Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fiber surfaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Zirconium fluoride glass - Surface crystals formed by reaction with water

The hydrated surfaces of a zirconium barium fluoride glass, which has potential for application in optical fibers and other optical elements, were observed by scanning electron microscopy. Crystalline zirconium fluoride was identified by analysis of X-ray diffraction patterns of the surface crystals and found to be the main constituent of the surface material. It was also found that hydrated zirconium fluorides form only in highly acidic fluoride solutions. It is possible that the zirconium fluoride crystals form directly on the glass surface as a result of its depletion of other ions. The solubility of zirconium fluoride is suggested to be probably much lower than that of barium fluoride (0.16 g/100 cu cm at 18 C). Dissolution was determined to be the predominant process in the initial stages of the reaction of the glass with water. Penetration of water into the glass has little effect.

Doremus, R. H.↗
NASA NTRS1988

Graphite/Epoxy Deicing Heater

Heat applied close to surface protected. One ply of highly electrically- and thermally-conductive brominated-graphite fiber composite laminated between two plies of electrically-insulating composite material, with michel foil making contact with end portions of graphite fibers. Part of foil exposed beyond composite to serve as electrical contact. Graphite/Epoxy composite heater developed to prevent and reverse formation of ice on advanced composite surfaces of aircraft.

Hung, Ching-Cheh↗
NASA NTRSDate not supplied

Investigation of the effect of etch pits on the material properties of carbon fiber structures

It is well known that etch pits are formed on carbon surfaces during their consumption in reactive gas environments such as during ablation of carbon-based thermal protection system (TPS) materials. These pits start out from atomic defects on the carbon surface, grow in size and then ultimately lead to the complete removal of the solid carbon material [1, 2]. However, the effect of such etch pits on the material properties of carbon ablators such as FiberForm are poorly understood, as the maximum size of pits are on the order of microns in size, which makes them hard to observe experimentally. Hence, we have developed a module within the Porous Microstructure Analysis code PuMA [3] that can generate etch pits on an arbitrary material surface, with a prescribed distribution of pit size and density. Figure 1 shows a FiberForm sample with artificially generated pits of varying radii and pit density. We use this newly developed module to calculate material properties of FiberForm, which is the base material for one of the most commonly used TPS materials - Phenolic Impregnated Carbon Ablator (PICA). The detailed microstructure of FiberForm in PuMA will either be generated synthetically or obtained from X-ray microtomography [4]. Our simulations show that material properties such as the thermal conductivity and tortuosity decrease with increasing degree of pitting. This will be helpful to more accurately predict the degradation of carbon-based TPS during ablation, and furthermore may allow us to identify previously unknown TPS failure modes due to pitting.

PuMA↗
NASA NTRSDate not supplied

Investigation of the Effect of Etch Pits on the Material Properties of Carbon Fiber Structures

It is well known that etch pits are formed on carbon surfaces during their consumption in reactive gas environments such as during ablation of carbon-based thermal protection system (TPS) materials. These pits start out from atomic defects on the carbon surface, grow in size and then ultimately lead to the complete removal of the solid carbon material. However, the effect of such etch pits on the material properties of carbon ablators such as FiberForm are poorly understood, as the maximum size of pits are on the order of microns in size, which makes them hard to observe experimentally. Hence, we have developed a module within the Porous Microstructure Analysis code PuMA that can generate etch pits on an arbitrary material surface, with a prescribed distribution of pit size and density. We use this newly developed module to calculate material properties of FiberForm, which is the base material for one of the most commonly used TPS materials - Phenolic Impregnated Carbon Ablator (PICA). The detailed microstructure of FiberForm in PuMA will either be generated synthetically or obtained from X-ray microtomography. Our simulations show that material properties such as the thermal conductivity and tortuosity decrease with increasing degree of pitting. This will be helpful to more accurately predict the degradation of carbon-based TPS during ablation, and furthermore may allow us to identify previously unknown TPS failure modes due to pitting.

PuMA↗
NASA NTRS1974

Investigation of fatigue strength of multilayer advanced fiber composites

The analytical characterization of a multilayer fiber composite plate (without hole) was accomplished for both static and dynamic loading conditions using the finite difference technique. Thornel 300/5208 composites with and without holes were subjected to static and tensile fatigue testing. Five (5) fiber orientations were submitted to test. Tensile fatigue testing also included three (3) loading conditions and two (2) frequencies. The low-cycle test specimens demonstrated a shorter tensile fatigue life than the high-cycle test specimens. Failure surfaces demonstrated effect of testing conditions. Secondary failure mechanisms, such as: delamination, fiber breakage, and edge fiber delamination were present. Longitudinal delamination between plies also occurred in these specimens.

Thornton, H. R.↗
NASA NTRS2015

Structural Characterization of Advanced Composite Tow-Steered Shells with Large Cutouts

The structural performance of two advanced composite tow-steered shells with large cutouts, manufactured using an automated fiber placement system, is assessed using both experimental and analytical methods. The fiber orientation angles of the shells vary continuously around their circumference from +/- 10 degrees on the crown and keel, to +/- 45 degrees on the sides. The raised surface features on one shell result from application of all 24 tows during each fiber placement system pass, while the second shell uses the tow drop/add capability of the system to achieve a more uniform wall thickness. These unstiffened shells, both without and with small cutouts, were previously tested in axial compression and buckled elastically. In this study, a single unreinforced cutout, scaled to represent a cargo door on a commercial aircraft, is machined into one side of each shell. The prebuckling axial stiffnesses and bifurcation buckling loads of these shells with large cutouts are also computed using linear finite element structural analyses for preliminary comparisons with test data. During testing, large displacements are observed around the large cutouts, but the shells maintain an average of 91 percent of the axial stiffness, and also carry 85 percent of the buckling loads, when compared to the pristine shells without cutouts. These relatively small reductions indicate that there is great potential for using tow steering to mitigate the adverse effects of large cutouts on the overall structural performance.

Wu, K. Chauncey↗
NASA NTRS1978

Dual membrane hollow fiber fuel cell and method of operating same

A gaseous fuel cell is described which includes a pair of electrodes formed by open-ended, ion-exchange hollow fibers, each having a layer of metal catalyst deposited on the inner surface and large surface area current collectors such as braided metal mesh in contact with the metal catalyst layer. A fuel cell results when the electrodes are immersed in electrolytes and electrically connected. As hydrogen and oxygen flow through the bore of the fibers, oxidation and reduction reactions develop an electrical potential. Since the hollow fiber configuration provides large electrode area per unit volume and intimate contact between fuel and oxidizer at the interface, and due to the low internal resistance of the electrolyte, high power densities can be obtained.

Ingham, J. D.↗
NASA NTRS1992

Transient response of a laminated composite plate

Results are presented from an investigation of the effect of layering on transient wave propagation in a laminated cross-ply plate, giving attention to the case of 2D plane strain in the case where a line vertical force is applied on a free surface of the plate; the line may be either parallel or perpendicular to the fibers in a ply. The results are in both the time and frequency domains for the normal stress component in the x direction, at a point on the surface of the plate on which the force is applied. Comparative results are also presented for a homogeneous plate whose properties are the static effective ones, when the number of plies is large.

Datta, S. K.↗
NASA NTRS2002

Investigation of Structural Properties of Carbon-Epoxy Composites Using Fiber-Bragg Gratings

Fiber Bragg-gratings are embedded in carbon-epoxy laminates as well as bonded on the surface of cylindrical structures fabricated out of such composites. Structural properties of such composites is investigated. The measurements include stress-strain relation in laminates and Poisson's ratio in several specimens with varying orientation of the optical fiber Bragg-sensor with respect to the carbon fiber in an epoxy matrix. Additionally, Bragg gratings are bonded on the surface of cylinders fabricated out of carbon-epoxy composites and longitudinal and hoop strain on the surface is measured.

Grant, J.↗
NASA NTRS2004

Module for Oxygenating Water without Generating Bubbles

A module that dissolves oxygen in water at concentrations approaching saturation, without generating bubbles of oxygen gas, has been developed as a prototype of improved oxygenators for water-disinfection and water-purification systems that utilize photocatalyzed redox reactions. Depending on the specific nature of a water-treatment system, it is desirable to prevent the formation of bubbles for one or more reasons: (1) Bubbles can remove some organic contaminants from the liquid phase to the gas phase, thereby introducing a gas-treatment problem that complicates the overall water-treatment problem; and/or (2) in some systems (e.g., those that must function in microgravity or in any orientation in normal Earth gravity), bubbles can interfere with the flow of the liquid phase. The present oxygenation module (see Figure 1) is a modified version of a commercial module that contains >100 hollow polypropylene fibers with a nominal pore size of 0.05 m and a total surface area of 0.5 m2. The module was originally designed for oxygenation in a bioreactor, with no water flowing around or inside the tubes. The modification, made to enable the use of the module to oxygenate flowing water, consisted mainly in the encapsulation of the fibers in a tube of Tygon polyvinyl chloride (PVC) with an inside diameter of 1 in. (approx.=25 mm). In operation, water is pumped along the insides of the hollow fibers and oxygen gas is supplied to the space outside the hollow tubes inside the PVC tube. In tests, the pressure drops of water and oxygen in the module were found to be close to zero at water-flow rates ranging up to 320 mL/min and oxygen-flow rates up to 27 mL/min. Under all test conditions, no bubbles were observed at the water outlet. In some tests, flow rates were chosen to obtain dissolved-oxygen concentrations between 25 and 31 parts per million (ppm) . approaching the saturation level of approx.=35 ppm at a temperature of 20 C and pressure of 1 atm (approx.=0.1 MPa). As one would expect, it was observed that the time needed to bring a flow of water from an initial low dissolved-oxygen concentration (e.g., 5 ppm) to a steady high dissolved-oxygen concentration at or near the saturation level depends on the rates of flow of both oxygen and water, among other things. Figure 2 shows the results of an experiment in which a greater flow of oxygen was used during the first few tens of minutes to bring the concentration up to approx.=25 ppm, then a lesser flow was used to maintain the concentration.

Gonzalez-Martin, Anuncia↗
NASA NTRS1993

An overview of elevated temperature damage mechanisms and fatigue behavior of a unidirectional SCS-6/Ti-15-3 composite

The fatigue behavior of a unidirectionally reinforced titanium matrix composite (TMC), SiC/Ti-15-3, was thoroughly characterized to support life prediction modeling of advanced TMC disks designed for gas turbine engine applications. The results of this coupon-level experimental investigation are reviewed. On a stress basis, the isothermal fatigue behavior of the (0 deg) TMC revealed significant improvements over the unreinforced matrix. In contrast, the (90 deg) TMC exhibited degraded properties and lives for similar comparisons. This was attributed to the weak fiber/matrix interfacial bond. Encasing the (0 deg) TMC with a Ti-15-3 case did not affect isothermal fatigue lives at higher strain levels. However, at lower strain levels, rapid initiation and propagation of large fatigue cracks in the case degraded the fatigue lives. Thermomechanical fatigue (TMF) lives were significantly reduced for the (0 deg) TMC when compared to isothermal lives. At high strains, in-phase TMF produced extremely short lives. This degradation was attributed to fiber overload failures brought about by stress relaxation in the matrix. At low strains, out-of-phase TMF conditions became life limiting. Environment-assisted surface cracking was found to accelerate fatigue failure. This produced extensive matrix damage with minimal fiber damage. For the (90 deg) TMC, TMF conditions did not promote an additional degradation in cyclic life beyond that observed under isothermal conditions.

Castelli, Michael G.↗
NASA NTRS1988

Fatigue testing and damage development in continuous fiber reinforced metal matrix composites

A general overview of the fatigue behavior of metal matrix composites (MMC) is presented. The first objective is to present experimental procedures and techniques for conducting a meaningful fatigue test to detect and quantify fatigue damage in MMC. These techniques include interpretation of stress-strain responses, acid etching of the matrix, edge replicas of the specimen under load, radiography, and micrographs of the failure surfaces. In addition, the paper will show how stiffness loss in continuous fiber reinforced metal matrix composites can be a useful parameter for detecting fatigue damage initiation and accumulation. Second, numerous examples of how fatigue damage can initiate and grow in various MMC are given. Depending on the relative fatigue behavior of the fiber and matrix, and the interface properties, the failure modes of MMC can be grouped into four categories: (1) matrix dominated, (2) fiber dominated, (3) self-similar damage growth, and (4) fiber/matrix interfacial failures. These four types of damage will be discussed and illustrated by examples with the emphasis on the fatigue of unnotched laminates.

Johnson, W. S.↗
NASA NTRS1989

Fatigue testing and damage development in continuous fiber reinforced metal matrix composites

A general overview of the fatigue behavior of metal matrix composites (MMC) is presented. The first objective is to present experimental procedures and techniques for conducting a meaningful fatigue test to detect and quantify fatigue damage in MMC. These techniques include interpretation of stress-strain responses, acid etching of the matrix, edge replicas of the specimen under load, radiography, and micrographs of the failure surfaces. In addition, the paper will show how stiffness loss in continuous fiber reinforced metal matrix composites can be a useful parameter for detecting fatigue damage initiation and accumulation. Second, numerous examples of how fatigue damage can initiate and grow in various MMC are given. Depending on the relative fatigue behavior of the fiber and matrix, and the interface properties, the failure modes of MMC can be grouped into four categories: (1) matrix dominated, (2) fiber dominated, (3) self-similar damage growth, and (4) fiber/matrix interfacial failures. These four types of damage will be discussed and illustrated by examples with the emphasis on the fatigue of unnotched laminates.

Johnson, W. S.↗
NASA NTRS2004

Improved BN Coatings on SiC Fibers in SiC Matrices

Modifications of BN-based coatings that are used as interfacial layers between the fibers and matrices of SiCfiber/SiC-matrix composite materials have been investigated to improve the thermomechanical properties of these materials. Such interfacial coating layers, which are also known as interphases (not to be confused with interphase in the biological sense), contribute to strength and fracture toughness of a fiber/matrix composite material by providing for limited amounts of fiber/matrix debonding and sliding to absorb some of the energy that would otherwise contribute to the propagation of cracks. Heretofore, the debonding and sliding have been of a type called inside debonding because they have taken place predominantly on the inside surfaces of the BN layers that is, at the interfaces between the SiC fibers and the interphases. The modifications cause the debonding and sliding to include more of a type, called outside debonding, that takes place at the outside surfaces of the BN layers that is, at the interfaces between the interphases and the matrix (see figure). One of the expected advantages of outside debonding is that unlike in inside debonding, the interphases would remain on the crack-bridging fibers. The interphases thus remaining should afford additional protection against oxidation at high temperature and should delay undesired fiber/fiber fusion and embrittlement of the composite material. A secondary benefit of outside debonding is that the interphase/matrix interfaces could be made more compliant than are the fiber/interphase interfaces, which necessarily incorporate the roughness of the SiC fibers. By properly engineering BN interphase layers to favor outside debonding, it should be possible, not only to delay embrittlement at intermediate temperatures, but also to reduce the effective interfacial shear strength and increase the failure strain and toughness of the composite material. Two techniques have been proposed and partially experimentally verified as candidate means to promote outside debonding in state-of-the-art SiC/SiC composites.

Morscher, Gregory N.↗
NASA NTRS1976

Window defect planar mapping technique

A method of planar mapping defects in a window having an edge surface and a planar surface. The method is comprised of steps for mounting the window on a support surface. Then a light sensitive paper is placed adjacent to the window surface. A light source is positioned adjacent to the window edge. The window is then illuminated with the source of light for a predetermined interval of time. Defects on the surface of the glass, as well as in the interior of the glass are detected by analyzing the developed light sensitive paper. The light source must be in the form of optical fibers or a light tube whose light transmitting ends are placed near the edge surface of the window.

Minton, F. R.↗
NASA NTRSDate not supplied

Degradation of Carbon Fiber Microstructures Due to Oxidative Etch Pitting

In order to understand the influence of etch pits on the material properties of carbon fiber microstructures, we use the Porous Microstructure Analysis (PuMA) software to create realistic pitted structures from virgin fiber structures and then analyze their degradation as the degree of pitting increases. For that purpose, we developed a pitting module within PuMA that creates pits with user-defined geometry (shape, size) and distribution (defect density) on the surface of arbitrary microstructures. In this work, we consider FiberForm microstructures, which are commonly used as the base material for ablative thermal protection systems (TPS). Using the new pitting module, we mimic the evolution of etch pits on FiberForm as it occurs from oxidation in ablative heating environments, by first importing the virgin FiberForm structure from a micrograph scan and then imposing different pitting conditions by varying pit radii and defect densities. We then leverage PuMA’s capabilities to calculate material properties for each structure. The results clearly show the degradation of thermal conductivity and structural integrity as etch pits grow, and furthermore highlight the complex evolution of the surface topology, which results in significant changes of the flowgeometry and chemical gas-surface interactions. Furthermore, a comparison of these changes with the case of shrinking fibers, which has heretofore been the standard for modelling ablation of carbon structures, yields significant differences. For example, we observe the formation of small chunks of fibers as pits grow in size, which could be released into the surrounding flow environment as spallation particles. This motivates us to continue our efforts of modelling pitting as an integral part of the structural degradation of carbon fiber structures in oxidation environments, which will ultimately improve our understanding of failure mechanisms in those materials.

PuMA↗
NASA NTRSDate not supplied

Degradation of Carbon Fiber Microstructures Due to Oxidative Etch Pitting

In order to understand the influence of etch pits on the material properties of carbon fiber microstructures, we use the Porous Microstructure Analysis (PuMA) software to create realistic pitted structures from virgin fiber structures and then analyze their degradation as the degree of pitting increases. For that purpose, we developed a pitting module within PuMA that creates pits with user-defined geometry (shape, size) and distribution (defect density) on the surface of arbitrary microstructures. In this work, we consider FiberForm microstructures, which are commonly used as the base material for ablative thermal protection systems (TPS). Using the new pitting module, we mimic the evolution of etch pits on FiberForm as it occurs from oxidation in ablative heating environments, by first importing the virgin FiberForm structure from a micrograph scan and then imposing different pitting conditions by varying pit radii and defect densities. We then leverage PuMA’s capabilities to calculate material properties for each structure. The results clearly show the degradation of thermal conductivity and structural integrity as etch pits grow, and furthermore highlight the complex evolution of the surface topology, which results in significant changes of the flowgeometry and chemical gas-surface interactions. Furthermore, a comparison of these changes with the case of shrinking fibers, which has heretofore been the standard for modelling ablation of carbon structures, yields significant differences. For example, we observe the formation of small chunks of fibers as pits grow in size, which could be released into the surrounding flow environment as spallation particles. This motivates us to continue our efforts of modelling pitting as an integral part of the structural degradation of carbon fiber structures in oxidation environments, which will ultimately improve our understanding of failure mechanisms in those materials.

PuMA↗
NASA NTRS1995

Interfacial Effects on the Thermal and Mechanical Properties of Graphite/Copper Composites

Graphite surfaces are not wet by pure copper. This lack of wetting has been responsible for a debonding phenomenon that has been found in continuous graphite fiber reinforced copper matrix composites subjected to elevated temperatures. By suitably alloying copper, its ability to wet graphite surfaces can be enhanced. Information obtained during sessile drop testing has led to the development of a copper-chromium alloy that suitably wets graphite. Unidirectionally reinforced graphite/copper composites have been fabricated using a pressure infiltration casting procedure. P100 pitch-based fibers have been used to reinforce copper and copper-chromium alloys. X-ray radiography and optical microscopy have been used to assess the fiber distribution in the cast composites. Scanning electron microscopy and Auger electron spectroscopy analyses were conducted to study the distribution and continuity of the chromium carbide reaction phase that forms at the fiber/matrix interface in the alloyed matrix composites. The effects of the chromium in the copper matrix on the mechanical and thermal properties of P100Gr/Cu composites have been evaluated through tensile testing, three-point bend testing, thermal cycling and thermal conductivity calculations. The addition of chromium has resulted in an increased shear modulus and essentially zero thermal expansion in the P100Gr/Cu-xCr composites through enhanced fiber/matrix bonding. The composites have longitudinal tensile strengths in excess of 700 MPa with elastic moduli of 393 GPa. After 100 hr at 760 deg C 84 percent of the as-cast strength is retained in the alloyed matrix composites. The elastic moduli are unchanged by the thermal exposure. It has been found that problems with spreading of the fiber tows strongly affect the long transverse tensile properties and the short transverse thermal conductivity of the P100Gr/Cu-xCr composites. The long transverse tensile strength is limited by rows of touching fibers which are paths of easy crack propagation under low tensile loads. The short transverse thermal conductivity is dictated by the fiber/matrix interface. Conduction across this interface has been estimated to be two orders of magnitude lower than that across the composite. This is due to the mechanical, and not chemical, nature of Gr/Cu bond.

Devincent, Sandra Marie↗