Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “component performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Validation and Verification for INL Modelica-based TEDS models Via Experimental Results

This report provides an overview on the verification and validation (V&V) of the Thermal Energy Distribution System (TEDS) model developed in the Modelica process modeling ecosystem using experimental data. Model development has led to the creation of a dynamic process model of the experimental TEDS facility housed within the Energy Systems Laboratory (ESL) at Idaho National Laboratory (INL). The model was then used during the preconstruction phase of the experimental effort to inform experimental design (e.g., insulation requirements, bypass line placement, expected performance of components) and to test innovative control schemes prior to the initial operation. The TEDS model developed in Modelica includes the primary components of the TEDS experimental unit: a 200kW Chromalox heater; a single-tank packed-bed thermal energy storage system filled with 0.125-inch alumina (Al2O3) beads; an ethylene-glycol-to-Therminol-66 heat exchanger; system piping; five control valves; and all associated temperature, pressure, and volumetric flow sensors. Using the Institute of Electrical and Electronics Engineers (IEEE) V&V methodologies, considered the gold standard in the engineering field, the model was verified using a combination of static analysis, spatial convergence, and regression tests. Then using dynamic time warping (DTW) initial runs to validate and tune the TEDS model versus the experiment were conducted. This tuning method was accomplished using the INL Risk Analysis Virtual ENvironment (RAVEN) software package. Tuning is required to account for physical phenomena that are less understood within the empirical heat transfer correlations. Through the commencement of this work, a systems-level model of TEDS with associated control systems, sensors, piping diameters, and component capabilities has been created. This model was utilized in the pre-experimental phase to inform system design, insulation thicknesses, and potential control schemes to operate the system effectively and safely. Then, initial experimental startup and operational data were used to demonstrate the validation and tuning methodology. This process demonstrates the classical two-step approach of a model informing experimental design followed by the experiment validation and tuning the model.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Strain gauge for testing microreactor hexagonal core blocks in the Single Primary Heat Extraction and Removal Emulator

To support the development and deployment of microreactor technologies, experiments that help verify and validate reactor systems and components are performed at non-nuclear test facilities. The Single Primary Heat Extraction Removal Emulator at Idaho National Laboratory is one of these test facilities and was used to monitor a test article that has a prototypic geometry of a heat-pipe cooled microreactor core block. To collect crucial temperature and strain data during testing, temperature and strain sensing fiber optics were embedded to the surface of the test article using an ultrasonic additive manufacturing technique. To support and provide benchmark strain data for the embedded sensors, a commercial resistive strain gauge was attached. This report will discuss the results from the deployment of the commercial strain gauge which includes the setup/attachment strategies, data acquisition, and analysis of the strain data.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Roadmap to Advance Heliostat Technologies for Concentrating Solar-Thermal Power

Heliostat-based concentrating solar-thermal power (CSP) systems can offer immense potential to provide low-cost, dispatchable renewable thermal and electrical energy to help achieve 100% decarbonized energy infrastructure in the United States. Heliostats are a major capital cost technology and a performance-dominating component of state-of-the-art commercial molten salt towers and Generation 3 CSP systems. In 2021, the U.S. Department of Energy (DOE) Solar Energy Technologies Office (SETO) launched the Heliostat Consortium (HelioCon), a five-year initiative to advance heliostat technologies. The HelioCon mission is threefold: (1) establish strategic core testing and modeling capabilities and infrastructure at national labs; (2) support heliostat technology development in relevant industries; and (3) serve as a central repository to integrate industry, academia, and other stakeholders for heliostat technology research, development, validation, and deployment. In this report, HelioCon presents a roadmapping study on advancing heliostat technologies, intended as a central reference for the whole CSP community.

14 SOLAR ENERGY↗
DOE OSTI2023

Prioritization of Existing Reactor Materials

The Advanced Materials and Manufacturing Technologies (AMMT) Program is aiming at the faster incorporation of new materials and manufacturing technologies into complex nuclear-related systems. An integrated approach, combining advanced characterization, high-throughput and accelerated testing, modeling and simulation, including machine learning and artificial intelligence, will be employed. Although 316H (Fe–[16–18]Cr–[10–14]Ni–[2–3]Mo–[0.04–0.1]C) has been identified as a key alloy to be integrated into the AMMT accelerated alloy qualification approach because of its relevance for many current and future nuclear energy reactors, many other alloys could be considered for the advanced fabrication of innovative, high-performance nuclear components. Argonne National Laboratory (ANL), Idaho National Laboratory (INL), Oak Ridge National Laboratory (ORNL), and Pacific Northwest National Laboratory (PNNL) are collaborating on identifying the most promising alloy candidates relevant for the AMMT Program. A selection criteria matrix was established to evaluate the alloys considering their relative importance and technological readiness levels for nuclear energy applications, with a focus on laser powder bed fusion (LPBF). Because of the broad range of potential candidate alloys, ORNL and INL focused on nickel-based alloys, and ANL and PNNL mainly evaluated iron-based alloys. PNNL previously published material scorecards reports on several key alloys, and this report provides a broader overview of iron- and nickel-based candidate alloys, expending beyond alloys well-known to the nuclear community.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Advanced Laboratory and Field Arrays (ALFA)/Lab Collaboration Project (LCP) for Marine Energy (Final Scientific/Technical Report)

The objective of the Advanced Laboratory and Field Arrays (ALFA) project was to reduce the Levelized Cost of Energy (LCOE) of Marine and Hydrokinetic (MHK) energy by leveraging research, development, and testing capabilities at Oregon State University, University of Washington, and the University of Alaska, Fairbanks. ALFA is a project within the Pacific Marine Energy Center (PMEC; formerly NNMREC), a multi-institution entity with a diverse funding base that focuses on research and development for marine renewables. The ALFA project aimed to accelerate the development of next-generation arrays of wave energy conversion (WEC) and tidal energy conversion (TEC) devices through a suite of field-focused R&D activities spanning a broad range of strategic opportunity areas identified in the Funding Opportunity Announcement: • Device and/or array operation and maintenance (O&M) logistics development; • High-fidelity resource characterization and/or modeling technique development and validation; • Array-specific component technology development (e.g. moorings and foundations, transmission, and other offshore grid components); • Array performance testing and evaluation; and • Novel cost-effective environmental monitoring techniques and instrumentation testing and evaluation. The objective of the Lab Collaboration Project (LCP) was to accelerate the development of next-generation marine energy conversion systems. The LCP aimed to achieve these project objectives in collaboration with the national laboratories by: • Developing concept generation and assessment tools; • Improving access to existing testing resources; • Validating collision risk models between fish and turbines; and • Advancing analysis and simulation capabilities for wave-WEC interactions and PTO analysis in nonlinear ocean waves. The ALFA portion of the project was comprised of six overarching technical tasks: • Task 1: Debris Modeling, Detection and Mitigation; • Task 2: Autonomous Monitoring & Intervention; • Task 3: Resource Characterization for Extreme Conditions; • Task 4: Robust Models for Design of Offshore Anchoring and Mooring Systems; • Task 5: Performance Enhancement for Marine Energy Converter (MEC) Arrays; and • Task 6: Evaluating Sampling Techniques for MHK Biological Monitoring. The LCP was divided into four overarching technical tasks: • Task 7: Project Management and Reporting • Task 8: Novel Design and Assessment Methodologies for Wave Energy Converter Design (Wave- SPARC) • Task 9: Testing Access for Commercial Marine Renewable Energy Technology Developers • Task 10: Quantifying Collision Risk for Fish and Turbines • Task 11: Nonlinear Ocean Waves and PTO Control Strategy Each ALFA/LCP task listed above functioned as a separate and discreet project. A final Technical Report was written for each individual task and these reports were uploaded to OSTI, after receiving DOE approval. The following document is a compilation of each of these final, approved reports arranged as individual chapters.

13 HYDRO ENERGY↗
DOE OSTI2024

A Theoretical Analysis on the Dynamic Behavior and Electromechanical Response of PZT

Piezoelectric materials are used as a power source in stockpile components for safety and reliability assurances. The objective of this project is to gain insights into the fundamental pressure-induced behavior and electromechanical response of lead zirconate titanate (PZT). Specifically, to establish the basis for an accurate, physics-based material model for robust model-based design to rapidly optimize PZT-based materials and components for performance studies. Established ab-initio methods are used to interrogate and understand the dynamic behavior of PZT as a function of composition (50/50, 65/35, 80/20, 95/5) and dopants (La, Nb) to overcome the costly and time-consuming experimental methodologies. New cold curves for pure and doped single-crystal PZT are obtained as the reference equation-of-state (EOS). A negligible change in the pressure responses was observed for the systems and strains studied. Dielectric and piezoelectric responses of pure and doped single-crystal PZT were also calculated as a function of pressure. For undoped PZT, there is a clear and orderly pressure and composition dependence. For doped PZT, there is a significant increase in the responses, but the behavior is very disordered and inconclusive.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Computational Design of Cost-Effective High-Entropy Thermal/Environmental Barrier Coatings

Developing cost-effective thermal/environmental barrier coatings (TEBC) requires balance among various properties including low thermal conductivity, matching coefficient of thermal expansion (CTE), high thermal stability, high fracture toughness, and high recession resistance while being affordable. Low oxygen diffusivity is desirable as it can slow down oxygen transport to reach the underlying bond coating and hence delay oxidation of the bond coating. This project aims to design low-cost high-performance TEBC based on high entropy rare earth disilicates to protect SiC-based ceramic matrix composites from chemical and thermal attack for better performance of components in the hot section of gas turbine engines. To accelerate the TEBC design, we utilize first-principles density functional theory to predict key properties including phase stability, CTE, lattice thermal conductivity, temperature-dependent elastic constants, and oxygen diffusivity. Alloying elements including Yb, Y, Er, Eu, Gd, Lu, La, and Ce are considered, and modeling prediction are compared with available experimental results.

coefficient of thermal expansion↗
DOE OSTI2025

Manufacturability and performance response of developed Ni-based alloys for reactor environments

Under the Advanced Materials and Manufacturing Technologies program, two Ni-based alloys fabricated by laser powder bed fusion (LPBF) at Oak Ridge National Laboratory and by laser powder directed energy deposition (LP-DED) at Idaho National Laboratory have been evaluated: γ′-strengthened Haynes 282 and solution-strengthened Inconel 625. Printing defects were observed in the LPBF 282 alloy fabricated using a Renishaw AM250 machine, likely due to particle spattering during printing. For both the LPBF and LP-DED 282 alloys, annealing at 1,180°C for 1 h resulted in partial recrystallization and a bimodal grain distribution, and subsequent aging for 4 h at 800°C led to the formation of a high density of nano-size γ′-strengthening precipitates. Creep testing performed at 750°C revealed lower creep life and ductility for the LPBF and LP-DED 282 compared with wrought 282. X-ray computed tomography combined with optical and scanning electron microscopy microstructural characterization revealed crack formation in the LPBF 282 alloy during creep testing, initiated either from printing defects or from creep cavitation at grain boundaries. Creep cavitation and cracking at grain boundaries were also observed for the LP-DED 282 alloy, and optimization of the printing strategies and postheat treatments will be needed to fabricate high-performance 282 components for high-temperature nuclear applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Manufacturability and performance response of developed Ni-based alloys for reactor environments

Under the Advanced Materials and Manufacturing Technologies program, two Ni-based alloys fabricated by laser powder bed fusion (LPBF) at ORNL and laser powder directed energy deposition (LP-DED) at INL have been evaluated: γ′-strengthened Haynes 282 and solution-strengthened Inconel 625. Printing defects were observed in the LPBF 282 alloy fabricated using a Renishaw AM250 machine, likely due to particle spattering during printing. For both the LPBF and LP-DED 282 alloys, annealing at 1,180°C for 1 h resulted in partial recrystallization and a bimodal grain distribution, while subsequent aging for 4 h at 800°C led to the formation of a high density of nano size γ′-strengthening precipitates. Creep testing performed at 750°C revealed lower creep life and ductility for the LPBF and LP-DED 282 compared with wrought 282. X-ray computed tomography combined with optical and scanning electron microscopy microstructural characterization revealed crack formation in the LPBF 282 alloy during creep testing, initiated either from printing defects or from creep cavitation at grain boundaries. Creep cavitation and cracking at grain boundaries were also observed for the LP-DED 282 alloy, and optimization of the printing strategies and post heat treatments will be needed to fabricate high performance 282 components for high temperature nuclear applications.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

ZiaCore Critical Experiment Demonstrates Key Technologies for Nuclear Energy Systems

ZiaCore is a LANL Laboratory Directed Research and Development (LDRD) project focused on developing and demonstrating key technologies for future nuclear energy systems. The project itself was split into three tasks: 1) Design of the ZiaCore Reactor, a UO2 fueled, graphite and zirconium-hydride (ZrH) moderated, heat pipe cooled micro-reactor 2) Development of the ZrH and heat pipes components 3) Performance of a critical experiment with a representative portion of the ZiaCore reactor incorporating the ZrH and heat pipes developed and made at LANL.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Shear-Wave Radiation Patterns from Explosive and Earthquake Sources in Scattering, Heterogeneous Media

Distinguishing whether a seismic event is an earthquake or an explosion is a core problem in explosion monitoring. For simplistic models, earthquakes produce a predictable S-wavefield based on their radiation pattern, while an explosion produces no S-wavefield. However, observations from nuclear tests show that explosions can produce significant S-wave energy on both horizontal components. We perform numerical experiments using SPECFEM to constrain when an S-wavefield generated from an explosion might differ from one produced by an earthquake. We generate the S-wavefield for our explosions by placing the source location within a small region consisting of large velocity heterogeneities. For the 2D cases investigated here, a crucial condition is that the size of the region of heterogeneities must be much smaller (approximately 1/12th) than the minimum wavelength of the wavefield for our simulation setups. We investigate both isotropic heterogeneities and anisotropic heterogeneities. Initial results demonstrate that the heterogeneous region lowers the P/S amplitude ratios of an explosion. The presence of strong anisotropic heterogeneities near the source can also produce an S-wavefield with similar amplitudes to the P-wavefield. Lastly, we show that S-wave polarization angles vary as a function of azimuth and distance for explosive sources in the presence of small-scale heterogeneities.

58 GEOSCIENCES↗
DOE OSTI2023

Degradation of Insulating Glass Units: Thermal Performance, Measurements and Energy Impacts

Insulating glass unit (IGU) degradation has been studied extensively. However, there is limited understanding of how present durability evaluation standards relate to product lifetime. Furthermore, there is debate on how to quantify performance of installed windows over time to better understand degradation processes. More knowledge on these topics is required to link durability evaluation to product lifetime projections based on energy performance. Energy models provide helpful estimations of total annual building energy consumption. However, most models are based on “as installed” performance of envelope components and fail to account for performance degradation. This can lead to an underestimation of building lifetime energy consumption. A better understanding of the relationship between durability and energy performance can inform integration of degradation dynamics into energy modeling software. This will improve lifetime building energy consumption estimations as well as inform appropriate retrofit strategies and timing. This paper reviews current durability literature, various standards for window performance ratings and weathering methods, existing in situ IGU energy performance measurement techniques, and whole-building energy effects. The challenges and disparities among various studies are analyzed and discussed. The authors hope that further work in this area will lead to the development of improved in situ test methods to assess IGU degradation in the field and link this knowledge to improved energy performance modeling approaches.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1972

Nuclear Brayton turboalternator-compressor (TAC) conceptual design study

A comprehensive analysis and conceptual design study of the turboalternator-compressor components was performed using HeXe as the working fluid. Individual turbine, alternator, compressor, and bearing and seal designs were evaluated. Six turboalternator-compressor TAC configurations were completed. One TAC configuration was evaluated to calculate its performance when operating under new cycle conditions,namely, one higher and one lower turbine inlet temperature and one case with krypton as the working fluid. Based on the results, a TAC configuration that incorporated a radial compressor, a radial turbine, a Lundell Alternator, and gas bearings was selected. A new layout of the TAC was prepared that reflects the cycle state points necessary to accommodate a zirconium hydride moderated reactor and a 400 Hz alternator. The final TAC design rotates at 24,000 rpm and produces 160 kWe, 480V, 3-phase, 400 hertz power.

Mock, E. A.↗
NASA NTRS1971

Measurement of differential atomic collision cross sections.

An apparatus for the study of differential angular scattering of atomic projectiles by gas targets is described. The design facilitates system alignment and provides for accurate reproducible location of components. The performance of the instrument is studied for scattering of H+ at 5-25 keV energies by helium and argon targets. Differential cross sections for elastic scattering and charge transfer are presented as well as total charge transfer cross sections. The coefficients for secondary electron ejection by impact of H and H+ on a metal surface are compared.

Fitzwilson, R. L.↗