Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Weak form”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Latent Cure Epoxy Resins for Reliable Joints in Secondary-Bonded Composite Structures

In high-performance polymer matrix composite assemblies, adhesive bonding is generally superior to mechanical fastening in structural performance and manufacturing efficiency. However, adhesive bonds are susceptible to minute levels of contamination accumulated during assembly that can lead to unpredictable, weak bonds. Current methods of measuring bond strength are all destructive mechanical tests. To overcome these challenges, redundant load paths (e.g., mechanical fasteners) are often implemented in secondary-bonded, primary-structures, which can greatly reduce structural performance. This study investigated reformulated aerospace epoxy matrix resins with stoichiometric offset to inhibit cure of the matrix resin prior to assembly. Inhibited resins can reflow and mix across the joint interface, which eliminates the material discontinuity and forms a homogenous joint with reliable fracture properties. The goal of this study was to develop and demonstrate secondary composite assemblies that are mechanically and microscopically indistinguishable from a co-cured composite joint. This article describes the development of latent epoxy resins, the fabrication of test articles, and the mechanical properties measured from experimental joints compared with conventional, co-cured laminates. Methods of in-line quality control using and infrared spectroscopy and post-assembly forensics are also described. The final mode-II fracture toughness measured from precracked AERoBOND specimens was similar to that measured from co-cured laminates indicating that later cure epoxy materials could be a suitable replacement for secondary bonding.

Polymer-matrix composites (PMCs)↗

Radiometry with nighttime DMSP images in digital form

The USAF Defense Meteorological Satellite Program (DMSP) spacecraft sends images to earth in the form of numbers. It has been common practice to erase the only digital records, the magnetic tapes, for reuse, after films (resembling photographs) have been created from the numbers. While the DMSP images have been widely used, their application in research has been hindered by both the lack of digital data and the lack of an authoritative source of related technical information. The character of the digital form is considered. Each image is essentially a three-dimensional list (X,Y,Z) in which X and Y represent the position coordinates of a pixel and Z is its associated radiance. Only the value of Z is given and the X-Y position must be deduced from adjunct information. Each original scan composed of 1464 pixels represents an area on the earth's surface about 3 km wide and 3000 km long. Strengths and weaknesses of the system with respect to research applications are considered, and concepts for the design of a nocturnal imager are discussed.

Croft, T. A.↗

2-165 keV observations of active galaxies and the diffuse background

HEAO 1 spectral observations of 12 active galaxies in the 12-165 keV and 2-50 keV ranges are reported. The spectra of these galaxies in the 2-165 keV range are well represented by a single power law model; within experimental uncertainties a narrow dispersion in power law index attributable to the individual galaxies is observed, while the 2-165 keV luminosities of these galaxies ranged from 3 x 10 to the 43rd to 3 x 10 to the 45th ergs/s. An apparent universality of the spectral form is found which can be interpreted as due to a common electron distribution with a temperature of tens of keV in the Compton scattering region or as a common nonthermal power-law distribution generating the observed flux through synchrotron-Compton processes. The data indicate that relativistic particles are likely to be responsible for the X-rays from cores of active galaxies through synchroton-Compton processes. In addition, it is noted that only weak number evolution, if any at all, is present in active galaxies.

Rothschild, R. E.↗

Effects of grain size and grain boundary on critical current density of high T(sub c) superconducting oxides

By means of adding impurity elements in high T sub c oxides, the effects were studied of grain size and grain boundary on the critical current density of the following systems: YBa2Cu3O(7-y) and Bi-Pr-Sr-Ca-Cu-O. In order to only change the microstructure instead of the superconductivity of the grains in the samples, the impurity elements were added into the systems in terms of the methods like this: (1) substituting Y with the lanthanide except Pr, Ce, and Tb in YBa2Cu3O(7-y) system to finning down grains in the samples, therefore, the effect can be investigated of the grain size on the critical current density of 1:2:3 compounds; (2) mixing the high T sub c oxides with the metal elements, such as Ag, according to the composition of (high T sub c oxide)1-xAgx to metallize the grain boundaries in the samples, studying the effect of the electric conductivity of the grain boundaries on the critical current density; (3) adding SiO2, PbO2, and SnO2 into the high T sub c oxide to form impurity phases in the grain boundaries, trying to find out the effects of the impurity phases or metalloid grain boundaries on the critical current density of the high T sub c superconductors. The experimental results indicate that in the case of of the presence of the metalloid grain boundaries finning down grains fails to enhance the j sub c, but restrains it strongly, the granular high T sub c superconductors with the small size grains coupled weakly is always the low j sub c system.

Zhao, Y.↗

Solitary waves in the atmosphere

The weakly nonlinear theory for internal solitary waves is reviewed, and theoretical results of the vertical and horizontal structure of temperature, vertical displacements, and vertical and horizontal perturbations to the wind field associated with steadily propagating solitary waves are presented in two idealized atmospheric configurations. One configuration is representative of solitary waves observed in the lower troposphere and the other of solitary waves that occupy the entire troposphere. The important results of the theory are presented in a form that can be readily used by observationalists. The results obtained are then analyzed using actual rawinsonde data for two well-documented observations of atmospheric solitary waves, which are analogous to the two idealized configurations. The importance and difficulties of properly identifying the waveguide within which the solitary wave is confined are discussed. The fundamental role of a critical level in ducting the disturbances and thus in defining the thickness of the waveguide is illustrated in the example dealing with the solitary wave occupying the entire troposphere. Together, these two examples illustrate the decisions and compromises that must be made in applying the theory to the real atmosphere.

Rottman, James W.↗

Comprehensive investigation of HgCdTe metalorganic chemical vapor deposition

The principal objective of this experimental and theoretical research program was to explore the possibility of depositing high quality epitaxial CdTe and HgCdTe at very low pressures through metalorganic chemical vapor deposition (MOCVD). We explored two important aspects of this potential process: (1) the interaction of molecular flow transport and deposition in an MOCVD reactor with a commercial configuration, and (2) the kinetics of metal alkyl source gas adsorption, decomposition and desorption from the growing film surface using ultra high vacuum surface science reaction techniques. To explore the transport-reaction issue, we have developed a reaction engineering analysis of a multiple wafer-in-tube ultrahigh vacuum chemical vapor deposition (UHV/CVD) reactor which allows an estimate of wafer or substrate throughput for a reactor of fixed geometry and a given deposition chemistry with specified film thickness uniformity constraints. The model employs a description of ballistic transport and reaction based on the pseudo-steady approximation to the Boltzmann equation in the limit of pure molecular flow. The model representation takes the form of an integral equation for the flux of each reactant or intermediate species to the wafer surfaces. Expressions for the reactive sticking coefficients (RSC) for each species must be incorporated in the term which represents reemission from a wafer surface. The interactions of MOCVD precursors with Si and CdTe were investigated using temperature programmed desorption (TPD) in ultra high vacuum combined with Auger electron spectroscopy (AES). These studies revealed that diethyltellurium (DETe) and dimethylcadmium (DMCd) adsorb weakly on clean Si(100) and desorb upon heating without decomposing. These precursors adsorb both weakly and strongly on CdTe(111)A, with DMCd exhibiting the stronger interaction with the surface than DETe.

Raupp, Gregory B.↗

Concerning the Motion and Orientation of Flux Transfer Events Produced by Component and Antiparallel Reconnection

We employ the Cooling et al. (2001) model to predict the location, orientation, motion, and signatures of flux transfer events (FTEs) generated at the solstices and equinoxes along extended subsolar component and high ]latitude antiparallel reconnection curves for typical solar wind plasma conditions and various interplanetary magnetic field (IMF) strengths and directions. In general, events generated by the two mechanisms maintain the strikingly different orientations they begin with as they move toward the terminator in opposite pairs of magnetopause quadrants. The curves along which events generated by component reconnection form bow toward the winter cusp. Events generated by antiparallel reconnection form on the equatorial magnetopause during intervals of strongly southward IMF orientation during the equinoxes, form in the winter hemisphere and only reach the dayside equatorial magnetopause during the solstices when the IMF strength is very large and the IMF points strongly southward, never reach the equatorial dayside magnetopause when the IMF has a substantial dawnward or duskward component, and never reach the equatorial flank magnetopause during intervals of northward and dawnward or duskward IMF orientation. Magnetosheath magnetic fields typically have strong components transverse to events generated by component reconnection but only weak components transverse to the axes of events generated by antiparallel reconnection. As a result, much stronger bipolar magnetic field signatures normal to the nominal magnetopause should accompany events generated by component reconnection. The results presented in this paper suggest that events generated by component reconnection predominate on the dayside equatorial and flank magnetopause for most solar wind conditions.

Sibeck, D. G.↗

Characteristics of downdrafts and turbulence within thunderstorms

Triple Doppler radar observations are presented of downdrafts and turbulence within three convective cloud systems that formed over the South Park region of central Colorado. Downdrafts and turbulence are treated together here because of the relationship suggested by the fact that both can be produced by the mixing of cloudy and dry environmental air. What is more, overlays of estimated turbulent kinetic energy dissipation on general flow patterns yield additional information (including the locations of entrainment) on circulations within convective clouds. The relationship between downdrafts and turbulence is established, and examples are presented of weak to moderate downdrafts and turbulence within three convective storms. The differences in downdraft strength and turbulence intensity in the three cases examined are analyzed.

Knupp, K. R.↗

Magnetotails of the terrestrial planets: A comparative study

Spacecraft observations have established that all of the terrestrial planets interact strongly with the solar wind and possess well developed magnetic tails. At Mercury, Earth, and possibly Mars the tail forms as a result of the solar wind dragging back field lines intrinsic to the planet. Venus differs dramatically from the other planets in that its magnetotail is composed of interplanetary field lines draped about the ionopause. Accordingly, the observations made at the terrestrial planets provide an opportunity to compare not only induced (Venus) magnetic tail properties with those of intrinsic field tails, but also the variation among intrinsic field tails ion the limits of no ionosphere (Mercury), weak intrinsic magnetic field (Mars), and strong magnetic field and ionosphere (Earth). A comparative investigation is made of terrestrial planet magnetotail structure and dynamics. The results are discussed in terms of the physical properties of these planets and their interactions with the solar wind.

Slavin, J. A.↗

The lunar environment and its effect on optical astronomy

The Moon's geologic environment features: (1) gravity field one-sixth that of Earth; (2) sidereal rotation period of 27.3 days; (3) surface with greater curvature than Earth's surface (a chord along a 10 km baseline would have a bulge of 7.2 m); (4) seismically and tidally stable platform on which to make astronomical observations (most moonquakes have magnitudes of 1 to 2 on the Richter scale, within the earth's seismic noise, resulting in ground motions only 1 nm); (5) tenuous atmosphere (the total mass at night is only 10(exp 4) kg) that has an optical depth of 10(exp -6) and does not cause wind induced stresses and vibrations on structures; (6) large diurnal temperature variation (100 to 385 K in equatorial regions), which telescopes must be designed to withstand; (7) weak magnetic field, ranging from 3 to 330 x 10(exp -9) T, compared to 3 x 10(exp -5) T on Earth at the equator; (8) surface exposed to radiation, the most dangerous of which are high energy (1 to 100 Mev) particles resulting from solar flares; (9) high flux of micrometeorites which are not slowed down from their cosmic velocities because of the lack of air (data indicate that microcraters greater than 10 microns across will form at the rate of 3000/sq m/yr); (10) regolith 2 to 30 m thick which blankets the entire lunar surface (this layer is fine-grained (average grain sizes range from 40 to 268 microns), has a low density (800 to 1000 kg/cu m in the upper few mm, rising to 1500 to 1800 kg/cu m at depths of 10 to 20 cm), is porous (35 to 45 pct), cohesive (0.1 to 1.0 kN/sq m), and has a low thermal diffusivity (0.7 to 1.0 x 110-8 sq m/sec); about 29 pct of the regolith is less than 20 micron in size (this dust could pose a hazard to optical telescopes); (11) rubbly upper several hundred meters in which intact bedrock is uncommon, especially in the lunar highlands; and (12) craters with diameter-to-depth ratios of 5 if fresh and less than km across (larger and eroded craters have diameter-to-depth ratios greater than 5).

Taylor, G. Jeffrey↗

Atmospheric Transport During the Transport and Chemical Evolution over the Pacific TRACE-P Experiment

Atmospheric transport over the Pacific Basin is described during NASA's Transport and Chemical Evolution Over the Pacific Experiment (TRACE-P) that was conducted between February - April 2001. The mission included extensive chemical sampling from two aircraft based primarily in Hong Kong and Yokota Air Base, Japan. Meteorological conditions during TRACE-P changed rapidly due to the seasonal winter/spring transition and the decay of prolonged ENSO cold phase (La Nina) conditions. To document these changes, TRACE-P was divided into two halves, and mean flow patterns during each half are presented and discussed. Important circulation features are the semi-permanent Siberian anticyclone and transient middle latitude cyclones that form near eastern Asia and then move eastward over the northern Pacific. Five-day backward trajectories from the various flight tracks show that air sampled by the aircraft had been transported from a variety of locations. Some parcels remained over the tropical western North Pacific during the entire period, while other important origins were Southeast Asia, Africa, and central Asia. Patterns of satellite-derived precipitation and lightning are described. TRACE-P occurs during a neutral to weak La Nina period of relatively cold sea surface temperatures in the tropical Pacific. Compared to climatology, the TRACE-P period exhibits deep convection located west of its typical position; however, tropospheric flow patterns do not exhibit a strong La Nina signal. Circulation patterns during TRACE-P are found to be generally similar to those during NASA's PEM WEST-B mission that occurred in the same region during February - March 1994.

Fuelberg, Henry E.↗

Impact histories inferred from exogenic boulders on asteroids Ryugu and Bennu

Rubble-pile asteroids, such as (162173) Ryugu and (101955) Bennu, are formed as a result of catastrophic disruption of a parent body and re-accumulation of the fragments by self-gravity. Therefore, reaccumulated rubble piles could include mixtures of materials from both the parent body and its catastrophic impactor, as they did in the case of 2008 TC3 and the Almahata Sitta meteorites (Jenniskens et al. 2009). Indeed, six unusually bright, basaltic, meter-scale boulders were recently identified on Bennu’s dark surface (DellaGiustina et al. 2021), and their close spectral matches to the Howardite-Eucrite-Diogenite (HED) meteorites and Vesta family members indicate that they originated from asteroid (4) Vesta. In parallel, bright exogenic anhydrous-silicate–rich materials were found on Ryugu (Tatsumi et al. 2021). The bright boulders on Ryugu are consistent with ordinary chondrite meteorites, based on their albedo and weak or even absent absorption band at 2 µm. These exogenous materials on the surfaces of rubble-pile asteroids could be a key to constraining their specific impact conditions and collisional evolution. In this study, we report further study of the visible spectrophotometry and morphology of exogenic boulders on Ryugu and Bennu using two multi-band cameras: the telescopic Optical Navigation Camera (ONC-T) onboard the Hayabusa2 spacecraft, and MapCam onboard the Origins, Spectral Interpretation, Resource Identification, and Security–Regolith Explorer (OSIRIS-REx) spacecraft, respectively. For Ryugu, we first detected objects with peak reflectance brighter by a factor of >1.5 than the surrounding area. Tatsumi et al. (2021) found two spectral groups among the bright boulders: S-type with an absorption near 1 µm and C/X-type with a flat spectrum. That study found 6 S-types and 15 C/X-types, and in this work we additionally find one S-type and ~70 C/X-types. We found that S-type bright boulders follow two parallel trends consistent with space weathering of ordinary chondrites. Fragments from projectiles suggest that Ryugu may not have formed directly from the original parent body, i.e., it is from a second or higher generation of collisional descendants (Sugimoto et al. in revision). For Bennu, we directly surveyed absorption near 1 µm, which is indicative of anhydrous silicates. We propose 77 objects of exogenic origin including 6 boulders previously reported by DellaGiustina et al. (2021). We find that proposed exogenic objects follow two mixing trends with respect to the average spectrum of Bennu (Tatsumi and Popescu et al. submitted). One trend can be explained by mixing with HED as discussed in DellaGiustina et al. (2021), and the other trend can be explained by mixing with another, olivine-rich composition. Near-infrared spectra also support the possibility of multiple compositions among exogenic objects on Bennu. Thus, similar to Ryugu, Bennu could represent a second or higher generation. Using high-resolution images, we found that more than half of the exogenic objects that we identified on Bennu have breccia-like or inclusion-like morphologies. We do not observe a correlation between morphology and spectral shape. Direct comparison of reflectance spectra of exogenic object spectra between Ryugu and Bennu suggests a compositional difference. Furthermore, the number density of exogenic objects > 0.5 m on Bennu is ~40 times that on Ryugu (Tatsumi and Popescu et al. submitted). Bennu exhibits much more contamination from exogenic materials than Ryugu, which likely reflects differences in impact conditions, such as impact velocity and impactor size.

E. Tatsumi↗

Mobile lidar system for measurement of water vapor mixing ratio and ozone number density

The Water Vapor Lidar was modified and extended to make differential absorption measurements of ozone. Water vapor measurements make use of a weak molecular scattering process known as Raman scattering. It is characterized by a shift in wavelength of the scattered beam of light relative to the incident one. Some of the energy of the incident photon is converted to vibrational or rotational energy within the molecule leaving the scattered photon shifted to a slightly longer wavelength. When performing water vapor measurements, profiles are acquired of water vapor mixing ratio from near the ground to beyond 7 km every 2 minutes. By forming a color composite image of the individual profiles, the spatial and temporal evolution of water vapor is visible with vertical resolution of 75 to 150m and temporal resolution of 2 minutes. The ozone lidar is intended for use as a cross calibration facility for other stationary ozone lidar systems. The ozone measurement employs the technique known as differential absorption. The backscattered laser radiation from two different wavelengths is measured. Successful measurements of 308 nm returns were made from 80 km with an averaging period of 6 hours. Using these data and a standard atmosphere density curve, an ozone number density profile was made which agrees very well with the standard ozone curve between 20 and 40 km.

Whiteman, D.↗

Close binding of identity and location in visual feature perception

The binding of identity and location information in disjunctive feature search was studied. Ss searched a heterogeneous display for a color or a form target, and reported both target identity and location. To avoid better than chance guessing of target identity (by choosing the target less likely to have been seen), the difficulty of the two targets was equalized adaptively; a mathematical model was used to quantify residual effects. A spatial layout was used that minimized postperceptual errors in reporting location. Results showed strong binding of identity and location perception. After correction for guessing, no perception of identity without location was found. A weak trend was found for accurate perception of target location without identity. We propose that activated features generate attention-calling "interrupt" signals, specifying only location; attention then retrieves the properties at that location.

Orientation↗

An implicit finite-difference algorithm for hyperbolic systems in conservation-law form

An implicit finite-difference scheme is developed for the efficient numerical solution of nonlinear hyperbolic systems in conservation-law form. The algorithm is second-order time-accurate, noniterative, and in a spatially factored form. Second- or fourth-order central and second-order one-sided spatial differencing are accommodated within the solution of a block tridiagonal system of equations. Significant conceptual and computational simplifications are made for systems whose flux vectors are homogeneous functions (of degree one), e.g., the Eulerian gasdynamic equations. Conservative hybrid schemes, which switch from central to one-sided spatial differencing whenever the local characteristic speeds are of the same sign, are constructed to improve the resolution of weak solutions. Numerical solutions are presented for a nonlinear scalar model equation and the two-dimensional Eulerian gasdynamic equations.

Beam, R. M.↗

Far-infrared observations of thermal dust emission from supernova 1987A

Observations of SN1987A in the spectral range 18-35 microns taken on November 16 and 23, 1988, 632 and 639 days after core collapse, are reported. A strong and rather flat continuum underlies weak fine-structure lines from heavy elements and declines slowly between 24 and 30 microns. The spectral shape indicates thermal emission from an almost featureless dust component, probably graphite, with silicates contributing less than 20 percent of the emitting dust mass. Some of the emission may be an 'echo' of supernova light reflected from a preexisting dust cloud, but a better explanation which can account for the entirety of emission from infrared to gamma wavelengths, is that dust is being formed in the supernova ejecta. This also accounts more naturally for the inferred dust composition.

Moseley, S. H.↗

Strategies for Stabilizing Nitrogenous Compounds in ECLSS Wastewater: Top-Down System Design and Unit Operation Selection with Focus on Bio-Regenerative Processes for Short and Long Term Scenarios

Water recycling and eventual nutrient recovery is crucial for surviving in or past low earth orbit. New approaches and syste.m architecture considerations need to be addressed to meet current and future system requirements. This paper proposes a flexible system architecture that breaks down pretreatment , steps into discrete areas where multiple unit operations can be considered. An overview focusing on the urea and ammonia conversion steps allows an analysis on each process's strengths and weaknesses and synergy with upstream and downstream processing. Process technologies to be covered include chemical pretreatment, biological urea hydrolysis, chemical urea hydrolysis, combined nitrification-denitrification, nitrate nitrification, anammox denitrification, and regenerative ammonia absorption through struvite formation. Biological processes are considered mainly for their ability to both maximize water recovery and to produce nutrients for future plant systems. Unit operations can be considered for traditional equivalent system mass requirements in the near term or what they can provide downstream in the form of usable chemicals or nutrients for the long term closed-loop ecological control and life support system. Optimally this would allow a system to meet the former but to support the latter without major modification.

Lunn, Griffin M.↗

Development of high temperature nickel-base alloys for jet engine turbine bucket applications

A program has been initiated to develop a material with superior properties at elevated temperatures for utilization in turbine blade applications. A nickel-base superalloy can provide the necessary high temperature strength by using the maximum capability of the three available strengthening mechanisms - intermetallic gamma prime precipitation (Ni3Al), solid solution strengthening with refractory and precious metals, and stable carbide formations through the addition of strong carbide forming elements. A stress rupture test at 2000 deg F and 15,000 psi was formulated to approximate the desired properties. By adding varying amounts of refractory metals (Mo, W and Ta) it was possible to statistically analyze the effects of each in a basic superalloy composition containing fixed amounts of Co, Cr, C, B, Sr, and Ni at three separate levels of AL and Ta. Metallographic analysis correlated with the mechanical properties of the alloys; those with few strengthening phases were weak and ductile and those with excessive amounts of intermetallic phases present in undesirable morphologies were brittle.

SUPERALLOY↗