Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material degradation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Strengthening of tungsten by coherent rhenium precipitates formed during low fluence irradiation

Experimental data show that the accumulation of rhenium and osmium from transmutation reactions severely affect the microstructural evolution and property degradation of tungsten-based materials under neutron irradiation. Theory and modeling have confirmed that Re atom transport in W is by irradiation-produced migrating self-interstitial atoms. With this diffusion mode in operation, a specific microstructure evolution is realized when at relatively low neutron fluence the Re-rich precipitates are formed, while the void and interstitial loop population development is suppressed, affecting the mechanical properties. Here, this research shows the effect of small coherent Re-rich precipitates on the dislocation glide under stress, investigated using the molecular dynamics approach with empirical interatomic potentials. The results are compared with an earlier simulation of void hardening in W. It is demonstrated that small coherent Re-rich precipitates of less than 6 nm diameter represent relatively weak obstacles for moving edge dislocations. The implication of these results on the interpretation of experimental results is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Measurement of grain boundary strength of Inconel X-750 superalloy using in-situ micro-tensile testing techniques in FIB/SEM system

Grain boundaries (GBs), known as two-dimensional defects, are omnipresent in polycrystalline metallic alloys and thus influence a wide range of mechanical properties under different environmental conditions like irradiation and corrosion. Therefore, quantifying the strength of individual GBs is critical for understanding the degradation of mechanical properties of materials under different conditions. In this study we developed an efficient approach for the fabrication of micro-tensile specimens with a GB almost perpendicular to the tensile direction, which is expected to advance the development of individual GB tensile testing at micro or nanoscale in a wide scope of materials. Further, an in-situ cantilever micro-tensile testing method was developed and used to quantify the strength of a Σ3 GB in Inconel X-750 with the combination of finite element modeling. The average ultimate tensile strength (UTS) of a non-irradiated Σ3 GB is estimated at around 1.4 GPa, comparable to that of a neutron-irradiated Σ3 GB with a dose of ~1.5 dpa (1.3 GPa). Moreover, the in-situ push-to-pull micro-tensile testing technique developed in this work provides valuable insights into the high-angle GB deformation and fracture behavior. This method generates qualitatively similar ductility behavior before and after neutron irradiation as the bulk material testing. However, the ductility and UTS values obtained from this method are different from bulk measurements due to vastly different specimen dimensions.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Linking microstructure to creep behavior in vertically and horizontally built LPBF Haynes 282 compared with wrought material via θ -projection

Laser Powder Bed Fusion (LPBF) has emerged as a promising route for fabricating intricate geometries in high-performance alloys. Haynes 282 (H282) is a strong candidate for applications such as heat exchangers or engines due to its excellent creep strength and thermal stability; however, the long-term creep behavior of LPBF-processed H282 remains poorly understood. In this study, the θ -projection method is used to analyze and extrapolate the creep behavior of vertically built LPBF, horizontally built LPBF, compared to wrought H282 tested at 816 °C. Vertically built LPBF H282 exhibits the lowest minimum creep rate (MCR), while the horizontally built condition shows a higher MCR comparable to that of wrought H282. Despite these differences, both LPBF conditions exhibit significantly shorter rupture life and reduced rupture strain than the wrought material, with the most severe degradation observed in the horizontal builds, consistent with an earlier onset of tertiary creep and accelerated strain-rate evolution. Microstructural characterization reveals that both LPBF and wrought H282 exhibit abundant twin-related boundary character; however, their grain boundary topologies differ markedly. The wrought alloy contains a higher fraction of low-angle grain boundaries and continuous twin lamellae, whereas the LPBF microstructure is characterized by a suppressed low-angle boundary population and fragmented twin-related boundaries embedded within irregular high-angle grain boundary networks. Fractographic analysis further reveals predominantly intergranular cracking in LPBF H282, accompanied by grain-boundary-decorated carbides, Al 2 O 3 inclusions, and high-aspect-ratio pores. These results demonstrate that grain boundary topology, rather than minimum creep rate alone, plays a critical role in governing creep damage accumulation and rupture behavior in LPBF and wrought H282.

Creep↗
DOE OSTI2026

Multiscale Modeling and Experimental Insights into High-Temperature Soil Biodegradation Dynamics of Semi-Crystalline Poly(Lactic Acid) Nonwoven Fabrics

This study investigates the biodegradation of semi-crystalline poly(lactic acid) (PLA) nonwovens (NWs) in soil at 58 °C using both experimental and mathematical modeling approaches. The model utilizes a system of parabolic diffusion-reaction partial differential equations (PDEs) to elucidate chemical transformations over time and in space. It accounts for phenomena such as the diffusion of water and lactic acid monomers through the polymer matrix and into the surrounding soil, along with their microbial breakdown. It also accounts for the initial PLA crystallinity and predicts its evolution in time. The model is solved numerically for a single filament, and the results were used to shed light on PLA NW transformations observed in soil over a 180-day incubation period. Various characterization techniques, including scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and Raman spectroscopy, were employed to assess morphological changes, crystallinity, and molecular changes in the NWs throughout the experiment. By comparing the experimental data with the model predictions, the hydrolysis rate coefficient was found to be 3.37 × 10 -7 s -1 , while the rate of microbial degradation of lactic acid monomers was faster, of the order of 9.63 × 10 -7 s -1 . The findings highlight the significant role of crystallinity in the biodegradation process. The PLA degradation ceases when no amorphous material remains, and the crystallinity reaches 0.8, as observed in the experiments by day 120. Furthermore, this research contributes to a deeper understanding of PLA biodegradation dynamics and offers insights for effectively managing biodegradable materials in environmental settings.

Diffusion−reaction modeling↗
DOE OSTI2022

Investigation of Inverse Temperature Effects During Thermal-Radiation Aging of Semicrystalline Cable Insulation

Inverse temperature effects were observed for semi-crystalline polymers subjected to combined thermal and irradiation aging. The mechanical durability of materials aged at low temperatures degrades with dose faster than at high temperatures. In this paper, two crosslinked polyethylene (XLPE) and two ethylene propylene rubber (EPR) type nuclear cable insulations were exposed to thermal-radiation aging at 100Gy/h up to 30Mrad and three temperatures (26°C, 50°C, 90°C). Their mass change and color change after aging were analyzed.

Ni, Yelin↗
DOE OSTI2022

Effect of Electrolytes on the Cathode-Electrolyte Interfacial Stability of Fe-Based Layered Cathodes for Sodium-Ion Batteries

Iron (Fe)-based layered oxide cathodes that employ Fe 3+ /Fe 4+ redox reaction present a family of attractive cathode materials for sodium-ion batteries as iron is abundant, low-cost, and environmentally benign. However, their electrochemical performance is not yet satisfactory and requires further improvement. In this study, we investigate the effect of electrolytes on the electrochemical performance of α -NaFeO 2 , a prototypical model of Fe-based layered cathodes. First, we established the critical impact of the poor cathode-electrolyte interfacial stability on cell performances. Systematic electrochemical tests and material characterizations further revealed the degradation mechanism in which the highly reactive Fe 4+ state in the charged Na 1−x FeO 2 electrodes promotes severe electrolyte decomposition and subsequent growth of a thick interface layer that leads to impedance rise and performance degradation. In addition, the superior performance of NaPF 6 over NaClO 4 and the beneficial effect of the FEC additive are reported.

25 ENERGY STORAGE↗
DOE OSTI2021

Identifying Limitations of ASME Section III Division 5 For Advanced SMR Designs

This report provides an overview of the ASME Boiler & Pressure Vessel Section III, Division 5 rules for the design and construction of high temperature nuclear reactor components. The overview focuses on the application of the rules to the design of Small Modular Reactors (SMRs). The discussion covers the general ASME Code rules for base metal design and construction, the rules for designing weldments, and provides an overview of environmental degradation mechanisms affecting reactor structural materials. The analysis includes historical context on the development of the ASME design approach and a description of what actions could be taken to mitigate the gaps identified in the report. The report concludes with a summary of the key gaps identified in the rules, as they apply to SMR, and a list of recommendations on how those gaps might be addressed.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Multi-Process Tooling

Decisions made early in the automotive design process influence material selection, which in turn dictates process selection and tool design. Because of tool build time and cost of tooling, the original path is not easily altered, even if there is compelling evidence that another material or process would be beneficial. This project focused on tool design that is agile enough to allow its use in multiple processes—injection, injection compression, and extrusion-compression. This tool design allows for the manufacture of components with the most efficient process or materials, without building multiple, single-process tools. The primary purpose of the Multi-Process Tool project was to physically demonstrate that a single, well-designed tool could be used to manufacture parts with a variety of materials that require different processes. A multi-process tool would be beneficial to providing data for any changes to the process since materials and processes can be interchanged without incurring additional tool cost(s). Battery tray parts, (representative of a multi-process tool, were successfully manufactured using various types of materials, such as fiber reinforced (carbon fiber and/or glass fibers, recycled carbon fibers), amorphous (PP, TPU), semi-crystalline (PA6, PA66), and crystalline (thermoset epoxy resin) polymers. Processing of the parts was achieved by injection molding, compression molding, compression overmolding, and injection overmolding. Specimens extracted from various locations on the battery tray parts were evaluated for mechanical properties (flexure and interlaminar shear strength properties). The results show that the tool can be used to produce parts from a wide range of materials and processes with no degradation of the physical or cosmetic properties.

42 ENGINEERING↗
DOE OSTI2022

Durable, High-Performance Unitized Reversible Fuel Cells Based on Proton Conductors

The main objective of this project was to develop robust, highly efficient, and economically viable H + -conducting membrane-based, unitized reversible fuel cell (H-URFC) technology for large-scale co-located energy storage and power generation. Another objective of this project is to gain a profound understanding of the degradation mechanisms of key stack materials and interfaces using various in situ, ex situ, and operando measurements guided by theoretical analysis. Nanostructured components will be integrated into cell design and the interfaces between electrodes and electrolyte will be modified with active bi-functional catalysts and protective coatings in order to achieve >70% roundtrip efficiency at 1 A/cm2 in both the fuel cell and the electrolysis modes. The end goal of the project is to advance the technology to the point that a university-industry collaboration can be established to scale up the technology for early adoption, and eventually enabling a pathway to large-scale energy storage that utilizes chemical storage and conversion for electrical grid balancing.

08 HYDROGEN↗
DOE OSTI2021

Simulating Oxidation of Carbon Surfaces by Atomic Oxygen Coupled with a Finite Rate Oxidation Model

Oxidation is a prominent factor in degradation of carbon based ablative materials at high temperatures, resulting in mass loss and material recession through chemical and mechanical erosion. In this paper, a finite rate carbon oxidation model coupled with surface recession is implemented in the Porous Ablation and Thermal Response (Panther) software to investigate carbon oxidation by atomic oxygen over a range of temperatures and pressures. Panther is utilized to investigate the finite rate oxidation model proposed by Swaminathan-Gopalan et al. at conditions of higher pressure and flux relative to the experiments it was built on.

Kirmanoglu, Kaan K.↗
DOE OSTI2023

Analysis of Crystalline Defects Caused by Growth on Partially Planarized Spalled (100) GaAs Substrates

We analyze the effect of growth on non-(100) surfaces resulting from incomplete planarization of spalled GaAs wafers on the defect structure of GaAs solar cell layers grown by hydride vapor phase epitaxy (HVPE). Controlled spalling of (100)-oriented GaAs has the potential to reduce substrate costs for III-V epitaxy; however, it creates regularly faceted surfaces that may complicate the growth of high-quality III-V optoelectronic devices. We leverage the anisotropic growth rate of HVPE to planarize these faceted GaAs substrates, reducing the surface roughness and degree of faceting. We observe degraded solar cell performance and material quality in sample areas where facets are not completely removed. We used dark lock-in thermography and photoluminescence to identify recombination in areas that were not fully planarized. We used cathodoluminescence to identify the presence of extended defects in these regions, which are correlated with bandgap fluctuations in the material. We hypothesize that these defects were created by strain from compositional fluctuations in ternary alloys grown on the faceted surfaces. This work elucidates the potential issues of solar cells grown on faceted surfaces and builds understanding toward realizing high performance III-V photovoltaics with the cost-reduction potential of controlled spalling.

14 SOLAR ENERGY↗
DOE OSTI2022

Optimization of particle tracking methods for stochastic media

Random media emerge in several applications involving particle transport, encompassing e.g. photon propagation through Rayleigh-Taylor instabilities in fuel pellets for inertial confinement fusion, or neutron multiplication problems related to the assessment of re-criticality risk following severe accidents with fuel degradation. Reference calculations in such material configurations by means of Monte Carlo transport codes are particularly challenging, since high-density stochastic media might involve several hundreds of thousands of volumes and thus make particle tracking routines extremely cumbersome. In order to cope with these issues, two distinct strategies have been proposed so far: the use of neighbor maps, or the use of delta tracking. In this work we will compare these methods and illustrate their specific merits and drawbacks, as taken both alone and in combination with each other. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Low‐PGM and PGM‐Free Catalysts for Proton Exchange Membrane Fuel Cells: Stability Challenges and Material Solutions

Abstract Fuel cells as an attractive clean energy technology have recently regained popularity in academia, government, and industry. In a mainstream proton exchange membrane (PEM) fuel cell, platinum‐group‐metal (PGM)‐based catalysts account for ≈50% of the projected total cost for large‐scale production. To lower the cost, two materials‐based strategies have been pursued: 1) to decrease PGM catalyst usage (so‐called low‐PGM catalysts), and 2) to develop alternative PGM‐free catalysts. Grand stability challenges exist when PGM catalyst loading is decreased in a membrane electrode assembly (MEA)—the power generation unit of a PEM fuel cell—or when PGM‐free catalysts are integrated into an MEA. More importantly, there is a significant knowledge gap between materials innovation and device integration. For example, high‐performance electrocatalysts usually demonstrate undesired quick degradation in MEAs. This issue significantly limits the development of PEM fuel cells. Herein, recent progress in understanding the degradation of low‐PGM and PGM‐free catalysts in fuel cell MEAs and materials‐based solutions to address these issues are reviewed. The key factors that degrade the MEA performance are highlighted. Innovative, emerging material concepts and development of low‐PGM and PGM‐free catalysts are discussed.

Du, Lei↗
DOE OSTI2021

Insights on autophagosome–lysosome tethering from structural and biochemical characterization of human autophagy factor EPG5

Pivotal to the maintenance of cellular homeostasis, macroautophagy (hereafter autophagy) is an evolutionarily conserved degradation system that involves sequestration of cytoplasmic material into the double-membrane autophagosome and targeting of this transport vesicle to the lysosome/late endosome for degradation. EPG5 is a large-sized metazoan protein proposed to serve as a tethering factor to enforce autophagosome–lysosome/late endosome fusion specificity, and its deficiency causes a severe multisystem disorder known as Vici syndrome. Here, we show that human EPG5 (hEPG5) adopts an extended “shepherd’s staff” architecture. We find that hEPG5 binds preferentially to members of the GABARAP subfamily of human ATG8 proteins critical to autophagosome–lysosome fusion. The hEPG5–GABARAPs interaction, which is mediated by tandem LIR motifs that exhibit differential affinities, is required for hEPG5 recruitment to mitochondria during PINK1/Parkin-dependent mitophagy. Lastly, we find that the Vici syndrome mutation Gln336Arg does not affect the hEPG5’s overall stability nor its ability to engage in interaction with the GABARAPs. Collectively, results from our studies reveal new insights into how hEPG5 recognizes mature autophagosome and establish a platform for examining the molecular effects of Vici syndrome disease mutations on hEPG5.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Revisiting the activity of two poly(vinyl chloride)- and polyethylene-degrading enzymes

Biocatalytic degradation of non-hydrolyzable plastics is a rapidly growing field of research, driven by the global accumulation of waste. Enzymes capable of cleaving the carbon-carbon bonds in synthetic polymers are highly sought-after as they may provide tools for environmentally friendly plastic recycling. Despite some reports of oxidative enzymes acting on non-hydrolyzable plastics, including polyethylene or poly(vinyl chloride), the notion that these materials are susceptible to efficient enzymatic degradation remains controversial, partly driven by a general lack of studies independently reproducing previous observations. Here, we attempt to replicate two recent studies reporting that deconstruction of polyethylene and poly(vinyl chloride) can be achieved using an insect hexamerin from Galleria mellonella (so-called “Ceres”) or a bacterial catalase-peroxidase from Klebsiella sp., respectively. Reproducing previously described experiments, we do not observe any activity on plastics using multiple reaction conditions and multiple substrate types. Digging deeper into the discrepancies between the previous data and our observations, we show how and why the original experimental results may have been misinterpreted.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Recruiting Perovskites to Degrade Toxic Trinitrotoluene

Everybody knows TNT, the most widely used explosive material and a universal measure of the destructiveness of explosions. A long history of use and extensive manufacture of toxic TNT leads to the accumulation of these materials in soil and groundwater, which is a significant concern for environmental safety and sustainability. Reliable and cost-efficient technologies for removing or detoxifying TNT from the environment are lacking. Despite the extreme urgency, this remains an outstanding challenge that often goes unnoticed. We report here that highly controlled energy release from explosive molecules can be accomplished rather easily by preparing TNT–perovskite mixtures with a tailored perovskite surface morphology at ambient conditions. These results offer new insight into understanding the sensitivity of high explosives to detonation initiation and enable many novel applications, such as new concepts in harvesting and converting chemical energy, the design of new, improved energetics with tunable characteristics, the development of powerful fuels and miniaturized detonators, and new ways for eliminating toxins from land and water.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Defect Kinetics and Control for Module Reliability

Potential induced degradation is currently one of the most important module degradation mechanisms. It has been suggested that stacking faults decorated with sodium from the module glass are responsible for this effect and authors have also shown the reversibility of this effect upon reverse biasing of the module. The importance of sodium in the failure mechanism is clear, however, little is known regarding the factors that control its diffusion into the wafer, making it nearly impossible to predict the performance of a given module and engineer it to be better. Sodium migration from module glass into silicon cells and the resulting module degradation is a clear example of how defect kinetics can determine overall module performance and long-term reliability. To the detriment of the industry and its bankability, no quantitative models yet exist to predict defect-assisted module degradation, limiting the progress in improving reliability. In particular, the understanding of defect behavior under high electric fields, under stresses imparted by encapsulation or temperature, and under real operating conditions over long periods of time is a crucial gap in the current state-of-the-art. In this work we developed a Defect-Device-Degradation model to predict defect behavior and its impact on device performance over the module operational lifetime using experimentally-determined defect parameterizations. The validated model will provide a platform for manufacturing process optimization across input materials and architectures to avoid deleterious defects upstream and enable enhanced module robustness.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High-Temperature-Performance Cyanate Ester Composites with Carboranes

Cyanate ester (CE) is an important class of materials among high-temperature performance thermosets. It is used in aerospace launch vehicles, heat sinks, booms, and trusses of satellites etc. due to its high glass transition temperatures (>220°C), excellent thermal stability, and low flammability. Current approaches to improve the thermal stability of CE include incorporation of siloxanes or phosphorus- based flame retardants (PFRs). In this work, we have explored boron-based hydroxy (PD) and epoxy (EP) functionalized carborane additives to improve the thermal properties of CE. Carborane fillers were solvent blended at various mass loadings in the resin and cured to study their effect on thermal properties. PD and EP carboranes react with CE to form iminocarbonate and oxazolidinone linkages respectively. Cure kinetics studies at different wt% loadings explained that carboranes catalyze the curing reaction by reducing curing activation energy by about 54% and 26% for 10 wt% loadings of PD and EP carboranes respectively. In addition, carborane-filled cyanate ester (CE) nanocomposites demonstrate an exceptionally high thermal stability as compared to the pristine resin in air and inert environment. Our thermogravimetric analysis (TGA) experiments show that the ultimate char yield of the resin can be increased from 0% to as high as 76% and 82% with 30 wt% PD and EP carborane loading respectively at 1000 °C in air. The initial degradation temperature T d;5 of the composites decreased with increasing carborane loadings in both air and argon. For instance, T d;5 for CE was 465 and 471.6 °C in argon and air while that for P20 was 437.4 and 452.1 °C. Modulated TGA studies gave evidence of the effect of carboranes on degradation kinetics and the mechanism of the resin in air and inert environment. The effect of bonding between carboranes and CE at various loadings on the thermal expansion of the matrix was also studied using Thermomechanical Analyzer (TMA). PD carborane reduced the T g for P20 to about 225 °C while CE had T g >350 °C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗