SEARCH · Engineering Papers

Results for “Plating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Mean velocity, turbulence intensity, and scale in a subsonic turbulent jet impinging normal to a large flat plate

To explain the increase in noise when a jet impinges on a large flat plate, mean velocity, turbulence intensity, and scale were measured at nominal nozzle-exit velocities of 61, 138, and 192 meters per second with the plate located 7.1 nozzle-exit diameters from the nozzle. The maximum turbulence intensities in free and impinging jets were about the same; however, the integral length scale near the plate surface was only about one-half the free jet scale. The measured intensities and length scales, in conjunction with a contemporary theory of aerodynamic noise, provided a good explanation for the observed increase in noise associated with the impinging jet. An increase in the volume of highly turbulent flow could be the principal reason for the increase in noise.

Boldman, D. R.↗

NASA NTRS1977

Methods for measuring plating thicknesses on TAB lead frames

Plating three layer tape lead frames, used for tape automated bonding, offers a challenge to the electroplater because of nonuniform topography. Each lead frame contains large (typically .05 x. .05 inch) flat test pads located around the perimeter of the frame. These test pads are electrically connected to the bondable lead frame fingers which extend into an area in the center of the frame called the feature hole. The feature hole exposes these fingers to plating on all sides, while the test pads are exposed on only one side. In addition, the fingers are small in cross section (typically .003 x .0015 inches). Recent thickness measurements indicate that plating around the lead frame fingers is nearly twice as thick as that on test pad areas. Procedures and equipment were developed for measuring the thickness of the deposited material. Discussion was centered on the data obtained using the various measurement techniques and equipment.

Hagen, M. P.↗

NASA NTRS1978

Noise transmission through plates into an enclosure

An analytical model is presented to predict noise transmission through elastic plates into a hard-walled rectangular cavity at low frequencies, that is, frequencies up through the first few plate and cavity natural frequencies. One or several nonoverlapping and independently vibrating panels are considered. The effects on noise transmission of different external-pressure excitations, plate boundary conditions, fluid parameters, structural parameters, and geometrical parameters were investigated.

Mcdonald, W. B.↗

NASA NTRS1977

Forced motion of an initially stressed rectangular plate - An elasticity solution

An initially stressed rectangular plate is subjected to a transverse, time dependent load. The initial stress field is constant and parallel to two of the plate edges. The transverse load is uniformly distributed over a rectangular area, the sides of which are parallel to the sides of the plate. The problem is formulated within the framework of classical, three-dimensional elasticity theory, and an exact solution is obtained in series form. The case of static stability under pre-stress is also considered.

Reismann, H.↗

NASA NTRS1978

Continuum models for beam-like and plate-like lattice structures

A simple, rational approach is presented for developing continuum models for large repetitive beam-like and plate-like lattices with arbitrary configurations subjected to static, thermal and dynamic loadings. The continuum models for these structures are shear flexible beams and plates. They account for local effects in the repeating element of the actual structure and are characterized by their thermoelastic strain and kinetic energies from which the equations of motion and constitutive relations can be derived. The procedure for developing the expressions for thermoelastic strain and kinetic energies of the continuum involves introducing basic assumptions regarding the variation of the temperature, displacement and strain components in one or two directions (for plate-like and beam-like lattices) and obtaining effective thermoelastic and dynamic coefficients of the continuum in terms of material properties and geometry of the original lattice structure. The high accuracy of the continuum models developed is demonstrated by means of numerical examples.

Noor, A. K.↗

NASA NTRS1978

Polarization by a tilted absorbing glass plate

Formulas for the response of an optical detector to the transmitted component of a tilted absorbing glass plate are derived in terms of the angle of incidence, the thickness of the plate, and the absorption coefficient and index of refraction of the glass. Numerical results are discussed for detectors of various sizes compared to the width of the incident beam and thickness of the plate.

Walraven, R. L.↗

NASA NTRS1979

Efficient dichroic plate for microwaves

Signal separator for dual-frequency antennas has interlaced crossed slots, or dipole elements. Plate reflects or transmits more efficiently than conventionally-designed microwave dichroic plates in which elements are not interlaced. Interlaced plate also increases bandwidth of dual-frequency antenna in which it is used.

Wise, T. E.↗

NASA NTRS1978

Method of obtaining intensified image from developed photographic films and plates

A method is explained of obtaining intensified images from silver images on developed photographic films and plates. The steps involve converting silver of the developed film or plate to a radioactive compound by treatment with an aqueous alkaline solution of an organo-S35 compound; placing the treated film or plate in direct contact with a receiver film which is then exposed by radiation from the activated film; and developing and fixing the resulting intensified image on the receiver film.

Askins, B. S.↗

NASA NTRS1978

Experimental investigation of effects of jet decay rate on jet-induced pressures on a flat plate: Tabulated data

Tabular data are presented for an experimental study of the effects of jet decay rate on the jet-induced pressure distribution on a flat plate for a single jet issuing at right angle to the flat plate into a uniform crossflow. The data are presented in four sections: (1) presents the static nozzle calibration data; (2) lists the plate surface static pressure data and integrated loads; (3) lists the jet centerline trajectory data; and (4) lists the centerline dynamic pressure data.

Kuhlman, J. M.↗

NASA NTRS1979

Industrial potential, uses, and performance of sputtered and ion plated films

The sputtering and ion plating technology is reviewed in terms of their potential, uses and performance. It offers the greatest flexibility in coating preparation, since coatings can be tailored in any preferred chemical combination, and graded type interfaces (ceramic to metal seals) can be formed. Sputtered and ion plated film characteristics such as the degree of adherence, coherence and morphological growth which contribute to film performance and reliability are described and illustrated as used in practice. It is concluded that the potential future of sputtered and ion plated films for industrial applications will depend primarily upon greater comprehension of materials selection, possible elimination of restrictions for coating/substrate combinations and the awareness of utilizing the proper deposition parameters.

Spalvins, T.↗

NASA NTRS1978

Effects of debonds on the strength of composite plates

The effect of debonds on composite structures under compressive loads is investigated in this paper. Because of the inclusion of debonds, unsymmetric laminated rectangular plates are considered. The resulting bending-extension coupling is included and is shown to be quite significant for thin laminates typical of debonded regions. The solution technique is based on the Theorem of Minimum Potential Energy; and both simply supported and clamped boundaries are considered. The need to include transverse shear deformation in the analysis is documented. Also, the range of applicability of the reduced stiffness matrix technique for such plates is stated. The consideration of non-rectangular boundaries, as would normally occur for debonded regions, has been included through a finite element study. Using the results of this study, an effective laminated plate theory for irregularly shaped debonded regions is proposed.

Daugherty, R. L.↗

NASA NTRS1979

LDEF transverse flat plate heat pipe experiment /S1005/

The paper describes the Transverse Flat Plate Heat Pipe Experiment. A transverse flat plate heat pipe is a thermal control device that serves the dual function of temperature control and mounting base for electronic equipment. In its ultimate application, the pipe would be a lightweight structure member that could be configured in a platform or enclosure and provide temperature control for large space structures, flight experiments, equipment, etc. The objective of the LDEF flight experiment is to evaluate the zero-g performance of a number of transverse flat plate heat pipe modules. Performance will include: (1) the pipes transport capability, (2) temperature drop, and (3) ability to maintain temperature over varying duty cycles and environments. Performance degradation, if any, will be monitored over the length of the LDEF mission. This information is necessary if heat pipes are to be considered for system designs where they offer benefits not available with other thermal control techniques, such as minimum weight penalty, long-life heat pipe/structural members.

Robinson, G. A., Jr.↗

NASA NTRS1979

Vapour phase details in the oscillatory combustion of propellants A porous plate analogue

A perforated porous plate burner is designed to scale up the vapor phase details in composite propellant combustion. A fuel vapor is passed through the pores and an oxidizer vapor is passed through the discrete perforations drilled in the plate. Discussion of the scale modeling of the vapor phase details in oscillatory combustion of composite propellants leads to the following conclusions: (1) the concept of a perforated porous plate analog for the composite propellant vapor phase combustion appears to be valid during oscillatory combustion as well; (2) the flame standoff distance can be conveniently determined with motion picture photography; (3) the flame standoff distance varies with the flow velocity during oscillatory combustion much the same way as during time-independent combustion; and (4) the overall structure of the combustion zone (flame) does not appear to vary too much from its time-independent structure during oscillatory combustion

Ramohalli, K.↗

NASA NTRS1978

The Pd2Si - /Pd/ - Ni - solder plated metallization system for silicon solar cells

The rationale and application of a plated metal system, Pd2Si Pd - Ni - solder, is presented. This metallization system is particularly useful on shallow p-n junction solar cells. The advantages of such plated solar cell contacts are discussed. A process sequence for applying the metallization system is outlined. A specific example is presented, including chemical plating solution formulations and detailed process step descriptions. Electrical test data for solar cells metallized with the palladium-nickel-solder system are provided.

Coleman, M. G.↗

NASA NTRS1980

Computational models for the nonlinear analysis of reinforced concrete plates

A finite element computational model for the nonlinear analysis of reinforced concrete solid, stiffened and cellular plates is briefly outlined. Typically, Mindlin elements are used to model the plates whereas eccentric Timoshenko elements are adopted to represent the beams. The layering technique, common in the analysis of reinforced concrete flexural systems, is incorporated in the model. The proposed model provides an inexpensive and reasonably accurate approach which can be extended for use with voided plates.

Hinton, E.↗

NASA NTRS1979

A high performance porous flat-plate solar collector

A solar collector employing a porous matrix as a solar absorber and heat exchanger is presented and its application in solar air heaters is discussed. The collector is composed of a metallic matrix with a porous surface which acts as a large set of cavity radiators; cold air flows through the matrix plate and exchanges heat with the thermally stratified layers of the matrix. A steady-state thermal analysis of the collector is used to determine collector temperature distributions for the cases of an opaque surface matrix with total absorption of solar energy at the surface, and a diathermanous matrix with successive solar energy absorption at each depth. The theoretical performance of the porous flat plate collector is shown to exceed greatly that of a solid flat plate collector using air as the working medium for any given set of operational conditions. An experimental collector constructed using commercially available, low cost steel wool as the matrix has been found to have thermal efficiencies from 73 to 86%.

Lansing, F. L.↗

NASA NTRS1980

Crack problems for a rectangular plate and an infinite strip

The general plane problem for an infinite strip containing multiple cracks perpendicular to its boundaries is considered. The problem is reduced to a system of singular integral equations. Two specific problems of practical interest are then studied in detail. The first problem explores the interaction effect of multiple edge cracks in a plate or beam under tension or bending. The second problem is that of a rectangular plate containing an arbitrarily oriented crack in the plane of symmetry. Particular emphasis is placed on the problem of a plate containing an edge crack and subjected to concentrated forces.

Civelek, M. B.↗

NASA NTRS1978

A correlation method to predict the surface pressure distribution on an infinite plate from which a jet is issuing

A correlation method to predict pressures induced on an infinite plate by a jet issuing from the plate into a subsonic free stream was developed. The complete method consists of an analytical method which models the blockage and entrainment properties of the jet and a correlation which accounts for the effects of separation. The method was developed for jet velocity ratios up to ten and for radial distances up to five diameters from the jet. Correlation curves and data comparisons are presented for jets issuing normally from a flat plate with velocity ratios one to twelve. Also, a list of references which deal with jets in a crossflow is presented.

Perkins, S. C., Jr.↗