Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Physical and optoelectronic characterization of reactively sputtered molybdenum-silicon-nitride alloy metal gate electrodes

With continued transistor scaling, work function tuning of metal gates has become important for advanced complementary-metal-oxide-silicon applications. The work function tuning of reactively sputtered Mo{sub x}Si{sub y}N{sub z} (also referred to as MoSiN) gates has been studied through the incorporation of nitrogen. The nitrogen concentration in the MoSiN films was altered by controlling the gas flow ratio, R{sub N}=N{sub 2}/(N{sub 2}+Ar), during gate deposition. The sheet resistance (R{sub s}) of blanket MoSiN films, measured using four-point resistance method, was found to increase as the gas flow ratio was varied from 10% to 40%. Current-voltage measurements confirmed excellent electrical stability of MoSiN/SiO{sub 2}/p-Si gate stack for applied electric fields ranging up to 6 MV/cm. High frequency capacitance-voltage measurements were used to extract the MoSiN work function ({phi}{sub m}) using the relationship between the flatband voltage (V{sub FB}) and the oxide thickness (t{sub ox}). The extracted MoSiN/SiO{sub 2} interfacial barrier heights, obtained through the internal photoemission of electrons, were used to corroborate the extracted values of MoSiN work function. The MoSiN work functions ({phi}{sub m}), extracted independently using both techniques, were consistent and were observed to decrease with increasing gas flow ratio [N{sub 2}/(N{sub 2}+Ar)]. Secondary ion mass spectrometry depth analysis revealed uniform distribution of nitrogen throughout the bulk MoSiN films, with no piling up at gate-dielectric interface. X-ray photoelectron spectroscopy surface analysis suggested a steady increase in the Mo-N bonds, and therefore the total nitrogen concentration (from {approx}20% to 32%), as the gas flow ratio is increased from 10% to 40%. A similar trend was observed in the nitrogen concentration (in percent), measured using Rutherford backscattering spectroscopy, for these gate deposition conditions. These material characterization results demonstrate that the increase in nitrogen concentration in MoSiN films is consistent with the lowering of MoSiN work function. Moreover, the work function of reactively sputtered Mo{sub x}Si{sub y}N{sub z} films was found to be variable over {approx}0.3 eV by adjusting the nitrogen concentration.

36 MATERIALS SCIENCE↗

Determination of composition in stoichiometric Co-N ultrathin films by nitrogen plasma sputtering

This work utilizes low-energy sputtering to incorporate the generated nitrogen plasma into an epitaxial 1.4 nm Co film on the surface of a ZnO(002) substrate. In this method, ultrathin Co-N amorphous films were formed. Interestingly, Co is key to the formation of Co-N films. Without the deposition of Co on the ZnO(002), nitride films cannot be formed. Observations of the surface composition of the Co-N films after the firing of a N{sup +} ion beam onto it demonstrated that the surface concentration of Co reduced at the same rate as the reduction in the concentration of N upon successive sputtering. Theoretical calculations based on the Auger peak-to-peak amplitudes established that the composition of the amorphous Co-N thin films may be Co{sub 3}N{sub 2}.

36 MATERIALS SCIENCE↗

High Temperature Thermal Stability and Oxidation Resistance of Magnetron-sputtered Homogeneous CrAlON Coatings on 430 Steel

The requirements of low cost and high-temperature corrosion resistance for bipolar interconnect plates in solid oxide fuel cell stacks has directed attention to the use of metal plates with oxidation resistant coatings. We have investigated the performance of steel plates with homogenous coatings of CrAlON (oxynitrides). The coatings were deposited using RF magnetron sputtering, with Ar as a sputtering gas. Oxygen in these coatings was not intentionally added. Oxygen might have come through contaminated nitrogen gas bottle, leak in the chamber or from the partial pressure of water vapors. Nitrogen was added during the growth process to get oxynitride coating. The Cr/Al composition ratio in the coatings was varied in a combinatorial approach. The coatings were subsequently annealed in air for up to 25 hours at 800 deg. C. The composition of the coated plates and the rate of oxidation were characterized using Rutherford backscattering (RBS) and nuclear reaction analysis (NRA). From our results, we conclude that Al rich coatings are more susceptible to oxidation than Cr rich coatings.

36 MATERIALS SCIENCE↗

Trapping characteristics of Al{sub 2}O{sub 3}/HfO{sub 2}/SiO{sub 2} stack structure prepared by low temperature in situ oxidation in dc sputtering

In this work, a dielectric stack with Al{sub 2}O{sub 3}/HfO{sub 2}/SiO{sub 2} (1.8 nm/1.6 nm/2.5 nm) trilayer structure prepared by low temperature in situ natural oxidation during dc sputtering is investigated. We study the electrical characteristics, including the dielectric leakage of 10{sup -8} A/cm{sup 2} at V{sub g}=-2 V, the current transport mechanism and trap distributions through the trilayer dielectric stack. The Fowler-Nordheim barrier height of the prepared Al{sub 2}O{sub 3}(phi{sub FN,Al{sub 2O{sub 3}}}) was extracted as 3.06+-0.15 eV. The current variation ratios [DELTAJ{sub g}/J{sub g}(0)] during constant voltage stressing were found to decrease with raising gate stress voltages for the trilayer stack in comparison with that [DELTAJ{sub g}/J{sub g}(0)] increase with raising gate stress voltages for the two-layer HfO{sub 2}/SiO{sub 2} stack. Shallow traps located in HfO{sub 2} were supposed to be major trapping centers within the trilayer stack. The proposed method of in situ oxidation during dc sputtering is of merit and low in process temperature. The trilayer dielectric stacks are an alternative option for nonvolatile memory application, especially under the consideration of low temperature limitation.

36 MATERIALS SCIENCE↗

Low temperature charge carrier hopping transport mechanism in vanadium oxide thin films grown using pulsed dc sputtering

Low temperature charge transport in vanadium oxide (VO{sub x}) thin films processed using pulsed dc sputtering is investigated to understand the correlation between the processing conditions and electrical properties. It is identified that the temperature dependent resistivity {rho}(T) of the VO{sub x} thin films is dominated by a Efros-Shklovskii variable range hopping mechanism [Efros and Shklovskii, J. Phys. C 8, L49 (1975)]. A detailed analysis in terms of charge hopping parameters in the low temperature regime is used to correlate film properties with the pulsed dc sputtering conditions.

36 MATERIALS SCIENCE↗

Crystallization of sputtered-deposited and ion implanted amorphous Ge{sub 2}Sb{sub 2}Te{sub 5} thin films

X-ray diffraction and transmission electron microscopy have been utilized to measure the ion irradiation-induced modification in amorphous Ge{sub 2}Sb{sub 2}Te{sub 5} thin films. The isothermal crystallization of sputtered-deposited and Sb{sup +} ion irradiated amorphous samples has been studied, focusing on the evolution of the microstructure during the initial stage of the transformation. In both samples, the amorphous to crystal transition occurs through the nucleation of face centered cubic (fcc) crystal domains at the film surface. A fast bidimensional growth of the crystalline nuclei in the sputtered-deposited films occurs by the generation of transrotational grains. The lattice parameter decreases as the crystalline fraction increases above 80%, and it approaches the fcc bulk value at the end of the transformation. Ion irradiation produces a densification of the deposited amorphous film (approx4% vertical shrinkage measured by atomic force microscopy) and an enhancement of the crystallization rate. Even in the irradiated amorphous, the nucleation occurs at the film surface and proceeds by the growth of the grains through the thickness of the layer although the density of the transrotational grains is strongly reduced with respect to the unirradiated amorphous. A link between the ion beam induced densification and the reduction of transrotational grains is proposed.

36 MATERIALS SCIENCE↗

Sputtering yields of Ru, Mo, and Si under low energy Ar{sup +} bombardment

Ion sputtering yields for Ru, Mo, and Si under Ar{sup +} ion bombardment in the near-threshold energy range have been studied using an in situ weight-loss method with a Kaufman ion source, Faraday cup, and quartz crystal microbalance. The results are compared to theoretical models. The accuracy of the in situ weight-loss method was verified by thickness-decrease measurements using grazing incidence x-ray reflectometry, and results from both methods are in good agreement. These results provide accurate data sets for theoretical modeling in the near-threshold sputter regime and are of relevance for (optical) surfaces exposed to plasmas, as, for instance, in extreme ultraviolet photolithography.

36 MATERIALS SCIENCE↗

On the electron energy in the high power impulse magnetron sputtering discharge

The temporal variation of the electron energy distribution function (EEDF) was measured with a Langmuir probe in a high power impulse magnetron sputtering (HiPIMS) discharge at 3 and 20 mTorr pressures. In the HiPIMS discharge a high power pulse is applied to a planar magnetron giving a high electron density and highly ionized sputtered vapor. The measured EEDF is Maxwellian-like during the pulse; it is broader for lower discharge pressure and it becomes narrower as the pulse progresses. This indicates that the plasma cools as the pulse progresses, probably due to high metal content of the discharge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Broad, intense, quiescent beam of singly charged metal ions obtained by extraction from self-sputtering plasma far above the runaway threshold

Dense metal plasmas obtained by self-sputtering far above the runway threshold are well suited to generate intense quiescent ion beams. The dilemma of high current density and charge state purity can be solved when using target materials of low surface binding energy by utilizing non-resonant exchange reactions before ion extraction. Space-charge-limited quiescent beams of Cu+, Zn+, and Bi+ with ~;;10 mA/cm2 have been obtained through multi-aperture gridded ion extraction up to 45 kV from self-sputtering plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Formation and characterization of perpendicular mode Si ripples by glancing angle O{sub 2}{sup +} sputtering at room temperature

Off-normal low energy ion beam sputtering of solid surfaces often leads to morphological instabilities resulting in the spontaneous formation of ripple structures in nanometer length scales. In the case of Si surfaces at ambient temperature, ripple formation is found to take place normally at lower incident angles with the wave vector parallel to the ion beam direction. The absence of ripple pattern on Si surface at larger angles is due to the dominance of ion beam polishing effect. We have shown that a gentle chemical roughening of the starting surface morphology can initiate ripple pattern under grazing incidence ion beam sputtering (theta>64 deg. with respect to the surface normal), where the ripple wave vector is perpendicular to the ion beam direction. The characteristics of the perpendicular mode ripples are studied as a function of pristine surface roughness (2-30 nm) and projectile fluence (5x10{sup 16}-1.5x10{sup 18} O atoms cm{sup -2}). The quality of the morphological structure is assessed from the analysis of ion induced topological defects.

36 MATERIALS SCIENCE↗

Modeling the flux of high energy negative ions during reactive magnetron sputtering

The negative ion flux during reactive sputtering from planar and rotating cylindrical magnetrons has been studied. Energy resolved mass spectrometry was used to measure the energy and mass distribution of the negative ions. Also the angular distribution of the high energy ions was characterized for planar as well as for rotating cylindrical magnetrons. Besides these measurements, a binary collision Monte Carlo simulation code, SiMTRA, was adapted in order to simulate the energy, mass, and angular distribution of the high energy negative ions. All simulated distributions, for both planar and rotating cylindrical magnetrons, were in excellent correspondence with the experimental observations. Also a model for the amount of high energy negative O{sup -} ions was proposed. Indeed, the logarithm of the amount of high energy negative O{sup -} ions is shown to be related to the secondary electron emission yield of the oxide target, and these two parameters are known to be related to the work function. The SiMTRA simulations, in combination with knowledge of the work function or secondary electron emission yield of the target, allow modeling the flux of high energy negative ions during reactive magnetron sputtering.

36 MATERIALS SCIENCE↗

Monolayer graphene growth on sputtered thin film platinum

It is demonstrated that sputtered thin film platinum (Pt) can be used as a catalytic metal for graphene growth on metal. During the crystallization annealing, the sputtered Pt is crystallized mostly into Pt (111) orientation, maintaining excellent surface roughness with no sign of agglomeration. The relatively lower carbon solubility in Pt and the good surface roughness of the thin film Pt enable us to form a uniform monolayer graphene on Pt over the entire region of the thin film Pt/SiO{sub 2}/Si substrate by carbon dissolution and segregation method processed in a methane ambient. The monolayer graphene grown on Pt has been successfully transferred to SiO{sub 2}/Si substrate by simple wet etching of Pt. The results of Raman spectroscopic and scanning tunneling microscopic measurements of the synthesized graphene layer are presented.

36 MATERIALS SCIENCE↗

Velocity distribution function of sputtered Cu atoms obtained by time resolved optical absorption spectroscopy

A new method based on time resolved optical absorption spectroscopy is proposed to determine the velocity distribution function of sputtered Cu atoms in a magnetron plasma discharge. The method consists of applying a short pulse of 1.5 {mu}s and of recording time variations in copper atom density in off pulse at different positions (1, 2, and 3 cm) from target surface under 3-30 mTorr. The time evolution of the density is then converted into velocity distribution. We estimate that only sputtered atoms with radial velocity component lower than 0.5 km/s are detected. The average velocity of Cu atoms is evaluated as the first order moment of the velocity distribution functions. The velocity distribution functions become the more dispersive the farther from target surface. The average velocities vary in the range of 2.5-3 km/s at the vicinity of target surface whereas at 3 cm a decrease from 2.5 to 1.2 km/s is observed at 30 mTorr.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Dynamics of reactive high-power impulse magnetron sputtering discharge studied by time- and space-resolved optical emission spectroscopy and fast imaging

Time- and space-resolved optical emission spectroscopy and fast imaging were used for the investigation of the plasma dynamics of high-power impulse magnetron sputtering discharges. 200 {mu}s pulses with a 50 Hz repetition frequency were applied to a Cr target in Ar, N{sub 2}, and N{sub 2}/Ar mixtures and in a pressure range from 0.7 to 2.66 Pa. The power density peaked at 2.2-6 kW cm{sup -2}. Evidence of dominating self-sputtering was found for all investigated conditions. Up to four different discharge phases within each pulse were identified: (i) the ignition phase, (ii) the high-current metal-dominated phase, (iii) the transient phase, and (iv) the low-current gas-dominated phase. The emission of working gas excited by fast electrons penetrating the space in-between the electrodes during the ignition phase spread far outwards from the target at a speed of 24 km s{sup -1} in 1.3 Pa of Ar and at 7.5 km s{sup -1} in 1.3 Pa of N{sub 2}. The dense metal plasma created next to the target propagated in the reactor at a speed ranging from 0.7 to 3.5 km s{sup -1}, depending on the working gas composition and the pressure. In fact, it increased with higher N{sub 2} concentration and lower pressure. The form of the propagating plasma wave changed from a hemispherical shape in Ar, to a droplike shape extending far from the target in N{sub 2}. An important N{sub 2} emission rise in the latter case was detected during the transition at the end of the metal-dominated phase.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Rotating cylindrical magnetron sputtering: Simulation of the reactive process

A rotating cylindrical magnetron consists of a cylindrical tube, functioning as the cathode, which rotates around a stationary magnet assembly. In stationary mode, the cylindrical magnetron behaves similar to a planar magnetron with respect to the influence of reactive gas addition to the plasma. However, the transition from metallic mode to poisoned mode and vice versa depends on the rotation speed. An existing model has been modified to simulate the influence of target rotation on the well known hysteresis behavior during reactive magnetron sputtering. The model shows that the existing poisoning mechanisms, i.e., chemisorption, direct reactive ion implantation and knock on implantation, are insufficient to describe the poisoning behavior of the rotating target. A better description of the process is only possible by including the deposition of sputtered material on the target.

36 MATERIALS SCIENCE↗

Ion flux characteristics and efficiency of the deposition processes in high power impulse magnetron sputtering of zirconium

High power impulse magnetron sputtering of zirconium was investigated at the average target power density of up to 2.22 kW cm{sup -2} in a pulse. The depositions were performed using a strongly unbalanced magnetron with a planar zirconium target of 100 mm diameter at the argon pressure of 1 Pa. The repetition frequency was 500 Hz at duty cycles ranging from 4% to 10%. Time-averaged mass spectroscopy was carried out at the substrate positions of 100 and 200 mm from the target. The increase in the average target power density from 0.97 kW cm{sup -2} to 2.22 kW cm{sup -2} in shortened voltage pulses (from 200 to 80 {mu}s) at an average target power density of 100 W cm{sup -2} in a period led to high fractions (21%-32%) of doubly charged zirconium ions in total ion fluxes onto the substrate located 100 mm from the target. However, the respective fractions of singly charged zirconium ions decreased from 23% to 3%. It was observed that ion energy distributions were extended to high energies (up to 100 eV relative to the ground potential) under these conditions. The increased target power densities during the shortened voltage pulses resulted in a reduced deposition rate of films from 590 to 440 nm/min and in a weakly decreasing ionized fraction (from 55% to 49%) of the sputtered zirconium atoms in the flux onto the substrate. The doubly charged zirconium ions became strongly predominant (up to 63%) in the total ion flux onto the substrate at the distance of 200 mm from the target. Model calculations were carried out to explain the complicated deposition processes.

36 MATERIALS SCIENCE↗

Room-temperature infrared photoluminescence from sputter-deposited InN films

Wurtzite InN films are deposited on Si(100) and glass substrates by reactive rf-magnetron sputtering at a substrate temperature of 300 deg. C. The InN films have high electron concentrations of n{approx}4x10{sup 20} cm{sup -3} at 300 K. The optical band-gap energy is determined to be {approx}1.4 eV at 300 K. This value is considerably smaller than the previously reported value of {approx}2 eV in sputter-deposited InN films. Strong infrared photoluminescence (PL) with a peak at {approx}1.3 eV is also observed at room temperature. Thermal annealing in dry N{sub 2} atmosphere at 600 deg. C changes the deposited film from wurtzite InN to a cubic In{sub 2}O{sub 3} that still exhibits PL emission but in the visible spectral region ({approx}2 eV).

36 MATERIALS SCIENCE↗

Tilt angle control of nanocolumns grown by glancing angle sputtering at variable argon pressures

We show that the tilt angle of nanostructures obtained by glancing angle sputtering is finely tuned by selecting the adequate argon pressure. At low pressures, a ballistic deposition regime dominates, yielding high directional atoms that form tilted nanocolumns. High pressures lead to a diffusive regime which gives rise to vertical columnar growth. Monte Carlo simulations reproduce the experimental results indicating that the loss of directionality of the sputtered particles in the gas phase, together with the self-shadowing mechanism at the surface, are the main processes responsible for the development of the columns.

36 MATERIALS SCIENCE↗