Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PAST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Cumulative frequency distribution of past species extinctions

Analysis of Sepkoski's compendium of the time ranges of 30,000+ taxa yields a mean duration of 28.4 ma for genera of fossil invertebrates. This converts to an average extinction rate of 3.5 percent per million years or about one percent every 286,000 years. Using survivorship techniques, these estimates can be converted to the species level, yielding a Phanerozoic average of one percent species extinction every 40,000 years. Variation in extinction rates through time is far greater than the null expectation of a homogeneous birth-death model and this reflects the well-known episodicity of extinction ranging from a few large mass extinctions to so-called background extinction. The observed variation in rates can be used to construct a cumulative frequency distribution of extinction intensity, and this distribution, in the form of a kill curve for species, shows the expected waiting times between extinction events of a given intensity. The kill curve is an average description of the extinction events of a given intensity. The kill curve is an average description of the extinction record and does not imply any cause or causes of extinction. The kill curve shows, among other things, that only about five percent of total species extinctions in the Phanerozoic were involved in the five largest mass extinctions. The other 95 percent were distributed among large and small events not normally called mass extinctions. As an exploration of the possibly absurd proposition that most past extinctions were produced by the effects of large-body impact, the kill curve for species was mapped on the comparable distribution for comet and asteroid impacts. The result is a curve predicting the species kill for a given size of impacting object (expressed as crater size). The results are reasonable in that impacts producing craters less than 30 km (diameter) cause negligible extinction but those producing craters 100-150 km (diameter) cause extinction of species in the range of 45-60 percent.

Raup, D. M.↗

Iron Moessbauer spectroscopy: Superparamagnetism in hydrothermal vents and the search for evidence of past life on Mars

In view of the demonstrated value of Iron Moessbauer Spectroscopy (FeMS) in the study of extraterrestrial iron and the fact that, after silicon and oxygen, iron is the most abundant element on the surface of Mars, we proposed, and have under development, a backscatter Moessbauer spectrometer with x ray fluorescence capability (BaMS/XRF) for use on Mars as a geophysical prospecting instrument. Specifically, we have proposed BaMS/XRF as part of the geochemistry instrumentation on NASA's Mars Environment Survey (MESUR) mission. BaMS/XRF will have applications in: (1) the study of past environments through the examination of sedimentary material; (2) the study of the contemporary Martian environment; and (3) the study of iron-containing minerals of possible biogenic origin. Development of a reference library from a geophysical point of view for putative Martian surface materials at appropriate temperatures is now underway. We carried out preliminary optical reflectance and FeMS measurements on mineral products (iron oxyhydroxides) of deep-sea hydrothermal activity. Various aspects of this investigation are presented.

Agresti, David G.↗

MHD flow past an obstacle - Large-scale flow in the magnetosheath

As a step to the study of the large-scale flow in the magnetosheath, the MHD flow past an obstacle is investigated. A time asymptotic method is used to obtain 3D steady-state solutions. The results indicate the formation of a depletion layer near the obstacle due to the increase of the magnetic field. Along the earth-sun line the plasma density increases first and then decreases from the post bow shock to the magnetopause. The local density maximum in front of the magnetopause may correspond to what was recently observed. When the interplanetary magnetic field direction is tilted from the solar wind flow, the IMF influences the shape of the bow shock as well as the location of the stagnation point at the magnetopause in a way consistent with observation. In addition, the results show the existence of a magnetosheath current in the post parallel-shock region.

Wu, C. C.↗

Hypersonic rarefied flow past spheres including wake structure

Results of a numerical study using the direct simulation Monte Carlo method are presented for hypersonic rarefied flow past spheres. The flow conditions considered are those corresponding to low density wind tunnel test conditions. The set of the experimental conditions for the calculations encompasses the transitional to near-continuum flow regimes. Comparison of the calculated drag with experimental results shows good agreement to well within the experimental error. Particular attention is focused on the wake structure. Calculations show that the wake is very rarefied with considerable thermal nonequilibrium for all the cases considered. No flow separation is observed in the wake for the near-continuum case where a vortex has been predicted by Navier-Stokes type calculations.

Dogra, Virendra K.↗

The inviscid stability of supersonic flow past heated or cooled axisymmetric bodies

The inviscid, linear, nonaxisymmetric, temporal stability of the boundary layer associated with the supersonic flow past axisymmetric bodies (with particular emphasis on long thin, straight circular cylinders), subject to heated or cooled wall conditions is investigated. The eigenvalue problem is computed in some detail for a particular Mach number or 3.8, revealing that the effect of curvature and the choice of wall conditions both have a significant effect on the stability of the flow. Both the asymptotic, large azimuthal wavenumber solution and the asymptotic, far downstream solution are obtained for the stability analysis and compared with numerical results. Additionally, asymptotic analyses valid for large radii of curvature with cooled/heated wall conditions are presented. In general, important differences were found to exist between the wall temperature conditions imposed and the adiabatic wall conditions considered previously.

Shaw, Stephen J.↗

Viscous simulation method for unsteady flows past multicomponent configurations

The present algorithm for the numerical simulation of flows about complex configurations (whose multiple and nonsimilar components have arbitraty geometries) employs a hybridization of the domain decomposition techniques for grid generation as well as to reduce computer-memory requirements. A fully vectorized, finite-volume, upwind-biased, approximately factored multigrid method is used to solve 3D Reynolds-averaged unsteady and compressible Navier-Stokes equations simulating supersonic flows past an ogive-nose-cylinder near or within a cavity. The time-averaged surface pressures obtained compare favorably with the wind tunnel data.

Fouladi, Kamran↗

Viscous flow past a nacelle isolated and in proximity of a flat plate

Linearized-theory design procedures have proven to be useful in preliminary design stages of supersonic aircraft configurations. These procedures are impaired, however, by their inability to account for certain nonlinear effects inherent in complicated flows. The present computations are aimed at providing necessary information for correction and improvement of a particular linearized design method. Three-dimensional, viscous, supersonic flows past nacelle and nacelle-flat plate configurations are investigated. The thin-layer Navier-Stokes equations are solved using an implicit, upwind-biased, finite-volume method. A hybrid domain decomposition technique is utilized to ease the grid generation task. Computations were made for an unit Reynolds number of 2.0 million per foot and Freestream Mach numbers of 1.6, 2.0, and 2.3.

Fouladi, Kamran↗

Computing high-speed flows past an oscillating cylinder near a vertical wall

A computational method to simulate unsteady flows involving moving rigid boundaries and interference has been developed. The method is used to solve inviscid equations governing the fluid flow and the dynamic equations governing the motion of rigid bodies. A second-order accurate, upwind-biased, and alterating-direction-implicit method is used to solve the governing equations of the flow. A kinematic domain decomposition (KDD) procedure is extended to treat 3D problems with a high degree of accuracy and generality. The method under consideration is applied to both transonic and supertransonic flows. Both cases involve flow past a cylinder which is forced to pitch sinusoidally near a vertical wall. Benefits of the proposed approach include accurate calculation of the flow around 3D moving multiple bodies with interference; reduction of a numerical error; in particular, the dispersion error which strongly affects wave propagation; and minimization of the phase error which is accumulated according to the time advance procedure.

Yen, Guan-Wei↗

Computational analysis of hypersonic flows past elliptic-cone waveriders

A comprehensive study for the inviscid numerical calculation of the hypersonic flow past a class of elliptic-cone derived waveriders is presented. The theoretical background associated with hypersonic small-disturbance theory (HSDT) is reviewed. Several approximation formulas for the waverider compression surface are established. A CFD algorithm is used to calculate flow fields for the on-design case and a variety of off-design cases. The results are compared with HSDT, experiment, and other available CFD results. For the waverider shape used in previous investigations, the bow shock for the on-design condition stands off from the leading-edge tip of the waverider. It was found that this occurs because the tip was too thick according to the approximating shape formula that was used to describe the compression surface. When this was corrected, the bow shock became closer to attached as it should be. At Mach numbers greater than the design condition, a lambda-shock configuration develops near the tip of the compression surface. At negative angles of attack, other complicated shock patterns occur near the leading-edge tip. These heretofore unknown flow patterns show the power and utility of CFD for investigating novel hypersonic configurations such as waveriders.

Yoon, Bok-Hyun↗

Navier-Stokes calculation of transonic flow past the NTF 65-deg delta wing

Viscous flow past a wind tunnel model of a 65-degree swept angle Delta wing at transonic speeds is being studied. The model was tested in the 8-foot cryogenic transonic wind tunnel at the National Transonic Facility. Aerodynamic forces and wing surface pressure data were obtained at various angles of attack, Mach numbers, and Reynold's numbers for four different leading edges of the wing. The objectives of the present investigation are: (1) to perform numerical modeling of the flow around the wing; (2) to validate the experimental data with a Navier-Stokes computational fluid dynamics code and vice versa; (3) to investigate the effects of the sting mount of the wing; (4) to evaluate the effects of leading edge radius on the flow; and (5) to explain the Reynold's number effect as indicated by the test data. Several computer programs were developed to define the surfaces of the wing, the four leading edges, and the sting mount. Based on these geometric databases, the surface grids of a single-block computational domain was generated interactively on the IRIS workstation using the GRIDGEN2D module of GRIDGEN. To refine the grids and to avoid excessive loss of grid points due to collapsed edges, a 9-block computational domain containing approximately 750,000 grid points was developed with the GRIDBLOCK module to replace the single-block grid.

Wu, Chivey↗

The semi-discrete Galerkin finite element modelling of compressible viscous flow past an airfoil

A method is developed to solve the two-dimensional, steady, compressible, turbulent boundary-layer equations and is coupled to an existing Euler solver for attached transonic airfoil analysis problems. The boundary-layer formulation utilizes the semi-discrete Galerkin (SDG) method to model the spatial variable normal to the surface with linear finite elements and the time-like variable with finite differences. A Dorodnitsyn transformed system of equations is used to bound the infinite spatial domain thereby permitting the use of a uniform finite element grid which provides high resolution near the wall and automatically follows boundary-layer growth. The second-order accurate Crank-Nicholson scheme is applied along with a linearization method to take advantage of the parabolic nature of the boundary-layer equations and generate a non-iterative marching routine. The SDG code can be applied to any smoothly-connected airfoil shape without modification and can be coupled to any inviscid flow solver. In this analysis, a direct viscous-inviscid interaction is accomplished between the Euler and boundary-layer codes, through the application of a transpiration velocity boundary condition. Results are presented for compressible turbulent flow past NACA 0012 and RAE 2822 airfoils at various freestream Mach numbers, Reynolds numbers, and angles of attack. All results show good agreement with experiment, and the coupled code proved to be a computationally-efficient and accurate airfoil analysis tool.

Meade, Andrew J., Jr.↗

Episodes of terrestrial geologic activity during the past 260 million years - A quantitative approach

Records of major geologic events of the past about 260 Myr including: biologic extinction events, ocean-anoxic and black-shale events, major changes in sea level, major evaporite (salt) deposits, continental flood-basalt eruptions, first-order discontinuities in sea-floor spreading, and major mountain building events, have been aggregated and analyzed with moving-window and spectral techniques that facilitate recognition of clustering and possible cyclicity. Significant clustering of events suggests a model in which changes in rates and directions of sea-floor spreading ('ridge jumps') are associated with episodic rifting, volcanism, mountain building, global sea level and changes in the composition of the earth's atmosphere via the carbon cycle. The geologic data formally show a statistically significant underlying periodicity of 26.6 Myr for the Mesozoic and Cenozoic. Phase information suggests that the most recent maximum of the cycle occurred with the last 9 Myr, and may be close to the present time.

Rampino, Michael R.↗

The numerical study of 3-D flow past control surfaces

The computation of a steady 3D viscous flow past a slender delta wing-body configuration with trailing edge control surfaces is presented. For the numerical simulation, a cell centered finite volume Navier-Stokes zonal method was used and, besides the standard nonplanar zonal interfacing techniques, a new zonal capability, called a 'virtual zone', was implemented. This capability enables the end caps of the wings or flaps to be gridded and interfaced with the rest of the flowfield in a natural and straightforward manner. The computational results for 0-, 10-, and 24-deg angles-of-attack were found to agree with experimental results qualitively and quantitatively.

Chaussee, Denny S.↗

Impacts and tectonism in Earth and moon history of the past 3800 million years

The moon's surface, unlike the Earth's, displays a comparatively clear record of its past bombardment history for the last 3800 Myr, the time since active lunar tectonism under the massive premare bombardment ended. From Baldwin's (1987) tabulation of estimated ages for a representative sample of large lunar craters younger than 3800 Ma, six major cratering episodes can be discerned. These six bombardment episodes, which must have affected the Earth too, appear to match in time the six major episodes of orogenic tectonism on Earth, despite typical resolution errors of +/- 100 Myr and the great uncertainties of the two chronologies. Since more highly resolved events during the Cenozoic and Mesozoic Eras suggest the same correlation, it is possible that large impacts have influenced plate tectonics and other aspects of geologic history, perhaps by triggering flood basalt eruptions.

Stothers, Richard B.↗

Coupled atmosphere-ocean models of Titan's past

The behavior and possible past evolution of fully coupled atmosphere and ocean model of Titan are investigated. It is found that Titan's surface temperature was about 20 K cooler at 4 Gyr ago and will be about 5 K warmer 0.5 Gyr in the future. The change in solar luminosity and the conversion of oceanic CH4 to C2H6 drive the evolution of the ocean and atmosphere over time. Titan appears to have experienced a frozen epoch about 3 Gyr ago independent of whether an ocean is present or not. This finding may have important implications for understanding the inventory of Titan's volatile compounds.

Mckay, Christopher P.↗

Damping of surface pressure fluctuations in hypersonic turbulent flow past expansion corners

Surface pressure fluctuations of Mach 8 turbulent flow past a 2.5- and a 4.25-deg expansion corner maintained a Gaussian distribution but were severely attenuated by the expansion process. The pressure fluctuations did not recover to those of an equilibrium turbulent flow even though the mean pressures reached downstream inviscid values in four to six boundary-layer thicknesses. The fluctuations were convected with a velocity comparable to that on a flat plate, and they maintained their identities longer for the stronger expansion. The damping of pressure fluctuations at hypersonic Mach numbers, even by small corner angles, may be exploited in fatigue design.

Chung, Kung-Ming↗

A dynamical systems analysis of the kinematics of time-periodic vortex shedding past a circular cylinder

Computer flow simulation aided by dynamical systems analysis is used to investigate the kinematics of time-periodic vortex shedding past a two-dimensional circular cylinder in the context of the following general questions: (1) Is a dynamical systems viewpoint useful in the understanding of this and similar problems involving time-periodic shedding behind bluff bodies; and (2) Is it indeed possible, by adopting such a point of view, to complement previous analyses or to understand kinematical aspects of the vortex shedding process that somehow remained hidden in previous approaches. We argue that the answers to these questions are positive. Results are described.

Ottino, Julio M.↗

Calculation of Compressible Flows past Aerodynamic Shapes by Use of the Streamline Curvature

A simple approximate method is given for the calculation of isentropic irrotational flows past symmetrical airfoils, including mixed subsonic-supersonic flows. The method is based on the choice of suitable values for the streamline curvature in the flow field and the subsequent integration of the equations of motion. The method yields limiting solutions for potential flow. The effect of circulation is considered. A comparison of derived velocity distributions with existing results that are based on calculation to the third order in the thickness ratio indicated satisfactory agreement. The results are also presented in the form of a set of compressibility correction rules that lie between the Prandtl-Glauert rule and the von Karman-Tsien rule (approximately). The different rules correspond to different values of the local shape parameter square root sign YC sub a, in which Y is the ordinate and C sub a is the curvature at a point on an airfoil. Bodies of revolution, completely supersonic flows, and the significance of the limiting solutions for potential flow are also briefly discussed.

Perl, W↗