Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “P Reactor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Pressure Loading with In-Situ Permeability Measurement of SiC Ceramic Matrix Composite Tube

Silicon carbide fiber in a silicon carbide matrix composite (SiC-SiC) has been actively researched as a potential structural material to be used in advanced high temperature gas reactors (HTGR) and as an accident tolerant cladding material for light water reactors (LWR). This ceramic composite material demonstrates desirable properties for use in nuclear reactor core that include retention of strength from ambient to LWR and HTGR operating and accident temperatures and stability under neutron radiation. However, the ceramic composite material must be designed to meet all the necessary, application driven requirements before it could be implemented in a reactor design. As one of the requirements for a fuel cladding material, the composite has to maintain high level of impermeability as to retain fission gases throughout the fuel cycle. General Atomics (GA) had previously reported results on permeability levels obtained by CVI produced SiC-SiC composites. It has been determined that for LWR size cladding tube that is 51 mm long the permeability allocation equivalent to currently used claddings is 7.3 E-10 atm*cc/sec. With high level of attention to possible sources of leaks in a test setup, it has been demonstrated that a CVI SiC-SiC composites produced by GA can achieve a leak rate of 1 E-12 atm*cc/sec, and therefore it meets the permeability allocation for a fuel cladding. Further study showed that a particular SiC-SiC composite tube can remain impermeable after being pressure loaded well above LWR normal operating conditions. In the study done by Deck et al., hoop stress was applied to a composite tube using pressure load on the inside surface in a load-unload stepwise sequence with increasing maximum applied stress at each step and measuring permeability between steps. The tested composite comprised of 70% thickness of SiC-SiC composite which provides fracture toughness and bears a majority of the applied stress and a 30% thickness of monolithic SiC layer on the outside surface to provide an impermeable barrier. The composite remained impermeable up to internal pressure of 56 MPa which is more than 2.5 times greater than a typical pressure at the end of life in a fuel rod.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

U.S. Efforts in Support of Examinations at Fukushima Daiichi: 2019 Evaluations

Much is still not known about the end-state of core materials in each unit that was operating on March 11, 2011 at the Fukushima Daiichi Nuclear Power Station (Daiichi). Information obtained from Daiichi is required to inform Decontamination and Decommissioning (D&D) activities, improving the ability of the Tokyo Electric Power Company Holdings, Incorporated (TEPCO Holdings) to characterize potential hazards and to ensure the safety of workers involved with cleanup activities. This document, which has been updated to include Fiscal Year 2019 (FY2019) information, summarizes results from a U.S. effort to review Daiichi information and extract insights to enhance the safety of existing and future nuclear power plant designs. This U.S. effort, which was initiated in 2014 by the Department of Energy Office of Nuclear Energy (DOE-NE), is completed by a group of experts in reactor safety and plant operations that identify examination needs and evaluate recent Daiichi examination data to address these needs. Each year, annual reports are issued that document significant safety insights being obtained in areas of special emphasis. For FY2019, the areas emphasized by the expert panel include component performance, radionuclide surveys and sampling, debris end-state location, combustible gas effects, and plant operations and maintenance. In addition to reducing uncertainties related to severe accident modeling progression, these insights have and continue to be used to update guidance for severe accident prevention, mitigation, and emergency planning. Reduced uncertainties in modeling the events at Daiichi improve the realism of reactor safety evaluations that inform future D&D activities. In addition, the process established by this U.S. effort provides an example that Japan may wish to implement in future international efforts to support D&D. As emphasized in this FY2019 report, important insights are being gained from examinations of the affected units at Daiichi. Although many results from prior years have been moved to appendices, key areas of interest are highlighted in the main document. For example, larger intact components and fuel containing materials observed on the floor of the primary containment and retained on ex-vessel structures continue to be emphasized because of insights that may be gained with respect to vessel failure and ex-vessel interactions with structures and concrete. In addition, the main report presents insights gained by focused evaluations of plant data because of potential use of systems and components during severe accident conditions and alternate perspectives regarding accident progression that may be inferred from such data. The report also illustrates how systems analysis codes can be applied to reduce uncertainties about the progression of events at Daiichi and how practical insights obtained from Daiichi can be used to enhance radiation safety for the existing fleet. Recent and planned updates to systems analysis codes are also discussed. As in prior years, this report contains an appendix with a list of examination needs that was updated after U.S. experts reviewed recently obtained information from Daiichi. Additional details for higher priority, near-term, examination activities are also provided. This report also includes an appendix with a description of a website that was developed to assist U.S. experts by providing information in an archived retrievable location.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Quantitative Phenomena Identification and Ranking Table (QPIRT) for Bayesian uncertainty quantification

Propagating parameter uncertainty for a nuclear reactor system code is a challenging problem due to often non-linear system response to the numerous parameters involved and lengthy computational times; issues that compound when a statistical sampling procedure is adopted, since the code must be run many times. The number of parameters sampled must therefore be limited to as few as possible that still accurately characterize the uncertainty in the system response. A Quantitative Phenomena Identification and Ranking Table (QPIRT) was developed to accomplish this goal. The QPIRT consists of two steps: a 'Top-Down' step focusing on identifying the dominant physical phenomena controlling the system response, and a 'Bottom-Up' step which focuses on determining the correlations from those key physical phenomena that significantly contribute to the response uncertainty. The Top-Down step evaluates phenomena using the governing equations of the system code at nominal parameter values, providing a 'fast' screening step. The Bottom-Up step then analyzes the correlations and models for the phenomena identified from the Top-Down step to find which parameters to sample. The QPIRT, through the Top-Down and Bottom-Up steps thus provides a systematic approach to determining the limited set of physically relevant parameters that influence the uncertainty of the system response. This strategy was demonstrated through an application to the RELAP5-based analysis of a PWR Total Loss of main Feedwater Flow (TLOFW) accident, also known as feed and bleed' scenario, . Ultimately, this work is the first component in a larger task of building a calibrated uncertainty propagation framework. The QPIRT is an essential piece because the uncertainty of those selected parameters will be calibrated to data from both Separate and Integral Effect Tests (SETs and IETs). Therefore the system response uncertainty will incorporate the knowledge gained from the database of past large IETs. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Fischer-Tropsch Synthesis on Ceramic Monolith-Structured Catalysts

This paper reports recent research results about impact of different catalyst bed configurations on FT reaction product distribution. A CoRe/γ-alumina catalyst is prepared in bulk particle form and tested in the packed bed reactor at a size of 60 to 100 mesh. The same catalyst is ball milled and coated on a ceramic monolith support structure of channel size about 1mm. The monolith catalyst module is tested in two different ways, as a whole piece and as well-defined channels. Steady-state reaction conversion is measured at various temperatures under constant H 2 /CO feed ratio of 2 and reactor pressure of 25 bar. Detailed product analysis is performed. Significant formation of wax is evident with the packed particle bed and with the monolith catalyst that is improperly packed. By contrast, the wax formation is not detected in the liquid product by confining the reactions inside the monolith channel. This study presents an important finding about the structured catalyst/reactor system that the product distribution highly depends on the way how the structured reactor is set up. Even if the same catalyst and same reaction conditions (T, P, H 2 /oil ratio) are used, hydrodynamics (or flow conditions) inside a structured channel can have a significant impact on the product distribution.

01 COAL, LIGNITE, AND PEAT↗

Informing Reactor Aging Management by Extended Risk Methodology

This is a paper summary to be published in the proceedings of the Winter Meeting of the American Nuclear Society. It describes a method for expanding probabilistic risk assessment models to address issues associated with the management of aging nuclear power plants and the prioritization of materials degradation research.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Evaluation of the Radiological Consequences of Beyond Design Basis Accident for IRT MEPhI

The results of an analysis of the radiological consequences of a beyond design basis accident for IRT MEPhI with high-enrichment uranium fuel and conversion to IRT-3M fuel assemblies with fuel kernel based the alloy U–9% Mo in an aluminum matrix with enrichment 19.7% are presented. The beyond design basis accident is assumed to be blocking of the flow section of the coolant in FA by a foreign object. It was postulated that a single eight-tube FA will melt in this accident. The analysis is performed using approximate conservative estimates. It is shown that the effective dose for the population does not exceed the admissible level. The radiological consequences of the accident for a reactor with high- and low-enrichment fuel are almost indistinguishable.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Sodium Hydrogen Sensor and Acoustic Flow Sensor Development

This report documents the development of diffusion-type hydrogen meters (DTHMs) as part of a steam generator leak detection system (SGLDS) of sodium-cooled fast reactors (SFR) and the demonstration of the capabilities of acoustic flowmeters, including a commercial UTFM (Flexim FLUXUS F721) and an Argonne HT acoustic flowmeter running on shear-to-longitudinal mode. It also evaluates two Argonne permanent magnet flowmeters (PMFMs).

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Advanced Computational Thermal Studies and their Assessment for Supercritical-Pressure Reactors (SCRs)

The goal of this laboratory / university collaboration of coupled computational and experimental studies is the improvement of predictive methods for supercritical-pressure reactors. The general objective is to develop supporting knowledge needed of advanced computational techniques for the technology development of the concepts and their safety systems.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Neutronic Design and Analysis of the Holos-Quad Concept

HolosGen, LLC is proposing a highly innovative micro-reactor concept targeting both civilian and military applications. It consists of an advanced helium-cooled gas reactor using a turbojet-type turbine and compressor to achieve a highly condensed reactor that fits into a commercial ISO container. The Holos-Quad concept being considered for civilian applications will generate 22MWt, using four Subcritical Power Modules (SPMs) that fit into one 40-foot ISO container. It is a high-temperature gas-cooled reactor concept using TRISO fuel distributed in graphite hexagonal blocks, cooled with helium gas at 7MPa and a high outlet temperature. In FY2019, HolosGen, LLC received an ARPA-E MEITNER grant to team up with the Argonne National Laboratory (ANL) design team to demonstrate the feasibility of the Holos-Quad concept in terms of neutronics. In particular, the evaluation study of the Holos design features and alternative options for reactivity control was considered. Through these tasks, the ANL design team has been working on demonstrating the feasibility of the Holos-Quad concept in terms of neutronics to help advance the core design of the Holos-Quad. A rigorous design approach was employed for the Holos-Quad in order to ensure that the input space is fully investigated, and that the best solutions are considered. The first step of this approach consisted of properly defining the Holos-Quad design problem by identifying the competitive design objectives: its economic performance is maximized with longer lifetime and its transportability to remote locations is maximized with reduced weight. The design problem also required to identify the operational constraints (in terms of thermal hydraulics, reactivity feedback and shutdown margins) and the input parameters that could be varied. In the second step, a sensitivity analysis was performed to enable preliminary investigation of the input space to identify the correlations among input and output variables. It allowed, for instance, to find input parameters that have relatively poor impact on the core performance and that could be removed from the optimization problem to accelerate its convergence. This sensitivity analysis showed that the design problem defined is highly constrained since only 117 solutions out of 1,000 simulated cores met all the design constraints. The design optimization was performed in the third step employing a genetic algorithm to effectively explore this highly constrained input space and find global optimal solutions. More than 2,500 cores were fully evaluated to converge to a Pareto Frontier of optimum solutions providing best compromise between the life-time target and the total core weight, as shown in Figure 1. The main benefit of this approach was to reduce the human effort and to be able to automatically re-run the optimization problem when changing the design problem. The multi-objective optimization identified various core solutions that would be optimum solutions for different types of applications.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Evaporative thermal resistance and its influence on microlayer evaporation

The ability to predict various aspects of boiling is important for both safety and design of water-cooled reactors. Component-scale modelling is necessarily done by semi-mechanistic, semi-empirical approaches, generally based on heat flux partitioning. This needs to be informed by multiple detailed experimental observations of boiling behavior. Such measurements are difficult to make, and much effort is being applied to microscopic computational modelling of the detailed boiling process. Aims of such activities include the mechanistic prediction of growth and detachment of one bubble during nucleate boiling, and the quantification of the associated heat transfer partitioning (evaporation, micro-convection, quenching). We here study a subset of the full problem, and focus on the thermal response of the boiling substrate to the early growth of a single vapour bubble during pool boiling of water at atmospheric pressure. In such conditions, a thin liquid film ('microlayer') is left behind beneath the bubble as this expands. The microlayer evaporates due to the temperature difference between the solid-liquid and vapour-liquid interface. Its thickness being small, of order of microns, the local evaporation rate per unit area of bubble base can be high, up to one kilogram per second. Microlayer evaporation can therefore be important in early stages of bubble growth. In this contribution, thermal response of the boiling substrate to microlayer evaporation is studied with a two-dimensional, axisymmetric transient conduction model, coupled with an algebraic sub-model of the liquid film. The flow of heat through the microlayer is modelled as conduction in the liquid and with a pseudo-convective 'evaporative' heat transfer coefficient at the liquid-vapor interface, accounting for the interface superheat driving the evaporation process. Thermal coupling (conjugate heat transfer) between microlayer and solid substrate is obtained with a time dependent non-homogeneous Neumann boundary condition, derived from the algebraic microlayer sub-model and applied at the top surface of the solid computational domain. The thermal resistance associated to the evaporative heat transfer mechanism is shown to depend on a highly uncertain parameter, termed an 'evaporation coefficient'. After some exploratory calculations of the likely importance of the evaporative resistance in the present context, the model is employed to interpret some recent microlayer measurements. Satisfactory agreement between computed and measured evolution of the microlayer profile is obtained if small values (between 0.01 and 0.10) of the evaporation coefficient are used. The order of magnitude of the predicted evaporation rate from the microlayer is consistent with experimental observations. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Recent Progress on the Stochastic Objective Decision Aide (SODA) Application

Idaho State University, in collaboration with Idaho National Laboratory, is engaged in development of a simple to use software application that utilizes stochastic techniques for the calculation of radiation doses associated with hypothetical radioactive material releases. This work is being performed through a grant from the U.S. Department of Energy (DOE) Nuclear Safety Research and Development (NSR and D) Program. Initial progress on the application was reported previously. Recent additions to the application are reported here. The Stochastic Objective Decision Aide (SODA) provides an easy to use software application to help decision makers support their judgment about the need or lack of need for safety structures, systems, and components. SODA is not intended to replace traditional design basis accident dose calculation methodology, nor is it intended to replace existing software used to perform formal dose consequence calculations. Rather, SODA is intended to supplement information obtained from existing codes to give a decision maker more information about an accident scenario. SODA also provides a simple method to perform parametric or sensitivity studies on individual input parameters. Non-reactor nuclear facilities operated under the approval authority of the US DOE use unmitigated hazard evaluations to determine if potential radiological doses associated with design basis events challenge dose evaluation guidelines. Unmitigated events that sufficiently challenge dose evaluation guidelines merit the selection of safety structures, systems, or components (SSCs) to prevent or mitigate the hazard. Dose consequence calculations traditionally involve use of the 'five-factor' formula: ST = MAR.DR.ARF.RF.LPF where ST is the source term (Bq), MAR is the total available material-at-risk (Bq), DR is the damage ratio (no units), ARF is the airborne release fraction (no units), RF is the respirable fraction (no units), and LPF is the leak path factor (no units). Potential radiation doses are then calculated using: CED = χ/Q.BR.ST.DCF (2) where CED is the committed effective dose (Sv), χ/Q is the plume dispersion (s/m{sup 3}), BR is the breathing rate (m{sup 3}/s), ST is the source term (Bq), and DCF is the dose conversion factor (Sv/Bq). Conservative single value input parameters are typically used to represent ARF, RF, LPF and BR. The traditional methodology, while conservative, can lead to skewed conclusions in the balance between cost and risk reduction resulting in over engineered systems with greater design, construction and operating costs. Rather than using a bounding single point value for each parameter in the dose consequence calculation, SODA uses distributions for some or all of the parameters. Each input parameter distribution is stochastically sampled and the resulting dose consequence calculation is repeated many times to develop a dose consequence distribution. The resulting distribution provides more information for the decision maker to rely upon when determining the need for safety SSCs. The SODA application was developed using MATLAB and it incorporates the use of Monte Carlo techniques as well as a graphical user interface (GUI). The application includes user selection of the governing distribution for parameters such as the MAR, DR, ARF, RF, LPF,χ/Q, BR, and DCF. While MATLAB was used for the development work, the application is distributed as a self-contained executable program. Features of the application include pull down menus with available distributions for the various parameters. The user has the option to plot the input parameter distribution that results from the random sampling process. The resulting dose consequence distribution is automatically analyzed to determine its similarity to well know distributions. This was done using the Bayesian Information Criterion method. If the resulting distribution is sufficiently similar to a well-known distribution, the application provides information about the distributions such as the mean value and other parameters. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Numerical analysis of dynamic load following response in a natural circulation molten salt power reactor system

The Molten Salt Reactor (MSR) concept is a rapidly evolving Generation IV design that has recently attracted favorable attention due to the potential for reducing waste generation, realizing passive safety features, and seizing on the opportunity for cost effective economics. An investigation into the power transient behavior of an autonomous load-following, closed-loop, natural circulation MSR system is important to quantifying operational and safety performance under dynamic conditions. This paper presents the results of a STAR-CCM+ and a comparatively simple asymmetric, one-dimensional, numerical model to solve the compound dynamic MSR power behavior subject to flow and temperature reactivity feedback only. Results show that reactor power is affected by fuel salt flow velocity (global) and temperatures (local bulk volume averages) in a coupled, time-delayed manner that results in a unique compound dynamic, closed-loop power feedback mechanism. The 1-D simulation approach opens the possibility of performing inexpensive computations to evaluate time-dependent reactor performance relative to thermo-physical fuel salt limitations. Results also potentially motivate a convincing conclusion that natural circulation MSRs provide a leap in safety and reliability.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Industry Application Emergency Core Cooling System Cladding Acceptance Criteria Early Demonstration

The U. S. NRC is currently proposing rulemaking designated as “10 CFR 50.46c” to revise the loss-of-coolant-accident (LOCA)/emergency core cooling system (ECCS) acceptance criteria to include the effects of higher burnup on cladding performance as well as to address other technical issues. The NRC is also currently resolving the public comments with the final rule expected to be issued in April 2016. The impact of the final 50.46c rule on the industry may involve updating of fuel vendor LOCA evaluation models, NRC review and approval, and licensee submittal of new LOCA evaluations or re-analyses and associated technical specification revisions for NRC review and approval. The rule implementation process, both industry and NRC activities, is expected to take 4-6 years following the rule effective date. As motivated by the new rule, the need to use advanced cladding designs may be a result. A loss of operational margin may result due to the more restrictive cladding embrittlement criteria. Initial and future compliance with the rule may significantly increase vendor workload and licensee cost as a spectrum of fuel rod initial burnup states may need to be analyzed to demonstrate compliance. Consequently, there will be an increased focus on licensee decision making related to LOCA analysis to minimize cost and impact, and to manage margin. The proposed rule would apply to a light water reactor and to all cladding types.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Development of an active detector for the characterization of the late-time radiation environment from a reactor pulse

Document available in abstract form only, full text of document follows: This paper discusses the use of a commercially available {sup 235}U fission chamber, with a matching compensating ion chamber, originally sold as a single-ended detector with the signal conducted over the shield of a coaxial cable. The authors designed an aluminum housing that isolates the two detectors and converts the signals to full differential mode as a noise-reduction technique. The signals are processed using the switched resistor technique to extend the signal range to longer times from the peak of the pulse [Luker, S. M., Griffin, P. J., King, D. B., and Suo-Anttila, A. J., 'Improved Diagnostics for Analysis of a Reactor Pulse Radiation Environment,' 13. International Symposium on Reactor Dosimetry, Akersloot, Netherlands, May 25, 2008, pp. 4-6.]. The newly configured fission chamber assembly has been used at the annular core research reactor at Sandia National Laboratories to provide a high-fidelity characterization of the neutron time profile from a pulsed operation. (authors)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Thermal-Hydraulic Simulations of Single Pin and Assembly Sector for IVG- 1M Reactor

Thermal-hydraulic simulations have been performed using computational fluid dynamics (CFD) for the highly-enriched uranium (HEU) design of the IVG.1M reactor at the Institute of Atomic Energy (IAE) at the National Nuclear Center (NNC) in the Republic of Kazakhstan. Steady-state simulations were performed for both types of fuel assembly (FA), i.e. the FA in rows 1 & 2 and the FA in row 3, as well as for single pins in those FA (600 mm and 800 mm pins). Both single pin calculations and bundle sectors have been simulated for the most conservative operating conditions corresponding to the 10 MW output power, which corresponds to a pin unit cell Reynolds number of only about 7500. Simulations were performed using the commercial code STAR-CCM+ for the actual twisted pin geometry as well as a straight-pin approximation. Various Reynolds-Averaged Navier-Stokes (RANS) turbulence models gave different results, and so some validation runs with a higher-fidelity Large Eddy Simulation (LES) code were performed given the lack of experimental data. These singled out the Realizable Two-Layer k-ε as the most accurate turbulence model for estimating surface temperature. Single-pin results for the twisted case, based on the average flow rate per pin and peak pin power, were conservative for peak clad surface temperature compared to the bundle results. Also the straight-pin calculations were conservative as compared to the twisted pin simulations, as expected, but the single-pin straight case was not always conservative with regard to the straight-pin bundle. This was due to the straight-pin temperature distribution being strongly influenced by the pin orientation, particularly near the outer boundary. The straight-pin case also predicted the peak temperature to be in a different location than the twisted-pin case. This is a limitation of the straight-pin approach. The peak temperature pin was in a different location from the peak power pin in every case simulated, and occurred at an inner pin just before the enrichment change. The 600 mm case demonstrated a peak clad surface temperature of 370.4 K, while the 800 mm case had a temperature of 391.6 K. These temperatures are well below the necessary temperatures for boiling to occur at the rated pressure. Fuel temperatures are also well below the melting point. Future bundle work will include simulations of the proposed low-enriched uranium (LEU) design. Two transient scenarios were also investigated for the single-pin geometries. Both were “model” problems that were focused on pure thermal-hydraulic behavior, and as such were simple power changes that did not incorporate neutron kinetics modeling. The first scenario was a high-power, ramp increase, while the second scenario was a low-power, step increase. A cylindrical RELAP model was also constructed to investigate its accuracy as compared to the higher-fidelity CFD. Comparisons between the two codes showed good agreement for peak temperatures in the fuel and at the cladding surface for both cases. In the step transient, temperatures at four axial levels were also computed. These showed greater but reasonable discrepancy, with RELAP outputting higher temperatures. These results provide some evidence that RELAP can be used with confidence in modeling transients for IVG.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Evaluation of LLNL's Nuclear Accident Dosimeters at the CALIBAN Reactor September 2010

The Lawrence Livermore National Laboratory uses neutron activation elements in a Panasonic TLD holder as a personnel nuclear accident dosimeter (PNAD). The LLNL PNAD has periodically been tested using a Cf-252 neutron source, however until 2009, it was more than 25 years since the PNAD has been tested against a source of neutrons that arise from a reactor generated neutron spectrum that simulates a criticality. In October 2009, LLNL participated in an intercomparison of nuclear accident dosimeters at the CEA Valduc Silene reactor (Hickman, et.al. 2010). In September 2010, LLNL participated in a second intercomparison of nuclear accident dosimeters at CEA Valduc. The reactor generated neutron irradiations for the 2010 exercise were performed at the Caliban reactor. The Caliban results are described in this report.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Three-dimensional anisotropic pressure free boundary equilibria

Free boundary three-dimensional anisotropic pressure magnetohydrodynamic equilibria with nested magnetic flux surfaces are computed through the minimisation of the plasma energy functional W = integral(V) d(3)x[B-2/(2 mu(0)) + p(parallel to)/(Gamma - 1)]. The plasma-vacuum interface is varied to guarantee the continuity of the total pressure [p(perpendicular to) + B-2/(2 mu(0))] across it and the vacuum magnetic field must satisfy the Neumann bo undary condition that its component normal to this interfaced surface vanishes. The vacuum magnetic field corresponds to that driven by the plasma current and external coils plus the gradient of a potential function whose solution is obtained using a Green's function method. The energetic particle contributions to the pressure are evaluated analytically from the moments of the variant of a bi-Maxwellian distribution function that satisfies the constraint B . del F-h = 0. Applications to demonstrate the versatility and reliability of the numerical method employed have concentrated on high-beta off-axis energetic particle deposition with large parallel and perpendicular pressure anisotropies in a 2-field period quasiaxisymmetric stellarator reactor system. For large perpendicular pressure anisotropy, the hot particle component of the p(perpendicular to) distribution localises in the regions where the energetic particles are deposited. For large parallel pressure anisotropy. the pressures are more uniform around the flux surfaces. (C) 2009 Elsevier B.V. All rights reserved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

How to Produce a Reactor Neutron Spectrum Using a Proton Accelerator

A method for reproducing the neutron energy spectrum present in the core of an operating nuclear reactor using an engineered target in an accelerator proton beam is proposed. The protons interact with a target to create neutrons through various (p,n) type reactions. Spectral tailoring of the emitted neutrons can be used to modify the energy of the generated neutron spectrum to represent various reactor spectra. Through the use of moderators and reflectors, the neutron spectrum can be modified to reproduce many different spectra of interest including spectra in small thermal test reactors, large pressurized water reactors, and fast reactors. The particular application of this methodology is the design of an experimental approach for using an accelerator to measure the betas produced during fission to be used to reduce uncertainties in the interpretation of reactor antineutrino measurements. This approach involves using a proton accelerator to produce a neutron field representative of a power reactor, and using this neutron field to irradiate fission foils of the primary isotopes contributing to fission in the reactor, creating unstable, neutron rich fission products that subsequently beta decay and emit electron antineutrinos. A major advantage of an accelerator neutron source over a neutron beam from a thermal reactor is that the fast neutrons can be slowed down or tailored to approximate various power reactor spectra. An accelerator based neutron source that can be tailored to match various reactor neutron spectra provides an advantage for control in studying how changes in the neutron spectra affect parameters such as the resulting fission product beta spectrum.

43 PARTICLE ACCELERATORS↗