Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “UNLOADING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

The characterization of shape memory effect for low elastic modulus biomedical {beta}-type titanium alloy

This work investigates the textures of biomedical TiNbTaZr alloy rolled by 99% cold reduction ratios in thickness. The relationship between textures and superelasticity of the specimens treated at 873 K and 1223 K for 1.2 ks is studied. The microstructure of tensile specimen is investigated by transmission electron microscopy. Textures of cold-rolled and heat-treated specimens are studied. During unloading, the anisotropy of superelastic strain and pure elastic strain in the heat-treated specimens is observed. Superelastic strain along rolling direction and transverse direction is larger than those along 45 deg. from rolling direction while pure elastic strain shows the highest value along 45 deg. from rolling direction in the specimen treated at 873 K. For the specimen treated at 1223 K, higher pure elastic strain is obtained along rolling direction. The maximum recovered strain around 2.11% is obtained along rolling direction.

36 MATERIALS SCIENCE↗

Measurement of residual stress in quenched 1045 steel by the nanoindentation method

In this paper, the residual stress in quenched AISI 1045 steel was measured by a recently developed nanoindentation technique. Depth control mode was adopted to measure the residual stress. It was found that residual compressive stress was generated in the quenched steel. The material around nanoindents exhibits significant pile-up deformation. A new method was proposed to determine the real contact area for pile-up material on the basis of invariant pile-up morphology of the loaded or unloaded states. The results obtained by the new method were in good agreement with the residual stresses measured by the classical X-ray diffraction (XRD) method. - Research Highlights: {yields} A new method was proposed to measure the real contact area for pile-up materials. {yields} The real contact depth is defined as the sum of h{sub max} and the pile-up height h{sub p}. {yields} The value of residual stress measured by the nanoindentation method was in good agreement with that by the XRD method.

36 MATERIALS SCIENCE↗

Pre-compression effect on microstructure evolution of extruded pure polycrystalline magnesium during reversed tension load

Highlights: • Number of twin variants under compression along ED is dependent on grain orientation. • Tension after pre-compression results in low-SF twinning and secondary twinning. • Secondary twinning is facilitated by increasing pre-compression. • Sub-grains due to twinning enhance material strength. - Abstract: The microstructure evolution of extruded pure polycrystalline magnesium under compression followed by subsequent tension in ambient air was investigated. Solid round dog-bone shaped specimens were compressed along the extrusion direction (ED) to − 7.3% and − 12.8% true strains, respectively, and then tensioned along the ED to failure. Electron backscatter diffraction (EBSD) was used to examine the microstructure evolution using companion specimens unloaded at multiple points along the deformation curves. Pre-compression along the ED resulted in {10 1-bar 2} tension twinning which increased in volume with increasing strain until exhaustion at approximately − 10.5% true strain. Tensile reloading of the pre-compressed specimens led to a combination of low Schmid factor twinning, detwinning, and secondary {10 1-bar 2} tension twinning. Detwinning was more significant than secondary twinning in the − 7.3% pre-compressed specimens, where only one secondary twin variant was observed. {10 1-bar 2} secondary twinning was more significant in the − 12.8% pre-compressed specimens, where up to three secondary twin variants were observed. After complete detwinning of primary twins, the secondary twins were retained and appeared as sub-grains. The residual sub-grains resulted from secondary twinning may provide a strengthening mechanism for wrought Mg alloys.

36 MATERIALS SCIENCE↗

Correlation between structural and mechanical properties of RF magnetron sputter deposited hydroxyapatite coating

Highlights: • Microstructure and mechanical properties of textured hydroxyapatite (HA) coatings were evaluated. • TEM results revealed two types of coating microstructure corresponding to the film texture. • Elastic performance of the coating was determined by the texture of the HA coating. • HA coating with (300) texture showed larger elastic recovery. - Abstract: In the present study hydroxyapatite (HA) thin films with a,b-plain and c-plain preferential orientation were prepared by means of RF-magnetron sputtering with water vapor addition into a working gas atmosphere to investigate the influence of microstructural features on mechanical performance of the coating at nanoscale. The mechanical properties of the HA coatings textured along a,b- and c-axes by nanoindentation conclusively highlight that elastic modulus, H/E ratio, H{sup 3}/E{sup 2} parameter and percent of elastic recovery are determined by preferential orientation of the film. Nanoindentation reveals that the HA films exhibiting (300) texture possess commensurate nanohardness and lower elastic modulus compared to (002) oriented films, indicating that the former films possess higher resistance to cracking. The (002) and (300) textured coatings exhibited a nanohardness of 4.7 ± 2.0 GPa and 4.4 ± 2.2 GPa, respectively. The elastic modulus of the HA film with (300) and (002) preferential orientation was 75 ± 40 GPa and 103 ± 40 GPa, respectively. The HA coating with (300) texture showed a higher percentage of elastic recovery of 92% within unloading than that of the (002) textured film (69%).

36 MATERIALS SCIENCE↗

Microwave dielectric properties and sintering behavior of nano-scaled ({alpha} + {theta})-Al{sub 2}O{sub 3} ceramics

The dielectric properties at microwave frequencies and the microstructures of nano ({alpha} + {theta})-Al{sub 2}O{sub 3} ceramics were investigated. Using the high-purity nano ({alpha} + {theta})-Al{sub 2}O{sub 3} powders can effectively increase the value of the quality factor and lower the sintering temperature of the ceramic samples. Grain growth can be limited with {theta}-phase Al{sub 2}O{sub 3} addition and high-density alumina ceramics can be obtained with smaller grain size comparing to pure {alpha}-Al{sub 2}O{sub 3}. Relative density of sintered samples can be as high as 99.49% at 1400 deg. C for 8 h. The unloaded quality factors Q x f are strongly dependent on the sintering time. Further improvement of the Q x f value can be achieved by extending the sintering time to 8 h. A dielectric constant ({epsilon}{sub r}) of 10, a high Q x f value of 634,000 GHz (measured at 14 GHz) and a temperature coefficient of resonant frequency ({tau}{sub f}) of -39.88 ppm/deg. C were obtained for specimen sintered at 1400 deg. C for 8 h. Sintered ceramic samples were also characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM)

36 MATERIALS SCIENCE↗

Synthesis of low loss, thermally stable Ce{sub x}Y{sub 1-x}TiTaO{sub 6} microwave ceramics

Ce{sub x}Y{sub 1-x}TiTaO{sub 6} ceramics were prepared through the solid-state ceramic route. The materials were sintered in the range 1520-1580 deg. C. The structure of the system was analyzed by X-ray diffraction and Raman spectroscopic methods. The cell parameters of solid solutions were calculated using the least square method. The microstructure was analyzed using scanning electron microscopy. The dielectric constant ({epsilon}{sub r}), temperature coefficient of resonant frequency ({tau}{sub f}) and the unloaded quality factor (Q{sub u}) are measured in the microwave frequency region using cavity resonator method. The dielectric constant increases with higher concentrations of Ce in the solid solutions. Nearly zero temperature coefficient of resonant frequency ({tau}{sub f}) was obtained for Ce{sub 0.24}Y{sub 0.76}TiTaO{sub 6}. The samples are of high quality factor and are useful electronic materials for microwave applications.

36 MATERIALS SCIENCE↗

Structural, spectroscopic and dielectric investigations on Ba{sub 8}Zn(Nb{sub 6-x}Sb{sub x})O{sub 24} microwave ceramics

Ba{sub 8}Zn(Nb{sub 6-x}Sb{sub x})O{sub 24} (x = 0, 0.3, 0.6, 0.9, 1.2, 1.5, 1.8 and 2.4) ceramics were prepared through the conventional solid-state route. The materials were calcined at 1250 {sup o}C and sintered in the range 1400-1425 {sup o}C. The structure of the system was analyzed by X-ray diffraction, Fourier transform infrared and Raman spectroscopic methods. The theoretical and experimental densities were calculated. The microstructure of the sintered pellets was analyzed using scanning electron microscopy. The low frequency dielectric properties were studied in the frequency range 50 Hz-2 MHz. The dielectric constant ({epsilon}{sub r}), temperature coefficient of resonant frequency ({tau}{sub f}) and the unloaded quality factor (Q{sub u}) are measured in the microwave frequency region using cavity resonator method. The {tau}{sub f} values of the samples reduced considerably with the increase in Sb concentration. The materials have intense emission lines in the visible region. The compositions have good microwave dielectric properties and photoluminescence and hence are suitable for dielectric resonator and ceramic laser applications.

36 MATERIALS SCIENCE↗

Miniaturized and reconfigurable notch antenna based on a BST ferroelectric thin film

Highlights: • A miniature and agile antenna based on a BST MIM capacitor is simulated and made. • Mn{sup 2+} doped BST thin films are synthesized by chemical deposition and spin coating. • Permittivity and losses of the BST thin film are respectively 225 and 0.02 at 1 GHz. • A miniaturization rate of 70% is obtained with a MIM capacitance of 3.7 pF. • A frequency tunability of 14.5% and a tunability performance of 0.04 are measured. - Abstract: This work deals with the design, realization and characterization of a miniature and frequency agile antenna based on a ferroelectric Ba{sub 0,80}Sr{sub 0,20}TiO{sub 3} thin film. The notch antenna is loaded with a variable metal/insulator/metal (MIM) capacitor and is achieved by a monolithic method. The MIM capacitance is 3.7 pF, which results in a resonant frequency of 670 MHz compared to 2.25 GHz for the unloaded simulated antenna; the resulting miniaturization rate is 70%. The characterization of the antenna prototype shows a frequency tunable rate of 14.5% under an electric field of 375 kV/cm, with a tunability performance η = 0.04.

36 MATERIALS SCIENCE↗

Graphene-elastomer nanocomposites based flexible piezoresistive sensors for strain and pressure detection

Highlights: • Fabricating flexible piezoresistive sensors based on PDMS/GNPs nanocomposites. • Positive strain sensitive capacity occurs during increasing pressure-loading process but before the threshold of forces loading. • Tunable strain and pressure sensitivity are achieved by controlling GNPs incorporation, and improved to 140 and 260 at 5 wt% GNPs respectively. • Superior dynamic correspondence with applied pressure and relatively high repeatability. • Application of the GNPs/PDMS piezoresistive sensors as detecting the finger motions. - Abstract: Strain and pressure sensitive flexible piezoresistive sensors have been fabricated based on nanocomposites of graphene nanoplatelets (GNPs) and Polydimethylsiloxane (PDMS) elastomer. The strain detective sensors show positive piezoresistive characteristic under diverse levels of static strain up to 20% due to the flexibility and stretchability of PDMS elastomer. Tunable strain sensitivity of GNPs/PDMS piezoresistive sensors can be achieved by controlling GNPs incorporation into PDMS elastomer, which will be improved to 140 at 5 wt% GNPs concentration. In addition, pressure sensitive response, which exists when the pressure loading is less than threshold pressure, also can be observed in GNPs/PDMS piezoresistive sensors. The GNPs network-elastomer nanocomposite based pressure sensors show tunable piezoresistivity in the ranges of ∼260 under increasingly higher GNPs concentrations. During the cyclic pressure loading, the pressure sensitive behavior of GNPs/PDMS nanocomposites manifests a superior dynamic correspondence with applied pressure while the resistance response can retain at a relatively high level under multiple loading-unloading cycles. Since the GNPs/PDMS piezoresistive sensors can not only respond to subtle bending but also distinguish them accurately for detecting the finger motions, it will make the GNPs/PDMS nanocomposite a good candidate for artificial skin and wearable sensor applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

On the feasibility of partial slip reversal and de-twinning during the cyclic loading of TWIP steel

We report that a recently modified Elasto-Plastic Self-Consistent (EPSC) model which empirically accounts for both intergranular and intragranular back stresses has been successfully used to simulate the cyclic (tension-compression) loading behaviour of an Fe-24Mn-3Al-2Si-1Ni-0.06C TWinning Induced Plasticity (TWIP) steel between strain limits of ±1%. Lattice strain measurements acquired via in-situ neutron diffraction were used to further validate the modelling results. An improved prediction of the pronounced Bauschinger effect during unloading is achieved when the reversibility of partial slip in the <112> direction is accounted for. In conclusion, this result indicates a potential contribution of the stress-induced separation of partial dislocations to the observed early yielding at the low strain levels employed in this study. It also raises the possibility that de-twinning events could be operative during load reversal.

36 MATERIALS SCIENCE↗

Novel elastic deformation mechanism in multifunctional Ti–Nb alloy

In-situ high-energy X-ray diffraction was used to reveal a novel elastic deformation mechanism of the polycrystalline Ti-24Nb-4Zr-8Sn alloy under uniaxial compression. These experiments of polycrystal provide direct evidence on anomalous change in full widths at half maximum for {110} β peak during elastic deformation, i.e. peak broadening during unloading and peak narrowing upon loading, which is attributed to the formation of stress-induced irreversible ω phase as clearly demonstrated in single crystal during compression. Difference in modulus between omega and beta phases induces different change in lattice strain causing the broadening and narrowing of diffraction peak near {110} β where actually contains $\{\bar{1120}\}_{\omega}$ under different applied stress. Finally, this study offers new perspectives to investigate intrinsic mechanism on specific phase transformation during elastic deformation.

36 MATERIALS SCIENCE↗

In-situ investigation of stress-induced martensitic transformation in Ti–Nb binary alloys with low Young's modulus [In-situ high-energy X-ray diffraction investigation on stress-induced martensitic transformation in Ti-Nb binary alloys]

Microstructure evolution, mechanical behaviors of cold rolled Ti-Nb alloys with different Nb contents subjected to different heat treatments were investigated. Here, optical microstructure and phase compositions of Ti-Nb alloys were characterized using optical microscopy and X-ray diffractometre, while mechanical behaviors of Ti-Nb alloys were examined by using tension tests. Stress-induced martensitic transformation in a Ti-30. at%Nb binary alloy was in-situ explored by synchrotron-based high-energy X-ray diffraction (HE-XRD). The results obtained suggested that mechanical behavior of Ti-Nb alloys, especially Young's modulus was directly dependent on chemical compositions and heat treatment process. According to the results of HE-XRD, α"-V1 martensite generated prior to the formation of α"-V2 during loading and a partial reversible transformation from α"-V1 to β phase was detected while α"-V2 tranformed to β completely during unloading.

36 MATERIALS SCIENCE↗

In-situ TOF neutron diffraction studies of cyclic softening in superelasticity of a NiFeGaCo shape memory alloy

Real-time in-situ neutron diffraction was conducted during uniaxial cycling compression of a Ni 49.3 Fe 18 Ga 27 Co 5.7 shape memory alloy to explore the mechanism on its superelasticity at room temperature, which was manifested by the almost recoverable large strains and the apparent cyclic softening. Based on the Rietveld refinements, the real-time evolution of volume fraction of martensite was in-situ monitored, indicating the incremental amount of residual martensite with increasing load cycles. Real-time changes in intensities and lattice strains of { hkl } reflections for individual phase were obtained through fitting individual peaks, which reveal the quantitative information on phase transformation kinetics as a function of grain orientation and stress/strain partitioning. Moreover, a large compressive residual stress was evidenced in the parent phase, which should be balanced by the residual martensite after the second unloading cycle. As a result, the large compressive residual stress found in the parent austenite phase may account for the cyclic effect on critical stress required for triggering the martensitic transformation in the subsequent loading.

36 MATERIALS SCIENCE↗

An investigation of geometrically necessary dislocations and back stress in large grained tantalum via EBSD and CPFEM

This study explores the evolution of GNDs and their effects on back stress through experimental and computational methods. Four large-grained tantalum tensile specimens were strained in uniaxial tension, electron backscatter diffraction (EBSD) data were collected, and geometrically necessary dislocation (GND) maps of the four specimens in the unloaded state were produced. EBSD-based GND maps revealed several types of features with high GND content which caused back stress in the specimens. Correlations between five geometrically-based grain boundary (GB) transmission factors and the GB GND content were evaluated, and statistically significant correlations were found for transmission factors based on Livingston and Chalmer’s N factor, Werner and Prantl’s slip transfer number, and GB misorientation. The sign of individual components of the Nye tensor were used to visually and quantitatively identify clustering of GNDs of the same sign, thus giving additional evidence of increasing back stress due to deformation. Deformation of one of the specimens was simulated using multiple CPFEM based modeling approaches and predicted stress-strain responses are compared. The super dislocation model (SD model) — a crystal plasticity finite element method (CPFEM) which incorporates elastic dislocation interactions — was able to isolate impact of back stress on the overall flow stress. The SD model predicted correct stresses when compared with experimental data; however, when the elastic interactions in the SD model were turned off, stress predictions were 25% too low. Thus, demonstrating the importance of incorporating back stress into the model.

42 ENGINEERING↗

The JSNS 2 detector

The JSNS 2 (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) experiment aims to search for oscillations involving a sterile neutrino in the eV 2 mass-splitting range. The experiment will search for the appearance of electron antineutrinos oscillated from muon antineutrinos. The electron antineutrinos are detected via the inverse beta decay process using a liquid scintillator detector. A 1 MW beam of 3 GeV protons incident on a spallation neutron target produces an intense and pulsed neutrino source from pion, muon, and kaon decay at rest. The JSNS detector is located 24 m away from the neutrino source and began operation from June 2020. The detector contains 17 tonnes of gadolinium (Gd) loaded liquid scintillator (LS) in an acrylic vessel, as a neutrino target. It is surrounded by 31 tonnes of unloaded LS in a stainless steel tank. Optical photons produced in LS are viewed by 120 R7081 Hamamatsu 10-inch Photomultiplier Tubes (PMTs). In this study, we describe the JSNS detector design, construction, and operation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Characterization of wellbore casing corrosion product as a permeable porous medium

Leakage along wellbores is of concern for a variety of applications, including sub-surface fluid storage facilities, geothermal wells, and CO 2 storage wells. We have investigated whether corroded casing is permeable to gas and can serve as a leakage pathway along wellbores. Three specimens were prepared from laboratory steel plates corroded using different mechanisms to reflect different possible field conditions and produce a variety of corrosion rates. Single-phase gas flow measurements were made under a range of gas pressures to investigate flow in both the viscous and visco-inertial flow regimes. Tests were conducted at different confining stresses (range from 3.45 to 13.79 MPa) following both loading and unloading paths. The gas flow test results imply corroded casing can serve as a significant leakage path along the axis of a wellbore. Transmissivity was discovered to be sensitive to the variation in confining stress suggesting that the corrosion product is deformable. Gas slip factors and the coefficients of inertial resistance of the corrosion product were comparable to those available in the literature for other porous media. Post-test examination of the corrosion product revealed it to be a heterogeneous, mesoporous material with mostly non-uniform slit type porosity. There was no discernable difference in the composition of corrosion product from specimens corroded by different mechanisms.

02 PETROLEUM↗

SPOUTED BED DESIGN CONSIDERATIONS FOR COATED NUCLEAR FUEL PARTICLES

High Temperature Gas Cooled Reactors (HTGRs) are fueled with tristructural isotropic (TRISO) coated nuclear fuel particles embedded in a carbon-graphite fuel body. TRISO coatings consist of four layers of pyrolytic carbon and silicon carbide that are deposited on uranium ceramic fuel kernels (350µm – 500µm diameters) in a concatenated series of batch depositions. Each layer has dedicated functions such that the finished fuel particle has its own integral containment to minimize and control the release of fission products into the fuel body and reactor core. The TRISO coatings are the primary containment structure in the HTGR reactor and must have very high uniformity and integrity. To ensure high quality TRISO coatings, the four layers are deposited by chemical vapor deposition (CVD) using high purity precursors and are applied in a concatenated succession of batch operations before the finished product is unloaded from the coating furnace. These depositions take place at temperatures ranging from 1230°C to 1550°C and use three different gas compositions, while the fuel particle diameters double, their density drops from 11.1 g/cm3 to 3.0 g/cm3, and the bed volume increases more than 8-fold. All this is accomplished without the aid of sight ports or internal instrumentation that could cause chemical contamination within the layers or mechanical damage to thin layers in the early stages of each layer deposition. The converging section of the furnace retort was specifically designed to prevent bed stagnation that would lead to unacceptably high defect fractions and facilitate bed circulation to avoid large variability in coating layer dimensions and properties. The gas injection nozzle was designed to protect precursor gases from becoming overheated prior to injection, to induce bed spouting and preclude bed stagnation in the bottom of the retort. Furthermore, the retort and injection nozzle designs minimize buildup of pyrocarbon and silicon carbide on the retort wall and manage nozzle orifice accretions. The equipment and operating methods have yielded very good reproducibility in the TRISO coated particles batches.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Discrete element modeling of deformable pinewood chips in cyclic loading test

The design of efficient lignocellulosic biomass feedstock systems is challenging, as current laboratory characterization and design methods were developed primarily for fine powders with relatively low compressibility. Here, the discrete element method (DEM) is gaining prominence as an alternative method for modeling the bulk flow and transport of particulate materials in hoppers and feeders. However, prior DEM simulations investigating the flow of wood chips modeled the particles as simple rigid geometries such as spheres, rods or blocks, and neglected the effects of particle deformability and irregular shapes. As a consequence, those simplified DEM models may not provide enough key diagnosis to help improve the design of biomass feeding and handling equipment. This work presents a bonded-sphere DEM approach for characterizing the mechanical behavior of bulk flexible, deformable pinewood chips in a cyclic stress loading test. Clustered spheres that can bend and twist via elastic bonds are used to model irregular-shape particles in real pinewood chip samples. An axial compression tester, which contains 0.06 million bonded-sphere particles (1.35 million spheres) in a quarter cylinder, is simulated with a domain size similar to the experiments. With careful calibration, the simulations have delivered the bulk densities and the bulk moduli of elasticity that are in good agreement with those measured in the corresponding experiments. However, it is also been found challenging for the present DEM model to accurately predict the overall stress-strain behavior of bulk pinewood chips, especially the large sustained plastic deformation during unloading. Additional numerical tests have shown that the adjustment in certain contact parameters (e.g. bond stiffness) can lead to profound solution improvement, but meanwhile will induce extra challenges such as increased computing time. Future work will include an elasto-plastic particle bond model to enhance the simulation fidelity.

42 ENGINEERING↗