Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “data reduction methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

An algorithm for maximum likelihood estimation using an efficient method for approximating sensitivities

An algorithm for maximum likelihood (ML) estimation is developed primarily for multivariable dynamic systems. The algorithm relies on a new optimization method referred to as a modified Newton-Raphson with estimated sensitivities (MNRES). The method determines sensitivities by using slope information from local surface approximations of each output variable in parameter space. The fitted surface allows sensitivity information to be updated at each iteration with a significant reduction in computational effort compared with integrating the analytically determined sensitivity equations or using a finite-difference method. Different surface-fitting methods are discussed and demonstrated. Aircraft estimation problems are solved by using both simulated and real-flight data to compare MNRES with commonly used methods; in these solutions MNRES is found to be equally accurate and substantially faster. MNRES eliminates the need to derive sensitivity equations, thus producing a more generally applicable algorithm.

Murphy, P. C.↗

Hybrid approach to data reduction for multi-sensor hot wires

A hybrid approach to implementing the calibration equations for a multisensor hot-wire probe is discussed. The approach combines some of the speed of a look-up approach with the moderate storage requirements of direct calculation based on functional fitting. Particular attention is given to timing and storage comparisons for an X-wire probe. The method depends on the oft-employed concept of an effective cooling velocity which is a function only of the bridge output voltage.

Hooper, C. L.↗

Magnetic properties of iron-bearing graphite fibers

Carbon fibers containing ferromagnetically-ordered iron or other transition metals could be used in a variety of lightweight magnetic composites. Intercalation of bulk graphite with CoCl2 or FeCl3, followed by reduction with butyl lithium, did indeed produce magnetic samples; however, the observed room temperature permeabilities (mu) were less than 2 G/Oe. Magnetic data are presented on carbon fibers containing large amounts of elemental iron, which were prepared by a new method. In this method Amoco P-75 fibers were intercalated with Br2 and I2 followed by fluorination, forming CF(0.75). This product was then intercalated with FeCl3. Subsequent heat treatments in oxidizing and reducing atmospheres converted most of the iron to the pure alpha phase. Room temperature permeabilities as large as 40 G/Oe are observed.

Ferrante, R.↗

Analysis of Fade Detection and Compensation Experimental Results in a Ka-Band Satellite System

The frequency bands being used for new satellite communication systems are constantly increasing to accommodate the requirements for additional capacity. At these higher frequencies, propagation impairments that did not significantly affect the signal at lower frequencies begin to have considerable impact. In Ka-band, the next logical commercial frequency band to be used for satellite communication, attenuation of the signal due to rain is a primary concern. An experimental satellite built by NASA, the Advanced Communication Technology Satellite (ACTS), launched in September 1993, is the first US communication satellite operating in the Ka-band. In addition to higher carrier frequencies, a number of other new technologies, including onboard baseband processing, multiple beam antennas, and rain fade detection and compensation techniques, were designed into the ACTS. Verification experiments have been conducted since the launch to characterize the new technologies. The focus of this thesis is to describe and validate the method used by the ACTS Very Small Aperture Terminal (VSAT) ground stations in detecting the presence of fade in the communication signal and to adaptively compensate for it by the addition of burst rate reduction and forward error correction. Measured data obtained from the ACTS program is used to validate the compensation technique. In this thesis, models in MATLAB are developed to statistically characterize the increased availability achieved by the compensation techniques in terms of the bit error rate time enhancement factor. Several improvements to the ACTS technique are discussed and possible implementations for future Ka-band systems are also presented.

Johnson, Sandra↗

An Overview of Prognosis Health Management Research at GRC for Gas Turbine Engine Structures With Special Emphasis on Deformation and Damage Modeling

Herein a general, multimechanism, physics-based viscoelastoplastic model is presented in the context of an integrated diagnosis and prognosis methodology which is proposed for structural health monitoring, with particular applicability to gas turbine engine structures. In this methodology, diagnostics and prognostics will be linked through state awareness variable(s). Key technologies which comprise the proposed integrated approach include 1) diagnostic/detection methodology, 2) prognosis/lifing methodology, 3) diagnostic/prognosis linkage, 4) experimental validation and 5) material data information management system. A specific prognosis lifing methodology, experimental characterization and validation and data information management are the focal point of current activities being pursued within this integrated approach. The prognostic lifing methodology is based on an advanced multi-mechanism viscoelastoplastic model which accounts for both stiffness and/or strength reduction damage variables. Methods to characterize both the reversible and irreversible portions of the model are discussed. Once the multiscale model is validated the intent is to link it to appropriate diagnostic methods to provide a full-featured structural health monitoring system.

Arnold, Steven M.↗

Comparison of Dynamic Stability Testing Techniques with Magnetic Suspension Wind Tunnel

Dynamic stability testing techniques currently utilized at NASA Langley Research Center (LaRC) are conducted in multiple facilities and consists of free flight, forced oscillation, and free-to-oscillate tests. The MIT/NASA/ODU Magnetic Suspension and Balance System (MSBS) has been recommissioned to explore its utility as an additional facility to expand the dynamic stability test capabilities currently available at NASA LaRC. Simulations were created to replicate each current test facility and method as closely as possible. Data collected from the simulated environments was corrupted with replicated noise sources of the different testing environments and then compared to real data collected during tests when such data was available. The corrupted data was then passed through data reduction and System Identification (SID) to estimate the accuracy of the results with the known aerodynamic model that was utilized within the simulation to generate the original data. Magnitudes of noise were varied utilizing Monte Carlo analysis to perform sensitivity analysis of each noise source on the extracted dynamic stability coefficients. Some preliminary results will be presented.

Otoniel Ramirez↗

Comparison of Dynamic Stability Testing Techniques with Magnetic Suspension Wind Tunnel

Dynamic stability testing techniques currently utilized at NASA Langley Research Center (LaRC) are conducted in multiple facilities and consists of free flight, forced oscillation, and free-to-oscillate tests. The MIT/NASA/ODU Magnetic Suspension and Balance System (MSBS) has been recommissioned to explore its utility as an additional facility to expand the dynamic stability test capabilities currently available at NASA LaRC. Simulations were created to replicate each current test facility and method as closely as possible. Data collected from the simulated environments was corrupted with replicated noise sources of the different testing environments and then compared to real data collected during tests when such data was available. The corrupted data was then passed through data reduction and System Identification (SID) to estimate the accuracy of the results with the known aerodynamic model that was utilized within the simulation to generate the original data. Magnitudes of noise were varied utilizing Monte Carlo analysis to perform sensitivity analysis of each noise source on the extracted dynamic stability coefficients. Some preliminary results will be presented.

Otoniel Ramirez↗

Jet Noise Modeling Using an Acoustic Analogy: From Theoretical Formulation to Practical Noise Predictions

In this presentation an overview of the development of an acoustic analogy formulation, and its implementation into a reduced-order prediction method for turbulent jet mixing noise, will be given. The definition and rationale of an acoustic analogy approach to the prediction of flow-generated noise will be provided. A high-level description of the mathematical processes involved will be outlined in the context of a particular formulation developed at NASA Glenn Research Center. The modelling approximations needed to implement the general theoretical formulation into a practical noise prediction tool will be discussed. Sample results obtained using a noise prediction code based on the NASA Glenn formulation, and comparisons with experimental data, will be presented for a series of turbulent jet test cases. A view on the prospects for continued use of acoustic analogy-based methods for the prediction of flow-generated noise and the assessment of noise-reduction technologies will conclude the presentation.

Jet noise↗

The Impact of New Accelerometer Transplant Data (ACH) on GRACE Follow-On Along-Orbit Inter-Satellite Laser Ranging Observations and Monthly Time-Variable Gravity and Mascon Solutions

GRACE-D accelerometer data show significant bias jumps since one month after the launch of the GRACE Follow-On (GRACE-FO) satellites in May 2018, making them inapplicable for correcting GRACE-FO products for non-gravitational accelerations. The GRACE-FO Science Data System (SDS) compensated this issue by transplanting the GRACE-C accelerometer data toward that of GRACE-D. Recently, GRACE-FO SDS implemented an updated transplant method, used in the latest release of GRACE-FO data. Here, we examine the impact of updated accelerometer transplant data (ACH) on GRACE-FO measurements at all levels: (a) Level-1B inter-satellite laser ranging residuals measured along satellite orbit, (b) Level-2 time-variable gravity solutions from all SDS centers (JPL, CSR, and GFZ), and (c) Level-3 mascon solutions. We show that inter-satellite laser ranging residuals are modified at low frequencies below 1 mHz, affecting the along-orbit analysis of large-scale time-variable gravity signals. When mapped into monthly Level-2 spherical harmonic coefficients of geopotential, the low-frequency change in inter-satellite ranging residuals leads to substantial improvement of coefficients associated with resonant orders (i.e., 15, 30, 45, etc.) and C 30 . We also present an improved SLR-derived C 30 which significantly improves the agreement with updated GRACE-FO C 30 at seasonal and interannual timescales. Moreover, we demonstrate the noise reduction in mass change estimates from new GRACE-FO Level-2 data over oceans, Greenland, and Antarctica for all SDS solutions. GRACE-FO mascon solutions show a moderate change in the updated release. Our comprehensive analyses demonstrate high-quality estimates of non-gravitational accelerations by the updated transplant method, resulting in more accurate GRACE-FO time-variable gravity and mass change observations.

Laser ranging interferometer↗

Single-stage evaluation of highly-loaded high-Mach-number compressor stages 5. Data and performance of baseline, corner-blow wall suction and combined corner blow wall suction stator

A single-stage compressor with a rotor tip speed of 1600 ft/sec and a 0.5 hub tip ratio was used to investigate the effects of several stator endwall treatment methods on stage range and performance. These endwall treatment methods consisted of stator corner-blow, annular wall suction upstream of stator leading edge, and combined corner-blow and annular wall suction. The overall stage performance with corner blow was essentially the same as the baseline performance. The performance for the annular wall suction and the combined corner-blow and wall suction showed a reduction in peak efficiency of 2.5 percentage points compared to the baseline data.

Nikkanen, J. P.↗

A reduction in ag./residential signature conflict using principal components analysis of Landsat temporal data

One important objective of a cooperative project between the U.S. Bureau of Census and NASA is to develop the ability to accurately delineate the types of land cover in the urban-rural transition zone of metropolitan areas. The application of principal components analysis to multidate Landsat imagery is being investigated as a method of reducing the overlap between residential and agricultural spectral signatures. The statistical concepts of principal components analysis are discussed, as well as the results of this analysis when applied to multidate Landsat imagery of the Washington, D.C. metropolitan area.

Williams, D. L.↗

Influence of Strain-Gage Balance Characteristics on the Precision Error of the Drag Coefficient

Improvements and results of a new method are presented that computes a pre-test estimate of the precision error of the drag coefficient of a wind tunnel model. The error estimate is defined as the part of the drag coefficient's precision error that is primarily associated with the precision error of the angle of attack measurement and physical characteristics of the chosen strain-gage balance. The method indirectly describes the precision error of the angle of attack measurement by using an assumed balance gage output variation of one microV/V. The physical characteristics of the balance, on the other hand, are described by partial derivatives of the axial and normal forces with respect to the strain-gage outputs. These derivatives can directly be obtained from the data reduction matrix of the balance. The precision error estimate itself is calculated by applying a simple explicit equation that uses the model reference area, the dynamic pressure, the angle of attack, the coefficients of the linear terms of the data reduction matrix, and the electrical output variation of one microvolt per volt as input. Precision errors at constant angle of attack may be visualized as contour plots by plotting them, for example, versus the Mach number and the total pressure. Characteristics of NASA's MC60E balance are used in combination with the reference area of a generic wind tunnel model in order to demonstrate that error estimates are independent of both the balance load format and the units chosen for the description of balance loads, model reference area, and the dynamic pressure. Finally, experimental data from a wind tunnel test of the Ames Check Standard Model in the NASA Ames 11-foot Transonic Wind Tunnel illustrates the application of the method to real-world test data.

precision error↗

Photogrammetric Metrology for the James Webb Space Telescope Integrated Science Instrument Module

The James Webb Space Telescope (JWST) is a 6.6m diameter, segmented, deployable telescope for cryogenic IR space astronomy (approximately 40K). The JWST Observatory architecture includes the Optical Telescope Element and the Integrated Science Instrument Module (ISIM) element that contains four science instruments (SI) including a Guider. The ISM optical metering structure is a roughly 2.2x1.7x2.2m, asymmetric frame that is composed of carbon fiber and resin tubes bonded to invar end fittings and composite gussets and clips. The structure supports the SIs, isolates the SIs from the OTE, and supports thermal and electrical subsystems. The structure is attached to the OTE structure via strut-like kinematic mounts. The ISIM structure must meet its requirements at the approximately 40K cryogenic operating temperature. The SIs are aligned to the structure's coordinate system under ambient, clean room conditions using laser tracker and theodolite metrology. The ISIM structure is thermally cycled for stress relief and in order to measure temperature-induced mechanical, structural changes. These ambient-to-cryogenic changes in the alignment of SI and OTE-related interfaces are an important component in the JWST Observatory alignment plan and must be verified. We report on the planning for and preliminary testing of a cryogenic metrology system for ISIM based on photogrammetry. Photogrammetry is the measurement of the location of custom targets via triangulation using images obtained at a suite of digital camera locations and orientations. We describe metrology system requirements, plans, and ambient photogrammetric measurements of a mock-up of the ISIM structure to design targeting and obtain resolution estimates. We compare these measurements with those taken from a well known ambient metrology system, namely, the Leica laser tracker system. We also describe the data reduction algorithm planned to interpret cryogenic data from the Flight structure. Photogrammetry was selected from an informal trade study of cryogenic metrology systems because its resolution meets sub-allocations to ISIM alignment requirements and it is a non-contact method that can in principle measure six degrees of freedom changes in target location. In addition, photogrammetry targets can be readily related to targets used for ambient surveys of the structure. By thermally isolating the photogrammetry camera during testing, metrology can be performed in situ during thermal cycling. Photogrammetry also has a small but significant cryogenic heritage in astronomical instrumentation metrology. It was used to validate the displacement/deformation predictions of the reflectors and the feed horns during thermal/vacuum testing (90K) for the Microwave Anisotropy Probe (MAP). It also was used during thermal vacuum testing (100K) to verify shape and component alignment at operational temperature of the High Gain Antenna for New Horizons. With tighter alignment requirements and lower operating temperatures than the aforementioned observatories, ISIM presents new challenges in the development of this metrology system.

Nowak, Maria↗

Flight Test Results of an Angle of Attack and Angle of Sideslip Calibration Method Using Output-Error Optimization

As part of a joint partnership between the NASA Aviation Safety Program (AvSP) and the University of Tennessee Space Institute (UTSI), research on advanced air data calibration methods has been in progress. This research was initiated to expand a novel pitot-static calibration method that was developed to allow rapid in-flight calibration for the NASA Airborne Subscale Transport Aircraft Research (AirSTAR) facility. This approach uses Global Positioning System (GPS) technology coupled with modern system identification methods that rapidly computes optimal pressure error models over a range of airspeed with defined confidence bounds. Subscale flight tests demonstrated small 2-σ error bounds with significant reduction in test time compared to other methods. Recent UTSI full scale flight tests have shown airspeed calibrations with the same accuracy or better as the Federal Aviation Administration (FAA) accepted GPS 'four-leg' method in a smaller test area and in less time. The current research was motivated by the desire to extend this method for inflight calibration of angle of attack (AOA) and angle of sideslip (AOS) flow vanes. An instrumented Piper Saratoga research aircraft from the UTSI was used to collect the flight test data and evaluate flight test maneuvers. Results showed that the output-error approach produces good results for flow vane calibration. In addition, maneuvers for pitot-static and flow vane calibration can be integrated to enable simultaneous and efficient testing of each system.

Siu, Marie-Michele↗

Economic impact of fuel properties on turbine powered business aircraft

The principal objective was to estimate the economic impact on the turbine-powered business aviation fleet of potential changes in the composition and properties of aviation fuel. Secondary objectives include estimation of the sensitivity of costs to specific fuel properties, and an assessment of the directions in which further research should be directed. The study was based on the published characteristics of typical and specific modern aircraft in three classes; heavy jet, light jet, and turboprop. Missions of these aircraft were simulated by computer methods for each aircraft for several range and payload combinations, and assumed atmospheric temperatures ranging from nominal to extremely cold. Five fuels were selected for comparison with the reference fuel, nominal Jet A. An overview of the data, the mathematic models, the data reduction and analysis procedure, and the results of the study are given. The direct operating costs of the study fuels are compared with that of the reference fuel in the 1990 time-frame, and the anticipated fleet costs and fuel break-even costs are estimated.

Powell, F. D.↗

T1 VSAT Fade Compensation Statistical Results

New satellite communication systems are steadily seeking to use higher frequency bands to accommodate the requirements for additional capacity. At these higher frequencies, propagation impairments that did not significantly affect the signal at lower frequencies begin to have considerable impact. In Ka-band. the next logical commercial frequency band to be used for satellite communication, attenuation of the signal due to rain is a primary concern. An experimental satellite built by NASA, the Advanced Communication Technology Satellite (ACTS). launched in September 1993, is the first U.S. communication satellite operating in the Ka-band. In addition to higher carrier frequencies, a number of other new technologies, including on-board baseband processing. multiple beam antennas, and rain fade detection and compensation techniques, were designed into the ACTS. Verification experiments have been conducted since the launch to characterize the new technologies. The focus of this paper is to characterize the method used by the ACTS TI Very Small Aperture Terminal (TI VSAT) ground stations in detecting the presence of fade in the communication signal and to adaptively compensate for it by the addition of burst rate reduction and forward error correction. Measured data obtained from the ACTS program was used to validate the compensation technique. A software process was developed and demonstrated to statistically characterize the increased availability achieved by the compensation techniques in terms of the bit error rate time enhancement factor. Several improvements to the ACTS technique are discussed and possible implementations for future Ka band system are offered.

Johnson, Sandra K.↗

Symbolic LTL Compilation for Model Checking: Extended Abstract

In Linear Temporal Logic (LTL) model checking, we check LTL formulas representing desired behaviors against a formal model of the system designed to exhibit these behaviors. To accomplish this task, the LTL formulas must be translated into automata [21]. We focus on LTL compilation by investigating LTL satisfiability checking via a reduction to model checking. Having shown that symbolic LTL compilation algorithms are superior to explicit automata construction algorithms for this task [16], we concentrate here on seeking a better symbolic algorithm.We present experimental data comparing algorithmic variations such as normal forms, encoding methods, and variable ordering and examine their effects on performance metrics including processing time and scalability. Safety critical systems, such as air traffic control, life support systems, hazardous environment controls, and automotive control systems, pervade our daily lives, yet testing and simulation alone cannot adequately verify their reliability [3]. Model checking is a promising approach to formal verification for safety critical systems which involves creating a formal mathematical model of the system and translating desired safety properties into a formal specification for this model. The complement of the specification is then checked against the system model. When the model does not satisfy the specification, model-checking tools accompany this negative answer with a counterexample, which points to an inconsistency between the system and the desired behaviors and aids debugging efforts.

Rozier, Kristin Y.↗