period to a terminal bottomhole pressure P W of 2.8 MPa and (b) a slower depressurization rate to a final P W of 0.6 MPa at the end of the year-long production test, in addition to (c) a multi-step depressurization regime and (d) a quasi-linear continuous depressurization strategy. The results of the study indicate that shut-ins obviously reduce gas release and production during and immediately after their occurrence, but their longer-term effects are strongly dependent on the depressurization regime and on the time of observation, covering the entire range of potential outcomes. Shut-ins (a) have a universally strong negative effect when quasi-linear depressurization is involved regardless of the length of the production period, and (b) have a strong positive effect in multi-step depressurization schemes that becomes apparent earlier for large initial pressure drops, but (c) can also appear to have practically no effect for slow stepwise depressurization at the end of the year-long production test. Shut-ins lead to a rapid reformation of hydrates, even to the point of disappearance of a free gas phase in the reservoir. Rapid depressurization regimes lead to early maximum rates of hydrate dissociation and gas production, while the maximum rates occur at the end of the production test for the cases of slower depressurization. Shut-ins do not appear to have a significant impact on water production, as the cessation of production is followed by higher rates production when depressurization resumes. Similarly, (a) the fraction of produced CH 4 originating from exsolution from the water, (b) the water-to-gas ratio, and (c) the rate of replenishment of produced water by boundary inflows do not appear significantly affected by shut-ins, the effects of which seem to be temporary in the majority of the cases. The study confirmed the superiority of multi-step depressurization methods as the most effective strategies for hydrate dissociation and gas production and showed that two observation wells (located at distances of 30 and 50 m from the production well) are appropriately positioned and both able to capture the P, T, and S G behavior during the fluid production and shut-ins in any of the eight cases we investigated.

03 NATURAL GAS↗