Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Aerothermal environment of a blunted three-dimensional nonaxisymmetric body at Mach 6.8

Measurements of surface pressure and heat flux at Mach 6.8 for a nonaxisymmetric body, typical of the forward fuselage of an entry vehicle, have been obtained in the Langley 8-ft high-temperature tunnel. Comparisons of these data with predictions obtained from two numerical methods, which treat the test medium as an ideal gas with a laminar boundary layer, are presented. In general, the numerical results are consistent with each other and follow the data in regions of laminar flow; however, the data for angle of attack 14.9 deg indicate transitional flow on most of the windward surface. Also, the two numerical methods disagree slightly in regions of zero or nearly zero pressure gradients.

Martin, F. W., Jr.↗
DOE OSTI2022

Pit Stability Predictions of Additively Manufactured SS316 Surfaces Using Finite Element Analysis

Stainless steels are susceptible to localized forms of corrosion attack, such as pitting. The size and lifetime of a nucleated pit can vary, depending on a critical potential or current density criterion, which determines if the pit repassivates or continues growing. This work uses finite element method (FEM) modeling to compare the critical pit radii predicted by thermodynamic and kinetic repassivation criteria. Experimental electrochemical boundary conditions are used to capture the active pit kinetics. Geometric and environmental parameters, such as the pit shape and size (analogous to additively manufactured lack-of-fusion pores), solution concentration, and water layer thickness were considered to assess their impact on the pit repassivation criterion. The critical pit radius (the transition point from stable growth to repassivation) predicted for a hemispherical pit was larger when using the repassivation potential (E rp ) criteria, as opposed to the current density criteria (pit stability product). Including both the pit stability product and E rp into its calculations, the analytical maximum pit model predicted a critical radius two times more conservative than the FEA approach, under the conditions studied herein. The complex pits representing lack-of-fusion pores were shown to have minimal impact on the critical radius in atmospheric conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1961

Aerodynamic Characteristics in Pitch of a Series of Cruciform-Wing Missiles with Canard Controls at a Mach Number of 2.01

An investigation has been conducted in the Langley 4- by 4-foot supersonic pressure tunnel at a Mach number of 2.01 to determine the static longitudinal stability and control characteristics of a series of missile configurations with canard controls at angles of attack up to about 28 deg. The missiles had cruciform wings and canard surfaces of delta plan form with 70 deg.swept leading edges. Five bodies having fineness ratios of 19.1, 17.7, 16.7, 15.7, and 14.8 were investigated. The results of the investigation indicated a large nonlinear variation of pitching moment with angle of attack for the body of largest fineness ratio that was progressively reduced by decreasing the fineness ratio until it was essentially eliminated for a body of fineness ratio 14.8. The increased linearity of the moment curve would make it possible to reduce the margin of stability so that, for a given canard size and deflection, a higher trim angle of attack might be obtained for the shortest missile than for the longest missile. The pitching-moment results indicated that methods of prediction which assumed linear variations with angle of attack for the wing-alone and wing-plus-interference characteristics were adequate for angles of attack up to about 12 deg. At higher angles of attack it was evident that the characteristics of these components were nonlinear and that more refined methods would be required for adequate prediction.

Spearman, M. Leroy↗
NASA NTRS1993

Vortex features of F-106B aircraft at subsonic speeds

A NASA Langley Research Center flight-research experiment to study the vortex-flow structure and separated-flow origins over an F-106B aircraft wing is described and subsonic 1 g data from various techniques are presented. Off-surface techniques, such as vapor screen, image enhancement, photogrammetry, and computer graphics are integrated to analyze vortex-flow systems. The spatial location of vortex cores and their tracks over the wing are derived from this analysis as a function of angle of attack and Reynolds number. Multiple vortices are observed and are likely attributed to small surface distortions in the wing leading-edge region. Comparisons of off-surface determined vortex core location and reattachment point approximation from the vapor-screen technique are made with those from the on-surface techniques of static pressure and oil flow and show generally good agreement. Wind-tunnel vortex features showed reasonably good agreement with flight results over the forward part of the wing for angles of attack from 16 to 20 deg.

Lamar, John E.↗
NASA NTRS2010

Unified Application of Vapor Screen Flow Visualization and Pressure Sensitive Paint Measurement Techniques to Vortex- and Shock Wave-Dominated Flow Fields

Laser vapor screen (LVS) flow visualization and pressure sensitive paint (PSP) techniques were applied in a unified approach to wind tunnel testing of slender wing and missile configurations dominated by vortex flows and shock waves at subsonic, transonic, and supersonic speeds. The off-surface cross-flow patterns using the LVS technique were combined with global PSP surface static pressure mappings to characterize the leading-edge vortices and shock waves that coexist and interact at high angles of attack. The synthesis of LVS and PSP techniques was also effective in identifying the significant effects of passive surface porosity and the presence of vertical tail surfaces on the flow topologies. An overview is given of LVS and PSP applications in selected experiments on small-scale models of generic slender wing and missile configurations in the NASA Langley Research Center (NASA LaRC) Unitary Plan Wind Tunnel (UPWT) and 8-Foot Transonic Pressure Tunnel (8-Foot TPT).

Erickson, Gary E.↗
NASA NTRS1993

Wind-tunnel free-flight investigation of a supersonic persistence fighter

Wind-tunnel free-flight tests have been conducted in the Langley 30- by 60-Foot Wind Tunnel to examine the high-angle-of-attack stability and control characteristics and control law design of a supersonic persistence fighter (SSPF) at 1 g flight conditions. In addition to conventional control surfaces, the SSPF incorporated deflectable wingtips (tiperons) and pitch and yaw thrust vectoring. A direct eigenstructure assignment technique was used to design control laws to provide good flying characteristics well into the poststall angle-of-attack region. Free-flight tests indicated that it was possible to blend effectively conventional and unconventional control surfaces to achieve good flying characteristics well into the poststall angle-of-attack region.

Hahne, David E.↗
NASA NTRS1955

An Evaluation of the Roll-Rate Stabilization System of the Sidewinder Missile at Mach Numbers from 0.9 to 2.3

A linear stability analysis and flight-test investigation has been performed on a rolleron-type roll-rate stabilization system for a canard-type missile configuration through a Mach number range from 0.9 to 2.3. This type damper provides roll damping by the action of gyro-actuated uncoupled wing-tip ailerons. A dynamic roll instability predicted by the analysis was confirmed by flight testing and was subsequently eliminated by the introduction of control-surface damping about the rolleron hinge line. The control-surface damping was provided by an orifice-type damper contained within the control surface. Steady-state rolling velocities were at all times less than 1 radian per second between the Mach numbers of 0.9 to 2.3 on the configurations tested. No adverse longitudinal effects were experienced in flight because of the tendency of the free-floating rollerons to couple into the pitching motion at the low angles of attack and disturbance levels investigated herein after the introduction of control-surface damping.

Nason, Martin L.↗
NASA NTRS1957

Investigation at High Subsonic Speeds of the Static Longitudinal and Lateral Stability Characteristics of Two Canard Airplane Configurations

The present investigation was conducted in the Langley high-speed 7-by 10-foot tunnel to determine the static longitudinal and lateral stability characteristics at high subsonic speeds of two canard airplane configurations previously tested at supersonic speeds. The Mach number range of this investigation extended from 0.60 to 0.94 and a maximum angle-of-attack range of -2dewg to 24deg was obtained at the lowest test Mach number. Two wing plan forms of equal area were studied in the present tests; one was a 60deg delta wing and the other was a trapezoid wing having an aspect ratio of 3, taper ratio of 0.143, and an unswept 80-percent-chord line. The canard control had a trapezoidal plan form and its area was approximately 11.5 percent of the wing area. The model also had a low-aspect-ratio highly swept vertical tail and twin ventral fins. The longitudinal control characteristics of the models were consistent with past experience at low speed on canard configurations in that stalling of the canard surface occurred at moderate and high control deflections for moderate values of angle of attack. This stalling could impose appreciable limitations on the maximum trim-lift coefficient attainable. The control effectiveness and maximum value of trim-lift was significantly increased by addition of a body flap having a conical shape and located slightly behind the canard surface on the bottom of the body. Addition of the canard surface at 0deg deflection had relatively little effect on overall directional stability of the delta-wing configuration; however, deflection of the canard surface from 0deg to 10deg had a large favorable effect on directional stability at high angles of attack for both the trapezoid- and delta-wing configurations.

Sleeman, William C., Jr.↗
NASA NTRS1973

Impinging jet separators for liquid metal magnetohydrodynamic power cycles

In many liquid metal MHD power, cycles, it is necessary to separate the phases of a high-speed liquid-gas flow. The usual method is to impinge the jet at a glancing angle against a solid surface. These surface separators achieve good separation of the two phases at a cost of a large velocity loss due to friction at the separator surface. This report deals with attempts to greatly reduce the friction loss by impinging two jets against each other. In the crude impinging jet separators tested to date, friction losses were greatly reduced, but the separation of the two phases was found to be much poorer than that achievable with surface separators. Analyses are presented which show many lines of attack (mainly changes in separator geometry) which should yield much better separation for impinging jet separators).

Bogdanoff, D. W.↗
NASA NTRS1974

Low-speed aerodynamic characteristics of a 13.1-percent-thick, high-lift airfoil

Experimental study of the low-speed, sectional characteristics of a high-lift airfoil, and comparison of these characteristics with the predictions of the theoretical methods used in the airfoil's design. The 13.1% thick UI-1720 airfoil was found to achieve the predicted maximum lift coefficient of nearly 2.0. No upper-surface flow separation was found below the stall angle of attack of 16 deg; it appeared that stall was due to an abrupt leading-edge flow separation.

Sivier, K. R.↗
NASA NTRS1974

Effects of reaction control system jet flow field interactions on the aerodynamic characteristics of a 0.010-scale space shuttle orbiter model in the Langley Research Center 31 inch CFHT (OA85)

An experimental investigation was conducted to obtain detailed effects on supersonic vehicle hypersonic aerodynamic and stability and control characteristics of reaction control system jet flow field interactions with the local vehicle flow field. A 0.010-scale model was used. Six-component force data and wing, elevon, and body flap surface pressure data were obtained through an angle-of-attack range of -10 to +35 degrees with 0 deg angle of sideslip. The test was conducted with yaw, pitch and roll jet simulation at a free-stream Mach number of 10.3 and reaction control system plume simulation of flight dynamic pressures of 5, 10 and 20 PSF.

Daileda, J. J.↗
NASA NTRS1974

Low-speed aerodynamic characteristics of a 13.1-percent-thick, high-lift airfoil

Low speed sectional characteristics of a high lift airfoil are studied and a comparison is made of those characteristics with the predictions of the theoretical methods used in the airfoil's design. The 13.1 percent-thick, UI-1720 airfoil was found to achieve the predicted maximum lift coefficient of nearly 2.0. No upper-surface, flow separation was found below the stall angle of attack of 16 degrees; it appeared that stall was due to an abrupt leading edge flow separation.

Sivier, K. R.↗
NASA NTRS1979

Subsonic wind-tunnel investigation of leading-edge devices on delta wings (data report)

The drag reduction potential of leading edge devices on delta wings at high lift is presented. Fences, pylon type vortex generators, chordwise slots, and sharp plate extensions were tested on wing models with 60 and 74 degree swept blunt leading edges at angles of attack to 32 degrees. Six component balance and leading edge surface pressure measurements were taken with various geometry and spanwise arrangements of the devices. Tables listing the data, without analysis, are presented.

Dhanvada, M. R.↗
NASA NTRS1984

A comparative study of the parabolized Navier-Stokes code using various grid-generation techniques

The parabolized Navier-Stokes (PNS) equations are used to calculate the flow-field characteristics about the hypersonic research aircraft X-24C. A comparison of the results obtained using elliptic, hyperbolic, and algebraic grid generators is presented. The outer bow shock is treated as a sharp discontinuity, and the discontinuities within the shock layer are captured. Surface pressures and heat-transfer results at angles of attack of 6 deg and 20 deg, obtained using the three grid generators, are compared. The PNS equations are marched downstream over the body in both Cartesian and cylindrical base coordinate systems, and the results are compared. A robust marching procedure is demonstrated by successfully using large marching step sizes with the implicit shock fitting procedure. A correlation is found between the marching step size, Reynolds number, and the angle of attack at fixed values of smoothing and stability coefficients for the marching scheme.

Kaul, U. K.↗
NASA NTRS1985

A comparative study of the parabolized Navier-Stokes code using various grid-generation techniques

The parabolized Navier-Stokes (PNS) equations are used to calculate the flow-field characteristics about the hypersonic research aircraft X-24C. A comparison of the results obtained using elliptic, hyperbolic and algebraic grid generators is presented. The outer bow shock is treated as a sharp discontinuity, and the discontinuities within the shock layer are captured. Surface pressures and heat-transfer results at angles of attack of 6 deg and 20 deg, obtained using the three grid generators, are compared. The PNS equations are marched downstream over the body in both Cartesian and cylindrical base coordinate systems, and the results are compared. A robust marching procedure is demonstrated by successfully using large marching-step sizes with the implicit shock fitting procedure. A correlation is found between the marching-step size, Reynolds number and the angle of attack at fixed values of smoothing and stability coefficients for the marching scheme.

Kaul, U. K.↗
NASA NTRS1988

Computational validation of a parabolized Navier-Stokes solver on a sharp-nose cone at hypersonic speeds

Perfect gas computational results from a newly-developed upwind, parabolized Navier-Stokes (PNS) solver are compared with an existing set of experimental laminar results for a 10-deg half-angle circular cone at freestream Mach number of 7.95. Comparisons were performed with surface pressure and heat transfer data, as well as with flowfield pitot measurements. The PNS code predicted the surface quantities accurately up through 20-deg angle-of-attack, including crossflow separation, and correctly defined the location of the bow shock and the edge of the boundary layer. The importance of cell Reynolds number, grid density, and thermal boundary conditions to the accurate prediction of the flowfield are examined through numerical emamples.

Huebner, Lawrence D.↗
NASA NTRS1990

Laser transit anemometer measurements on a slender cone in the Langley unitary plan wind tunnel

A laser transit anemometer (LTA) system was used to probe the boundary layer on a slender (5 degree half angle) cone model in the Langley unitary plan wind tunnel. The anemometer system utilized a pair of laser beams with a diameter of 40 micrometers spaced 1230 micrometers apart to measure the transit times of ensembles of seeding particles using a cross-correlation technique. From these measurements, boundary layer profiles around the model were constructed and compared with CFD calculations. The measured boundary layer profiles representing the boundary layer velocity normalized to the edge velocity as a function of height above the model surface were collected with the model at zero angle of attack for four different flow conditions, and were collected in a vertical plane that bisected the model's longitudinal center line at a location 635 mm from the tip of the forebody cone. The results indicate an excellent ability of the LTA system to make velocity measurements deep into the boundary layer. However, because of disturbances in the flow field caused by onboard seeding, premature transition occurred implying that upstream seeding is mandatory if model flow field integrity is to be maintained. A description and results of the flow field surveys are presented.

Humphreys, William M., Jr.↗
NASA NTRS1993

Coating A Bearing With Oxygen-Compatible Material

Laser powder-injection process developed to coat contact surfaces of shaft and hydrostatic bearing with alloy protecting against attack by liquid or gaseous oxygen. Protective alloy is INCO MA 754 (or equivalent). Forms coat uniform, dense, and hard. Has low coefficient of friction and wears negligibly. Does not ignite and burn in high-pressure oxygen. With it, underlying shaft and bearing alloy selected for strength and low thermal expansion rather than compatibility with oxygen.

Funkhouser, Merle E.↗