Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “accelerated aging”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Early age strength increase of fly ash blended cement by a ternary hardening accelerating admixture

The applicability of a combination of sodium thiocyanate (NaSCN), diethanolamine (DEA) and glycerol (Gly) with small dosages as a ternary hardening accelerating admixture for fly ash blended cement (OPC-FA) was studied. The ternary admixture induced higher early and later age mortar strength at both low (5 °C) and normal (20 °C) temperature. Despite used in lower dosage the ternary admixture led to higher strength of the investigated OPC-FA system than other chemicals (e.g. sodium sulfate). Results obtained from isothermal calorimetry, thermogravimetric analysis (TGA) and X-ray diffraction (XRD) showed that the ternary admixture accelerated the cement hydration and increased the amount of AFm (notably calcium hemicarboaluminate hydrate) in the hydration products. A synergistic effect between the three components of the accelerator on the hydration of OPC-FA system was observed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fast-Charging Aging Considerations: Incorporation and Alignment of Cell Design and Material Degradation Pathways

Fast charging of batteries for electric vehicles is seen as one of the most direct ways to enhance adoption. Currently, fast charging is limited by increased cell aging, which is primarily driven by Li plating and degradation of cathode materials. Here, using combined sets of experimental and computational analysis and a suite of different charge protocols, we begin to examine the interplay between failure mode, cell designs, and ultimately aging mechanisms. Slight variation in cell design and the subsequent impacts that charge protocols have on aging can create distinct cell-to-cell variation. As little as 2% difference in porosity change at the cell negative electrode during cycling due to early Li metal plating has been found to alter the aging pathway and either accelerate or inhibit the loss due to Li plating.

25 ENERGY STORAGE↗
DOE OSTI2015

Increased extracellular and intracellular Ca{sup 2+} lead to adipocyte accumulation in bone marrow stromal cells by different mechanisms

Mesenchymal stem cells found in bone marrow stromal cells (BMSCs) are the common progenitors for both adipocyte and osteoblast. An increase in marrow adipogenesis is associated with age-related osteopenia and anemia. Both extracellular and intracellular Ca{sup 2+} ([Ca{sup 2+}]{sub o} and [Ca{sup 2+}]{sub i}) are versatile signaling molecules that are involved in the regulation of cell functions, including proliferation and differentiation. We have recently reported that upon treatment of BMSCs with insulin and dexamethasone, both high [Ca{sup 2+}]{sub o} and high [Ca{sup 2+}]{sub i} enhanced adipocyte accumulation, which suggested that increases in [Ca{sup 2+}]{sub o} caused by bone resorption may accelerate adipocyte accumulation in aging and diabetic patients. In this study, we used primary mouse BMSCs to investigate the mechanisms by which high [Ca{sup 2+}]{sub o} and high [Ca{sup 2+}]{sub i} may enhance adipocyte accumulation. In the process of adipocyte accumulation, two important keys are adipocyte differentiation and the proliferation of BMSCs, which have the potential to differentiate into adipocytes. Use of MTT assay and real-time RT-PCR revealed that high [Ca{sup 2+}]{sub i} (ionomycin)-dependent adipocyte accumulation is caused by enhanced proliferation of BMSCs but not enhanced differentiation into adipocytes. Using fura-2 fluorescence-based approaches, we showed that high [Ca{sup 2+}]{sub o} (addition of CaCl{sub 2}) leads to increases in [Ca{sup 2+}]{sub i}. Flow cytometric methods revealed that high [Ca{sup 2+}]{sub o} suppressed the phosphorylation of ERK independently of intracellular Ca{sup 2+}. The inhibition of ERK by U0126 and PD0325901 enhanced the differentiation of BMSCs into adipocytes. These data suggest that increased extracellular Ca{sup 2+} provides the differentiation of BMSCs into adipocytes by the suppression of ERK activity independently of increased intracellular Ca{sup 2+}, which results in BMSC proliferation. - Highlights: • Both high [Ca{sup 2+}]{sub o} and high [Ca{sup 2+}]{sub i} enhanced adipocyte accumulation in BMSCs. • High [Ca{sup 2+}]{sub i} enhanced the proliferation of BMSCs but not adipocyte differentiation. • High [Ca{sup 2+}]{sub o} suppressed the phosphorylation of ERK in BMSCs. • Inhibition of ERK enhanced the differentiation of BMSCs into adipocytes. • High [Ca{sup 2+}]{sub o}-mediated suppression of ERK may be a new therapy target for anemia.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2026

Organo-mineral interactions in active layer and permafrost soils along aging Arctic landscapes

Rising temperatures are accelerating permafrost thaw, exposing large soil organic carbon (SOC) stocks to microbial decomposition with implications for global climate. Understanding how permafrost carbon is stored and protected through associations with minerals is critical for predicting its vulnerability to decomposition upon thaw. However, how landscape age, substrate chemistry, and soil depth influence mineral associations remain relatively unexplored. We investigated organo-mineral associations in active layer and permafrost soils across a landscape age and geochemical gradient on Alaska’s North Slope, spanning three glaciated (~11,500–125,000 years) and one unglaciated site. Using selective dissolution extractions, X-ray diffraction, and Mössbauer spectroscopy, we characterized minerals and their relationship with SOC. The three recently deglaciated sites had low soil pH that decreased with age and greater abundances of pyrophosphate- and oxalate-extractable Al and Fe, whereas the oldest unglaciated site exhibited near-neutral pH, greater pyrophosphate-extractable Ca, and distinct mineralogy. Across sites, SOC was positively associated with Al and Fe mineral phases, with stronger relationships in acidic soils. Pyrophosphate-extractable Ca also showed strong relationships with SOC at the acidic sites (up to ~10x greater), suggesting that Ca-mediated protection may operate beyond traditionally recognized high-pH soils. Permafrost soils showed depth-related changes in pH, SOC, and Fe mineralogy, suggesting chemically active, heterogeneous layers may shape mineral dynamics and associated carbon. Our results highlight how landscape age, parent material, and depth create distinct geochemical environments that govern mineral-organic associations. As thaw exposes soil to new conditions, these mineral-mediated protection mechanisms may be altered, potentially affecting the permafrost carbon-climate feedback.

Synthetic Biology↗
DOE OSTI2018

Novel preparation of Al-5%Cu / BN and Si3N4 composites with analyzing microstructure, thermal and mechanical properties

Highlights: • The novel MMCs Al5Cu-Si{sub 3}N{sub 4}/BN successfully produced by squeeze casting techniques • Squeeze casting technique improves the wettability between the matrix and nitrides. • XRD analysis showing the presence of new AlN and AlB{sub 2} phases • The hardness curves of the MMCs exhibited the increasing trend till reaching peak. • BN reinforcements significantly accelerate precipitation behavior of Al-5%Cu alloy. - Abstract: The purpose of this research is to develop and characterize composites of Al-5%Cu alloy reinforced by silicon and boron nitride (Si{sub 3}N{sub 4}, BN). The developing of this type of composites gives a new trend of metal matrix composite synthesizing, especially in the case of boron nitride. The stir cast composites showed large areas of porosity and agglomeration. On the other hand, the squeezed cast composites exhibited a fairly uniform particles distribution throughout the matrix alloy. The microstructure and XRD results of the composites confirmed a reaction occurred at the interface between the particles and alloy. AlN and AlB{sub 2} phases were identified in Al5%Cu-Si{sub 3}N{sub 4} and Al5%Cu-BN composites respectively. The ageing results showed that the time to reach peak hardness decreased with addition of the particles. Also, the ageing kinetics was significantly accelerated due to the presence of BN particulates. The coefficient of thermal expansion (CTE) results of the matrix alloy and its composites were practically and theoretically determined. Difference between experimental and calculated values of CTE was less than 8%. Increasing the concentration of Si{sub 3}N{sub 4} increased YS from 215 MPa in the matrix alloy to 285 MPa in the Al-5%Cu-7%Si{sub 3}N{sub 4} composites at a testing temperature of 20 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2013

LUMINOSITY EVOLUTION OF GAMMA-RAY PULSARS

We investigate the electrodynamic structure of a pulsar outer-magnetospheric particle accelerator and the resulting gamma-ray emission. By considering the condition for the accelerator to be self-sustained, we derive how the trans-magnetic-field thickness of the accelerator evolves with the pulsar age. It is found that the thickness is small but increases steadily if the neutron-star envelope is contaminated by sufficient light elements. For such a light element envelope, the gamma-ray luminosity of the accelerator is kept approximately constant as a function of age in the initial 10,000 yr, forming the lower bound of the observed distribution of the gamma-ray luminosity of rotation-powered pulsars. If the envelope consists of only heavy elements, on the other hand, the thickness is greater, but it increases less rapidly than a light element envelope. For such a heavy element envelope, the gamma-ray luminosity decreases relatively rapidly, forming the upper bound of the observed distribution. The gamma-ray luminosity of a general pulsar resides between these two extreme cases, reflecting the envelope composition and the magnetic inclination angle with respect to the rotation axis. The cutoff energy of the primary curvature emission is regulated below several GeV even for young pulsars because the gap thickness, and hence the acceleration electric field, is suppressed by the polarization of the produced pairs.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1989

Update on terrestrial ages of Antarctic meteorites

Cosmic-ray produced Cl-36 (half-life = 3.01 x 10 to the 5th years) has been measured in 90 Antarctic meteorites by accelerator mass spectrometry. The terrestrial ages of the meteorites were calculated from the results. After excluding possible paired objects, 138 terrestrial ages from 18 different locations are available from C-14, Kr-81, and Cl-36 measurements for application to Antarctic meteorite and glaciological studies. The terrestrial ages of Allan Hills meteorites vary from 2000 years to 1 million years and are clearly longer than those of Yamato meteorites and other Antarctic meteorites. The oldest Allan Hills meteorites were found close to the eastern edge and in the southeast of the main icefield. Among all Antarctic meteorites measured to date, only L and LL chondrites have terrestrial ages older than 370,000 years.

Nishiizumi, K.↗
DOE OSTI2017

Accelerated materials evaluation for nuclear applications

This report addresses the opportunities and complexities of using materials test reactors with high neutron fluxes to perform accelerated studies of material aging in power reactors operating at lower neutron fluxes and with different neutron flux spectra. Radiation damage and gas production in different reactors have been compared using the code, SPECTER. This code provides a common standard from which to compare neutron damage data generated by different research groups using a variety of reactors.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Corrigendum to “Accelerated materials evaluation for nuclear applications” [J. Nucl. Mater. 488 (2017) 46–62]

The original article addresses the opportunities and complexities of using materials test reactors with high neutron fluxes to perform accelerated studies of material aging in power reactors operating at lower neutron fluxes and with different neutron flux spectra. Radiation damage and gas production in different reactors have been compared using the code, SPECTER. This code provides a common standard from which to compare neutron damage data generated by different research groups using a variety of reactors. This Corrigendum identifies a few typographical errors. Tables 2 and 3 are included in revised form.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2014

Thermal Performance and Reliability Characterization of Bonded Interface Materials (BIMs): Preprint

Thermal interface materials are an important enabler for low thermal resistance and reliable electronics packaging for a wide array of applications. There is a trend towards bonded interface materials (BIMs) because of their potential for low thermal resistivity (< 1 mm2K/W). However, BIMs induce thermomechanical stresses in the package and can be prone to failures and integrity risks. Deteriorated interfaces can result in high thermal resistance in the package and degradation and/or failure of the electronics. DARPA's Thermal Management Technologies program has addressed this challenge, supporting the development of mechanically-compliant, low resistivity nano-thermal interface (NTI) materials. In this work, we describe the testing procedure and report the results of NREL's thermal performance and reliability characterization of an initial sample of four different NTI-BIMs.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2012

Energy Saving Melting and Revert Reduction Technology: Aging of Graphitic Cast Irons and Machinability

The objective of this task was to determine whether ductile iron and compacted graphite iron exhibit age strengthening to a statistically significant extent. Further, this effort identified the mechanism by which gray iron age strengthens and the mechanism by which age-strengthening improves the machinability of gray cast iron. These results were then used to determine whether age strengthening improves the machinability of ductile iron and compacted graphite iron alloys in order to develop a predictive model of alloy factor effects on age strengthening. The results of this work will lead to reduced section sizes, and corresponding weight and energy savings. Improved machinability will reduce scrap and enhance casting marketability. Technical Conclusions: Age strengthening was demonstrated to occur in gray iron ductile iron and compacted graphite iron. Machinability was demonstrated to be improved by age strengthening when free ferrite was present in the microstructure, but not in a fully pearlitic microstructure. Age strengthening only occurs when there is residual nitrogen in solid solution in the Ferrite, whether the ferrite is free ferrite or the ferrite lamellae within pearlite. Age strengthening can be accelerated by Mn at about 0.5% in excess of the Mn/S balance Estimated energy savings over ten years is 13.05 trillion BTU, based primarily on yield improvement and size reduction of castings for equivalent service. Also it is estimated that the heavy truck end use of lighter castings for equivalent service requirement will result in a diesel fuel energy savings of 131 trillion BTU over ten years.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1999

Bone Density and High Salt Diets in a Space Flight Model

High salt diets accelerate bone loss with aging in patients with postmenopausal osteoporosis except when calcium supplementation is provided. We have observed that the decrease in mineral content of growing femurs in juvenile rats, exposed to a space flight model which unloads the hind limbs , is substantially less in animals fed excess salt. To determine whether excess dietary salt has the same effect on the skeleton of the mature animal whose response to unloading is increased resorption and bone loss rather than impaired growth, we carried out a metabolic study in mature rats with hindlimbs unloaded by tailsuspension.

Arnaud, S. B.↗
NASA NTRS2003

Coordinated turn-and-reach movements. II. Planning in an external frame of reference

The preceding study demonstrated that normal subjects compensate for the additional interaction torques generated when a reaching movement is made during voluntary trunk rotation. The present paper assesses the influence of trunk rotation on finger trajectories and on interjoint coordination and determines whether simultaneous turn-and-reach movements are most simply described relative to a trunk-based or an external reference frame. Subjects reached to targets requiring different extents of arm joint and trunk rotation at a natural pace and quickly in normal lighting and in total darkness. We first examined whether the larger interaction torques generated during rapid turn-and-reach movements perturb finger trajectories and interjoint coordination and whether visual feedback plays a role in compensating for these torques. These issues were addressed using generalized Procrustes analysis (GPA), which attempts to overlap a group of configurations (e.g., joint trajectories) through translations and rotations in multi-dimensional space. We first used GPA to identify the mean intrinsic patterns of finger and joint trajectories (i.e., their average shape irrespective of location and orientation variability in the external and joint workspaces) from turn-and-reach movements performed in each experimental condition and then calculated their curvatures. We then quantified the discrepancy between each finger or joint trajectory and the intrinsic pattern both after GPA was applied individually to trajectories from a pair of experimental conditions and after GPA was applied to the same trajectories pooled together. For several subjects, joint trajectories but not finger trajectories were more curved in fast than slow movements. The curvature of both joint and finger trajectories of turn-and-reach movements was relatively unaffected by the vision conditions. Pooling across speed conditions significantly increased the discrepancy between joint but not finger trajectories for most subjects, indicating that subjects used different patterns of interjoint coordination in slow and fast movements while nevertheless preserving the shape of their finger trajectory. Higher movement speeds did not disrupt the arm joint rotations despite the larger interaction torques generated. Rather, subjects used the redundant degrees of freedom of the arm/trunk system to achieve similar finger trajectories with differing joint configurations. We examined finger movement patterns and velocity profiles to determine the frame of reference in which turn-and-reach movements could be most simply described. Finger trajectories of turn-and-reach movements had much larger curvatures and their velocity profiles were less smooth and less bell-like in trunk-based coordinates than in external coordinates. Taken together, these results support the conclusion that turn-and-reach movements are controlled in an external frame of reference.

NASA Discipline Neuroscience↗
NASA NTRS2011

Uncertainty Analysis in Space Radiation Protection

Space radiation is comprised of high energy and charge (HZE) nuclei, protons, and secondary radiation including neutrons. The uncertainties in estimating the health risks from galactic cosmic rays (GCR) are a major limitation to the length of space missions, the evaluation of potential risk mitigation approaches, and application of the As Low As Reasonably Achievable (ALARA) principle. For long duration space missio ns, risks may approach radiation exposure limits, therefore the uncertainties in risk projections become a major safety concern and methodologies used for ground-based works are not deemed to be sufficient. NASA limits astronaut exposures to a 3% risk of exposure induced death (REID) and protects against uncertainties in risks projections using an assessment of 95% confidence intervals in the projection model. We discuss NASA s approach to space radiation uncertainty assessments and applications for the International Space Station (ISS) program and design studies of future missions to Mars and other destinations. Several features of NASA s approach will be discussed. Radiation quality descriptions are based on the properties of radiation tracks rather than LET with probability distribution functions (PDF) for uncertainties derived from radiobiology experiments at particle accelerators. The application of age and gender specific models for individual astronauts is described. Because more than 90% of astronauts are never-smokers, an alternative risk calculation for never-smokers is used and will be compared to estimates for an average U.S. population. Because of the high energies of the GCR limits the benefits of shielding and the limited role expected for pharmaceutical countermeasures, uncertainty reduction continues to be the optimal approach to improve radiation safety for space missions.

Cucinotta, Francis A.↗
DOE OSTI2015

Predictive Models of Li-ion Battery Lifetime

It remains an open question how best to predict real-world battery lifetime based on accelerated calendar and cycle aging data from the laboratory. Multiple degradation mechanisms due to (electro)chemical, thermal, and mechanical coupled phenomena influence Li-ion battery lifetime, each with different dependence on time, cycling and thermal environment. The standardization of life predictive models would benefit the industry by reducing test time and streamlining development of system controls.

25 ENERGY STORAGE↗
DOE OSTI2017

EVOLUTION OF HIGH-ENERGY PARTICLE DISTRIBUTION IN MATURE SHELL-TYPE SUPERNOVA REMNANTS

Multi-wavelength observations of mature supernova remnants (SNRs), especially with recent advances in γ -ray astronomy, make it possible to constrain energy distribution of energetic particles within these remnants. In consideration of the SNR origin of Galactic cosmic rays and physics related to particle acceleration and radiative processes, we use a simple one-zone model to fit the nonthermal emission spectra of three shell-type SNRs located within 2° on the sky: RX J1713.7−3946, CTB 37B, and CTB 37A. Although radio images of these three sources all show a shell (or half-shell) structure, their radio, X-ray, and γ -ray spectra are quite different, offering an ideal case to explore evolution of energetic particle distribution in SNRs. Our spectral fitting shows that (1) the particle distribution becomes harder with aging of these SNRs, implying a continuous acceleration process, and the particle distributions of CTB 37A and CTB 37B in the GeV range are harder than the hardest distribution that can be produced at a shock via the linear diffusive shock particle acceleration process, so spatial transport may play a role; (2) the energy loss timescale of electrons at the high-energy cutoff due to synchrotron radiation appears to be always a bit (within a factor of a few) shorter than the age of the corresponding remnant, which also requires continuous particle acceleration; (3) double power-law distributions are needed to fit the spectra of CTB 37B and CTB 37A, which may be attributed to shock interaction with molecular clouds.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2015

Submerged Medium Voltage Cable Systems at Nuclear Power Plants: A Review of Research Efforts Relevant to Aging Mechanisms and Condition Monitoring

In a submerged environment, power cables may experience accelerated insulation degradation due to water-related aging mechanisms. Direct contact with water or moisture intrusion in the cable insulation system has been identified in the literature as a significant aging stressor that can affect performance and lifetime of electric cables. Progressive reduction of the dielectric strength is commonly a result of water treeing which involves the development of permanent hydrophilic structures in the insulation coinciding with the absorption of water into the cable. Water treeing is a phenomenon in which dendritic microvoids are formed in electric cable insulation due to electrochemical reactions, electromechanical forces, and diffusion of contaminants over time. These reactions are caused by the combined effects of water presence and high electrical stresses in the material. Water tree growth follows a tree-like branching pattern, increasing in volume and length over time. Although these cables can be “dried out,” water tree degradation, specifically the growth of hydrophilic regions, is believed to be permanent and typically worsens over time. Based on established research, water treeing or water induced damage can occur in a variety of electric cables including XLPE, TR-XLPE and other insulating materials, such as EPR and butyl rubber. Once water trees or water induced damage form, the dielectric strength of an insulation material will decrease gradually with time as the water trees grow in length, which could eventually result in failure of the insulating material. Under wet conditions or in submerged environments, several environmental and operational parameters can influence water tree initiation and affect water tree growth. These parameters include voltage cycling, field frequency, temperature, ion concentration and chemistry, type of insulation material, and the characteristics of its defects. In this effort, a review of academic and industrial literature was performed to identify: 1) findings regarding the degradation mechanisms of submerged cabling and 2) condition monitoring methods that may prove useful in predicting the remaining lifetime of submerged medium voltage power cables. The research was conducted by a multi-disciplinary team, and sources included official NRC reports, national laboratory reports, IEEE standards, conference and journal proceedings, magazine articles, PhD dissertations, and discussions with experts. The purpose of this work was to establish the current state-of-the-art in material degradation modeling and cable condition monitoring techniques and to identify research gaps. Subsequently, future areas of focus are recommended to address these research gaps and thus strengthen the efficacy of the NRC’s developing cable condition monitoring program. Results of this literature review and details of the testing recommendations are presented in this report.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2019

Dielectric Aging and Dielectric Degradation (Breakdown) of Polymer Films in AC Electric Fields

An explanation is proposed for the difference of the electric-strength properties of polymers in dc and ac electric fields. The energy release upon the recombination of electrons and holes injected into a polymer dielectric is considered as a factor accelerating the processes of electric aging of these dielectrics in an ac electric field. It is shown that the nonradiative relaxation of electron excited states, which causes the bond scission in macromolecules and the formation of free radicals, leads to the formation of deep electron traps in the polymer dielectric; as a result, the macromolecule ionization in an electric field is accelerated due to the transition of electrons into these traps. In the solid-state plasma, screening effect, which decreases the molecule ionization potential, appears. As a result, the macromolecule ionization rate, i.e., the rate of charge carrier formation, increases, which leads to a decrease in the lifetime of a polymer dielectric in an ac electric field as compared to the polymer lifetime in a dc electric field.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗