Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WHEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Prototype color field sequential television lens assembly

The design, development, and evaluation of a prototype modular lens assembly with a self-contained field sequential color wheel is presented. The design of a color wheel of maximum efficiency, the selection of spectral filters, and the design of a quiet, efficient wheel drive system are included. Design tradeoffs considered for each aspect of the modular assembly are discussed. Emphasis is placed on achieving a design which can be attached directly to an unmodified camera, thus permitting use of the assembly in evaluating various candidate camera and sensor designs. A technique is described which permits maintaining high optical efficiency with an unmodified camera. A motor synchronization system is developed which requires only the vertical synchronization signal as a reference frequency input. Equations and tradeoff curves are developed to permit optimizing the filter wheel aperture shapes for a variety of different design conditions.

Source record↗

Annular Momentum Control Device (AMCD). Volume 1: Laboratory model development

The annular momentum control device (AMCD) a thin hoop-like wheel with neither shaft nor spokes is described. The wheel floats in a magnetic field and can be rotated by a segmented motor. Potential advantages of such a wheel are low weight, configuration flexibility, a wheel that stiffens with increased speed, vibration isolation, and increased reliability. The analysis, design, fabrication, and testing is described of the laboratory model of the AMCD.

Source record↗

Some effects of adverse weather conditions on performance of airplane antiskid braking systems

The performance of current antiskid braking systems operating under adverse weather conditions was analyzed in an effort to both identify the causes of locked-wheel skids which sometimes occur when the runway is slippery and to find possible solutions to this operational problem. This analysis was made possible by the quantitative test data provided by recently completed landing research programs using fully instrumented flight test airplanes and was further supported by tests performed at the Langley aircraft landing loads and traction facility. The antiskid system logic for brake control and for both touchdown and locked-wheel protection is described and its response behavior in adverse weather is discussed in detail with the aid of available data. The analysis indicates that the operational performance of the antiskid logic circuits is highly dependent upon wheel spin-up acceleration and can be adversely affected by certain pilot braking inputs when accelerations are low. Normal antiskid performance is assured if the tire-to-runway traction is sufficient to provide high wheel spin-up accelerations or if the system is provided a continuous, accurate ground speed reference. The design of antiskid systems is complicated by the necessity for tradeoffs between tire braking and cornering capabilities, both of which are necessary to provide safe operations in the presence of cross winds, particularly under slippery runway conditions.

Horne, W. B.↗

Contour measurement system

A measurement system for measuring the departures from a straight line of discrete track sections of a track along a coal face in a mine employing a vehicle having a pair of spaced wheel assemblies which align with the track is presented. A reference arm pivotally connects between the wheel assemblies, and there is indicating means for measuring the angle of pivot between the arm and each of the wheel assemblies. The length of the device is less than the length of a track section, and thus when one of the wheel assemblies is on one track section and one is on an adjoining track section, the sum of the indicated angles will be indicative of the angle between track sections. Thus, from the length of a track section and angle, the departure of each track section from the line may be calculated.

Currie, J. R.↗

RSRA vertical drag test report

The Rotor Systems Research Aircraft (RSRA), because of its ability to measure rotor loads, was used to conduct an experiment to determine vertical drag, tail rotor blockage, and thrust augmentation as affected by ground clearance and flight velocity. The RSRA was flown in the helicopter configuration at speeds from 0 to 15 knots for wheel heights from 5 to 150 feet, and to 60 knots out of ground effect. The vertical drag trends in hover, predicted by theory and shown in model tests, were generally confirmed. The OGE hover vertical drag is 4.0 percent, 1.1 percent greater than predicted. The vertical drag decreases rapidly as wheel height is reduced, and is zero at a wheel height of 6 feet. The vertical drag also decreases with forward speed, approaching zero at sixty knots. The test data show the effect of wheel height and forward speed on thrust, gross weight capability, and power, and provide the relationships for power and collective pitch at constant gross weight required for the simulation of helicopter takeoffs and landings.

Flemming, R. J.↗

Space telescope - Meeting the pointing control challenge with today's technology

The pointing control system of the Space Telescope, which provides target-to-target maneuvering capability and precision pointing on the target star (with 0.007-arcsec stability and 0.01-arcsec accuracy), is described. Spacecraft attitude control is undertaken by onboard computer processing of attitude and rate sensor data that generates reaction wheel torque commands. The Space Telescope Operations Control Center communicates with the Space Telescope via the synchronous altitude tracking and data relay satellite system, and determines vehicle attitude more precisely by means of sun sensors, magnetometers and fixed-head star trackers. Such disturbance torques as those of gravity gradients and aerodynamics act on the Space Telescope, causing the speeds of the four reaction wheels to increase. In order to prevent the wheels from reaching a speed-saturated condition, a momentum control system is provided for the management of reaction wheel speed buildup. Attention is given to development testing and control hardware investigations and improvements.

Dougherty, H.↗

Study of meshing of beveled gears with normally decreasing arc teeth

The meshing of beveled gears was studied by the direct and inverse approaches. Gear wheels with teeth of equal height are studied, and wheels with normally-decreasing arc teeth. Different coordinate systems are utilized to plot the determination of the rotation of the originating gear wheel and the meshing line of the gear wheel which is cut. Matrices are used to determine the equations of the originating surfaces and the unit vectors of the normals to these originating surfaces.

Litvin, F. L.↗

Emitted vibration measurement device and method

This invention is directed to a method and apparatus for measuring emitted vibrational forces produced by a reaction wheel assembly due to imbalances, misalignment, bearing defects and the like. The apparatus includes a low mass carriage supported on a large mass base. The carriage is in the form of an octagonal frame having an opening which is adapted for receiving the reaction wheel assembly supported thereon by means of a mounting ring. The carriage is supported on the base by means of air bearings which support the carriage in a generally frictionless manner when supplied with compressed air from a source. A plurality of carriage brackets and a plurality of base blocks provided for physical coupling of the base and carriage. The sensing axes of the load cells are arranged generally parallel to the base and connected between the base and carriage such that all of the vibrational forces emitted by the reaction wheel assembly are effectively transmitted through the sensing axes of the load cells. In this manner, a highly reliable and accurate measurment of the vibrational forces of the reaction wheel assembly can be had. The output signals from the load cells are subjected to a dynamical analyzer which analyzes and identifies the rotor and spin bearing components which are causing the vibrational forces.

Gisler, G. L.↗

Spacecraft redesign to reduce microphonic response of a VCO component

Reaction wheel vibration was found to induce out of specification sidebands on the carrier frequencies of some spacecraft components containing mechanical voltage control oscillators (VCOs). Concurrent investigations were performed to redesign the VCOs to reduce their response to the wheel vibration, and to design a reaction wheel isolation system to reduce the vibration input to the affected components. Component level tests indicated that both efforts provided viable solutions. The redesigned VCO will be incorporated into future spacecraft in the series, while affected spacecraft already in production will be retrofitted with the reaction wheel isolation system.

Strain, J. C.↗

Articulated Suspension Without Springs

Wheels negotiate bumps and holes with minimal tilting of vehicle body. In new suspension, wheel climbs obstacle as high as 1 1/2 times its diameter without excessive tilting of chassis. Provides highly stable ride over rough ground for such vehicles as wheelchairs, military scout cars, and police and fire robots. System of levers distributes weight to wheels. Sized to distribute equal or other desired portions of load among wheels.

Bickler, Donald B.↗

Proof of principle model for a lunar dumptruck

A proof-of-principle model of a two wheeled lunar dump truck was designed to display at the 1989 Summer Conference. The dump truck consists of a cylindrical bucket suspended between two wheels with the center of gravity of the bucket lower than the axis of the wheels. This gives the truck great stability in rough terrain. One motor on each wheel controls the movement of the truck and limits the moving parts to only two. The design of the mechanical drive, the electrical system, and the control systems are examined. Conclusion and recommendations are given.

Harvey, Jill Ann↗

The Enabler: A reevaluation of design concepts and construction of a scaled model

The basic objective of the student's work this quarter was to make an in depth examination of the design concepts used on the lunar vehicle 'The Enabler'. Several changes were made to the vehicle including a redesigned wheel, a more compact boom and a reduced articulation angle. The vehicle's final dimensions were determined through an optimization process by defining mathematical equations for several of the vehicle's defined objectives. These included the ability to scale a one meter object, traverse a one meter crevice, and maintain a wheel-to-wheel clearance of three inches while at maximum articulation. The final dimensions of the vehicle were used to construct an approximate 1/4 scale model of the chassis and wheels. The boom, however, was constructed on a 1/5 scale (from the original design). This was due to the redesign of the boom and the limitations of the constructing material and PVC fittings.

Bess, David↗

Analysis of unsteady wave processes in a rotating channel

The impact of passage rotation on the gas dynamic wave processes is analyzed through a numerical simulation of ideal shock-tube flow in a closed rotating-channel. Initial conditions are prescribed by assuming homentropic solid-body rotation. Relevant parameters of the problem such as wheel Mach number, hub-to-tip radius ratio, length-to-tip radius ratio, diaphragm temperature ratio, and diaphragm pressure ratio are varied. The results suggest possible criteria for assessing the consequences of passage rotation on the wave processes, and they may therefore be applicable to pressure-exchange wave rotors. It is shown that for a fixed geometry and initial conditions, the contact interface acquires a distorted three-dimensional time-dependent orientation at non-zero wheel Mach numbers. At a fixed wheel Mach number, the level of distortion depends primarily on the density ratio across the interface as well as the hub-to-tip radius ratio. Rarefaction fronts, shocks, and contact interfaces are observed to propagate faster with increasing wheel Mach number.

Larosiliere, L. M.↗

RATLER: Robotic All-Terrain Lunar Exploration Rover

A robotic rover vehicle designed for use in the exploration of the Lunar surface is described. The Robotic All-Terrain Lunar Exploration Rover (RATLER) is a four wheeled all-wheel-drive dual-body vehicle. A uniquely simple method of chassis articulation is employed which allows all four wheels to remain in contact with the ground, even while climbing over step-like obstacles as large as 1.3 wheel diameters. Skid steering and modular construction are used to produce a simple, rugged, highly agile mobility chassis with a reduction in the number of parts required when compared to current designs being considered for planetary exploration missions. The design configuration, mobility parameters, and performance of several existing RATLER prototypes are discussed.

Purvis, J. W.↗

Analysis of unsteady wave processes in a rotating channel

The impact of passage rotation on the gas dynamic wave processes is analyzed through a numerical simulation of ideal shock-tube flow in a closed rotating-channel. Initial conditions are prescribed by assuming homentropic solid-body rotation. Relevant parameters of the problem such as wheel Mach number, hub-to-tip radius ratio, length-to-tip radius ratio, diaphragm temperature ratio, and diaphragm pressure ratio are varied. The results suggest possible criteria for assessing the consequences of passage rotation on the wave processes, and they may therefore be applicable to pressure-exchange wave rotors. It is shown that for a fixed geometry and initial conditions, the contact interface acquires a distorted three-dimensional time-dependent orientation at non-zero wheel Mach numbers. At a fixed wheel Mach number, the level of distortion depends primarily on the density ratio across the interface as well as the hub-to-tip radius ratio. Rarefaction fronts, shocks, and contact interfaces are observed to propagate faster with increasing wheel Mach number.

Larosiliere, Louis M.↗

Experimental Investigation of the Robinson-Type Cup Anemometer

This report presents the results of wind tunnel tests on a Robinson-type anemometer. The investigation covered force measurements on individual cups, as well as static and dynamic torque measurements and calibrations on complete cup wheels. In the tests on individual cups 5 cup forms were used and in the measurements on complete cup wheels 4 cup wheels with 3 arm lengths for each cup wheel were tested. All the results are presented in graphical form.

Brevoort, M J↗

An Experimental Study of Applied Ground Loads in Landing

Results are presented of an experimental investigation made of the applied ground loads and the coefficient of friction between the tire and the ground during the wheel spin-up process in impacts of a small landing gear under controlled conditions on a concrete landing strip in the Langley impact basin. The basic investigation included three major phases: impacts with forward speed at horizontal velocities up to approximately 86 feet per second, impacts with forward speed and reverse wheel rotation to simulate horizontal velocities up to about 273 feet per second, and spin-up drop tests for comparison with the other tests. In addition to the basic investigation, supplementary tests were made to evaluate the drag-load alleviating effects of prerotating the wheel before impact so as to reduce the relative velocity between the tire and ground. In the presentation of the results, an attempt has been made to interpret the experimental data so as to obtain some insight into the physical phenomena involved in the wheel spin-up process.

Milwitzky, Benjamin↗

Improved All-Terrain Suspension System

Redesigned suspension system for all-terrain vehicle exhibits enhanced ability to negotiate sand and rocks. Improved six-wheel suspension system includes only two links on each side. Bogie tends to pull rear wheels with it as it climbs. Designed for rover vehicle for exploration of Mars, also has potential application in off-road vehicles, military scout vehicles, robotic emergency vehicles, and toys. Predecessors of suspension system described in "Articulated Suspension Without Springs" (NPO-17354), "Four-Wheel Vehicle Suspension System" (NPO-17407), and "High-Clearance Six-Wheel Suspension" (NPO-17821).

Bickler, Donald B.↗