Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ti”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Design of a V–Ti–Ni alloy with superelastic nano-precipitates

Stress-induced martensitic transformations enable metastable alloys to exhibit enhanced strain hardening capacity, leading to improved formability and toughness. As is well-known from transformation-induced plasticity (TRIP) steels, however, the resulting martensite can limit ductility and fatigue life due to its intrinsic brittleness. In this work, we explore an alloy design strategy that utilizes stress-induced martensitic transformations but does not retain the martensite phase. This strategy is based on the introduction of superelastic nano-precipitates, which exhibit reverse transformation after initial stress-induced forward transformation. To this end, utilizing ab-initio simulations and thermodynamic calculations we designed and produced a V 45 Ti 30 Ni 25 (at%) alloy. In this alloy, TiNi is present as nano-precipitates uniformly distributed within a ductile V-rich base-centered cubic (bcc) β matrix, as well as being present as a larger matrix phase. We characterized the microstructure of the produced alloy using various scanning electron microscopy (SEM) and transmission electron microscopy (TEM) methods. Furthermore, the bulk mechanical properties of the alloy are demonstrated through tensile tests, and the reversible transformation in each of the TiNi morphologies were confirmed by in-situ TEM micro-pillar compression experiments, in-situ high-energy diffraction synchrotron cyclic tensile tests, indentation experiments, and differential scanning calorimetry experiments. The observed transformation pathways and variables impacting phase stability are critically discussed.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Mechanical properties of an Al 10 Nb 20 Ta 15 Ti 30 V 5 Zr 20 A2/B2 refractory superalloy and its constituent phases

Refractory superalloys (RSAs) are a new class of high-temperature structural materials consisting of a nanometer-sized mixture of two coherent A2 (disordered BCC) and B2 (ordered) phases. While these RSAs typically exhibit superior mechanical properties at elevated temperatures, they suffer from limited plasticity at lower temperatures, often attributed to the continuous ordered B2 matrix in these two-phase alloys. To knowledgably control the microstructure and mechanical properties of these alloys, the properties of the constitutive phases in RSAs should be known. Currently this information is absent. Here, in the present work, the microstructure and mechanical properties (at 20–1200 °C) of a candidate Al 0.5 NbTa 0.8 Ti 1.5 V 0.2 Zr RSA and two single-phase alloys, which compositions correspond to the compositions of the A2 and B2 phases in the selected RSA, are reported. Interestingly, and quite unexpectedly, the intrinsic mechanical behavior of the constituent A2 and B2 phases, deciphered for the first time in the present study, revealed that they are softer and substantially more ductile than the parent two-phase RSA. Furthermore, the ordered B2 phase exhibits a deformation twinning mechanism leading to twinning induced plasticity (TWIP) coupled with a low APB energy and activity of 1/2<111> dislocations. These mechanisms are thought to be responsible for the high plasticity of the ordered B2 phase. The results presented here question the current assumption that the ordered B2 phase in these RSAs has limited plasticity and strongly indicate that the nature of the B2/A2 interface boundaries and coherency strengthening play an important role in controlling the mechanical properties of the two-phase RSA.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Controls and process planning strategies for 5-axis laser directed energy deposition of Ti-6Al-4V using an 8-axis industrial robot and rotary motion

Interest in multi-axis additive manufacturing has grown significantly in recent years due to associated benefits that range from improved quality to support for greater geometric complexity. A method of 5-axis Laser Hot-Wire Directed Energy Deposition is developed and demonstrated in this study using an 8-axis industrial robot, comprised of a 6-axis serial link robot and a 2 degree-of-freedom positioner. Coordinated 5-axis motion is used to print Ti-6Al-4V objects predominantly through build plate rotation. Methods of slicing and toolpath generation are presented, including the use of an alternating toolpath direction philosophy and the manipulation of the CAD model surface normal vectors for determining the required build plate tilt angles for maintaining consistent deposition orientations relative to gravity. Another objective of the study was to determine the limits of conventional slicing and layer height control techniques for printing geometries with significant unsupported overhangs. A comparison is made between the behavior of normal and conformal bead alignment in this regard, and the performance of the layer height controller is reported as it relates to process stability and the limits of printing overhang geometries. Unsupported overhangs were successfully printed at 35° without build plate tilt and 45° with build plate tilt. Toolpath velocity and net-shape printing performance are reported as well, with 3D scans of the printed surfaces used for net-shape characterization. In all, the printing of three geometries is presented, including the overhang geometry, a 5-axis toolpath geometry, and a large-scale, multi-bead demonstrator part, which exceeded 500 mm in height and weighed 44 kg (97 lbs).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Fatigue performance of laser powder bed fusion hydride-dehydride Ti-6Al-4V powder

We report hydride-dehydride (HDH) Ti-6Al-4V alloy with particle size distribution of 50–120 µm is laser powder bed fusion (L-PBF) processed using optimum processing parameters and a near-fully dense structure with a density of 99.9 % is achieved. Microstructural observations and phase analyses indicate formation of columnar β grains with acicular α/α' phases in as-built condition. The roughness of the as-fabricated samples is significant with an average roughness of R a = 15.71 ± 3.96 µm and a root mean square roughness of R rms = 108.4 ± 24.9 µm, however, both values are reduced to R a = 0.19 ± 0.04 µm and R rms = 4.9 ± 0.6 µm after mechanical grinding. Mechanical tests are carried out on as-fabricated specimens followed by stress relief treatment. All samples are tested to failure in fatigue, under fully-reversed tension-compression conditions of R = –1. The as-built samples failed from the surface with crack initiation mainly at micro-notches, whereas after mechanically grinding, crack initiation changed to subsurface defects such as pores. Minimizing surface roughness by mechanically grinding eliminates surface micro-notches which improves fatigue strength in the high cycle fatigue region. Fatigue notch factor calculations showed that the effect of surface roughness was significantly lower when HDH powder is used compared to standard spherical powder. X-ray diffraction analysis revealed an in-plane compressive stress, micro-strain and grain refinement on the surface of the mechanically ground samples. Fractography observations (macroscale) revealed a fully brittle fracture in the first stage of crack growth with a transition to a dominantly ductile fracture in the third stage of crack growth. On the other hand, at the micro scale, even the brittle fracture regions showed evidence of ductile fracture within the α' martensite laths.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Synergy of tensile strength and high cycle fatigue properties in a novel additively manufactured Al-Ni-Ti-Zr alloy with a heterogeneous microstructure

Alloy design strategies in additive manufacturing (AM) to achieve grain refinement and terminal eutectic solidification have been introduced to engineer Al alloys having microstructural hierarchy and heterogeneity. Such alloy design strategies enable crack-free builds with an expanded AM processing window and pushed the strength limit in Al alloys. However, fatigue performance of Al alloys made by AM is restricted by the presence of process induced defects and its stochasticity. In this work, tensile and high cycle fatigue (HCF) behavior of a novel Al-Ni-Ti-Zr alloy with a heterogeneous microstructure is studied in the as-built condition, supplemented by detailed microstructural and mechanical characterization. Excellent strength-ductility synergy of 342 MPa and 16% failure strain achieved in the alloy was associated with the microstructural attributes that pertain to the novel alloy. Additionally, the alloy showed excellent HCF performance with a fatigue endurance limit to ultimate tensile strength ratio of 0.29 in flexural fatigue mode. The study revealed the existence of multiple crack retardation mechanisms and favorable crack propagation pathways through the fine-grained regions which enabled good fatigue performance to the alloy. Further, a probabilistic model has been used to estimate the fatigue life of the alloy as a function of the stochastic microstructure by utilizing the statistical distribution of pores, solid-state inclusions, and grains in the AM Al alloy. Finally, the model parametric trends are consistent with the experimental observations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Part-scale microstructure prediction for laser powder bed fusion Ti-6Al-4V using a hybrid mechanistic and machine learning model

Laser powder bed fusion (LPBF) Ti-6Al-4V is widely studied for use in structural applications in aerospace and medical industries, but mechanical anisotropy and microstructural inhomogeneity prohibits its wider adoption. Although successful microstructure prediction models have been developed, a remaining challenge is their limited integration across length/time scales and validation by experimental studies. Here, this work proposes a physics-augmented machine learning surrogate model to unite predictions of LPBF temperature, β phase morphology and texture, and α/α’ formation into a single framework that is calibrated and validated with experiments. First, a phase field (PF) model of the martensitic β→α’ transformation is developed and calibrated using data from in-situ synchrotron cyclic heating/cooling studies quantifying the variation of α phase fraction with time. In parallel, an established finite difference-Monte Carlo (FDMC) model predicts the part-scale temperature profile and β grain formation during solidification. A dataset is developed using LPBF cyclic temperature descriptors from the FDMC model as inputs and corresponding α/α’ phase fraction and width from the PF model as outputs. Five machine learning (ML) regression models are tested and optimized, having mean absolute error in testing ≤ 4 %, and the k-nearest neighbors (KNN) model is selected as the best performing. The KNN model is called at the nodal level during post-processing of the FDMC model to replace and downscale the response of the PF model. The combined agility and accuracy of the hybrid FDMC-ML model enables part-scale microstructure predictions that can be further used for property predictions to accelerate AM process optimization.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Terahertz-polarizing effect based on geometric anisotropy of Ti 3 C 2 T x MXene nanosheets

Two-dimensional (2D) nanomaterials have garnered considerable attention due to their unique properties, such as thinness and excellent electronic properties. The inherent anisotropy of 2D nanomaterials, which is characterized by their high aspect ratio, can maximize the directional functionality to enhance the conductivity and utilization of edges. Here, we demonstrate how to utilize the edges of titanium carbide (Ti 3 C 2 T x ) MXene nanosheet to control the linear polarization in the terahertz (THz) frequency range. By a simple and unique vertical alignment exploiting the high surface charge and excellent colloidal dispersibility of MXene nanosheets, MXene nanosheets are vertically oriented along an applied AC electric field. The well-aligned edges justify the THz polarizing effect, revealing outstanding performances such as the broadband coverage in 0.2–1.5 THz and an exceptional extinction ratio reaching 20 dB. Furthermore, we vary the local orientation of the vertical MXene nanosheets by tailoring the applied electric field, enabling spatially controllable polarization capabilities. Our results can provide a generic tool for the utilization of 2D nanomaterials in diverse potential applications in optics and electronics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Mechanistic understanding of aging behaviors of critical-material-free Li 4 Ti 5 O 12 //LiNi 0.9 Mn 0.1 O 2 cells with fluorinated carbonate-based electrolytes for safe energy storage with ultra-long life span

Behind-the-meter storage (BTMS) systems - a viable method to minimize potential risk of blackout events and stabilize the grid - require a different type of cost-effective energy storage with excellent safety, ultra-long (>20 years) cycle life and reasonable energy density compared that of electric vehicles. To increase the energy density and reduce the cost of a long-term cyclable lithium-titanate-based cell, it is required to employ a critical-material-free high voltage cathode and an electrolyte with good electrochemical and transport properties. In this report the long-term electrochemical performance and behaviors of selected critical-material-free Li 4 Ti 5 O 12 (LTO)//LiNi 0.9 Mn 0.1 O 2 (LNMO) full cells for BTMS applications are evaluated and analyzed in the optimized voltage range of 1.4-2.7 V at 45 degrees C with different fluorinated carbonate-based electrolytes. The fluoroethylene carbonate (FEC)-based electrolyte cell shows the highest capacity retention of 57.9% and Coulombic efficiency (CE) of 99.96% after 1000 cycles, potentially attributed to a dense, homogenous and less resistive LiF-rich solid-electrolyte interphase (SEI) layer formed on the surface of LTO that may mitigate electrolyte decomposition and maintain relatively low cell impedance during cycling. The 3,3,3-fluoroethylmethyl carbonate (F-EMC)-based electrolyte cell, however, presents the worst performance with lower capacity and a sharp decrease of CE, due to unstable and non-uniform SEI formation and continuous oxidative electrolyte decomposition. This mechanistic understanding of cell aging behaviors and failure mechanisms with detailed analysis of surface chemistry and electrode morphology can guide design of new electrode chemistries and electrolyte formulations for the development of BTMS batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Structural origin of size effect on piezoelectric performance of Pb(Zr,Ti)O 3

Grain size effect plays a vital role in piezoelectric performance from both scientific and technological view. However, the underlying structural mechanism related to grain size is still unclear. In the present study, the structural mechanism of grain size effect on piezoelectric performance has been revealed in the prototype Pb(Zr, Ti)O 3 system by using in-situ synchrotron X-ray diffraction. The miniaturization of grain size tends to favor the appearance of higher symmetric tetragonal phase, while a single monoclinic phase is determined in the coarse-grained ceramics. The direct structural evidence reveals that both tetragonal and monoclinic phases in the fine-grained ceramics are less sensitive to the electric field, corresponding to the inferior piezoelectric performance, while the single monoclinic phase in the coarse-grained ceramics is more active to be driven by the electric field, generating good piezoelectric behavior. Both domain switching ability and lattice strain are suppressed with decreasing grain size, which directly leads to the deterioration in piezoelectric performance. In conclusion, the current results will benefit the structural understanding of the size effect of piezoelectric and other related systems.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Solid-state transformations during laser directed energy deposition of Ti-6Al-4V powder hydride-dehydrided from scrap metals

During laser directed energy deposition (DED-LB), thermal cycling and powder chemical composition produce distinct thermal histories, which vary mechanical properties. Using real-time X-ray diffraction, this study investigates solid-state transformations during DED-LB to understand process-structure-property relationships for angular Ti-6Al-4V powder hydride–dehydrided from scrap metals. Results showed that regions near the molten pool experienced high cooling rates, leading to martensitic transformation from the β phase and increased hardness. Regions farther from the molten pool underwent tempering without solid-state transformation and decreased hardness. These findings support alternative feedstocks for metal additive manufacturing for a circular economy and resilient supply chains.

Additive manufacturing (AM)↗
DOE OSTI2024

Automated path planning for functionally graded materials considering phase stability and solidification behavior: Application to the Mo-Nb-Ta-Ti system

Functionally graded materials have the potential to improve upon monolithic parts by locally tailoring compositions to surrounding environmental conditions. Difficulties arise when designing composition gradients as incompatible materials can result in detrimental phase formation and failure of the gradient joint. As many alloys are multi-component, designing a composition gradient free of detrimental phases is difficult due to the large composition space available to explore. A framework was developed that improves the path planning algorithm and surrogate models with adaptive sampling schemes specific to their problem definition. A cost function was created to minimize a property (such as cracking susceptibility) along a path. This framework was applied to the Mo-Nb-Ta-Ti system as a case study to showcase the efficiency in building the surrogate models and in iterating different optimal compositionally graded paths.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Long-term cyclability of Li 4 Ti 5 O 12 /LiMn 2 O 4 cells using carbonate-based electrolytes for behind-the-meter storage applications

Li 4 Ti 5 O 12 /LiMn 2 O 4 (LTO/LMO) chemistry was evaluated as a potential candidate for behind-the-meter storage (BTMS) applications. Its long-term cycle performance at 45 °C was tested using ethylene carbonate (EC) and propylene carbonate (PC) solvent electrolytes. Over 1000 cycles, LTO/LMO cells exhibited ~80% capacity retention and Coulombic efficiency higher than 99.96%. Electrochemical test results showed the major degradation mode of LTO/LMO cells arises from continuous electrolyte decomposition at the LTO anode and loss of Li inventory. EC and PC electrolytes created distinct surface layers, where the EC reduction products were more effective in passivating the LTO electrode surface. Dissolution and migration of Mn from the cathode was probed as Mn 2+ species distributed throughout the surface layer at the anode. By utilizing a prelithiated LTO electrode, the LTO/LMO cell performance was significantly enhanced with EC electrolyte. On the other hand, PC electrolyte resulted in accelerated electrolyte decomposition at the lithiated LTO surface due to the lack of surface passivation. Thus, mitigating parasitic reactions at the LTO electrode is the key to developing successful LTO/LMO cells.

25 ENERGY STORAGE↗
DOE OSTI2020

Small fatigue crack growth behavior of Ti-6Al-4V produced via selective laser melting: In situ characterization of a 3D crack tip interactions with defects

Small fatigue crack growth (SFCG) behavior is examined for additively manufactured Ti-6Al-4V specimens with optimal and trial build conditions (representing an increased degree of defects) through a combination of in situ tomography and in situ energy dispersive X-ray diffraction. The results showed slower crack growth rates for the SFCG samples compared to the long cracks (which was not expected). Finally, in the case of the trial conditions, the increased levels of porosity deterred crack growth by blunting the crack, as evident by the in situ tomography characterization.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Grain reorientation and stress-state evolution during cyclic loading of an α -Ti alloy below the elastic limit

Here, high-energy synchrotron x-rays are used to track grain-averaged lattice reorientation and stress-state evolution in Ti–7Al as it is cyclically loaded to 90% of its macroscopic yield stress. This evolution provides clear indication of accumulating plastic strain even though the sample never exceeded the elastic limit. The largest changes in lattice orientation and stress state are observed following the first cycle then evolution continues at a lower rate with subsequent cycles. Variation of the axes about which lattice reorientation occurs is found to be highly dependent on the maximum resolved shear stress and corresponding activation of various families of slip systems.

36 MATERIALS SCIENCE↗
DOE OSTI2026

High-throughput oxidation screening and down-selection of refractory high entropy alloys in the Al-Cr-Mo-Nb-Ta-Ti system

Rapid experimentation and characterization are ever-present needs in the discovery of high entropy alloys. High entropy alloy systems are difficult to survey with systematic composition sweeps using traditional synthesis methods. The number of distinct compositions in even a four-element system is experimentally intractable. Exploration of these, and higher-element systems, necessitates thermodynamic prediction coupled with an automated sample creation method and a rapid screening methodology to effectively down-select alloys with targeted properties. As a result, a high-throughput method for evaluating the oxidation performance of refractory high entropy alloys was developed and tested. The six-element system of aluminum, chromium, molybdenum, niobium, tantalum, and titanium was evaluated for single phase stability and short-duration oxidation resistance. Target compositions were initially determined via thermodynamic predictions of single-phase stability across a wide temperature range. A twenty-five-sample build plate was produced using directed energy deposition additive manufacturing. After fabrication, the twenty-five 1 cm 3 samples were heat treated and characterized for composition and phase identification. The build plate was exposed to a high temperature oxidizing environment at 1000 °C for three hours. After oxidation, the composition, morphology, and chemistry of the oxides formed were characterized. Of the twenty-five samples produced, nine exhibited a favorable oxidation response, from which a single-phase BCC alloy at a composition of Al 13 Cr 7 Mo 19 Nb 18 Ta 26 Ti 17 was identified as the alloy with the most protective oxidation coating with a thin, adherent oxide scale. Finally, the complete experimental down-selection—from machine setup to final alloy identification—required approximately 45 labor hours, demonstrating a rapid validation for alloy discovery.

Additive manufacturing↗
DOE OSTI2021

Optimization of the microstructure and mechanical properties of electron beam welded high-strength medium-entropy alloy (NiCoCr) 94 Al 3 Ti 3

For this work, the weldability and effects of subsequent heat treatment on the microstructure and mechanical properties of the medium-entropy alloy (MEA) (NiCoCr) 94 Al 3 Ti 3 have been explored using electron beam welding (EBW). It was found that EBW joints consist of a supersaturated f.c.c. matrix with coarse, asymmetric columnar grains (17.7–24 μm). The fraction of twins and Σ3 n CSL boundaries in weld joints was only 10% of that in the base metal, a value which increased to 30% after aging at 800 °C. The aging also led to improvements in the hardness, tensile strength, and work hardening rate, a result of the precipitation of a high volume fraction (0.29–0.33) of ultrafine (15–17.4 nm dia.) coherent spherical L1 2 -structured particles. The contributions of the L1 2 nanoparticles and Hall-Petch strengthening to the yield strength were estimated to be 537–573 MPa and 105–123 MPa, respectively. The MEA shows excellent weldability and, after aging, good strength (YS~1098 MPa, UTS~1368 MPa) and elongation to failure (~11%) by ductile fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The effect of 10 at.% Al addition on the hydrogen storage properties of the Ti 0.33 V 0.33 Nb 0.33 multi-principal element alloy

We report here a thorough study on the effect of 10 at.% Al addition into the ternary equimolar Ti 0.33 V 0.33 Nb 0.33 alloy on the hydrogen storage properties. Despite a decrease of the storage capacity by 20%, several other properties are enhanced by the presence of Al. The hydride formation is destabilized in the quaternary alloy as compared to the pristine ternary composition, as also confirmed by machine learning approach. The hydrogen desorption occurs at lower temperature in the Al-containing alloy relative to the initial material. Moreover, the Al presence improves the stability during hydrogen absorption/desorption cycling without significant loss of the capacity and phase segregation. Finally, this study proves that Al addition into multi-principal element alloys is a promising strategy for the design of novel materials for hydrogen storage.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Interfacial antiferromagnetic phase induced two-step magnetization reversal in PbZr 0.52 Ti 0.48 O3/La 0.67 Sr 0.33 MnO 3 superlattices

Artificial multiferroic heterostructures have recently attracted much interests due to the demonstrated magnetoelectric coupling (MEC) and unique functionalities, promising a tantalizing perspective of novel applications in next-generation electronic, memory, sensor, and energy harvesting technologies. Herein, we report a two-step magnetization reversal in PbZr 0.52 Ti 0.48 O 3 /La 0.67 Sr 0.33 MnO 3 (PZT/LSMO) superlattices, which originates from the strongly entangled strain-, ferroelectric (FE)-polarization-, and exchange-dependent effects. Specifically, the preferential occupancy of the in-plane Mn d x 2 -y 2 orbitals is triggered via the collective effects of the large tensile strain and FE polarization, giving rise to an interfacial antiferromagnetic (AFM) layer with strong AFM anisotropy. The strong spin exchange coupling between the AFM layer and the adjacent ferromagnetic (FM) layer facilitates the magnetic stratification of the FM layer, leading to two coercivities, i.e., two-step magnetization reversal. Meanwhile, a sizeable exchange bias (EB) field is induced. The emerged two-step magnetization reversal concomitant with the pronounced EB phenomenon should be a signature of an enhanced MEC in PZT/LSMO superlattices. Finally, our results will stimulate further interests in multiferroic superlattices in applications of multiferroic-based devices.

36 MATERIALS SCIENCE↗