Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNESIUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Friction-based riveting technique for AZ31 magnesium alloy

Rivet materials used in the aerospace and automotive industries are typically alloys of aluminum (Al) or steel. Magnesium (Mg) is an attractive alternative because it is 33% and 75% lighter than Al and steel, respectively. However, a primary barrier for using Mg as rivet material is its poor formability at room temperature, resulting in brittle fracture of the rivet head during cold riveting. Hot riveting is possible but suffers from high cycle time due to the need for pre-heating. A new friction-based riveting technique, Rotating Hammer Riveting (RHR), is reported to fully form AZ31 Mg rivet heads in a mere 0.23 seconds cycle time. Heat and pressure generated through severe plastic deformation during the process was sufficient to form the Mg rivet head without the need for a separate pre-heating operation. Due to dynamic recrystallization, AZ31 Mg grains in the rivet head were significantly refined from about 15 to 2.6 µm during RHR, which favors the formability of Mg rivet by triggering grain boundary sliding and reducing plastic anisotropy of Mg. In addition, RHR joints showed a metallurgical bond between the rivet head and top sheet, which eliminates a significant pathway for corrosion.

36 MATERIALS SCIENCE↗

A combined experimental and crystal plasticity study of grain size effects in magnesium alloys

This work presents a method to incorporate the micro Hall-Petch equation into the crystal plasticity finite element (CPFE) framework accounting for the microstructural features to understand the coupling between grain size, texture, and loading direction in magnesium alloys. The effect of grain size and texture is accounted for by modifying the slip resistances of individual basal and prismatic systems based on the micro Hall-Petch equation. The modification based on the micro Hall-Petch equation endows every slip system at each microstructural point with a slip system-level grain size and maximum compatibility factor, which are in turn used to modify the slip resistance. While the slip-system level grain size is a measure of the grain size, the maximum compatibility factor encodes the effect of the grain boundary on the slip system resistance modification and is computed based on the Luster-Morris factor. The model is calibrated using experimental stress-strain curves of Mg-4Al samples with three different grain sizes from which the Hall-Petch coefficients are extracted and compared with Hall-Petch coefficients predicted using original parameters from previous work. The predictability of the model is then evaluated for a Mg-4Al sample with different texture and three grain sizes subjected to loading in different directions. The calibrated parameters are then used for some parametric studies to investigate the variation of Hall-Petch slope for different degrees of simulated spread in basal texture, variation of Hall-Petch slope with loading direction relative to basal poles for a microstructure with strong basal texture, and variation of yield strength with change in grain morphology. The proposed approach to incorporate the micro Hall-Petch equation into the CPFE framework provides a foundation to quantitatively model more complicated scenarios of coupling between grain size, texture and loading direction in the plasticity of Mg alloys.

Crystal plasticity↗

Direct observation of annealing-driven recrystallization behavior in magnesium alloy at low strain condition

Grain-twin interactions are significant in texture modification under thermodynamic driving force. In this study, annealing-driven twinning/detwinning behavior, grain growth, and corresponding texture evolution in a pre-deformed AZ31 magnesium alloy were systematically tracked and investigated via in-situ heating synchrotron X-ray diffraction and quasi in-situ electron backscattered diffraction techniques. A twinning texture is generated in the pre-deformed sample due to the activation of {$10\bar{1}2$} tensile twinning. During annealing, dislocation annihilation occurs between 100 and 280 °C, and recrystallization occurs above 280 °C, manifesting as the initial residual matrix and twins being competitively swallowed by each other, forming a bimodal texture. The recrystallization process is completed by boundary movement, which depends on the energy difference across the boundary. In addition, it is found that the grain boundaries favor movement towards the side with higher stored energy, regardless of the boundary type or the boundary energy.

In-situ observation↗

Integrated process-structure–property–performance optimization of cold-sprayed zinc coatings on AZ91 magnesium alloy

High-pressure die cast (HPDC) AZ91 magnesium alloy is widely used in automotive components such as transmission housings and brackets for its excellent strength-to-weight ratio. Zinc-based cold spray coatings can be applied selectively to vulnerable areas to enhance corrosion resistance, minimize galvanic coupling with dissimilar metals, and eliminate the need for full-surface oxide coatings, making the process more efficient and targeted. A comprehensive evaluation of 16 combinations of nitrogen carrier gas temperatures and pressures led to the identification of an optimal range of process parameters, yielding Zn coatings with porosity <0.5 % by area, wear rates reduced by a factor of two compared to uncoated AZ91, and adhesion strengths up to 35 MPa. The enhanced mechanical performance of the coating is attributed to the low porosity and the formation of a metallurgical bond at the coating-substrate interface. Corrosion studies using macroscale potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS) revealed a significant decrease in corrosion rate and a shift to more noble corrosion potentials (ZCP) for coated substrates. Furthermore, the Zn cold-sprayed samples exhibited significantly lower corrosion-induced evolved hydrogen content compared to the base AZ91 substrate and AZ91 coated with industrial coatings, demonstrating that the Zn layer effectively protects the substrate from the corrosive environment. Overall, cold spray Zn coatings significantly improve the mechanical and corrosion performance of AZ91 Mg alloys, addressing key material challenges and enabling their broader use in automotive applications.

Corrosion performance↗

Joining sheet aluminum AA6061-T4 to cast magnesium AM60B by vaporizing foil actuator welding: Input energy, interface, and strength

Dissimilar joining of sheet aluminum AA6061-T4 to cast magnesium AM60B was achieved by vaporizing foil actuator welding (VFAW). Three input energy levels were used (6, 8, and 10 kJ), and as a trend, higher input energies resulted in progressively higher flyer velocities, more pronounced interfacial wavy features, larger weld zones, higher peel strengths, and higher peel energies. In all cases, weld cross section revealed a soundly bonded interface characterized by well-developed wavy features and lack of voids and continuous layers of intermetallic compounds (IMCs). At 10 kJ input energy, flyer speed of 820 m/s, peel strength of 22.4 N/mm, and peel energy of 5.2 J were obtained. In lap-shear, failure occurred in AA6061- T4 flyer at 97% of the base material’s peak tensile load. Peel samples failed along the weld interface, and the AM60B-side of the fracture surface showed thin, evenly-spaced lines of Al residuals which had been torn out of the base AA6061-T4 in a ductile fashion and transferred over to the AM60B side, indicating very strong AA6061-T4/AM60B bond in these areas. Furthermore, this work demonstrates VFAW’s capability in joining dissimilar lightweight metals such as Al/Mg, which is expected to be a great enabler in the ongoing push for vehicle weight reduction.

36 MATERIALS SCIENCE↗

Stabilizing magnesium plating by a low-cost inorganic surface membrane for high-voltage and high-power Mg batteries

Mg batteries with halide-free electrolytes suffer from poor stability of the Mg metal anode due to electrolyte decomposition. Here, we report a low-cost zeolite membrane supported on Mg to address this challenge. It vastly reduces the population (hence decomposition) of free diglyme at the Mg/electrolyte interface, while allowing facile transport of Mg 2+ cations through the membrane. We demonstrate dendrite-free Mg plating/stripping performance in a magnesium tetrakis(hexafluoroisopropyloxy)borate/diglyme electrolyte with a 750-fold extended lifetime (over 6,000 h) and a high coulombic efficiency of ~98%. The prototype Mo 3 S 4 cathode paired with the protected Mg anode shows 91% capacity retention over 200 cycles. Importantly, this membrane protects soluble species in a high-voltage organic polymer cathode from being reduced at the anode via shuttling, achieving a full cell with a 3.5 V cutoff voltage. This results in a high specific energy density of 320 Wh kg –1 and a power density of 1,320 W kg –1 based on cathode mass.

25 ENERGY STORAGE↗

A magnesium-carboxylate framework showing luminescent sensing for CS{sub 2} and nitroaromatic compounds

A magnesium metal-organic framework compound, namely [NH{sub 2}(CH{sub 3}){sub 2}][Mg{sub 3}(NDC){sub 2.5}(HCO{sub 2}){sub 2}(DMF){sub 0.75}(H{sub 2}O){sub 0.25}]·1.25DMF·0.75H{sub 2}O (1) (H{sub 2}NDC=1,4-naphthalene dicarboxylic acid, DMF=N,N′-dimethylformamide), has been synthesized in solvothermal conditions and structurally characterized. It features a three-dimensionally anionic framework with aligned channels parallel to the b-axis. Luminescent studies indicated that it showed significant luminescence quenching for carbon disulfide (CS{sub 2}) and nitrobenzene after being activated, at a content of only 3.0 and 0.1 vol% in DMF, respectively. In addition, the activated sample showed sensitive luminescence quenching for 1,3,5-trinitrophenol with a low concentration of 5×10{sup −5} mol/L. - Graphical abstract: Presented is a microporous 3D Mg-MOF, namely, [NH{sub 2}(CH{sub 3}){sub 2}][Mg{sub 3}(NDC){sub 2.5}(HCO{sub 2}){sub 2}(DMF){sub 0.75}(H{sub 2}O){sub 0.25}]·1.25DMF·0.75H{sub 2}O (1) (H{sub 2}NDC=1,4-naphthalene dicarboxylic acid) showing significant luminescence quenching for carbon disulfide and nitrobenzene. - Highlights: • A microporous 3D metal-organic framework based on Mg. • The compound shows significant luminescence quenching for CS{sub 2} and nitrobenzene after activated. • The compound shows sensitive luminescence quenching for 1,3,5-trinitrophenol with a low concentration of 5×10{sup −5} mol/L.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Research on microstructures of sub-rapidly solidified AZ61 Magnesium Alloy

AZ61 magnesium alloy foils of 0.5-3.0 mm thick were successfully produced by using sub-rapid solidification technique. Microstructures of conventionally solidified (CS) and sub-rapidly solidified (sub-RS) alloys were examined by optical microscope (OM) and scanning electron microscope (SEM). The results showed that the cellular grain of 1.8-13.5 {mu}m can be obtained during sub-rapid solidification process. Phase compositions and microdistribution of the alloying elements in the foils were analyzed by X-ray diffraction (XRD) and electron probe microanalyzer (EPMA), respectively. The eutectic transformation L {yields} {alpha}-Mg + {beta}-Mg{sub 17}Al{sub 12} and microsegregation in conventionally solidified AZ61 alloy were remarkably suppressed in sub-rapid solidification process. As a consequence, the alloying elements Al, Zn, Mn showed much higher solid solubility and the sub-rapid solidification microstructures dominantly consisted of supersaturated {alpha}-Mg solid solution. Meanwhile, the {beta}-Mg{sub 17}Al{sub 12} phases located in the {alpha}-Mg grain boundaries are largely decreased due to high solidification cooling rate.

36 MATERIALS SCIENCE↗

Corrosion behavior of Ti-Al-N/Ti-Al duplex coating on AZ31 magnesium alloy in NaCl aqueous solution

In this study, Ti-Al-N/Ti-Al duplex coating was deposited on AZ31 magnesium alloy by magnetron sputtering with a Ti/Al composite target. Scanning electron microscopy and Auger electron spectroscopy were applied to investigate the morphology and elemental concentration of the obtained coating, respectively. The top layer was Ti-Al-N film with a Ti:Al:O:N ratio of 0.32:0.84:0.08:1, and the bottom layer was Ti-Al film with a Ti:O:Al ratio of 1.94:0.12:1. Each layer of this coating presented a developed columnar structure. The polarization test and immersion test were used to investigate corrosion behavior of the coated sample in 3.5 wt.% NaCl aqueous solution. The results showed that this duplex coating could protect the substrate effectively in NaCl aqueous solution. Nevertheless, several through-thickness micropores in the coating finally induced the failure of the coated AZ31 in the immersion test.

36 MATERIALS SCIENCE↗

Microstructural stability and creep properties of die casting Mg-4Al-4RE magnesium alloy

The AE44 (Mg-4Al-4RE) alloy was prepared by a hot-chamber die casting method. The microstructure, microstructural stability and creep properties at 175 deg. C were investigated. The microstructure was analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and the Rietveld method. The results show that die cast AE44 magnesium alloy consists of {alpha}-Mg, Al{sub 11}RE{sub 3}, Al{sub 2}RE and Al{sub 2.12}RE{sub 0.88} phases. The Al{sub 11}RE{sub 3} phase is thermally stable at 175 deg. C whereas the metastable Al{sub 2.12}RE{sub 0.88} phase undergoes a transition into the equilibrium Al{sub 2}RE phase. The alloy investigated is characterized by good creep properties at temperatures of 175 deg. C and 200 {sup o}C.

36 MATERIALS SCIENCE↗

Effect of heat input on the microstructure and mechanical properties of tungsten inert gas arc butt-welded AZ61 magnesium alloy plates

In this paper, the effects of heat input on the microstructures and mechanical properties of tungsten inert gas arc butt-welded AZ61 magnesium alloy plates were investigated by microstructural observations, microhardness tests and tensile tests. The results show that with an increase of the heat input, the grains both in the fusion zone and the heat-affected zone coarsen and the width of the heat-affected zone increased. Moreover, an increase of the heat input resulted in a decrease of the continuous {beta}-Mg{sub 17}Al{sub 12} phase and an increase of the granular {beta}-Mg{sub 17}Al{sub 12} phase in both the fusion zone and the heat-affected zone. The ultimate tensile strength of the welded joint increased with an increase of the heat input, while, too high a heat input resulted in a decrease of the ultimate tensile strength of the welded joint. In addition, the average microhardness of the heat-affected zone and fusion zone decreased sharply with an increase of the heat input and then decreased slowly at a relatively high heat input.

36 MATERIALS SCIENCE↗

Study on the corrosion residual strength of the 1.0 wt.% Ce modified AZ91 magnesium alloy

The effect of corrosion on the tensile behaviour of the 1.0 wt.% Ce modified AZ91 magnesium alloy was investigated by the immersion of the test bar in 3.5 wt.% NaCl aqueous solution for 0, 12, 40, 108, 204, 372 and 468 h with the subsequent tensile tests in this paper. The fractography was analyzed by scanning electron microscopy. The results show that pitting corrosion should be responsible for the drop of the corrosion residual strength within the testing time. The depth of the corrosion pits was statistically and quantitatively obtained by an optical microscopy and the maximal value was recorded as the extreme depth of the corrosion pit. Furthermore, the corrosion residual strength is linearly dependent on the extreme depth of the corrosion pit, which can be attributed to the loss of cross-sectional area and the emergence of stress concentration caused by the initiation and development of corrosion pits.

36 MATERIALS SCIENCE↗

Abnormal distribution of microhardness in tungsten inert gas arc butt-welded AZ61 magnesium alloy plates

In this study, the effects of heat input on the distribution of microhardness of tungsten inert gas (TIG) arc welded hot-extruded AZ61 magnesium alloy joints were investigated. The results show that with an increase of heat input, the distributions of microhardness at the top and bottom of the welded joints are different because they are determined by both the effect of grain coarsening and the effect of dispersion strengthening. With an increase of the heat input, the microhardness of the heat-affected zone (HAZ) at the top and bottom of welded joints and the fusion zone (FZ) at the bottom of welded joints decreased gradually, while the microhardness of the FZ at the top of welded joints decreased initially and then increased sharply. The reason for the abnormal distribution of microhardness of the FZ at the top of the welded joints is that this area is close to the heat source during welding and then large numbers of hard {beta}-Mg{sub 17}(Al,Zn){sub 12} particles are precipitated. Hence, in this case, the effect of dispersion strengthening dominated the microhardness.

36 MATERIALS SCIENCE↗

Characterization of AZ31B wrought magnesium alloy joints welded by high power fiber laser

A 6 kW fiber laser is used to weld AZ31B wrought magnesium alloy and the characterization of welded joints are studied by the observations of bead size, microstructure and mechanical properties. The accepted joints without macro-defects can be obtained when the laser power is in the range of 2.5 to 4.0 kW. Typical hexagonal dendrites are observed in the fusion zone, whose average semi-axis length increases with increasing heat input or decreasing welding speed. The minimum ultimate tensile strength of welded joints reaches 227 MPa, 94.6% of the base metal. And when the heat input reduces to 48 J/mm or lower, the joints are fractured in the base metal, showing stronger failure strength compared to the base metal. For the joints ruptured in the weld metal, the fracture surface is characterized by a ductile-brittle mixed pattern consisting of both dimples and cleavages. Finally, the formation mechanism of pore in the welds is discussed and summarized by the pore morphologies on the fracture surface. - Highlights: {yields} Accepted joints of AZ31B Mg alloy are produced by high power fiber laser. {yields} Optimal welding parameters are summarized by experimental observations. {yields} Obvious hexagonal dendrites are observed in the fusion zone. {yields} The joints are stronger than base metal as the heat input is lower than 48 J/mm. {yields} Pore formation mechanism of welded joints is discussed and summarized.

36 MATERIALS SCIENCE↗

Microstructural and textural evolution of AZ61 magnesium alloy sheet during bidirectional cyclic bending

In this work, the microstructural and textural evolution in the sheets of AZ61 magnesium alloy was studied by means of bidirectional cyclic bending for 8 passes at 623 K. The bended samples were examined by optical microscopy and electron backscatter diffraction analysis. The results showed that a gradient structure with fine grains about 3 μm in the regions near two surfaces and, in contrast, coarse grains in the middle of the sheet were formed. The evident grain refinement was attributed to twin-assisted dynamic recrystallization and continuous dynamic recrystallization induced by kink bands. The texture intensity was clearly reduced, resulting in a negative gradient distribution, with the texture intensity decreases from the center of the sheet to two surfaces. The weakened texture greatly facilitated the reduction of the yield strength. A higher fracture elongation and a slightly improved ultimate tensile strength were achieved concurrently. - Highlights: • The AZ61 Mg alloy is deformed at 623 K by bidirectional cyclic bending. • A symmetric gradient distribution of fine grains along the thickness is formed. • The basal texture in the regions near two surfaces is weakened significantly.

36 MATERIALS SCIENCE↗

Microstructure stability of ultra-fine grained magnesium alloy AZ31 processed by extrusion and equal-channel angular pressing (EX–ECAP)

Thermal stability of the ultra-fine grained (UFG) microstructure of magnesium AZ31 alloy was investigated. UFG microstructure was achieved by a combined two-step severe plastic deformation process: the extrusion (EX) and subsequent equal-channel angular pressing (ECAP). This combined process leads to refined microstructure and enhanced microhardness. Specimens with UFG microstructure were annealed isochronally at temperatures 150–500 °C for 1 h. The evolution of microstructure, mechanical properties and dislocation density was studied by electron backscatter diffraction (EBSD), microhardness measurements and positron annihilation spectroscopy (PAS). The coarsening of the fine-grained structure at higher temperatures was accompanied by a gradual decrease of the microhardness and decrease of dislocation density. Mechanism of grain growth was studied by general equation for grain growth and Arrhenius equation. Activation energies for grain growth were calculated to be 115, 33 and 164 kJ/mol in temperature ranges of 170–210 °C, 210–400 °C and 400–500 °C (443–483 K, 483–673 K and 673–773 K), respectively. - Highlights: • Microhardness of UFG AZ31 alloy decreases with increasing annealing temperature. • This fact has two reasons: dislocation annihilations and/or grain growth. • The activation energies for grain growth were calculated for all temperature ranges.

36 MATERIALS SCIENCE↗

Effect of intermediate annealing on the microstructure and mechanical property of ZK60 magnesium alloy produced by twin roll casting and hot rolling

Twin roll cast (designated as TRC in short) ZK60 magnesium alloy strip with 3.5 mm thickness was used in this paper. The TRC ZK60 strip was multi-pass rolled at different temperatures, intermediate annealing heat treatment was performed when the thickness of the strip changed from 3.5 mm to 1 mm, and then continued to be rolled until the thickness reached to 0.5 mm. The effect of intermediate annealing during rolling process on microstructure, texture and room temperature mechanical properties of TRC ZK60 strip was studied by using OM, TEM, XRD and electronic universal testing machine. The introduction of intermediate annealing can contribute to recrystallization in the ZK60 sheet which was greatly deformed, and help to reduce the stress concentration generated in the rolling process. Microstructure uniformity and mechanical properties of the ZK60 alloy sheet were also improved; in particular, the room temperature elongation was greatly improved. When the TRC ZK60 strip was rolled at 300 °C and 350 °C, the room temperature elongation of the rolled sheet with 0.5 mm thickness which was intermediate annealed during the rolling process was increased by 95% and 72% than that of no intermediate annealing, respectively. - Highlights: • Intermediate annealing was introduced during hot rolling process of twin roll cast ZK60 alloy. • Intermediate annealing can contribute to recrystallization and reduce the stress concentration in the deformed ZK60 sheet. • Microstructure uniformity and mechanical properties of the ZK60 sheet were improved, in particular, the room temperature elongation. • The elongation of the rolled ZK60 sheet after intermediate annealed was increased by 95% and 72% than that of no intermediate annealing.

36 MATERIALS SCIENCE↗

Thermal stability of bimodal microstructure in magnesium alloy AZ91 processed by ECAP

The changes in microstructure of equal channel angular pressing (ECAP) processed magnesium alloy AZ91 during thermal exposure were studied in this paper. The microstructure stability was investigated by means of electron backscatter diffraction (EBSD), which allowed to measure the changes in grain size, mutual ratio of low-angle boundaries (LABs) to high-angle ones (HABs) and local lattice distortion evaluated by the kernel average misorientation (KAM) parameter. It was found experimentally that the threshold temperature at which significant grain coarsening takes place is 350 °C. No modification to mean grain diameter occurs below this temperature, nonetheless, some changes in LAB and HAB fraction, as well as in local lattice distortion, can be observed. - Highlights: • Thermal stability of bimodal UFG AZ91 alloy was assessed by means of EBSD. • Threshold temperature for pronounced grain coarsening was found at 350 °C. • Below 350 °C increase in LAB fraction and local lattice distortion takes place. • Local lattice distortion (LLD) can be well described using KAM approach. • LLD is influenced by coarsening and precipitation of Mg{sub 17}Al{sub 12} particles.

36 MATERIALS SCIENCE↗