Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hinges”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Reflection-plane tests of spoilers on an advanced technology wing with a large Fowler flap

Wind tunnel experiments were conducted to determine the effectiveness of spoilers applied to a finite-span wing which utilizes the GA(W)-1 airfoil section and a 30% chord full-span Fowler flap. A series of spoiler cross sectioned shapes were tested utilizing a reflection-plane model. Five-component force characteristics and hinge moment measurements were obtained. Results confirm earlier two-dimensional tests which showed that spoilers could provide large lift increments at any flap setting, and that spoiler control reversal tendencies could be eliminated by providing a vent path from lower surface to upper surface. Performance penalties due to spoiler leakage airflow were measured.

Wentz, W. H., Jr.↗
NASA NTRS1976

Terminal area energy management regime investigations utilizing an 0.030-scale model (47-0) of the space shuttle vehicle orbiter configuration 140A/B/C/R in the Ames Research Center 11 x 11 foot transonic wind tunnel (0A148), volume 1

Data obtained in wind tunnel tests are presented. The objectives of the tests were to: (1) obtain pressure distributions, forces and moments over the vehicle 5 Orbiter in the terminal area energy management (TAEM) and approach phases of flight; (2) obtain elevon and rudder hinge moments in the TAEM and approach phases of flight; (3) obtain body flap and elevon loads for verification of loads balancing with integrated pressure distributions; and (4) obtain pressure distributions near the short OMS pods in the high subsonic, transonic and low supersonic Mach number regimes. Testing was conducted over a Mach number range from 0.6 to 1.4 with Reynolds number variations from 4.57 million to 2.74 million per foot. Model angle-of-attack was varied from -4 to 16 degrees and angles of side slip ranged from -8 to 8 degrees.

Hawthorne, P. J.↗
NASA NTRS1976

Terminal area energy management regime investigations utilizing an 0.030-scale model (47-0) of the space shuttle vehicle orbiter configuration 140A/B/C/R in the Ames Research Center 11 x 11 foot transonic wind tunnel (OA148), volume 5

Data obtained in wind tunnel test OA148 are presented. The objectives of the test series were to: (1) obtain pressure distributions, forces and moments over the vehicle 5 orbiter in the thermal area energy management (TAEM) and approach phases of flight; (2) obtain elevon and rudder hinge moments in the TAEM and approach phases of flight; (3) obtain body flap and elevon loads for verification of loads balancing with integrated pressure distributions; and (4) obtain pressure distributions near the short OMS pods in the high subsonic, transonic and low supersonic Mach number regimes.

Hawthorne, P. J.↗
NASA NTRS1976

A computer program to calculate the longitudinal aerodynamic characteristics of wing-flap configurations with externally blown flaps

A vortex lattice lifting-surface method is used to model the wing and multiple flaps. Each lifting surface may be of arbitrary planform having camber and twist, and the multiple-slotted trailing-edge flap system may consist of up to ten flaps with different spans and deflection angles. The engine wakes model consists of a series of closely spaced vortex rings with circular or elliptic cross sections. The rings are normal to a wake centerline which is free to move vertically and laterally to accommodate the local flow field beneath the wing and flaps. The two potential flow models are used in an iterative fashion to calculate the wing-flap loading distribution including the influence of the waves from up to two turbofan engines on the semispan. The method is limited to the condition where the flow and geometry of the configurations are symmetric about the vertical plane containing the wing root chord. The calculation procedure starts with arbitrarily positioned wake centerlines and the iterative calculation continues until the total configuration loading converges within a prescribed tolerance. Program results include total configuration forces and moments, individual lifting-surface load distributions, including pressure distributions, individual flap hinge moments, and flow field calculation at arbitrary field points.

Mendenhall, M. R.↗
NASA NTRS1976

Terminal area energy management regime investigations utilizing an 0.030-scale model (47-0) of the space shuttle vehicle orbiter configuration 140A/B/C/R in the Ames Research Center 11 x 11 foot transonic wind tunnel (OH/48)

Data obtained in a wind tunnel test were examined to: (1) obtain pressure distributions, forces and moments over the vehicle 5 Orbiter in the terminal area energy management (TAEM) and approach phases of flight; (2) obtain elevon and rudder hinge moments in the TAEM and approach phases of flight; (3) obtain body flap and elevon loads for verification of loads balancing with integrated pressure distributions; and (4) obtain pressure distributions near the short OMS pods in the high subsonic, transonic and low supersonic Mach number regimes. Testing was conducted over a Mach number range from 0.6 to 1.4 with Reynolds number variations from 7.57 x 1 million to 2.74 x 1 million per foot. Model angle of attack was varied from -4 to 16 degrees and angles of sideslip ranged from -8 to 8 degrees.

Hawthorne, P. J.↗
NASA NTRS1976

Investigations of the 0.020-scale 88-OTS Integrated Space Shuttle Vehicle Jet-Plume Model in the NASA/Ames Research Center 11 by11-Foot Unitary Plan Wind Tunnel (IA80)

The results are documented of jet plume effects wind tunnel test of the 0.020-scale 88-OTS launch configuration space shuttle vehicle model in the 11 x 11 foot leg of the NASA/Ames Research Center Unitary Plan Wind Tunnel. This test involved cold gas main propulsion system (MPS) and solid rocket motor (SRB) plume simulations at Mach numbers from 0.6 to 1.4. Integrated vehicle surface pressure distributions, elevon and rudder hinge moments, and wing and vertical tail root bending and torsional moments due to MPS and SRB plume interactions were determined. Nozzle power conditions were controlled per pretest nozzle calibrations. Model angle of attack was varied from -4 deg to +4 deg; model angle of sideslip was varied from -4 deg to +4 deg. Reynolds number was varied for certain test conditions and configurations, with the nominal freestream total pressure being 14.69 psia. Plotted force and pressure data are presented.

Nichols, M. E.↗
NASA NTRS1976

An investigation of flap-lag stability of wind turbine rotors in the presence of velocity gradients and helicopter rotors in forward flight

The flap-lag equations of motion of a torsionally rigid and centrally hinged spring-restrained rigid blade are developed using quasi-steady blade-element aerodynamic theory. These equations have periodic coefficients and are applicable to both wind-turbine rotors with velocity gradients and helicopter rotors in forward flight. By solving these equations both by the Floquet-Liapunov method and by an approximate method, the range of applicability of the latter method is established. Flap-lag and pure flapping stability boundaries illustrating the effects of flow and rotor parameters are presented. Finally, some discussion on the techniques for generating the Floquet transition matrix and on the relative merits of the coordinate axes system is presented.

Kaza, K. R. V.↗
NASA NTRS1976

Aeroelastic stability and control of an oblique wing

Dynamic model tests were staged to compare the aeroelastic stability of a free-flying oblique-winged aircraft and the known divergent instability characterizing swept-forward wing configurations, to test the effect of wing elasticity on aileron control and trim. The aircraft fuselage was clamped in some tests and left free to roll in others. Two rigid wing panels were hinged near the wing center with elastic restraining springs. It is found that the aeroelastic divergence affecting swept-forward wings does not occur with an oblique wing, whose aeroelastic instability sets in at a dynamic pressure exceeding that for static divergence of swept-forward wings, and appears in the form of undamped oscillations. Oblique wing stability is sensitive to the moment of inertia of the fuselage in roll. Roll control and lateral trim are attainable with conventional ailerons, even at speeds at which divergence of a clamped forward wing shows up.

Jones, R. T.↗
NASA NTRS1977

Protection against explosive blasts

Simple, hinged cover plate is effective against high explosive blasts. Blast energy under cover is transformed into kinetic energy of plate.

Bement, L. J.↗
NASA NTRS1976

A model study of landing mat subjected to C-5A loadings

The 1.22 x 1.37 m mat runway in the standard brick pattern with transverse hinged joints is more stable and less susceptible to a buckling failure than the 0.60 x 2.74 m mat runway. Use of tension anchors appears to be a feasible means of controlling longitudinal displacement of the runway and potential runway buckling. Anchors appear to be a practical means to reduce maintenance on mat runways. The 1.22 x 1.37 m mat in the alternate brick pattern or the 90 deg rotated standard brick pattern forms a dynamically more stable runway with a high resistance to buckling failure. The runway in these patterns is much stiffer and longitudinal movement was less than for the standard brick pattern. The model 1.22 x 1.37 m alternate brick pattern runway was difficult to assemble and extremely difficult to take apart.

Blotter, P. T.↗
NASA NTRS1976

Results of investigations conducted in the LaRC 8-foot transonic pressure tunnel using the 0.010-scale 72-OTS model of the space shuttle integrated vehicle (IA93)

Test procedures, history, and data from the wind tunnel test are presented. Aero-loads were investigated on the updated configuration-5 space shuttle launch vehicle at Mach numbers from 0.600 to 1.205. Six-component vehicle forces and moments, base and sting-cavity pressures, elevon hinge moments, wing-root bending and torsion moments, and normal shear force data were obtained. Full simulation of updated vehicle protuberances and attach hardware was employed. Various elevon deflection angles were tested with two different forward orbiter-to-external-tank attach-strut configurations. The entire model was supported by means of a balance mounted in the orbiter through its base and suspended from a sting.

Nichols, M. E.↗
NASA NTRS1976

Results of investigations conducted in the LaRC 8-foot transonic pressure tunnel using the 0.010-scale 72-OTS model of the space shuttle integrated vehicle (IA93), volume 2

Test procedures, history, and plotted coefficient data are presented for an aero-loads investigation on the updated configuration-5 space shuttle launch vehicle at Mach numbers from 0.600 to 1.205. Six-component vehicle forces and moments, base and sting-cavity pressures, elevon hinge moments, wing-root bending and torsion moments, and normal shear force data were obtained. Full simulation of updated vehicle protuberances and attach hardware was employed.

Nichols, M. E.↗
NASA NTRS1976

Results of investigations conducted in the LaRC 4-foot unitary plan wind tunnel leg no. 1 using the 0.010-scale 72-OTS model of the space shuttle integrated vehicle (IA94A)

Aero-loads investigations were conducted on the updated configuration-5 space shuttle launch vehicle at Mach numbers 2.50, 3.50, and 4.50. Six-component vehicle forces and moments, base and sting-cavity pressures, elevon hinge moments, wing-root bending and torsion moments, and normal shear force data were obtained. Full simulation of updated vehicle protuberances and attach hardware was employed. Various elevon deflection angles were tested, with two different forward orbiter-to-external-tank attach-strut configurations. The entire vehicle model 72-OTS was supported by means of a balance mounted in the orbiter through its base and suspended from an appropriate sting for the specific tunnel.

Nichols, M. E.↗
NASA NTRS1977

Load and stability measurements on a soft-inplane rotor system incorporating elastomeric lead-lag dampers

An experimental investigation was conducted of the dynamic response and inplane stability associated with a new soft-inplane helicopter rotor. The unique feature of this rotor was the use of an internal elastomeric damper to restrain the blade inplane motion about the lead-lag hinge. The properties of the elastomer were selected to provide both a nominal first inplane frequency ratio of 0.65 and sufficient damping to eliminate the need for additional external damping sources to prevent ground resonance on a typical fuselage structure. For this investigation a 1/5-scale aeroelastic model was used to represent the rotor. The four-blade model had a diameter of 3.05 m (10 ft) and a solidity of 0.103. The first out-of-plane frequency ratio was 1.06. The model was tested in hover and in forward flight up to an advance ratio of 0.45. At each forward speed the rotor lift was varied up to simulated maneuver conditions. The measured rotor loads and response were within acceptable limits, and no adverse response qualities were observed. Moderate out-of-plane hub moments were measured, even for zero lift, to indicate the beneficial control power available for this design. Blade inplane stability testing indicated that the rotor system damping remained at moderate levels throughout the operating envelope.

Weller, W. H.↗
NASA NTRS1976

Lateral stability and control tests of the XP-77 airplane in the NACA full-scale tunnel, 16 June 1944

Tests were made in the NACA full-scale tunnel to determine the lateral stability and control characteristics of the XP-77 airplane. Measurements were made of the forces and moments on the airplane at various angles of attack and angles of yaw. The measurements were made with the propeller removed and with the propeller installed and operating at various thrust coefficients, and with the landing flaps retracted and deflected. The effects of aileron, elevator, and rudder deflection on control surface effectiveness and hinge moments were determined. The tests were planned to obtain the data required to evaluate as completely as possible the Army Air Force requirements on lateral stability and control for pursuit-type airplanes.

Czarnecki, K. R.↗
NASA NTRS1977

Aerodynamic characteristics of an F-8 aircraft configuration with a variable camber wing at Mach numbers from 1.5 to 2.0

A 0.1-scale model of an F-8 aircraft was tested over a range of Mach numbers from 1.5 to 2.0. Reynolds number of 4.12 million was based on wing mean-aerodynamic chord for angles of attack varying from -2 deg to +12 deg. The model was equipped with an advanced-technology-conformal-variable-camber wing (ATCVCW) having simple hinge flaps. Data were also obtained for the model equipped with the basic F-8 wing and conventional flaps. Model variables included aileron and wing trailing edge deflections and horizontal tail incidence. The ATCVCW configuration produced slight improvements in lift-curve slope, drag, and static longitudinal stability over that of the basic F-8 wing configuration. Flap effectiveness was essentially the same for both wings.

Boltz, F. W.↗
NASA NTRS1978

Dynamic wind-tunnel tests of an aeromechanical gust-alleviation system using several different combinations of control surfaces

Some experimental results are presented from wind tunnel studies of a dynamic model equipped with an aeromechanical gust alleviation system for reducing the normal acceleration response of light airplanes. The gust alleviation system consists of two auxiliary aerodynamic surfaces that deflect the wing flaps through mechanical linkages when a gust is encountered to maintain nearly constant airplane lift. The gust alleviation system was implemented on a 1/6-scale, rod mounted, free flying model that is geometrically and dynamically representative of small, four place, high wing, single engine, light airplanes. The effects of flaps with different spans, two size of auxiliary aerodynamic surfaces, plain and double hinged flaps, and a flap elevator interconnection were studied. The model test results are presented in terms of predicted root mean square response of the full scale airplane to atmospheric turbulence. The results show that the gust alleviation system reduces the root mean square normal acceleration response by 30 percent in comparison with the response in the flaps locked condition. Small reductions in pitch-rate response were also obtained. It is believed that substantially larger reductions in normal acceleration can be achieved by reducing the rather high levels of mechanical friction which were extant in the alleviation system of the present model.

Stewart, E. C.↗
NASA NTRS1978

Applications of the hybrid coordinate method to the TOPS autopilot

Preliminary results are presented from the application of the hybrid coordinate method to modeling TOPS (thermoelectric outer planet spacecraft) structural dynamics. Computer simulated responses of the vehicle are included which illustrate the interaction of relatively flexible appendages with an autopilot control system. Comparisons were made between simplified single-axis models of the control loop, with spacecraft flexibility represented by hinged rigid bodies, and a very detailed three-axis spacecraft model whose flexible portions are described by modal coordinates. While single-axis system, root loci provided reasonable qualitative indications of stability margins in this case, they were quantitatively optimistic when matched against responses of the detailed model.

Fleischer, G. E.↗