SEARCH · Engineering Papers

Results for “Shock wave experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

All sources NASA NTRS DOE OSTI

DOE OSTI2019

A study of velocity, temperature, and density in the plasma generated by laser-induced breakdowns

The paper presents velocity measurements of shock-induced flow field, leading to vortex generation and plasma deformation in air. Femtosecond-laser electronic excitation tagging (FLEET) velocimetry was performed at the times Δt = 3, 20, 50, and 100 µs post laser-induced breakdown. Emissions over Δt = 3–10 µs showed the propagations of the initially elliptic shock, transitioning into a spherical front. The shock emanated along the laser axis causes the flow outward, and then the pressure gradient generated by the rarefaction wave drives the inward flow at later moments, with the velocity magnitude approaching a steady-state value of 40 m s -1 . Temporal velocity evolution was compared with non-self-similar solutions behind the propagating shock, which are sensitive to the size of the energy deposition, and the use of the measured initial plasma diameter reproduced the experiment. There establishes a region of uniform velocity around 35 m s -1 in the air-flow running through the plasma, which triggers the roll-up of the plasma surface by a large-scale vortex, providing the detail of flow field evolution from the shock propagation to the plasma deformation. A collective Thomson scattering and hybrid fs/ps pure rotational coherent anti-Stokes Raman scattering (CARS) were also performed to gain insight into the high-temperature plasma. An effective electron–ion recombination rate of 2 x 10 -12 cm 3 s -1 was measured at Δt = 0.5–10 µs, during a dynamic plasma expansion and compression. When the shock resides close to the plasma at Δt = 0.5–1 µs, the temperature distributions were found to follow the similarity law.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1991

One- and three-dimensional impact-induced tensional failure in rock

Planar impact (10 to 25 m/sec) experiments were employed to induce dynamic tensile failure in Bedford limestone for stress durations of 0.5 and 1.3 microsec. Ultrasonic P- and S-wave velocities of recovered targets demonstrate deficits caused by microcracks at tensile stresses greater than 35 and 60 MPa in 1.3 and 0.5 microsec experiments. Three-dimensional impact experiments on 20 cm-sized blocks of Bedford limestone and San Marcos gabbro demonstrate compressional wave velocity deficits up to 30 percent in the vicinity of the crater. The damage microcrack decreases as r exp -1.56 from the crater, indicating a dependence on the magnitude and duration of the tensile hoop stresses associated with the impact-induced shock wave.

Ahrens, Thomas J.↗

NASA NTRS2011

The 2011 February 15 Coronal Mass Ejection: Reconciling SOHO and STEREO Observations in Quadrature

The Large-Angle and Spectrometric Coronagraph (LASCO) on board SOHO observed a fast halo coronal mass ejection on 2011 February 15. The STEREO spacecraft were in quadrature with SOHO (STEREO-A ahead of Earth by 87 degrees and STEREO-B 94 degrees behind Earth), enabling CME measurement using the three spacecraft. The sky-plane speed measured by SOHO/LASCO is closely related to the expansion speed of the CME, while the radial speed was measured by STEREO-A and STEREO-B. In addition, STEREO-A and STEREO-B images measured the width of the CME, which is unknown from Earth view. From the SOHO and STEREO measurements, we confirm the relationship between the expansion speed (V(sub exp) ) and radial speed (V(sub rad)) derived previously from geometrical considerations (Gopalswamy et al. 2009): = V(sub rad) = 1/2 (1 + cot w) V(sub exp), where w is the half width of the CME. We can also measure the Earthward speed of the CME directly from the STEREO measurements. The travel time to Earth predicted from the Earthward speed using the Empirical Shock Arrival model is approximately 12 hours shorter than the actual travel time obtained from in situ measurements at Ll. The primary reason for this discrepancy seems to be the interaction with the two preceding CMEs that slowed down the CME in question. The CME interaction is also confirmed from the radio enhancement observed by Wind/WAVES and STEREO WAVES experiments.

Gopalswamy, Natchimuthuk↗

DOE OSTI2022

Turbulence generation by shock interaction with a highly nonuniform medium

An initially planar shock wave propagating into a medium of nonuniform density will be perturbed, leading to the generation of postshock velocity perturbations. Using numerical simulations we study this phenomenon in the case of highly nonuniform density (order-unity normalized variance, $\sigma_\rho/\bar{\rho}\sim1$) and strong shocks (shock Mach numbers $\bar{M}_s\gtrsim10$). This leads to a highly disrupted shock and a turbulent postshock flow. We simulate this interaction for a range of shock drives and initial density configurations meant to mimic those which might be presently achieved in experiments. Theoretical considerations lead to scaling relations, which are found to reasonably predict the postshock turbulence properties. The turbulent velocity dispersion and turbulent Mach number are found to depend on the preshock density dispersion and shock speed in a manner consistent with the linear Richtymer-Meshkov instability prediction. We also show a dependence of the turbulence generation on the scale of density perturbations. The postshock pressure and density, which can be substantially reduced relative to the unperturbed case, are found to be reasonably predicted by a simplified analysis that treats the extended shock transition region as a single normal shock.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

X-ray diffraction measurements and pressure determination in nanosecond compression of solids up to 600 GPa

X-ray diffraction measurements under laser-driven dynamic compression now allow us to investigate the atomic structure of matter at TPa pressures and thousands of degree temperatures with broad implications for condensed matter physics, planetary science and astronomy. Furthermore, pressure determination in these experiments often relies on velocimetry measurements coupled with modeling that requires accurate knowledge of the optical and thermo-mechanical properties of a window material, resulting in significant systematic uncertainty. Here we demonstrate different approach applicable to X-ray diffraction experiments under quasi-isentropic ramp-compression based on the use of in-situ pressure calibrants, similar to the methods often adopted in static-compression experiments with diamond anvil cells. Focusing on experiments using a diamond window, we discuss challenges and mitigation strategies for the novel approach. Our study, in addition to providing new structural information of 5 metals up to hundreds of GPa, provides validation to the currently used methods based on time-resolved measurement of the diamond free-surface velocity, and reveals that the use of in-situ calibrants enables a factor of four reduction in the pressure uncertainty in these experiments.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS1995

Laser Light Scattering by Shock Waves

Scattering of coherent light as it propagates parallel to a shock wave, formed in front of a bluff cylindrical body placed in a supersonic stream, is studied experimentally and numerically. Two incident optical fields are considered. First, a large diameter collimated beam is allowed to pass through the shock containing flow. The light intensity distribution in the resultant shadowgraph image, measured by a low light CCD camera, shows well-defined fringes upstream and downstream of the shadow cast by the shock. In the second situation, a narrow laser beam is brought to a grazing incidence on the shock and the scattered light, which appears as a diverging sheet from the point of interaction, is visualized and measured on a screen placed normal to the laser path. Experiments are conducted on shocks formed at various free-stream Mach numbers, M, and total pressures, P(sub 0). It is found that the widths of the shock shadows in a shadowgraph image become independent of M and P(sub 0) when plotted against the jump in the refractive index, (Delta)n, created across the shock. The total scattered light measured from the narrow laser beam and shock interaction also follows the same trend. In the numerical part of the study, the shock is assumed to be a 'phase object', which introduces phase difference between the upstream and downstream propagating parts of the light disturbances. For a given shape and (Delta)n of the bow shock the phase and amplitude modulations are first calculated by ray tracing. The wave front is then propagated to the screen using the Fresnet diffraction equation. The calculated intensity distribution, for both of the incident optical fields, shows good agreement with the experimental data.

Panda, J.↗

DOE OSTI2024

Stress field measurements using quantitative schlieren

Quantitative schlieren analysis is extended here to optically transparent solids in quasi-static and dynamic experiments to measure stress distributions. The quasi-static experiments in polymethyl methacrylate (PMMA) compared refraction angles and stress gradients calculated from schlieren images to the analytical Flamant solution of a line load on a half-space. The quantitative schlieren measurements of the stress field in the thin sample with a load compared well to the analytical solution. The analysis method was then extended to explosive induced shock waves in PMMA. The explosive induced response of PMMA was experimentally studied using high-speed schlieren to visualize the shock propagation in conjunction with Photon Doppler Velocimetry (PDV) to record surface velocity histories. The stress state estimated from the schlieren images was compared to the stress calculated from the PDV measurements. High-speed imaging limitations caused the shock wave to not be fully resolved in the images, but was resolved in the PDV measurement. The stress state behind the shock calculated from the high-speed images followed a similar trend to the stress calculated from the PDV measurements.

Physics↗

NASA NTRS1974

Pioneer 10 observations of the solar wind interaction with Jupiter

Detailed analysis of the Pioneer 10 plasma analyzer experiment flight data during the Jupiter flyby in late November and early December 1973 has been performed. The observations show that the interaction of Jupiter's magnetic field with the solar wind is similar in many ways to that at earth, but the scale size is over 100 times larger. Jupiter is found to have a detached standing bow shock wave of high Alfven Mach number. Like the earth, Jupiter has a prominent magnetopause that deflects the magnetosheath plasma and excludes its direct entry into the Jovian magnetosphere. Unlike that of the earth, the sunward hemisphere of Jupiter's outer magnetosphere is found to be highly inflated with thermal plasma and a high-beta region that is highly responsive to changes in solar wind dynamic pressure.

Wolfe, J. H.↗

NASA NTRS1985

Hybrid approach to steady transonic normal shock-compressible laminar boundary layer interactions over airfoils with suction

Transonic airfoil flow is to a large degree affected by viscous-inviscid interactions. Among them a key role is played by the boundary layer interaction with the shock wave embedded in the flow field and the interaction of the boundary layer with the sustained adverse pressure gradients. The effects of these interactions can be controlled or suppressed by introducing surface mass transfer such as suction. This investigation deals strictly with the study of shock-laminar boundary layer interactions including distributed mass transfer. The present calculations agree with experiments on a swept LFC wing at low speeds which indicates that with a suitable choice of the extent of the airfoil surface over which suction is applied and adjustment of the suction velocity, full-chord laminar flow can be maintained and separation can be prevented completely.

Ram, R. B.↗

NASA NTRS1986

First results from the Giotto magnetometer experiment at comet Halley

The Giotto magnetometer experiment at comet Halley has for the first time provided magnetic field measurements in all the important spatial regions characterizing the front-side interaction between the solar-wind magnetoplasma and a cometary atmosphere. Upstream waves of cometary origin have been observed at distances greater than two million km from the comet, both inbound and outbound. A cometary bow shock has been identified at 1.15 million inbound on the dawn side and a thick quasi-parallel cometary bow shock outbound. A turbulent magnetosheath has been observed further inside. A magnetic pile-up region has been identified inside 135,000 km, inbound, and 263,000 km, outbound, with fields up to 57 and 65 nT, respectively. A cavity region with essentially zero magnetic field has been discovered, with a width of 8500 km along the trajectory around closest approach.

Neubauer, F. M.↗

NASA NTRS1989

A numerical analysis of the British Experimental Rotor Program blade

Two Computational Fluid Dynamic codes which solve the compressible full-potential and the Reynolds-Averaged Thin-Layer Navier-Stokes equations were used to analyze the nonrotating aerodynamic characteristics of the British Experimental Rotor Program (BERP) helicopter blade at three flow regimes: low angle of attack, high angle of attack and transonic. Excellent agreement was found between the numerical results and experiment. In the low angle of attack regime, the BERP had less induced drag than a comparable aspect ratio rectangular planform wing. At high angle of attack, the blade attained high-lift by maintaining attached flow at the outermost spanwise locations. In the transonic regime, the BERP design reduces the shock strength at the outer spanwise locations which affects wave drag and shock-induced separation. Overall, the BERP blade exhibited many favorable aerodynamic characteristics in comparison to conventional helicopter rotor blades.

Duque, Earl P. N.↗

NASA NTRS1999

"Driverless" Shocks in the Interplanetary Medium

Many interplanetary shocks have been detected without an obvious driver behind them. These shocks have been thought to be either blast waves from solar flares or shocks due to sudden increase in solar wind speed caused by interactions between large scale open and closed field lines of the Sun. We investigated this problem using a set of interplanetary shock detected {\it in situ} by the Wind space craft and tracing their solar origins using low frequency radio data obtained by the Wind/WAVES experiment. For each of these "driverless shocks" we could find a unique coronal mass ejections (CME) event observed by the SOHO (Solar and Heliospheric Observatory) coronagraphs. We also found that these CMEs were ejected at large angles from the Sun-Earth line. It appears that the "driverless shocks" are actually driver shocks, but the drivers were not intercepted by the spacecraft. We conclude that the interplanetary shocks are much more extended than the driving CMEs.

Gopalswamy, N.↗

NASA NTRS1973

Solar flare produced pulsations in meter and X-ray wavelengths

The mechanism responsible for the modulation of synchrotron radiation in the meter wave range by a solar flare is examined. The proposed explanation is based on the interaction of a flare generated shock front with a magnetic flux tube extending out into the corona over the flare. As the shock wave propagates through the flux tube, Alfven waves are developing and travelling up the tube toward each other, thereby accelerating electrons and protons by the Fermi mechanism and thus filling the top of the flux tube with energetic electrons. Radial oscillations develop as the shock front becomes parallel to the magnetic field direction and the intensity of the synchrotron radiation is modulated by these oscillations. An OSO-5 experiment detected a hard X-ray burst associated with the flare that produced modulated radio emission and X-ray modulations that are attributed to density fluctuations in the X-ray bursts.

Frost, K. J.↗

NASA NTRS1974

Magnetic field observations near Venus - Preliminary results from Mariner 10

The NASA-GSFC magnetic field experiment on Mariner 10 is the first flight of a dual magnetometer system conceived to permit accurate measurements of weak magnetic fields in space in the presence of a significant and variable spacecraft magnetic field. Results from a preliminary analysis of a limited data set are summarized in this report, which is restricted primarily to Venus encounter. A detached bow shock wave that develops as the super Alfvenic solar wind interacts with the Venusian atmosphere has been observed. However, the unique coincidence of trajectory position and interplanetary field orientation at the time of bow shock crossing led to a very disturbed shock profile with considerably enhanced upstream magnetic fluctuations. At present it is not possible to ascertain the nature and characteristics of the obstacle responsible for deflecting the solar wind flow. Far downstream disturbances associated with the solar wind wake have been observed.

Ness, N. F.↗

NASA NTRS2008

Computational Analyses in Support of Sub-scale Diffuser Testing for the A-3 Facility: Unsteady Analyses and Risk Assessment - Part 2

Simulation technology can play an important role in rocket engine test facility design and development by assessing risks, providing analysis of dynamic pressure and thermal loads, identifying failure modes and predicting anomalous behavior of critical systems. This is especially true for facilities such as the proposed A-3 facility at NASA SSC because of a challenging operating envelope linked to variable throttle conditions at relatively low chamber pressures. Design Support of the feasibility of operating conditions and procedures is critical in such cases due to the possibility of startup/shutdown transients, moving shock structures, unsteady shock-boundary layer interactions and engine and diffuser unstart modes that can result in catastrophic failure. Analyses of such systems is difficult due to resolution requirements needed to accurately capture moving shock structures, shock-boundary layer interactions, two-phase flow regimes and engine unstart modes. In a companion paper, we will demonstrate with the use of CFD, steady analyses advanced capability to evaluate supersonic diffuser and steam ejector performance in the sub-scale A-3 facility. In this paper we will address transient issues with the operation of the facility especially at startup and shutdown, and assess risks related to afterburning due to the interaction of a fuel rich plume with oxygen that is a by-product of the steam ejectors. The primary areas that will be addressed in this paper are: (1) analyses of unstart modes due to flow transients especially during startup/ignition, (2) engine safety during the shutdown process (3) interaction of steam ejectors with the primary plume i.e. flow transients as well as probability of afterburning. In this abstract we discuss unsteady analyses of the engine shutdown process. However, the final paper will include analyses of a staged startup, drawdown of the engine test cell pressure, and risk assessment of potential afterburning in the facility. Unsteady simulations have been carried out to study the engine shutdown process in the facility and understand the physics behind the interactions between the steam ejectors, the test cell and the supersonic diffuser. As a first approximation, to understand the dominant unsteady mechanisms in the engine test cell and the supersonic diffuser, the turning duct in the facility was removed. As the engine loses power a rarefaction wave travels downstream that disrupts the shock cell structure in the supersonic diffuser. Flow from the test cell is seen to expand into the supersonic diffuser section and re-pressurizes the area around the nozzle along with a upstream traveling compression wave that emanates from near the first stage ejectors. Flow from the first stage ejector expands to the center of the duct and a new shock train is formed between the first and second stage ejectors. Both stage ejectors keep the facility pressurized and prevent any large amplitude pressure fluctuations from affecting the engine nozzle. The resultant pressure loads the nozzle experiences in the shutdown process are small.

Ahuja, Vineet↗

NASA NTRS2021

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Boundary layer transition↗

NASA NTRS1991

Hypersonic Research Vehicle (HRV) real-time flight test support feasibility and requirements study. Part 1: Real-time flight experiment support

The results are presented of a study to identify potential real time remote computational applications to support monitoring HRV flight test experiments along with definitions of preliminary requirements. A major expansion of the support capability available at Ames-Dryden was considered. The focus is on the use of extensive computation and data bases together with real time flight data to generate and present high level information to those monitoring the flight. Six examples were considered: (1) boundary layer transition location; (2) shock wave position estimation; (3) performance estimation; (4) surface temperature estimation; (5) critical structural stress estimation; and (6) stability estimation.

Rediess, Herman A.↗

DOE OSTI2020

Strength of porous α-SiO 2 in a shock loaded environment: Calibration via Richtmyer–Meshkov instability and validation via Mach lens

The strength of brittle porous media is of concern in numerous applications, for example, earth penetration, crater formation, and blast loading. Thus, it is of importance to possess techniques that allow for constitutive model calibration within the laboratory setting. The goal of the current work is to demonstrate an experimental technique allowing for strength assessment of porous media subjected to shock loading, which can be implemented into pressure-dependent yield surfaces within numerical simulation schemes. As a case study, the deviatoric response of distended α-SiO 2 has been captured in a tamped Richtmyer–Meshkov instability (RMI) environment at a pressure regime of 4–10 GPa. Hydrocode simulations were used to interpret RMI experimental data, and a resulting pressure-dependent yield surface akin to the often employed modified Drucker–Prager model was calibrated. Simulations indicate that the resulting jet length generated by the RMI is sensitive to the porous media strength, thereby providing a feasible experimental platform capable of capturing the pressurized granular deviatoric response. Furthermore, in efforts to validate the RMI-calibrated strength model, a set of Mach-lens experiments was performed and simulated with the calibrated pressure-dependent yield surface. Excellent agreement between the resulting Mach-lens length in experiment and simulation provides additional confidence to the RMI yield-surface calibration scheme.

36 MATERIALS SCIENCE↗