Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SINTERED MATERIALS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

A highly durable injector faceplate design concept for O2/H2 propellants

Two different O2/H2 injector faceplate designs were used in a test bed rocket engine at the NASA Lewis Research Center facility. This test bed was operated in a pulsing mode to evaluate thrust chamber wall materials and coatings. Degradation of the sintered mesh injector face plates resulted in the substitution of a photoetched diffusion-bonded platelet faceplate. This faceplate accumulated over 4200 thermal cycles without damage or degradation. Prior testing for a total of 17,446 cycles required 19 sintered mesh faceplates. This average of 918 cycles per unit showed the diffusion bonded faceplate to have a thermal cycle capability ranging from 150 to 500 percent of that of the sintered wire unit. The test data also showed that the diffusion-bonded faceplate provided a more uniform flow of gaseous H2 through its discrete and uniformly spaced propellant orifices resulting in enhanced face cooling (no local hot spots) and increased performance. The injector faceplate designs are described and the results of the injector comparison test data are presented.

Mueggenburg, H. H.↗

Characterization of cobalt-dipped nickel electrodes with fibrex substrates

Nickel electrodes using fibrous substrates have poorer initial utilization of the active material than those using conventional nickel sinter substrates. Previous investigators had shown that utilization can be dramatically improved by dipping these electrodes in a cobalt solution immediately after the electrochemical impregnation, before formation and cycling is carried out. The present study looked at the gas evolution behavior of dipped and undipped electrodes, impedance curves, and the charge-discharge curves to try to understand the reasons for the improvement in utilization. Impedance measurements under open circuit conditions indicate that some of the improvement is due to a reduction in the ohmic resistance of the surface layer of the particles, in agreement with earlier work. The charge-discharge curves suggest that there may also be an additional increase in the ohmic resistance of the surface layer of the undipped electrode during charging.

Youngman, Carolyn A.↗

Lightweight Cathodes For Nickel Batteries

Lightweight cathodes for rechargeable nickel-based electrochemical cells undergoing development. In cathodes, mats of nickel fibers are substrates providing structural support of, and electrical contact with, active cathode material. Offers specific energies greater than sintered nickel plaque cathodes. Electrodes used in rechargeable batteries for applications in which weight major concern, including laptop computers, cellular phones, flashlights, soldiers' backpacks, and electric vehicles.

Britton, Doris L.↗

Transparent ceramic photo-optical semiconductor high power switches

A photoconductive semiconductor switch according to one embodiment includes a structure of sintered nanoparticles of a high band gap material exhibiting a lower electrical resistance when excited by light relative to an electrical resistance thereof when not exposed to the light. A method according to one embodiment includes creating a mixture comprising particles, at least one dopant, and at least one solvent; adding the mixture to a mold; forming a green structure in the mold; and sintering the green structure to form a transparent ceramic. Additional system, methods and products are also presented.

36 MATERIALS SCIENCE↗

Unusual Li 2 O sublimation promotes single-crystal growth and sintering

Li 2 O is rarely used for cathode material synthesis due to its high melting point (1,438 °C). Here we discover that Li 2 O can sublimate at 800-1,000 °C under ambient pressure, opening new possibilities for cathode synthesis. We propose a mechanism that enables synthesis of single crystals-such as LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) or LiNi 0.9 Mn 0.05 Co 0.05 O 2 (NMC90)-without direct contact with Li 2 O salts. We show that Li 2 O vapour successfully converts spent polycrystalline NMC811 into segregated single crystals without milling or post-treatment. The Li 2 O vapour, derived from Li 2 O solids, diffuses rapidly and reacts with precursors, mimicking a molten-salt environment, which facilitates single-crystal growth. The chemical lithiation process continuously drives Li 2 O sublimation, sintering the crystals. Single crystals derived from Li 2 O and fresh precursors or spent polycrystals exhibit outstanding cycling after 1,000 cycles in full cells. The demonstrated Li 2 O sublimation and its universal role in promoting single-crystal growth provides an effective approach for single-crystal synthesis, scale-up and recycling.

25 ENERGY STORAGE↗

Development of Bulk Nanocrystalline Cemented Tungsten Carbide for Industrial Applicaitons

This report contains detailed information of the research program entitled "Development of Bulk Nanocrystalline Cemented Tungsten Carbide Materials for Industrial Applications". The report include the processes that were developed for producing nanosized WC/Co composite powders, and an ultrahigh pressure rapid hot consolidation process for sintering of nanosized powders. The mechanical properties of consolidated materials using the nanosized powders are also reported.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Method to Determine Maximum Allowable Sinterable Silver Interconnect Size

The use of sintered-silver for large-area interconnection is attractive for some large-area bonding applications in power electronics such as the bonding of metal-clad, electrically-insulating substrates to heat sinks. Arrays of different pad sizes and pad shapes have been considered for such large area bonding; however, rather than arbitrarily choosing their size, it is desirable to use the largest size possible where the onset of interconnect delamination does not occur. If that is achieved, then sintered-silver's high thermal and electrical conductivities can be fully taken advantage of. Toward achieving this, a simple and inexpensive proof test is described to identify the largest achievable interconnect size with sinterable silver. The method's objective is to purposely initiate failure or delamination. Copper and invar (a ferrous-nickel alloy whose coefficient of thermal expansion (CTE) is similar to that of silicon or silicon carbide) disks were used in this study and sinterable silver was used to bond them. As a consequence of the method's execution, delamination occurred in some samples during cooling from the 250 degrees C sintering temperature to room temperature and bonding temperature and from thermal cycling in others. These occurrences and their interpretations highlight the method's utility, and the herein described results are used to speculate how sintered-silver bonding will work with other material combinations.

30 DIRECT ENERGY CONVERSION↗

Interfacial reactions and wetting in Al-Mg sintered by powder metallurgy process

Was conducted to analyze the effect of temperature variation on the bonding interface sintered composite Al-Mg and analyze the effect of variations of the density and hardness sinter. Research carried out by the base material powders of Al, Mg powder and solvent n-butanol. The method used in this study is a powder metallurgy, with a composition of 60% volume fraction of Al - 40% Mg. Al-Mg mixing with n-butanol for 1 hour at 500 rpm. Then the emphasis (cold comression) with a size of 1.4 cm in diameter dies and height of 2.8 cm, is pressed with a force of 20 MPa and held for 15 minutes. After the sample into pellets, then sintered at various temperatures 300 °C, 350 °C, 400 °C and 450 °C. Characterization is done by using the testing green density, sintered density, X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), vickers microhardness, and press test. XRD data analysis done by using X’Pert High Score Plus (HSP) to determine whether there is a new phase is formed. Test results show that the sintered density increasing sintering temperature, the resulting density is also increasing (shrinkage). However, at a temperature of 450 °C decreased (swelling). With the increased sinter density, interfacial bonding getting Kuta and more compact so that its hardness is also increased. From the test results of SEM / EDX, there Mg into Al in the border area. At temperatures of 300 °C, 350 °C, 400 °C, the phase formed is Al, Mg and MgO. While phase is formed at a temperature of 450 °C is aluminum magnesium (Al{sub 3}Mg{sub 2}), Aluminum Magnesium Zinc (AlMg{sub 2}Zn).

36 MATERIALS SCIENCE↗

Unraveling the multi-step crystallization mechanism of polytetrafluoroethylene, modified polytetrafluoroethylene, and their nanocomposites with boron nitride nanobarbs: Experimental insights and theoretical analysis

The non-isothermal crystallization behavior and kinetics of polytetrafluoroethylene (PTFE) composites with boron nitride nanobarb (BNNB), a new generation nanostructure with unique surface morphology and mechanical “barbs” have been analyzed, understanding these properties is essential for their high-end applications as thermal interface materials (TIM) for microwave, 5G and microelectronic devices. The analysis of the crystallization parameters includes crystallization onset, peak and end temperatures, crystallization half-life and overall crystallinity of PTFE, modified PTFE and their BNNB composites. The results were further analyzed using theoretical models such as the combined Avrami-Ozawa model. It was found that BNNB supports crystallization in the modified PTFE but shows minimal effect on the crystallization of PTFE. Due to the limitation of the classical theoretical models used above in fully characterizing the multi-step crystallization process of PTFE, an in-depth analysis using the model-free advanced isoconversional computation was used to characterize the PTFE crystallization based on the evolution of activation energy with fractional crystallinity and for the first time with temperature. Three kinetic regions were identified in the crystallization mechanism. Here, this study investigated the molecular organization and microstructural evolution of PTFE, modified PTFE and their composites during non-isothermal crystallization using advanced X-ray scattering measurements. An insight into the changes undergone by the material's microstructural units including crystallite size and morphology, lamellar thickness and lamellar interfacial layer thickness, and crystallographic phase dynamics during non-isothermal cooling from the melt, was provided here in this work. The effect of copolymer modification of PTFE and the inclusion of pristine and functionalized BNNB (a thermally conductive and electrically insulating ceramic) are both new investigations that provide valuable knowledge for the development of materials with strong matrix-nanofiller interaction and guidance for optimizing sintering and cooling cycles, two key steps in PTFE processing that largely affect the material microstructural features. Overall, the result of the three-part investigation demonstrates that BNNB supports crystallization in the modified PTFE up to 20 wt% concentration and at low and high cooling rates typically used in the industrial processing of PTFE.

36 MATERIALS SCIENCE↗

Enhancing CMC Temperature Performance in High Hydrogen Environments using Field Assisted Sintering Technology

This final report summarizes the developments in field assisted sintering technology (FAST) for rapid fabrication of ceramic matrix composite (CMC) materials with integrated environmental barrier coatings (EBCs), as well as their performance in a representative gas turbine combustor environment including stagnant flame zones, and high velocity product zones. CMCs are a possible high temperature tolerant material system for gas turbine engines, which are currently the dominant source of electric power production and the primary source of aircraft propulsion. However, CMCs are costly and time-consuming (on the order of weeks to months) to fabricate, and CMCs based on silicon carbide (SiC) ceramics are susceptible to water vapor degradation requiring the use of specialized EBCs. The manufacturing technique known as FAST can create consolidated parts in as little as a few hours using high pressure and temperature, and may be useful to integrate EBCs into CMCs directly during consolidation.

08 HYDROGEN↗

Consortium for materials development in space

The status of the Consortium for Materials Development in Space (CMDS) is reviewed. Individual CMDS materials projects and flight opportunities on suborbital and orbital carriers are outlined. Projects include: surface coatings and catalyst production; non-linear optical organic materials; physical properties of immiscible polymers; nuclear track detectors; powdered metal sintering; iron-carbon solidification; high-temperature superconductors; physical vapor transport crystal growth; materials preparation and longevity in hyperthermal oxygen; foam formation; measurement of the microgravity environment; and commercial management of space fluids.

Source record↗

Process Developed for Generating Ceramic Interconnects With Low Sintering Temperatures for Solid Oxide Fuel Cells

Solid oxide fuel cells (SOFCs) have been considered as premium future power generation devices because they have demonstrated high energy-conversion efficiency, high power density, and extremely low pollution, and have the flexibility of using hydrocarbon fuel. The Solid-State Energy Conversion Alliance (SECA) initiative, supported by the U.S. Department of Energy and private industries, is leading the development and commercialization of SOFCs for low-cost stationary and automotive markets. The targeted power density for the initiative is rather low, so that the SECA SOFC can be operated at a relatively low temperature (approx. 700 C) and inexpensive metallic interconnects can be utilized in the SOFC stack. As only NASA can, the agency is investigating SOFCs for aerospace applications. Considerable high power density is required for the applications. As a result, the NASA SOFC will be operated at a high temperature (approx. 900 C) and ceramic interconnects will be employed. Lanthanum chromite-based materials have emerged as a leading candidate for the ceramic interconnects. The interconnects are expected to co-sinter with zirconia electrolyte to mitigate the interface electric resistance and to simplify the processing procedure. Lanthanum chromites made by the traditional method are sintered at 1500 C or above. They react with zirconia electrolytes (which typically sinter between 1300 and 1400 C) at the sintering temperature of lanthanum chromites. It has been envisioned that lanthanum chromites with lower sintering temperatures can be co-fired with zirconia electrolyte. Nonstoichiometric lanthanum chromites can be sintered at lower temperatures, but they are unstable and react with zirconia electrolyte during co-sintering. NASA Glenn Research Center s Ceramics Branch investigated a glycine nitrate process to generate fine powder of the lanthanum-chromite-based materials. By simultaneously doping calcium on the lanthanum site, and cobalt and aluminum on the chromium site, we could sinter the materials below 1400 C. The doping concentrations were adjusted so that the thermal expansion coefficient matched that of the zirconia electrolyte. Also, the investigation was focused on stoichiometric compositions so that the materials would have better stability. Co-sintering and chemical compatibility with zirconia electrolyte were examined by X-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy (line scanning and dot map). The results showed that the materials bond well, but do not react, with zirconia electrolyte. The electric conductivity of the materials measured at 900 C in air was about 20 S/cm.

Zhong, Zhi-Min↗

Sinter-Bonding of AISI 316L and 17-4 PH Stainless Steels

The sinter-bonding method was used to produce AISI 316L/17-4 PH components by conventional powder metallurgy technology. The production process consisted of following steps: the powder layering, co-pressing and co-sintering processes. The co-sintering process was carried out at different sintering temperatures (1200, 1250 and 1300 °C), and times (60, 90 and 120 min) in hydrogen atmosphere. The effect of co-pressing and co-sintering conditions on the ability to create a permanent connection between AISI 316L and 17-4 PH stainless steels was investigated. The densification, dimensional change and microstructural evolution of sintered AISI 316L/17-4 PH components were studied. The increase in co-pressing pressure as well as using of the longer time and the higher temperature of co-sintering process contributed to increase in AISI 316L/17-4 PH component density. The dilatometric study as well as dimensional changes measurements revealed an appropriate sintering compatibility for AISI 316L and 17-4PH steels when the sintering process was carried out at the temperature of 1200 °C for time ranging from 60 to 120 min and at 1250 °C for shorter sintering times. The sintering at temperature of 1300 °C (regardless of other manufacturing conditions) led to a significant deviation from the cylindrical shape of samples, as a result of difference of shrinkage of AISI 316L and 17-4 PH steels. Microstructural study indicated that AISI 316L and 17-4 PH steels creates a good diffusion joint (without any cracks and warpage) during the high-temperature sintering process. Nickel diffusion takes place from the AISI 316L to 17-4 PH stainless steel, and copper and molybdenum diffuse in opposite direction of nickel diffusion. It is possible to achieve a solid connection between two materials exhibiting difference in chemical composition by using sinter-bonding and conventional powder metallurgy technology.

36 MATERIALS SCIENCE↗

Regolith-Derived Heat Shield for Planetary Body Entry and Descent System with In Situ Fabrication

In this paper we will discuss a new mass-efficient and innovative way of protecting high-mass spacecraft during planetary Entry, Descent & Landing (EDL). Heat shields fabricated in situ can provide a thermal-protection system (TPS) for spacecraft that routinely enter a planetary atmosphere. By fabricating the heat shield with space resources from regolith materials available on moons and asteroids, it is possible to avoid launching the heat-shield mass from Earth. Three regolith processing and manufacturing methods will be discussed: 1) oxygen & metal extraction ISRU processes produce glassy melts enriched in alumina and titania, processed to obtain variable density, high melting point and heat-resistance; 2) compression and sintering of the regolith yield low density materials; 3) in-situ derived high-temperature polymers are created to bind regolith particles together, with a lower energy budget.

Hogue, Michael D.↗

A Rapid Sintering Method for Cerium Nitride Pellet: A Uranium Mononitride Surrogate

Uranium mononitride (UN) is a candidate fuel material for light water reactors with higher uranium (U) loading and thermal conductivity than uranium dioxide (UO 2 ). However, the sintering of UN pellets is challenging as the UN powder particles oxidize rapidly at high temperatures unless the oxygen concentration is extremely low. Oxidation during sintering either reduces the relative density of the sintered UN pellet or disintegrates the sintered UN pellet to powder. To address this problem, the present work developed a rapid sintering method for producing highly densified UN surrogate pellets with minimal oxidation. Cerium nitride (CeN) is used as a surrogate for UN to reduce radiation hazards. With the custom-developed fast-heating system, the sintering process was completed within 150 s. The sintering atmosphere was flowing nitrogen (N 2 ). The sintered CeN pellet density was 95% of the theoretical density (TD) or higher. The microstructure was uniform with a 10–25 µm grain size as demonstrated by scanning electron microscopy (SEM) and contained trivial levels of oxides as demonstrated by X-ray diffraction (XRD). The resultant pellets indicate that the rapid sintering method is a promising method to make UN fuel pellets with equivalent or higher density to pellets made by conventional sintering methods, while also being more efficient in time and costs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗