Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Effect of substrate temperature on the magnetic properties of epitaxial sputter-grown Co/Pt

Epitaxial Co/Pt films have been deposited by dc-magnetron sputtering onto heated C-plane sapphire substrates. X-ray diffraction, the residual resistivity, and transmission electron microscopy indicate that the Co/Pt films are highly ordered on the atomic scale. The coercive field and the perpendicular magnetic anisotropy increase as the substrate temperature is increased from 100–250 °C during deposition of the Co/Pt. Measurement of the domain wall creep velocity as a function of applied magnetic field yields the domain wall pinning energy, which scales with the coercive field. Evidence for an enhanced creep velocity in highly ordered epitaxial Co/Pt is found.

36 MATERIALS SCIENCE↗

Rapid Nb 3 Sn film growth by sputtering Nb on hot bronze

Nb deposited by magnetron sputtering onto hot Cu-15 wt.%Sn bronze substrates at temperatures above 700 °C achieved Nb 3 Sn film growth at a rate of 33 nm min -1 , which was an order of magnitude faster than that achieved for deposition of Nb on bronze at low temperature followed by in situ post reaction at the same high temperatures. Tin content in the Nb 3 Sn films made on hot bronze was ~26.3%, which is significantly higher than ~24.5% obtained by post-reaction as well as for typical bulk reactions between Nb and α -bronze. The Nb 3 Sn lattice parameter was consistent with measured tin content and predicted elastic strain for both routes. Critical temperatures of 14 K–16 K, instead of 18 K, were consistent with elastic strain due to coefficient of thermal expansion mismatch between the Nb 3 Sn and bronze substrate and, for the hot-bronze samples, stress related to the growth mechanism. Films were fully coalesced and had surface roughness values <20 nm over a 100 μ m 2 scan. Grain structure of the Nb 3 Sn films produced by Nb sputtering on hot bronze resembles zone 2 in the Thornton structure-zone diagram, in contrast to the equiaxed grain structure reminiscent of microstructure observed in reacted Nb 3 Sn wires exhibited by the post-reaction route.

Physics↗

Thermochromic VO{sub 2} nanorods made by sputter deposition: Growth conditions and optical modeling

Reactive dc magnetron sputtering onto glass-based substrates yielded deposits of thermochromic VO{sub 2} with well-developed nanorods and nanowires. Their formation was promoted by high substrate temperature (above {approx}500 Degree-Sign C), sufficient film thickness, proper inlet of the reactive gas, dispersed gold 'seeds,' and pronounced substrate roughness. Rutherford back scattering ascertained mass thicknesses, scanning electron microscopy depicted the nanostructures, and glancing incidence X-ray diffraction proved that single-phase VO{sub 2} was normally formed. Spectrophotometric measurements of total and diffuse transmittance and reflectance on VO{sub 2} thin films, at room temperature and {approx}100 Degree-Sign C, allowed us to determine complex dielectric functions below and above the 'critical' temperature for thermochromic switching ({approx}68 Degree-Sign C). These data were then used in computations based on the Bruggeman effective medium theory applied to randomly oriented prolate spheroidal structural units to derive the optical properties of the deposits. Experimental and computed data on spectral absorptance were found to be in good qualitative agreement.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Correlation of chemical composition and electrical properties of rf sputtered alumina films

Alumina films were prepared by radio frequency magnetron sputtering from an aluminum oxide target on an indium tin oxide covered glass. The purpose of the study was to test the influence of the sputter parameters on the elemental composition, surface morphology, and electrical insulation properties (breakdown fields and leakage currents). Tested parameters were the sputter gas (Ar) pressure, the sputter rate, the sputter power, the sputter gas composition (Ar:O{sub 2}), the conditioning of the target, the residual base pressure, and the substrate temperature. The surface morphology of the films was investigated by atomic force microscopy. Depth profiles of the elemental compositions were measured by elastic recoil detection using energetic heavy ions, and the insulation properties were investigated by current voltage measurements and impedance spectroscopy. The main finding is that the leakage currents increase by about five orders of magnitude, if the atomic ratio of O:Al increases from 1.35 to 2.0. In parallel the breakdown fields decrease by a factor of 100, and the character of the breakdowns changes from soft to hard. The highest breakdown fields (2.4 MV/cm) and smallest leakage currents (6.5x10{sup -8} A/cm{sup 2} at 2.0 MV/cm) are obtained for slightly Al rich films with small atomic concentrations of H (<0.5 at. %). These films were sputtered in pure Ar and under the lowest possible pressure of the residual gas.

36 MATERIALS SCIENCE↗

Preparation of ultrathin sputtered gold films on palladium as efficient oxygen reduction electro-catalysts

Herein, we present the preparation of ultrathin gold (Au) films on different M (M = Pd, Pt, Rh, Ir, and Ru) electrodes (Au/M) using magnetron sputtering deposition for oxygen reduction reaction (ORR). The ORR electro-catalytic activities of prepared Au/M catalysts increase as follows: Au/Ru < Au/Ir < Au/Rh < Au/Pt < Au/Pd. Accordingly, the oxygen reduction catalytic behaviors of the Au-modified palladium (Au/Pd) thin films with various Au thicknesses (0.16, 0.24, 0.5, and 1 nm) are investigated in acidic environments. It is found that Au modifications can promote oxygen reduction performances due to the development of more catalytic active sites on the Pd catalyst through the existence of Au atoms. Noticeably, Au/Pd samples exhibit a connection in oxygen reduction ability as a function of Au thickness, with the ultrathin 0.16 nm Au/Pd being the most active ORR catalyst. Significantly, the 0.16 nm Au/Pd material demonstrates superior stability after 1000 potential cycles compared with the 0.16 nm Pt/Pd owing to the influence of Au coating and structurally stable surfaces. Therefore, surface modification with the deposition of Au films on Pd represents a favorable technique to boost both the ORR capability and stability of the electro-catalysts.

Magnetron sputtering↗

Probing Non-Equilibrium Pair-Breaking and Quasiparticle Dynamics in Nb Superconducting Resonators Under Magnetic Fields

We conducted a comprehensive study of the non-equilibrium dynamics of Cooper pair breaking, quasiparticle (QP) generation, and relaxation in niobium (Nb) cut from superconducting radio-frequency (SRF) cavities, as well as various Nb resonator films from transmon qubits. Using ultrafast pump–probe spectroscopy, we were able to isolate the superconducting coherence and pair-breaking responses. Our results reveal both similarities and notable differences in the temperature- and magnetic-field-dependent dynamics of the SRF cavity and thin-film resonator samples. Moreover, femtosecond-resolved QP generation and relaxation under an applied magnetic field reveals a clear correlation between non-equilibrium QPs and the quality factor of resonators fabricated by using different deposition methods, such as DC sputtering and high-power impulse magnetron sputtering. These findings highlight the pivotal influence of fabrication techniques on the coherence and performance of Nb-based quantum devices, which are vital for applications in superconducting qubits and high-energy superconducting radio-frequency applications.

43 PARTICLE ACCELERATORS↗

Ion Generator

Andre Anders discuss magnetron sputtering which is a technology used for fin films.

36 MATERIALS SCIENCE↗

Effects of temperature and near-substrate plasma density on the structural and electrical properties of dc sputtered germanium thin films

Germanium thin films were deposited by dc reactive magnetron sputtering as a function of substrate temperature and ion flux using an unbalanced magnetron with an external magnetic field. The ion flux and energy distribution were measured using a retarding field energy analyzer (RFEA), a flat probe with a guard ring, and cylindrical Langmuir probes. The RFEA ion flux, the flat probe saturation currents, and the ion densities inferred from the cylindrical probe data are in very good agreement over a wide range of plasma densities, which were varied both by the external coil current and discharge power. The RFEA ion energy distributions are in good agreement with the plasma potentials inferred from the cylindrical probes, and suggest that the nonuniformity of the plasma in the vicinity of the substrate holder should be considered in the interpretation of probe results in these systems. The deposited films were characterized by x-ray diffraction, Raman spectroscopy, optical transmission, resistivity, and Hall effect measurements. Under low ion bombardment conditions, an abrupt onset of the crystalline phase with respect to temperature is observed in the Raman and x-ray diffraction measurements, and the crystal quality increases with increasing temperature above the transition temperature. The transition is also accompanied by a sharp decrease in film resistivity. The microcrystalline films have a strong preferential orientation in the (220) direction, and are p type with carrier densities in the range 10{sup 18} cm{sup -3} and mobilities in the range 15-30 cm{sup 2}/V-s. The structural and electronic properties of the films are sensitive to the ion flux. Near the transition temperature the effects of increasing ion flux can be attributed to the small temperature rise that accompanies the higher plasma density. At higher temperatures the increased ion flux results in a more random crystallographic orientation, with significantly lower carrier concentrations and only slightly lower carrier mobilities, implying either a reduction in acceptor defect density and/or the creation of compensating n-type defects.

36 MATERIALS SCIENCE↗

Effect of substrate temperature on sputter-deposited boron carbide films

Sputter deposition of B4C films with tailored physical properties remains a challenge. Here, we systematically study how substrate temperature influences the properties of B4C films deposited by direct current magnetron sputtering onto planar substrates held at temperatures in the range of 100-510°C. Results show that all films are amorphous stoichiometric B4C, with low O content of ~1 at. %. Films deposited onto substrates at 100°C exhibit high compressive residual stress and decreased mechanical properties. Therefore, for elevated substrate temperatures in the range of 180-510°C, film mass density, surface roughness, Young’s modulus, and hardness are weakly dependent on substrate temperature. However, in this temperature range, an increase in substrate temperature leads to larger residual compressive stress accompanied by a corresponding reduction in the concentration of nanoscale inhomogeneities. At least for the landing atom ballistics conditions studied here, a substrate temperature range of ~185-250°C is optimum for growing films with near-zero intrinsic residual stress. The overall weak substrate temperature dependence of film properties revealed in this work is favorable for the development of a robust deposition process, particularly for the case of deposition onto non-planar substrates where temperature control is often challenging.

36 MATERIALS SCIENCE↗

Sputter deposition of high electrical resistivity Au-Ta alloy coatings on rotating substrates

Sputter deposition of gold-tantalum alloy coatings is a key process for manufacturing hohlraums for magnetically-assisted inertial confinement fusion implosions. In this report we describe direct current magnetron sputter deposition of ~ 10 - μ~ 10 - μm-thick films of Au-80 at.% Ta onto rotating sphero-cylindrical hohlraum and planar Si witness substrates. Emphasis is given to how film microstructure and properties are affected by main deposition parameters, including argon working gas pressure, substrate bias, and the source composition (a single alloyed target compared to co-sputtering from two elemental targets). Experimental findings are correlated with distributions of landing energies and incident angles of depositing species calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. Deposition conditions characterized by low energetics of depositing species favor the formation of a β-Ta-like phase. Implications of these results to hohlraum fabrication are discussed.

36 MATERIALS SCIENCE↗

Stable p-i-n FAPbBr 3 devices with improved efficiency using sputtered ZnO as electron transport layer [Stable p-i-n FAPbBr 3 devices with improved efficiency using sputtered inorganic electron transport layer]

Here, radio-frequency magnetron sputtering is demonstrated as an effective tool to deposit highly crystalline thin zinc oxide (ZnO) layer directly on perovskite absorber as an electron transport layer (ETL). As an absorber, formamidinium lead tribromide (FAPbBr 3 ) is fabricated through a modified single-step solution process using hydrogen bromide (HBr) as an additive resulting in complete surface coverage and highly crystalline material. A planar p-i-n device architecture with spin-coated poly-(3,4-ethylenedioxythiophene):poly-styrenesulfonic acid (PEDOT:PSS) as hole transport material (HTM) and sputtered ZnO as ETL results in a short circuit current density of 9.5 mA cm -2 and an open circuit potential of 1.19 V. Numerical simulations are performed to validate the underlying loss mechanisms. The use of phenyl C 60 butyric acid methyl ester (PCBM) interface layer between FAPbBr 3 and sputter-coated ZnO offers shielding from potential plasma-related interface damage. The modified interface results in a better device efficiency of 8.3% with an open circuit potential of 1.35 V. Such devices offer better stability under continuous illumination under ambient conditions in comparison with the conventional organic ETL (PCBM)-based devices.

14 SOLAR ENERGY↗

Effects of surface tension and viscosity on gold and silver sputtered onto liquid substrates

Here, we report on DC magnetron sputtering of gold and silver onto liquid substrates of varying viscosities and surface tensions. We were able to separate the effects of viscosity from surface tension by depositing the metals onto silicone oils with a range of viscosities. The effects of surface tension were studied by depositing the metals onto squalene, poly(ethylene glycol), and glycerol. It was discovered that dispersed nanoparticles were formed on liquids with low surface tension and low viscosity whereas dense films were formed on liquids with low surface tension and high viscosity. Nanoparticles were formed on both the liquid surface and within the bulk liquid for high surface tension liquids. Our findings can be used to tailor the metal and liquid interaction to fabricate particles and films for various applications in optics, electronics, and catalysis.

36 MATERIALS SCIENCE↗

XPS Investigation of Surface Secondary Phase Segregation in CIGS Thin Film

Cu(In, Ga)Se{sub 2} (CIGS) thin films were deposited on Molybdenum (Mo) coated soda lime glass (SLG/Mo) substrates, using physical vapor deposition (PVD) 3-stage process. The Mo thin films were sputtered on SLG substrates using DC planar magnetron sputtering at a working gas (Ar) pressure that varies from 0.8 mT to 12 mT with a sputtering power density of 1.2 W/cm{sub 2}. The sputtering pressure of Mo thin films was varied in order to induce variations in the sputtered films morphology and porosity; as well as to subsequently induce variations in the Na out-diffusion from SLG substrate. The surface chemistry of CIGS thin films was investigated by X-Ray Photoelectron Spectroscopy (XPS). The XPS surface surveys (top 30A) and depth profiling survey (top 100A) for the elements, their chemical states, and their relative concentration were analyzed for CIGS thin films. The XPS surface analysis and composition of CIGS thin films were correlated to the bulk composition and Na out-diffusion in the CIGS films from SLG substrates.

14 SOLAR ENERGY↗

ULTRA-LOW-ENERGY HIGH-CURRENT ION SOURCE

The technical objective of the project was to develop an ultra-low-energy, high-intensity ion source (ULEHIIS) for materials processing in high-technology fields including semiconductors, micro-magnetics and optics/opto-electronics. In its primary application, this ion source can be incorporated into the 4Wave thin-film deposition technique called biased target ion-beam deposition (BTIBD), which is a deposition technique based on sputtering (without magnetic field, i.e., not the typical magnetron sputtering). It is a technological challenge because the laws of space charge limited current (Child-Langmuir) set strict limits of how much current can be extracted from a reservoir of ions, such as a suitable discharge plasma. The solution to the problem was an innovative dual-discharge system without the use of extraction grids.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Local structure investigation of Co doped ZnO thin films prepared by RF sputtering technique

Co doped ZnO thin films have been prepared using rf magnetron sputtering technique with varying Co doping concentration. GIXRD has been used to probe long range order and Zn, Co and Oxygen K-edge XAFS measurements have been used for investigating local structure around Zn and Co atoms. GIXRD results show wurzite structure of the samples while XANES and EXAFS results at Zn and Co K edge show that Co is going at Zn site in ZnO matrix and no other phase is present. These results are further confirmed by O K edge and Co L{sub 2,3} edge XANES measurements.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ion Source of Pure Single Charged Boron Based on Planar Magnetron Discharge in Self-Sputtering Mode

A planar magnetron sputtering device with thermally isolated sintered boron target has been designed and demonstrated. The magnetron is intended to use for generation of boron ion beams, as well as in plasma immersion implantation. For a boron target, high target temperature is required because boron has low electrical conductivity at room temperature, which increases with temperature. The target is well insulated thermally and can be heated by an initial low-current, high-voltage DC discharge mode. A discharge power of 16 W was adequate to reach the required surface temperature, after that a transition of the discharge to a high-current, low-voltage mode is observed. Applying high current pulses over the DC heating discharge results in a self-sputtering operational mode of the magnetron discharge. Ion beam was extracted from the discharge plasma. Beam analysis was performed with a time-of-flight system. All the boron ions are single charged. The maximum boron ion fraction in the beam is greater than 99%, and the mean boron ion fraction, time-integrated over the whole pulse length, is about 95%. This kind of boron ion source could be competitive to conventional boron ion sources that utilize compounds such as BF{sub 3}, and could be useful for semiconductor industry application.

36 MATERIALS SCIENCE↗

High-Rate Sputter Deposition of Ultrathick Boron Carbide Coatings on Rolling Spherical Substrates

Amorphous boron carbide (B 4 C) is a promising next-generation ablator material for inertial confinement fusion. However, the deposition of ultrathick B4C coatings with submicron-scale density uniformity on spherical substrates, as required for ablator shell fabrication, remains challenging. Here, in this study, we use direct current magnetron sputtering to deposit B 4 C onto 2-mm-diameter Si spheres rolling in a dish-shaped substrate holder. High deposition rates of ∼3 μm/h are achieved. Ultrathick films have a columnar microstructure, with the column width determined by the density of nodular defects. Nodular defect nucleation is dominated by the pickup of particulates from the holder during substrate rolling. We demonstrate the fabrication of a hollow B 4 C spherical shell with a wall thickness of 80 μm. Also demonstrated is the laser machining of holes in the B 4 C coating, which is necessary for both the chemical removal of the Si template and the attachment of a fusion fuel fill tube.

Inertial confinement fusion targets↗

Combinatorial sputter deposition of ultrathick Au-Bi alloy films

We report gold-bismuth alloys are of interest as catalysts and catalytic sensing systems, electrochemical sensors, superconductors, and hohlraums for magnetically assisted inertial confinement fusion implosions. Radiation-hydrodynamics simulations with the Lasnex code of laser-driven hohlraums predict higher x-ray drive from Au-Bi alloys compared with cases of Au-Ta or pure Au and Bi hohlraums. Here, we use direct current magnetron sputtering in Ar gas, with co-sputtering from two elemental targets, to deposit Au-Bi alloys with Bi content of 9–77 at.% and thicknesses up to ~20 µm. Films are characterized by a combination of x-ray diffraction, Rutherford backscattering, scanning electron microscopy, substrate-curvature-based residual stress, and electronic transport measurements. Experiments are complemented by Monte Carlo simulations of ballistic sputtering and gas phase transport of depositing species and Ar gas atoms. Results show that all films are polycrystalline, with three distinct compositional regimes dominated by Au, Au 2 Bi, and Bi crystallographic phases. A metallic behavior of the temperature dependence of electrical resistivity is observed for all the films. Films with Bi content above ~30 at.% exhibit porosity, which is tolerable to hohlraum x-ray drive based on Lasnex simulations.

36 MATERIALS SCIENCE↗