Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Polymer morphology”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Resolving the Atomic Structure of Sequential Infiltration Synthesis Derived Inorganic Clusters

Sequential infiltration synthesis (SIS) is a route to the precision deposition of inorganic solids in analogy to atomic layer deposition but occurs within (vs upon) a soft material template. SIS has enabled exquisite nanoscale morphological complexity in various oxides through selective nucleation in block copolymers templates. However, the earliest stages of SIS growth remain unresolved, including the atomic structure of nuclei and the evolution of local coordination environments, before and after polymer template removal. We employed In K-edge extended X-ray absorption fine structure and atomic pair distribution function analysis of high-energy X-ray scattering to unravel (1) the structural evolution of InO x H y clusters inside a poly(methyl methacrylate) (PMMA) host matrix and (2) the formation of porous In 2 O 3 solids (obtained after annealing) as a function of SIS cycle number. Early SIS cycles result in InO x H y cluster growth with high aspect ratio, followed by the formation of a three-dimensional network with additional SIS cycles. That the atomic structures of the InO x H y clusters can be modeled as multinuclear clusters with bonding patterns related to those in In 2 O 3 and In(OH) 3 crystal structures suggests that SIS may be an efficient route to 3D arrays of discrete-atom-number clusters. As a result, annealing the mixed inorganic/polymer films in air removes the PMMA template and consolidates the as-grown clusters into cubic In 2 O 3 nanocrystals with structural details that also depend on SIS cycle number.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Discharge Rate‐Driven Li 2 O 2 Growth Exhibits Unconventional Morphology Trends in Solid‐State Li‐O 2 Batteries

Solid-state lithium oxygen batteries (LOBs) are known for their enhanced safety, higher electrochemical stability, and improved energy density compared to liquid-state LOBs. However, the investigation of solid-state LOBs is limited with little understanding of their discharge and charge processes. In this work, a polymer-based solid-state LOB is used to investigate the effect of discharge rate on lithium peroxide (Li 2 O 2 ) formation, the oxygen evolution reaction (OER), and cycle performance. Notably, we observe a counterintuitive trend: Li 2 O 2 particle size increases with increasing discharge current density, in contrast to liquid systems. This behavior arises from inherent space charge layers that restrict Li⁺ transport under high current, and spatially heterogeneous active sites at the solid electrolyte–cathode interface, directly evidenced by small angle X-ray scattering (SAXS), which govern nucleation accessibility and promote site-selective Li 2 O 2 growth. Furthermore, higher current densities improve ORR and OER efficiency but accelerate anode degradation, while lower currents promote side reactions. These opposing effects result in a trade-off that defines an optimal discharge rate (0.1 mA cm -2 ) for maximizing cycle life. This study provides a new mechanistic perspective on discharge-driven processes in solid-state LOBs and offers practical guidelines for performance optimization in future high-energy battery systems.

Discharge current density↗
DOE OSTI2023

Nanotomography Investigation of 3D Printed Batteries with a Water-in-Salt Gel Polymer Electrolyte

3D printing, also known as additive manufacturing, has emerged as a promising strategy to design and fabricate future energy storage devices. Although significant progress has been reported, current 3D printed battery designs are still limited by the choice of the electrolyte, such as ceramic or conventional toxic organic electrolytes. Here, we incorporated the latest developments in aqueous batteries into a novel 3D printable battery that can be fabricated directly in an ambient environment that is also more environmentally friendly. Specifically, a gel polymer electrolyte with a water-in-salt concept was introduced in our 3D-printed batteries. Combining their advantages, the resulting 3D printable batteries show promise for much simplified processing conditions. Further, the structural, (electro-)chemical, and morphological evolution batteries are being investigated by synchrotron X-ray nanotomography and electrochemical analysis. Overall, our research explores the possibility of an easier and more environmentally friendly way to build 3D printable, customizable batteries for future technologies.

36 MATERIALS SCIENCE↗
NASA NTRS1994

Reactive Melt Infiltration of Silicon-Niobium Alloys in Microporous Carbons

Studies of the reactive melt infiltration of silicon-niobium alloys in microporous carbon preforms prepared by the pyrolysis of a polymer precursor have been carried out using modeling, Differential Thermal Analysis (DTA), and melt infiltration. Mercury porosimetry results indicate a very narrow pore size distribution with virtually all the porosity within the carbon preforms open to infiltrants. The morphology and amount of the residual phases (niobium disilicide and silicon) in the infiltrated material can be tailored according to requirements by careful control of the properties (pore size and pore volume) of the porous carbon preforms and alloy composition. The average room temperature four-point flexural strength of a reaction-formed silicon carbide material (made by the infiltration of medium pore size carbon preform with Si - 5 at. % Nb alloy) is 290 +/- 40 MPa (42 +/- 6 ksi) and the fracture toughness is 3.7 +/- 0.3 MPa square root of m. The flexural strength decreases at high temperatures due to relaxation of residual thermal stresses and the presence of free silicon in the material.

Singh, M.↗
NASA NTRS1999

Materials Science Experiments on the International Space Station

The Performance Goal for NASA's Microgravity Materials Science Program reads "Use microgravity to establish and improve quantitative and predictive relationships between the structure, processing and properties of materials." The advent of the International Space Station will open up a new era in Materials Science Research including the ability to perform long term and frequent experiments in microgravity. As indicated the objective is to gain a greater understanding of issues of materials science in an environment in which the force of gravity can be effectively switched off. Thus gravity related issues of convection, buoyancy and hydrostatic forces can be reduced and the science behind the structure/processing/properties relationship can more easily be understood. The specific areas of research covered within the program are (1) the study of Nucleation and Metastable States, (2) Prediction and Control of Microstructure (including pattern formation and morphological stability), (3) Phase Separation and Interfacial Stability, (4) Transport Phenomena (including process modeling and thermophysical properties measurement), and (5) Crystal Growth, and Defect Generation and Control. All classes of materials, including metals and alloys, glasses and ceramics, polymers, electronic materials (including organic and inorganic single crystals), aerogels and nanostructures, are included in these areas. The principal experimental equipment available to the materials scientist on the International Space Station (ISS) will be the Materials Science Research Facility (MSRF). Each of these systems will be accommodated in a single ISS rack, which can operate autonomously, will accommodate telescience operations, and will provide real time data to the ground. Eventual plans call for three MSRF racks, the first of which will be shared with the European Space Agency (ESA). Under international agreements, ESA and other partners will provide some of the equipment, while NASA covers launch and integration costs. The MSRF facilities will include modular components, which can be exchanged to provide inserts specifically matched to the engineering requirements of the particular Principal Investigator. To defray costs and avoid duplication of engineering effort NASA is also pursuing the possibility of using facilities provided by international partners. By this means it is anticipated that all of the types of research outlined in the previous paragraph can be done on the ISS.

Gillies, Donald C.↗
DOE OSTI2021

Recent Developments in Femtosecond Laser-Enabled TriBeam Systems

Streams of multimodal three-dimensional (3D) and four-dimensional (4D) data are revolutionizing our ability to design and predict the behavior of a broad array of advanced materials systems. Over the last 10 years, a new 3D imaging platform consisting of a femtosecond (fs) pulsed laser coupled with a focused ion beam scanning electron microscope (FIB SEM) has been developed by UC Santa Barbara in collaboration with Thermo Fisher Scientific (formerly FEI). The femtosecond-laser-enabled FIB SEM, called the TriBeam, has become one of the only 3D serial sectioning methods available that can gather millimeter-scaled multimodal datasets at sub-μm voxel resolutions; these length scales are critical for many materials problems. Multimodal chemical, crystallographic, and morphological information can be gathered rapidly on a layer-by-layer basis and reconstructed in 3D. Large (gigabyte to terabyte scale) 3D datasets have been generated for a broad array of materials systems, including metallic alloys, ceramics, biomaterials, polymer- and ceramic-matrix composites, and semiconductors. The research tasks conducted have resulted in a completely new design, operating with a dual-wavelength femtosecond-pulsed laser on a plasma focused ion beam (PFIB) platform.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Formation Mechanism of Flower-like Polyacrylonitrile Particles

Flower-like polyacrylonitrile (PAN) particles have shown promising performance for numerous applications, including sensors, catalysis, and energy storage. However, the detailed formation process of these unique structures during polymerization has not been investigated. Here, we elucidate the formation process of flower-like PAN particles through a series of in situ and ex situ experiments. We have the following key findings. First, lamellar petals within the flower-like particles were predominantly orthorhombic PAN crystals. Second, branching of the lamellae during the particle formation arose from PAN's fast nucleation and growth on pre-existing PAN crystals, which was driven by the poor solubility of PAN in the reaction solvent. Third, the particles were formed to maintain a constant center-to-center distance during the reaction. The separation distance was attributed to strong electrostatic repulsion, which resulted in the final particles' spherical shape and uniform size. Lastly, we employed the understanding of the formation mechanism to tune the PAN particles' morphology using several experimental parameters including incorporating comonomers, changing temperature, adding nucleation seeds, and adjusting the monomer concentration. Here these findings provide important insights into the bottom-up design of advanced nanostructured PAN-based materials and controlled polymer nanostructure self-assemblies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Enhanced ordering in length-polydisperse carbon nanotube solutions at high concentrations as revealed by small angle X-ray scattering

Carbon nanotubes (CNTs) are stiff, all-carbon macromolecules with diameters as small as one nanometer and few microns long. Solutions of CNTs in chlorosulfonic acid (CSA) follow the phase behavior of rigid rod polymers interacting via a repulsive potential and display a liquid crystalline phase at sufficiently high concentration. Here, we show that small-angle X-ray scattering and polarized light microscopy data can be combined to characterize quantitatively the morphology of liquid crystalline phases formed in CNT solutions at concentrations from 3 to 6.5% by volume. We find that upon increasing their concentration, CNTs self-assemble into a liquid crystalline phase with a pleated texture and with a large inter-particle spacing that could be indicative of a transition to higher-order liquid crystalline phases. We explain how thermal undulations of CNTs can enhance their electrostatic repulsion and increase their effective diameter by an order of magnitude. By calculating the critical concentration, where the mean amplitude of undulation of an unconstrained rod becomes comparable to the rod spacing, we find that thermal undulations start to affect steric forces at concentrations as low as the isotropic cloud point in CNT solutions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Seeking regularity from irregularity: unveiling the synthesis–nanomorphology relationships of heterogeneous nanomaterials using unsupervised machine learning

Nanoscale morphology of functional materials determines their chemical and physical properties. However, despite increasing use of transmission electron microscopy (TEM) to directly image nanomorphology, it remains challenging to quantify the information embedded in TEM data sets, and to use nanomorphology to link synthesis and processing conditions to properties. We develop an automated, descriptor-free analysis workflow for TEM data that utilizes convolutional neural networks and unsupervised learning to quantify and classify nanomorphology, and thereby reveal synthesis–nanomorphology relationships in three different systems. While TEM records nanomorphology readily in two-dimensional (2D) images or three-dimensional (3D) tomograms, we advance the analysis of these images by identifying and applying a universal shape fingerprint function to characterize nanomorphology. After dimensionality reduction through principal component analysis, this function then serves as the input for morphology grouping through unsupervised learning. We demonstrate the wide applicability of our workflow to both 2D and 3D TEM data sets, and to both inorganic and organic nanomaterials, including tetrahedral gold nanoparticles mixed with irregularly shaped impurities, hybrid polymer-patched gold nanoprisms, and polyamide membranes with irregular and heterogeneous 3D crumple structures. In each of these systems, unsupervised nanomorphology grouping identifies both the diversity and the similarity of the nanomaterial across different synthesis conditions, revealing how synthetic parameters guide nanomorphology development. Our work opens possibilities for enhancing synthesis of nanomaterials through artificial intelligence and for understanding and controlling complex nanomorphology, both for 2D systems and in the far less explored case of 3D structures, such as those with embedded voids or hidden interfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1994

Atomic Oxygen (ATOX) simulation of Teflon FEP and Kapton H surfaces using a high intensity, low energy, mass selected, ion beam facility

A high intensity (greater than 10(exp 15) ions/sq cm) low energy (down to 5 eV) mass selected ion beam (MSIB) facility was used to study the effects of ATOX on two polymers commonly used for space applications (Kapton H and Teflon FEP). The polymers were exposed to O(+) and Ne(+) fluences on 10(exp 15) - 10(exp 19) ions/sq cm, using 30eV ions. A variety of analytical methods were used to analyze the eroded surfaces including: (1) atomic force microscopy (AFM) for morphology measurements; (2) total mass loss measurements using a microbalance; (3) surface chemical composition using x-ray photoelectron spectroscopy (XPS), and (4) residual gas analysis (RGA) of the released gases during bombardment. The relative significance of the collisional and chemical degradation processes was evaluated by comparing the effects of Ne(+) and O(+) bombardment. For 30 eV ions it was found that the Kapton is eroded via chemical mechanisms while Teflon FEP is eroded via collisional mechanisms. AFM analysis was found very powerful in revealing the evolution of the damage from its initial atomic scale (roughness of approx. 1 nm) to its final microscopic scale (roughness greater than 1 micron). Both the surface morphology and the average roughness of the bombarded surfaces (averaged over 1 micron x 1 micron images by the system's computer) were determined for each sample. For 30 eV a non linear increase of the Kapton roughness with the O(+) fluence was discovered (a slow increase rate for fluences phi less than 5 x 10(exp 17) O(+)/sq cm, and a rapid increase rate for phi greater than 5 x 10(exp 17) O(+)/sq cm). Comparative studies on the same materials exposed to RF and DC oxygen plasmas indicate that the specific details of the erosion depend on the simulation facility emphasizing the advantages of the ion beam facility.

Vered, R.↗
DOE OSTI2024

Assembling Vertical Block Copolymer Nanopores via Solvent Vapor Annealing on Homopolymer-Functionalized Substrates

Utilizing the self-assembly of block copolymers with large Flory–Huggins interaction parameters (χ) for nanofabrication is a formidable challenge due to the attendant large surface energy differences between the blocks. This work reports a robust protocol for the fabrication of thin films with highly ordered cylindrical nanopore arrays via the self-assembly of an asymmetric poly(styrene-block-4-vinylpyridine) (PS-b-P4VP) diblock copolymer blended with a P4VP homopolymer. The desired vertical domain orientation is achieved at the air–polymer interface by controlled solvent vapor annealing (SVA) using acetone, a solvent with weak selectivity for PS over P4VP, and at the substrate interface by functionalization using a hydroxy-terminated poly(2-vinylpyridine) (P2VP-OH) homopolymer brush. In contrast, the vertical cylinder orientation is unstable during acetone SVA on substrates functionalized using hydroxy-terminated poly(methyl methacrylate) (PMMA-OH). Although PMMA exhibits more balanced interfacial energies between PS and P4VP than P2VP in the dry state, it is also swollen more selectively by acetone. We hypothesize that the nearly balanced solvent swelling of the three polymers (P2VP, P4VP, and PS) stabilizes the vertical cylinder orientation, while unbalanced swelling (PMMA > P4VP and PS) does not. Here we further characterize pore formation by addition of a P4VP homopolymer and its postassembly extraction using ethanol, revealing a narrow window of pore size tunability. Notably, minimal differences in nanopore morphologies are observed for P4VP volume fractions as high as 0.1, regardless of the P4VP molar mass. However, further increasing the P4VP volume fraction results in domain reorientation or macrophase separation when its molar mass is less than or greater than the P4VP block molar mass, respectively. Using a P4VP homopolymer that is nearly equal in length to the P4VP block enables the fabrication of well-ordered arrays of vertical, through-film nanopores with high aspect ratios (>10), small periods (<23 nm), and diameters less than 10 nm.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Crystallization kinetics and nanoparticle ordering in semicrystalline polymer nanocomposites

There has been considerable interest in the nucleation and crystallization of polymers in the presence of nanoparticles (NPs, or nanofillers in general, NFs). Most of the extensive work in this area has focused on anisotropic, non-Brownian NFs (e.g., clay sheets, carbon nanotubes) whose spatial dispersion state in these nanocomposites is controlled by the process by which they are formed. Hence, NF spatial dispersion is generally limited and often remains poorly characterized. Thermodynamic handles that can be used to control NF dispersion state in the polymer melt include (a) favorable interactions between the polymer chains and the bare NP surfaces, or (b) the density and length of the chains, with the same chemistry as the matrix, grafted to the NP surface. These relatively large NFs merely act as stationary objects that affect the kinetics of nucleation by providing heterogeneous sites, and the crystallization rate by confining the polymer in the melt state. The dispersion state of the NFs can dramatically affect the nucleation and crystallization of the matrix, but in most cases reported, the NFs increase nucleation efficiency relative to the neat polymer. At higher NF loadings, the effect of polymer confinement by the NFs dominates, leading to a decrease in crystal growth rates. This review describes the most important lessons learned from these commonly studied systems and then extends to polymer composite systems containing small, mobile spherical NPs (typically smaller than 100 nm in size). The role of NP mobility, which provides for dynamic confinement of the polymer melt, on the kinetics of polymer crystallization (nucleation, growth, and overall crystallization) and how this behavior is mostly consistent with the case of immobile NF is a second important focus of this review. In addition to the role of NFs on crystallization kinetics, recently reported nanoparticle ordering phenomena such as the effect of matrix crystallization on the organization of small spherical NPs within the amorphous regions of the semicrystalline morphology are discussed. In conclusion, such phenomena are clearly not observed for large NFs and hence provide a point of departure from past works in this area.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Understanding the Impacts of Support–Polymer Interactions on the Dynamics of Poly(ethyleneimine) Confined in Mesoporous SBA-15

Supported amines are a promising class of CO 2 sorbents offering large uptake capacities and fast uptake rates. Additionally, among supported amines, poly(ethyleneimine) (PEI) physically impregnated in the mesopores of SBA-15 silica is widely used. Within these composite materials, the chain dynamics and morphologies of PEI strongly influence the CO 2 capture performance, yet little is known about chain and macromolecule mobility in confined pores. Here, we probe the impact of the support–PEI interactions on the dynamics and structures of PEI at the support interface and the corresponding impact on CO 2 uptake performance, which yields critical structure–property relationships. The pore walls of the support are grafted with organosilanes with different chemical end groups to differentiate interaction modes (spanning from strong attraction to repulsion) between the pore surface and PEI. Combinations of techniques, such as quasi-elastic neutron scattering (QENS), 1 H T 1 –T 2 relaxation correlation solid-state NMR, and molecular dynamics (MD) simulations, are used to comprehensively assess the physical properties of confined PEI. We hypothesized that PEI would have faster dynamics when subjected to less attractive or repulsive interactions. However, we discover that complex interfacial interactions resulted in complex structure–property relationships. Indeed, both the chain conformation of the surface-grafted chains and of the PEI around the surface influenced the chain mobility and CO 2 uptake performance. By coupling knowledge of the dynamics and distributions of PEI with CO 2 sorption performance and other characteristics, we determine that the macroscopic structures of the hybrid materials dictate the first rapid CO 2 uptake, and the rate of CO 2 sorption during the subsequent gradual uptake stage is determined by PEI chain motions that promote diffusive jumps of CO 2 through PEI-packed domains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Zeolite‐Based Catalysts for Conversion of Oxygenated Polymer Waste by Positron Annihilation

Positron Annihilation Lifetime Spectroscopy (PALS) has been employed to investigate the catalysts HZSM-5 and MESO−Y, which play a pivotal role in catalyzing and upgrading plastics, with a primary focus on oxygenated polymers, thereby transforming existing plastic materials into simpler, higher-quality value-added products. Here, in this study, PALS was systematically compared with other complementary analytical techniques. The research outcomes have successfully demonstrated the efficacy of PALS in elucidating the morphology and topology of zeolites at micro/meso-meter scales. The first experiment focuses on H-ZSM-5 zeolite subjected to treatments involving polyurethane and polypropylene. The second experiment delves into H-ZSM-5 zeolites with varying Si/Al ratios, both before and after conversion. The third experiment investigates Y zeolites that are surfactant templated to induce meso-porosity, examining their fresh state as well as their post-conversion condition. The PALS analysis was supplemented by BET (Brunauer-Emmett-Teller) analysis and NMR (Nuclear Magnetic Resonance) spectroscopies. Notably, PALS exhibits superior sensitivity, at the sub-nanometer scale, suggesting its potential as a preferred complementary method for catalysis studies. In conclusion, the integration of PALS into the repertoire of analytical tools enhances our understanding of catalyst behavior and catalytic processes, offering valuable insights for the advancement of plastic recycling and catalysis research.

32 - ENERGY CONSERVATION, CONSUMPTION, AND UTILIZA↗
DOE OSTI2023

Preparation of Macroscopic Low-Density Gold Foams with Good Machinability

Uniform, macroscopic monoliths (ranging from a few millimeters to a centimeter) of low-density gold foams with ~95% porosity and ~10-μm-diameter pores were prepared by the casting of gold-coated polystyrene core-shell particles followed by the thermal removal of the polymer core. The Au foams were composed of unique hollow gold spheres and showed superior mechanical integrity and resilience compared to the foams we previously reported. Highly efficient seeding and electroless gold-plating methods in this study caused a significant morphological transition in the gold coatings from coarse particles to fine particles, and finally, to a continuous layer. A modified, scalable casting approach to form large uniform monoliths (up to ~1-cm diameter) and a gentle baking condition to minimize undesirable densification of the final foams enabled us to develop a simple, efficient synthetic route to nanostructured macroscopic low-density gold foams. To demonstrate the improved mechanical stability and machinability, a representative monolithic Au foam (~0.9 g/cm 3 ) was carefully cut into the hollow cylinder of gold foams by a series of machining and processing steps. Finally, we tried to understand the unique mechanical behaviors and properties of this gold foam by nanoindentation measurement.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2007

Multifunctional Composites for Improved Polyimide Thermal Stability

The layered morphology of silicate clay provides an effective barrier to oxidative degradation of the matrix resin. However, as resin thermal stability continues to reach higher limits, development of an organic modification with comparable temperature capabilities becomes a challenge. Typically, phyllosilicates used in polymer nanocomposites are modified with an alkyl ammonium ion. Such organic modifiers are not suited for incorporation into high temperature polymers as they commonly degrade below 200oC. Therefore, the development of nanoparticle specifically suited for high temperature applications is necessary. Several nanoparticles were investigated in this study, including pre-exfoliated synthetic clay, an organically modified clay, and carbon nanofiber. Dispersion of the layered silicate increases the onset temperature of matrix degradation as well as slows oxidative degradation. The thermally stable carbon nanofibers are also observed to significantly increase the resin thermal stability.

Miller, Sandi G.↗
DOE OSTI2022

Polyacrylonitrile-based electrolytes: How processing and residual solvent affect ion transport and stability

Polyacrylonitrile (PAN) is one of the alternative candidate polymer hosts to form solid polymer electrolytes (SPEs) besides the widely used poly(ethylene oxide). In this study, we systematically investigate the processing of PAN based SPEs containing lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt, using dimethylformamide (DMF) as the solvent. The effects of PAN processing procedure including solution mixing, casting, and drying on the morphology, ion transport, solvation structure, Li and oxidative stability of PAN electrolytes are thoroughly examined. In particular, four drying conditions are investigated and the amount of residual DMF is accurately determined using infrared (IR) spectroscopy. Varying the drying conditions can lead to five orders of magnitude decrease in the ionic conductivity. As DMF content decreases, the SPE's stability again Li metal dramatically improves. The practical oxidative stability is also strongly affected by the residual DMF content, ranging from 2.5 V to 3.5 V, much lower than reported values. Finally, the role of the residual DMF solvent is elucidated. DMF content vitally influences ion solvation structure at different concentration regimes, which ultimately dictates the ion conduction mechanism and oxidative stability of PAN based SPEs. In conclusion, this thorough study lays the groundwork for future development of PAN based electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗