Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “JET FLAP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Comparison of predictions and under-the-wing EBF noise data

Detailed three-dimensional free field noise data were obtained by NASA for an under-the-wing externally blown model three-flap wing, and for a similar slotless wing. Spatial (polar and azimuthal) and spectral characteristics of these data are presented. These data are compared with predictions from some published EBF noise calculation methods. Methods include the totally empirical ANOPP and GELAC procedures, and a semi-empirical noise component method. The latter method adds the separately computed dipole noise due to fluctuating lift and drag, trailing edge noise, and quadrupole noise due to the deflected jet. Each of these components is calculated for the local geometry and flow conditions.

Fink, M. R.↗
NASA NTRS2004

Ballistic Impact of Braided Composites With a Soft Projectile

Impact tests using a soft gelatin projectile were performed to identify failure modes that occur at high strain energy density during impact loading. Use of a soft projectile allows a large amount of kinetic energy to be transferred into strain energy in the target before penetration occurs. Failure modes were identified for flat aluminum plates and for flat composite plates made from a triaxial braid having a quasi-isotropic fiber architecture with fibers in the 0 and +/- 60 deg. directions. For the aluminum plates, a large hole formed as a result of crack propagation from the initiation site at the center of the plate to the fixed boundaries. For the composite plates, fiber tensile failure occurred in the back ply at the center of the plate. Cracks then propagated from this site along the +/- 60 deg. fiber directions until triangular flaps opened to allow the projectile to pass through the plate. The damage size was only slightly larger than the initial impact area. It was difficult to avoid slipping of the fixed edges of the plates during impact, and slipping was shown to have a large effect on the penetration threshold. Failure modes were also identified for composite half-rings fabricated with the 0 deg. fibers aligned circumferentially. Slipping of the edges was not a problem in the half-ring tests. For the composite half-rings, fiber tensile failure also occurred in the back ply. However, cracks initially propagated from this site in a direction transverse to the 0 deg. fibers. The cracks then turned to follow the +/- 60 deg. fibers for a short distance before turning again to follow 0 deg. fibers until two approximately rectangular flaps opened to allow the projectile to pass through the plate. The damage size in the composite half-rings was also only slightly larger than the initial impact area. Cracks did not propagate to the boundaries, and no delamination was observed. The damage tolerance demonstrated by the quasi-isotropic triaxial braid composites indicate that composites of this type can reasonably be considered as a lightweight alternative to metals for fan cases in commercial jet engines.

Roberts, Gary D.↗
NASA NTRS1991

Air turbo-ramjet engine

A jet engine designed to power a supersonic airplane throughout a range of speeds from subsonic to high supersonic includes a housing which bounds an internal passage having in succession a fixed-area inlet section, a diverging passage section, a mixing section, a combustion section, and an outlet section. A fan rotor rotates in the inlet section and includes a plurality of rotor blade members. The housing includes a main body and at least one flap which is movable between one end position in which it externally bounds a portion of the diverging passage section and another end position in which it externally delimits a diverging discharge passage connecting the diverging passage section with the exterior of the housing. The cross-sectional area of the outlet section is adjustable. The rotor is driven in rotation by a fuel/oxygen powered turbine the outlet of which communicates with the mixing section, but the driving action of the turbine is discontinued at actual supersonic velocities exceeding a predetermined supersonic velocity. The pitch of at least one element of each of the rotor blade members is adjustable.

Kepler, Charles E.↗
NASA NTRS1975

Diagnostic calculations of airframe-radiated noise

Methods of calculating airframe noise due to the following components are presented: wings and stabilizers, flaps, landing gear 'self-noise', landing gear bay (wheel well) oscillations, separated flow interaction with edges of cavities, and doors associated with gear deployment. The predominant source mechanisms were dipole-like in nature, being related to the local fluctuating aerodynamic forces on struts, airfoil edges, cavity edges, etc. Available data are converted into semiempirical prediction methods to enable a tentative rank ordering of noise sources. A sample application of these prediction procedures is carried out for a typical CTOL passenger jet using actual aircraft parameters, where available.

Hayden, R. E.↗
NASA NTRS1975

Flight test investigation of the vortex wake characteristics behind a Boeing 727 during two-segment and normal ILS approaches

A series of flight tests were performed to evaluate the vortex wake characteristics of a Boeing 727 (B727-200) aircraft during conventional and two-segment ILS approaches. Flights of the B727, equipped with smoke generators for vortex marking, were flown wherein its vortex wake was intentionally encountered by a Lear Jet model 23 (LR-23) or a Piper Twin Comanche (Pa-30); and its vortex location during landing approach was measured using a system of photo-theodolites. The tests showed that at a given separation distance there were no differences in the upsets resulting from deliberate vortex encounters during the two types of approaches. Timed mappings of the position of the landing configuration vortices showed that they tended to descend approximately 91 meters (300 feet) below the flight path of the B727. The flaps of the B727 have a dominant effect on the character of the trailed wake vortex. The clean wing produces a strong, concentrated vortex. As the flaps are lowered, the vortex system becomes more diffuse. Pilot opinion and roll acceleration data indicate that 4.5 nautical miles would be a minimum separation distance at which roll control could be maintained during parallel encounters of the B727's landing configuration wake by small aircraft.

Garodz, L. J.↗
NASA NTRS1981

Fuel-Conservation Guidance System for Powered-Lift Aircraft

A technique is described for the design of fuel-conservative guidance systems and is applied to a system that was flight tested on board NASA's sugmentor wing jet STOL research aircraft. An important operational feature of the system is its ability to rapidly synthesize fuel-efficient trajectories for a large set of initial aircraft positions, altitudes, and headings. This feature allows the aircraft to be flown efficiently under conditions of changing winds and air traffic control vectors. Rapid synthesis of fuel-efficient trajectories is accomplished in the airborne computer by fast-time trajectory integration using a simplified dynamic performance model of the aircraft. This technique also ensures optimum flap deployment and, for powered-lift STOL aircraft, optimum transition to low-speed flight. Also included in the design is accurate prediction of touchdown time for use in four-dimensional guidance applications. Flight test results have demonstrated that the automatically synthesized trajectories produce significant fuel savings relative to manually flown conventional approaches.

Erzberger, Heinz↗
NASA NTRS1990

Large-scale wind tunnel studies of a jet-engined powered ejector-lift STOVL aircraft

A full-scale model of a supersonic STOVL single engine flighter aircraft employing an ejector to augment lift in hover and in low-speed flight was tested in the 40- by 80-ft and 80- by 120-ft test sections of the National Full-Scale Aerodynamics Complex located at the NASA Ames Research Center. The measured ejector augmentation ratio in hover met the design requirement of 1.6 and continued to provide the lift necessary in forward flight for good transition qualities. The up-and-away aerodynamics (ejector system stowed) were found to be conventional for this class of vehicle. The pitch control provided by the full-span blown flaps is sufficient to control the large pitching moments generated by ventral exhaust nozzle vectoring and propulsion induced aerodynamic effects such as the turning of the flow entrained into the ejectors.

Dudley, Michael R.↗
NASA NTRS1993

Performance characteristics of two multiaxis thrust-vectoring nozzles at Mach numbers up to 1.28

The thrust-vectoring axisymmetric (VA) nozzle and a spherical convergent flap (SCF) thrust-vectoring nozzle were tested along with a baseline nonvectoring axisymmetric (NVA) nozzle in the Langley 16-Foot Transonic Tunnel at Mach numbers from 0 to 1.28 and nozzle pressure ratios from 1 to 8. Test parameters included geometric yaw vector angle and unvectored divergent flap length. No pitch vectoring was studied. Nozzle drag, thrust minus drag, yaw thrust vector angle, discharge coefficient, and static thrust performance were measured and analyzed, as well as external static pressure distributions. The NVA nozzle and the VA nozzle displayed higher static thrust performance than the SCF nozzle throughout the nozzle pressure ratio (NPR) range tested. The NVA nozzle had higher overall thrust minus drag than the other nozzles throughout the NPR and Mach number ranges tested. The SCF nozzle had the lowest jet-on nozzle drag of the three nozzles throughout the test conditions. The SCF nozzle provided yaw thrust angles that were equal to the geometric angle and constant with NPR. The VA nozzle achieved yaw thrust vector angles that were significantly higher than the geometric angle but not constant with NPR. Nozzle drag generally increased with increases in thrust vectoring for all the nozzles tested.

Wing, David J.↗
NASA NTRS1976

Characteristics of wake vortex generated by a Boeing 727 jet transport during two-segment and normal ILS approach flight paths

A series of flight tests was conducted to evaluate the vortex wake characteristics of a Boeing 727 (B727-200) aircraft during conventional and two-segment ILS approaches. Twelve flights of the B727, which was equipped with smoke generators for vortex marking, were flown and its vortex wake was intentionally encountered by a Lear Jet model 23 (LR-23) and a Piper Twin Comanche (PA-30). Location of the B727 vortex during landing approach was measured using a system of photo-theodolites. The tests showed that at a given separation distance there were no readily apparent differences in the upsets resulting from deliberate vortex encounters during the two types of approaches. Timed mappings of the position of the landing configuration vortices showed that they tended to descend approximately 91 m(300 ft) below the flight path of the B727. The flaps of the B727 have a dominant effect on the character of the trailed wake vortex. The clean wing produces a strong, concentrated vortex but as the flaps are lowered, the vortex system becomes more diffuse. Pilot opinion and roll acceleration data indicate that 4.5 n.mi. would be a minimum separation distance at which roll control of light aircraft (less than 5,670 kg (12,500 lb) could be maintained during parallel encounters of the B727's landing configuration wake. This minimum separation distance is generally in scale with results determined from previous tests of other aircraft using the small roll control criteria.

Kurkowski, R. L.↗
NASA NTRS1993

Numerical simulation of a powered-lift landing, tracking flow features using overset grids, and simulation of high lift devices on a fighter-lift-and-control wing

Attached as appendices to this report are documents describing work performed on the simulation of a landing powered-lift delta wing, the tracking of flow features using overset grids, and the simulation of flaps on the Wright Patterson Lab's fighter-lift-and-control (FLAC) wing. Numerical simulation of a powered-lift landing includes the computation of flow about a delta wing at four fixed heights as well as a simulated landing, in which the delta wing descends toward the ground. Comparison of computed and experimental lift coefficients indicates that the simulations capture the qualitative trends in lift-loss encountered by thrust-vectoring aircraft operating in ground effect. Power spectra of temporal variations of pressure indicate computed vortex shedding frequencies close to the jet exit are in the experimentally observed frequency range; the power spectra of pressure also provide insights into the mechanisms of lift oscillations. Also, a method for using overset grids to track dynamic flow features is described and the method is validated by tracking a moving shock and vortices shed behind a circular cylinder. Finally, Chimera gridding strategies were used to develop pressure coefficient contours for the FLAC wing for a Mach no. of 0.18 and Reynolds no. of 2.5 million.

Chawla, Kalpana↗
NASA NTRS1993

Prediction of leading-edge transition and relaminarization phenomena on a subsonic multi-element high-lift system

Boundary-layer transition and relaminarization may have a critical effect on the flow development about multi-element high-lift systems of subsonic transport jets with swept wings. The purpose of the research is to study these transition phenomena in the leading-edge region of the various elements of a high-lift system. The flow phenomena studied include transition to the attachment-line flow, relaminarization, and crossflow instability, and transition. The calculations are based on pressure distributions measured in flight on the NASA Transport Systems Research Vehicle (Boeing 737-100) at a wing station where the flow approximated infinite swept wing conditions. The results indicate that significant regions of laminar flow can exist on all flap elements in flight. In future flight experiments (planned for January-February, 1994) the extent of these regions, the transition mechanisms and the effect of laminar flow on the high-lift characteristics of the multi-element system will be further explored.

Vandam, C. P.↗
NASA NTRS1972

The development of an augmentor wing jet STOL research aircraft (modified C-8A). Volume 2: Analysis of contractor's flight test

The initial flight test phase of the modified C-8A airplane was conducted. The primary objective of the testing was to establish the basic airworthiness of the research vehicle. This included verification of the structural design and evaluation of the aircraft's systems. Only a minimum amount of performance testing was scheduled; this has been used to provide a preliminary indication of the airplane's performance and flight characteristics for future flight planning. The testing included flutter and loads investigations up to the maximum design speed. The operational characteristics of all systems were assessed including hydraulics, environmental control system, air ducts, the vectoring conical nozzles, and the stability augmentation system (SAS). Approaches to stall were made at three primary flap settings: up, 30 deg and 65 deg, but full stalls were not scheduled. Minimum control speeds and maneuver margins were checked. All takeoffs and landings were conventional, and STOL performance was not scheduled during this phase of the evaluation.

Skavdahl, H.↗
NASA NTRS1979

An experimental study of USB flap noise reduction through mean flow modification

The effect of mean flow modification on the noise production of upper surface blown flaps has been studied experimentally. Mean velocity profile at the nozzle exit was modified from the usual 'top-hat' shape to 'Gamma' and 'L'-shaped profiles. The 'L'-modification caused noise reduction around and above the peak frequency of the 'top-hat' spectrum when compared on an equal thrust per exit area basis. Modification to 'Gamma'-shaped profile resulted in a shift of the spectrum to lower frequencies and a lower overall noise reduction. These modifications alter the development of the large scale disturbances in the upper shear layer and trailing edge wake of the wall jet geometry.

Joshi, M. C.↗
NASA NTRS1974

A modified Newton-Raphson analysis of flight measurements of the trailing vortices of a heavy jet transport

A modified Newton-Raphson method has been used to determine the parameters in equations describing the vortex flow to obtain a best match with flight measurements of the flow behind the C-5A airplane. The flight measurements were made using a specially instrumented T-33 airplane which passed as closely as possible to the centers of the trailing vortices at several distances behind the C-5A airplane. The flight measurements were transformed to flow velocity relative to an inertial frame of reference. The assumed form of the flow consisted of the superposition of two counterrotating, finite core vortices. The positions of the vortex centers, their total circulation, the effective eddy viscosity and measurement bias were the parameters adjusted. The assumed form of vortex flow fit well the measured velocities for the numerous sets of data, both flaps up and down for the C-5A airplane. The resulting values of total circulation, however, were about two-thirds that expected of a wing with an elliptical loading. A partial explanation of the less than expected circulation is a dip in the spanwise lift distribution at the airplane's center line. The distance between the trailing vortices at the smallest times encountered is somewhat less than that expected for an elliptical wing loading.

Taylor, L. W., Jr.↗
NASA NTRS1935

Development of the NACA slot-lip aileron

An investigation of the undesirable delayed action, or lag, of the spoiler-type lateral control device led to the development of the NACA slot-lip aileron. The tests were made in the 7- by 10-foot wind tunnel with a 4- by 8-foot wing hinged at the tunnel jet boundary and taken of the motion of the control device under test and of the resulting wing motion. First, the lag, as affected by the fore-and-aft location of retractable ailerons or spoilers was determined. The lag was found to increase regularly as the spoiler was moved from the rear of the wing toward the front. Then a combination of spoilers and fixed slot was developed that, with the spoiler retracting into the forward part of the slot, reduced the time lag to a negligible value. In addition, an arrangement was developed using a hinged aileron-type flap as the upper portion, or lip, of a slot through the wing. This arrangement appears to be usable as a form of lateral control device that shows promise of giving improved control and stability at the high angles of attack through stall, with negligible lag, low control forces, and relatively simple construction.

Weick, Fred E↗
NASA NTRS1980

Experimental aerodynamic characteristics of two V/STOL fighter/attack aircraft configurations at Mach numbers from 0.4 to 1.4

A wind tunnel test was conducted to measure the aerodynamic characteristics of two horizontal attitude takeoff and landing V/STOL fighter/attack aircraft concepts. In one concept, a jet diffuser ejector was used for the vertical lift system; the other used a remote augmentation lift system (RALS). Wind tunnel tests to investigate the aerodynamic uncertainties and to establish a data base for these types of concepts were conducted over a Mach number range from 0.2 to 2.0. The present report covers tests, conducted in the 11 foot transonic wind tunnel, for Mach numbers from 0.4 to 1.4. Detailed effects of varying the angle of attack (up to 27 deg), angle of sideslip (-4 deg to +8 deg), Mach number, Reynolds number, and configuration buildup were investigated. In addition, the effects of wing trailing edge flap deflections, canard incidence, and vertical tail deflections were explored. Variable canard longitudinal location and different shapes of the inboard nacelle body strakes were also investigated.

Nelms, W. P.↗
NASA NTRS1976

EBF noise reduction through nozzle/flap positioning

Results are presented of an experimental and analytical study of the dependence of externally blown flap (EBF) noise on the relative position and shape of engine exhaust nozzle. Tests, conducted on a 1/15 scale model of a triple-slotted EBF system, indicate that a significant reduction (of up to 10 to 15 db for no forward speed case and of up to 5 to 10 db for forward speed case) is possible in the low frequency (around 63 Hz) region of the noise spectrum of the full scale device for small nozzle/flap separation distances. The overall acoustic performance, measured in PNdb, does not exhibit significant reductions. The analysis of the EBF noise is carried out for two limiting airfoil in a free jet. The analytical results also suggest that low frequency noise can be reduced by placing the nozzle close to the flow turning elements.

Kadman, Y.↗
NASA NTRS2007

Flight Testing an Iced Business Jet for Flight Simulation Model Validation

A flight test of a business jet aircraft with various ice accretions was performed to obtain data to validate flight simulation models developed through wind tunnel tests. Three types of ice accretions were tested: pre-activation roughness, runback shapes that form downstream of the thermal wing ice protection system, and a wing ice protection system failure shape. The high fidelity flight simulation models of this business jet aircraft were validated using a software tool called "Overdrive." Through comparisons of flight-extracted aerodynamic forces and moments to simulation-predicted forces and moments, the simulation models were successfully validated. Only minor adjustments in the simulation database were required to obtain adequate match, signifying the process used to develop the simulation models was successful. The simulation models were implemented in the NASA Ice Contamination Effects Flight Training Device (ICEFTD) to enable company pilots to evaluate flight characteristics of the simulation models. By and large, the pilots confirmed good similarities in the flight characteristics when compared to the real airplane. However, pilots noted pitch up tendencies at stall with the flaps extended that were not representative of the airplane and identified some differences in pilot forces. The elevator hinge moment model and implementation of the control forces on the ICEFTD were identified as a driver in the pitch ups and control force issues, and will be an area for future work.

Ratvasky, Thomas P.↗