Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Performance Ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Pressure distribution data from tests of 2.29 M (7.5 feet) span EET high-lift transport aircraft model in the Ames 12-foot pressure tunnel

A high-lift transport aircraft model equipped with full-span leading-edge slat and part-span double-slotted trailing-edge flap was tested in the Ames 12-ft pressure tunnel to determine the low-speed performance characteristics of a representative high-aspect-ratio supercritical wing. These tests were performed in support of the Energy Efficient Transport (EET) program which is one element of the Aircraft Energy Efficiency (ACEE) project. Static longitudinal forces and moments and chordwise pressure distributions at three spanwise stations were measured for cruise, climb, two take-off flap, and two landing flap wing configurations. The tabulated and plotted pressure distribution data is presented without analysis or discussion.

Kjelgaard, S. O.↗
NASA NTRS1999

Rocket-in-a-Duct Performance Analysis

An axisymmetric, 110 N class, rocket configured with a free expansion between the rocket nozzle and a surrounding duct was tested in an altitude simulation facility. The propellants were gaseous hydrogen and gaseous oxygen and the hardware consisted of a heat sink type copper rocket firing through copper ducts of various diameters and lengths. A secondary flow of nitrogen was introduced at the blind end of the duct to mix with the primary rocket mass flow in the duct. This flow was in the range of 0 to 10% of the primary massflow and its effect on nozzle performance was measured. The random measurement errors on thrust and massflow were within +/-1%. One dimensional equilibrium calculations were used to establish the possible theoretical performance of these rocket-in-a-duct nozzles. Although the scale of these tests was small, they simulated the relevant flow expansion physics at a modest experimental cost. Test results indicated that lower performance was obtained at higher free expansion area ratios and longer ducts, while, higher performance was obtained with the addition of secondary flow. There was a discernable peak in specific impulse efficiency at 4% secondary flow. The small scale of these tests resulted in low performance efficiencies, but prior numerical modeling of larger rocket-in-a-duct engines predicted performance that was comparable to that of optimized rocket nozzles. This remains to be proven in large-scale, rocket-in-a-duct tests.

Schneider, Steven J.↗
NASA NTRS2012

Performance and Loads Correlation of a UH-60A Slowed Rotor at High Advance Ratios

Measured data from the slowed rotor part of the 2010 UH-60A Airloads Rotor test in the NASA Ames 40- by 80- Foot Wind Tunnel are compared with CAMRAD II calculations. The emphasis in this initial study is to correlate overall trends. This analytical effort considers advance ratios from 0.3 to 1.0, with the rotor rotational speed at 40%NR. The rotor performance parameters considered are the thrust coefficient, power coefficient, L/DE, torque, and H-force. The blade loads considered are the half peak-to-peak, mid-span and outboard torsion, flatwise, and chordwise moments, and the pitch link load. For advance ratios . 0.7, the overall trends for the performance and loads (excluding the pitch link load) could be captured, but with substantial overprediction or underprediction. The correlation gradually deteriorates as the advance ratio is increased and for advance ratios . 0.8 there is no correlation. The pitch link load correlation is not good. There is considerable scope for improvement in the prediction of the blade loads. Considering the modeling complexity associated with the unconventional operating condition under consideration, the current predictive ability to capture overall trends is encouraging.

Kottapalli, Sesi B.↗
NASA NTRS1973

Pioneer Venus mechanical roots pump test and evaluation

A mechanical pump for use with the Pioneer-Venus probe mass spectrometer inlet system was obtained, and a limited performance testing program, including ultimate/compression ratio tests and throughput tests at three different pump speeds, was performed. Considerable operating experience with the pump was obtained over approximately 200 hours of running. The test results show general agreement with pump specifications.

Thomas, N. C.↗
NASA NTRS1990

Single-pass memory system evaluation for multiprogramming workloads

Modern memory systems are composed of levels of cache memories, a virtual memory system, and a backing store. Varying more than a few design parameters and measuring the performance of such systems has traditionally be constrained by the high cost of simulation. Models of cache performance recently introduced reduce the cost simulation but at the expense of accuracy of performance prediction. Stack-based methods predict performance accurately using one pass over the trace for all cache sizes, but these techniques have been limited to fully-associative organizations. This paper presents a stack-based method of evaluating the performance of cache memories using a recurrence/conflict model for the miss ratio. Unlike previous work, the performance of realistic cache designs, such as direct-mapped caches, are predicted by the method. The method also includes a new approach to the problem of the effects of multiprogramming. This new technique separates the characteristics of the individual program from that of the workload. The recurrence/conflict method is shown to be practical, general, and powerful by comparing its performance to that of a popular traditional cache simulator. The authors expect that the availability of such a tool will have a large impact on future architectural studies of memory systems.

Conte, Thomas M.↗
NASA NTRS1975

An investigation of several NACA 1-series inlets at Mach numbers from 0.4 to 1.29 for mass flow ratios near 1.0

An investigation to determine the performance of eight NACA 1-series inlets at massflow ratios near 1.0 was conducted in the Langley 16-foot transonic tunnel. The inlet diameter ratios (ratio of inlet diameter to maximum diameter) were 0.85 and 0.89 for an inlet length ratio (ratio of inlet length to maximum diameter) of 1.0. Inlet lip radius varied from 0.061 cm to 0.251 cm, and internal contraction area ratio (ratio of inlet area to throat area) varied from 1.006 to 1.201. Reynolds number based on model maximum diameter ranged from 3,600,000 at a Mach number of 400,000 to 5,900,000 at a Mach number of 1.29. The results indicate that nearly uniform pressure distributions on a given inlet were obtained over a limited range of mass-flow ratios and Mach numbers. When inlet lip thickness was increased by means of lip radius or contraction ratio, the inlet critical Mach number decreased. Drag-divergence Mach number inferred from forebody pressure integrations was above 0.94 for most of the inlets tested.

Re, R. J.↗
NASA NTRS2017

Nonlinear Large Deflection Theory with Modified Aeroelastic Lifting Line Aerodynamics for a High Aspect Ratio Flexible Wing

This paper investigates the effect of nonlinear large deflection bending on the aerodynamic performance of a high aspect ratio flexible wing. A set of nonlinear static aeroelastic equations are derived for the large bending deflection of a high aspect ratio wing structure. An analysis is conducted to compare the nonlinear bending theory with the linear bending theory. The results show that the nonlinear bending theory is length-preserving whereas the linear bending theory causes a non-physical effect of lengthening the wing structure under the no axial load condition. A modified lifting line theory is developed to compute the lift and drag coefficients of a wing structure undergoing a large bending deflection. The lift and drag coefficients are more accurately estimated by the nonlinear bending theory due to its length-preserving property. The nonlinear bending theory yields lower lift and span efficiency than the linear bending theory. A coupled aerodynamic-nonlinear finite element model is developed to implement the nonlinear bending theory for a Common Research Model (CRM) flexible wing wind tunnel model to be tested in the University of Washington Aeronautical Laboratory (UWAL). The structural stiffness of the model is designed to give about 10% wing tip deflection which is large enough that could cause the nonlinear deflection effect to become significant. The computational results show that the nonlinear bending theory yields slightly less lift than the linear bending theory for this wind tunnel model. As a result, the linear bending theory is deemed adequate for the CRM wind tunnel model.

Aeroelasticity↗
NASA NTRS2006

Fan Performance From Duct Rake Instrumentation on a 1.294 Pressure Ratio, 725 ft/sec Tip Speed Turbofan Simulator Using Vaned Passage Casing Treatment

A 1.294 pressure ratio, 725 ft/sec tip speed, variable pitch low noise fan was designed and tested in the NASA Glenn 9- by 15-foot Wind Tunnel. The design included a casing treatment that used recirculation to extend the fan stall line and provide an acceptable operating range. Overall aerodynamic experimental results are presented for this low tip speed, low noise fan without casing treatment as well as using several variants of the casing treatment that moved the air extraction and insertion axial locations. Measurements were made to assess effects on performance, operability, and noise. An unusual instability was discovered near the design operating line and is documented in the fan operating range. Measurements were made to compare stall margin improvements as well as measure the performance impact of the casing treatments. Experimental results in the presence of simulated inlet distortion, via screens, are presented for the baseline and recirculation casing treatment configurations. Estimates are made for the quantity of recirculation weight flow based on limited instrumentation in the recirculation system along with discussion of results and conclusions

Fite, E. Brian↗
NASA NTRS1949

Performance of conical jet nozzles in terms of flow and velocity coefficients

Performance characteristics of conical jet nozzles were determined in an investigation covering a range of pressure ratios from 1.0 to 2.8, cone half-angles from 5 degrees to 90 degrees, and outlet-inlet diameter ratios from 0.50 to 0.91. All nozzles investigated had an inlet diameter of 5 inches. The flow coefficients of the conical nozzles investigated were dependent on the cone half-angle, outlet-inlet diameter ratio, and pressure ratio. The velocity coefficients were essentially constant at pressure ratios below the critical. For increasing pressures above critical pressure ratio, there was a small decrease in velocity coefficient that was dependent on pressure ratio and independent of cone half-angle and outlet-inlet diameter ratio. Therefore the variation in performance (air flow and thrust) of several nozzles, selected for the same performance at a particular design condition, was proportional to the ratio of their flow coefficients.

Grey, Ralph E↗
NASA NTRS1980

Performance of code division multiple access systems

The performance of code division multiple-access (CDMA) systems is determined using direct sequence spectral spreading. Under relatively ideal conditions, the degradation in system performance as a function of the number of users is shown to have a threshold effect. This basic limitation in the number of users of the system is further limited if the powers are unequal. For two users, system performance as a function of their power ratio also has a threshold effect. System performance as a function of the amount of spectral spreading is determined. The performance of both coded and uncoded systems is predicted.

Weber, C. L.↗
NASA NTRS1985

Tests of Low-Concentration-Ratio Photovoltaic Elements

Report describes performance measurements on elements of low-concentrationratio solar arrays (LCRSA's) employing silicon and gallium arsenide photovoltaic cells. Measurements intended to verify predictions of performance based on mathematical models. Measured and predicted values found to agree closely for both normal and off-normal pointing of array toward Sun.

Mills, M. W.↗
DOE OSTI2021

Numerical study to predict the effect of surface roughness on the thermal and hydraulic performance of additively manufactured heat exchangers

Heat exchangers are used in many industries to transfer thermal energy between two or more objects with an associated thermal and hydraulic performance indicated by thermal effectiveness and pressure drop respectively. Many investigations have aimed to enhance the thermal effectiveness of heat exchangers by introducing turbulent flow inducers that increase the heat transfer rate at the expense of increasing pressure drop. Flow inducers like surface roughness can be controlled with advanced manufacturing methods like additive manufacturing for heat exchanger production. Selecting and manufacturing an optimal surface roughness for heat exchangers requires a more comprehensive approach that accounts for the surface roughness effect on the thermal and hydraulic performance of a sample. Since fabricating samples with additive manufacturing to a desired surface roughness can be an extensive experimental process, this study will fundamentally investigate the effect of surface roughness on the thermal and velocity boundary layers for various surface roughness profiles with physics-based computational modeling. To accurately model the surface roughness effect on thermohydraulic performance, correlations like roughness ratio, friction factor, and Nusselt number are investigated. This study expects to indicate correlations for different flow regimes which can successfully predict the effect of surface roughness on thermohydraulic performance. Results generated from modeling surface roughness effect with unique correlations are then compared to experimental data obtained from literature for validation. The results of this study will provide insight to understand the thermal fluid physics associated with surface roughness and design guidelines for heat exchangers produced with additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microwave-assisted pyrolysis of liquid hydrocarbons using iron-based alumina catalysts obtained by solution combustion synthesis: The effect of synthesis parameters

The microwave-absorbing and catalytic properties of iron-based alumina (FeAl x O y ) materials have enabled their use as catalysts for the microwave-assisted generation of hydrogen and carbon via pyrolysis of hydrocarbons. Solution combustion synthesis (SCS) is a promising method to fabricate these materials, but the pyrolysis performance still needs to be improved. The present work investigated how altering the SCS parameters affects the pyrolysis of diesel fuel, gasoline, and crude oil. Two fuels (citric acid and glycine), four Fe:Al molar ratios, and two heating modes (hotplate and furnace) were tested. Fe/γ-Al 2 O 3 and Fe/β-SiC catalysts were prepared via incipient wetness impregnation for comparison. Among the three fossil fuels tested, diesel fuel yielded the highest amounts of H 2 and least amounts of CO x . The choice of fuel for the SCS process and the Fe/Al ratio strongly affected pyrolysis performance as they influence properties important for both catalysis and microwave absorption. The use of glycine resulted in catalysts that exhibited high H 2 yield and low CO 2 generation, which is explained by the revealed structural differences. The increase in the Fe:Al molar ratio accelerated microwave heating by adding more magnetic loss but also increased the amount of CO x . When the optimal SCS parameters were used, FeAl x O y catalysts outperformed Fe/γ-Al 2 O 3 and Fe/β-SiC. The high H 2 generation efficiency of the SCS catalysts is explained by their enhanced microwave-absorption properties. Scanning electron microscopy and energy dispersive X-ray spectroscopy revealed the formation of large-diameter CNTs via the tip-growth mechanism. The regeneration of SCS catalysts was demonstrated via the Boudouard reaction.

Carbon nanotubes↗
NASA NTRS2022

Time-Series Ratio Algorithm for Nisar Soil Moisture Retrieval

The NASA ISRO Synthetic Aperture Radar (NISAR) mission is currently under development and will provide global L-band radar observations that will be helpful for various soil moisture applications. The final NISAR soil moisture product will have 200m spatial resolution with 12-day exact revisit time. A time-series ratio algorithm was implemented using NISAR simulated UAVSAR data collected during the SMAPVEX12 field experiment. In this paper, the performance of the time series ratio algorithm was assessed using in situ observations. Performance of the soil moisture retrieval algorithm was also assessed for dual polarization and quad-polarization observations modes.

Jeonghwan Park↗
NASA NTRS2020

Static Loads Testing of a High Aspect Ratio Tow-Steered Wingbox

Static loads testing was performed on a 39-foot, high-aspect-ratio wingbox comprising carbon fiber tow-steered wing skins that were tailored for aircraft fuel efficiency under aeroelastic loads. The test article was designated the Passive Aeroelastic Tailored (PAT) wing. To date, the PAT wing, which has an aspect ratio of 13.5, is the largest wingbox designed and built to employ variably oriented carbon fibers along the span of the wing. During testing, distributed point loads were applied to the wingbox to simulate both -1g and 2.5g maneuver loads. To determine the wingbox’s flexural axis location, individual point loads were applied. The global response of the wing (displacement and rotation measurements) showed similar trends compared to the finite element model predictions, though discrepancies of up to 17% were observed when comparing actual values between model and test. It was concluded that the boundary conditions and nonstructural features of the wingbox were the likely cause of the inconsistencies. The local response of the wingbox (strain measurements), which was much less affected by factors unrelated to tow-steering, exhibited good agreement with the model predictions, validating the modelling techniques employed for tow-steered composites.

Tow-steered composites↗
DOE OSTI2026

Optimized Gear Selection to Maximize Energy Savings in Electric Traction Drives for Medium and Heavy Duty Vehicles

Multi‑gear transmission systems are commonly used in electric traction drives for medium and heavy‑duty vehicles, while most passenger‑vehicle electric drivetrains rely on a single fixed ratio to reduce cost, weight, and complexity. Using multiple gear ratios can enable downsizing of the motor and inverter while still meeting performance requirements. Additionally, appropriately chosen ratios allow the motor to operate more frequently in high‑efficiency regions, improving overall energy usage and reducing operating costs over the drive cycle. This paper presents a systematic approach for selecting optimal gear ratios for electric drive systems. A neural‑network model is first developed to represent motor losses across the full torque–speed range using data generated from finite element analysis. This model enables fast, accurate evaluation of motor efficiency under varying operating conditions. A genetic‑algorithm‑based optimization framework is then applied to identify gear ratios that maximize energy cost savings over the drive cycle, with the resulting optimal ratios stored for real‑time implementation.

Gadiyar, Nishanth [ORNL] (ORCID:0000000348267524)↗
NASA NTRS1977

Evaluation of a low aspect ratio small axial compressor stage, volume 1

A program was conducted to evaluate the effects of scaling, tip clearance, and IGV reset on the performance of a low aspect ratio compressor stage. Stage design was obtained by scaling an existing single stage compressor by a linear factor of 0.304. The design objective was to maintain the meanline velocity field of the base machine in the smaller size. Adjustments were made to account for predicted blockage differences and to chord lengths and airfoil edge radii to obtain reasonable blade geometries. Meanline velocity diagrams of the base stage were not maintained at the scaled size. At design speed and flowrate the scaled stage achieved a pressure ratio of 1.423, adiabatic efficiency of 0.822, and surge margin of 18.5%. The corresponding performance parameters for the base stage were 1.480, 0.872, and 25.2%, respectively. The base stage demonstrated a peak efficiency at design speed of 0.872; the scaled stage achieved a level of 0.838. When the scaled stage rotor and stator tip clearances were doubled, the stage achieved a pressure ratio of 1.413, efficiency of 0.799, and surge margin of 16.0% at the design flowrate. The peak stage efficiency at design speed was 0.825 with the increased clearance. Increased prewhirl lowered the stage pressure ratio as expected. Stage efficiency was maintained with ten degrees of increased prewhirl and then decreased substantially with ten additional degrees of reset.

Sawyer, C. W., III↗