Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Industrial Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

High-Performance Integrated Window and Façade Solutions for California

The researchers developed a new generation of high-performance façade systems and supporting design and management tools to support industry in meeting California’s greenhouse gas reduction targets, reduce energy consumption, and enable an adaptable response to minimize real-time demands on the electricity grid. The project resulted in five outcomes: (1) The research team developed an R-5, 1-inch thick, triplepane, insulating glass unit with a novel low-conductance aluminum frame. This technology can help significantly reduce residential cooling and heating loads, particularly during the evening. (2) The team developed a prototype of a windowintegrated local ventilation and energy recovery device that provides clean, dry fresh air through the façade with minimal energy requirements. (3) A daylight-redirecting louver system was prototyped to redirect sunlight 15–40 feet from the window. Simulations estimated that lighting energy use could be reduced by 35–54 percent without glare. (4) A control system incorporating physics-based equations and a mathematical solver was prototyped and field tested to demonstrate feasibility. Simulations estimated that total electricity costs could be reduced by 9-28 percent on sunny summer days through adaptive control of operable shading and daylighting components and the thermostat compared to state-of-the-art automatic façade controls in commercial building perimeter zones. (5) Supporting models and tools needed by industry for technology R&D and market transformation activities were validated. Attaining California’s clean energy goals require making a fundamental shift from today’s ad-hoc assemblages of static components to turnkey, intelligent, responsive, integrated building façade systems. These systems offered significant reductions in energy use, peak demand, and operating cost in California.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Investigating Secondary Aerosol Processes in the Amazon through Molecular-level Characterization of Semi-Volatile Organics

In areas where biogenic emissions are oxidized in the presence of anthropogenic pollutants, it has become increasingly apparent that secondary organic aerosol (SOA) formation from biogenic volatile organic compounds (BVOCs) is substantially enhanced. The Amazon forest is the dominant source of BVOCs globally, and the forest is rapidly being converted to urban and agricultural uses. We participated in a collaborative field study located in the Amazon region around Manaus, Brazil, in 2014 (Green Ocean Amazon; GoAmazon). This study was designed to comprehensively examine how BVOC emissions (specifically, the most highly emitted non-methane hydrocarbon, isoprene, and lesser studied sesquiterpenes) and their interaction with anthropogenic pollution (i.e., nitrogen oxides, sulfur dioxide, and black carbon) alter the atmosphere’s oxidative capacity, influence secondary aerosol formation, atmospheric composition and, ultimately, affect the earth’s radiation balance and climate. We provide the first hourly, in-situ measurement of 30 sesquiterpenes and 4 diterpenes, roughly estimating that sesquiterpene oxidation contributes to 10-14% of ozone reactive loss by terpenes and at least 0.4–5% (median 1 %) of total submicron OA mass. However, this is likely a low-end estimate, as evidence for additional unaccounted sesquiterpenes and their oxidation products clearly exists. We also provide new perspectives on sulfate, NO x , and particle acidity influencing isoprene-derived SOA, comparing the central Amazon environment with Southeastern U.S.A. summer, representing clean to polluted conditions, respectively. We find that summed concentrations of isoprene-derived SOA tracers correlated with particulate sulfate spanning three orders of magnitude, suggesting that 1 μg m -3 reduction in sulfate corresponds with at least ~0.5 μg m -3 reduction in isoprene-derived SOA. We also find that SOA mass derived from isoprene oxidation in the presence of NO x is primarily comprised of aerosol sulfate bound with isoprene oxidation products (i.e. organosulfates), ~97% in the Amazon and ~55% in the Southeastern U.S. We infer under natural conditions in high isoprene emission regions, preindustrial aerosol sulfate was almost exclusively isoprene-derived organosulfates, which are traditionally thought as representative of anthropogenic influence. We further report the first field observations showing that particle acidity impacts the distribution of isoprene oxidation tracers in the gas and particle phases, providing physicochemical insight into isoprene SOA formation chemistry. Coupled with other co-located measurements by the DOE Atmospheric Radiation Measurement (ARM) team and collaborating PIs at our measurement site (called T3), on the G1 aircraft, and at additional field sites (T0, T1, T2) this data set has been used to understand emission, oxidation, and particle formation pathways at the molecular level, to elucidate how these pathways change when influenced by anthropogenic sources, and to evaluate their importance for the atmospheric budget of aerosols and the earth’s radiation balance on regional scales. Recommendations: Further constraint of the role of sesquiterpenes on ozone (O 3 ) reactivity and SOA formation is limited by the availability of authentic standards and synthesized compounds of sesquiterpenes and their oxidation products. Future research efforts should focus on making such standards available via custom synthesis to allow for accurate quantification and focused oxidation experiments that will fully elucidate the chemistry of these compounds in the atmosphere. Further, reductions in aerosol sulfate (via SO 2 emissions control) continues to be one of the most effective methods to reduce SOA formation from isoprene, but the concerted role of ammonia (NH 3 ) gas emissions from (agricultural) industry and other sources requires more investigation to better understand the role of aerosol acidity in SOA formation and potential controls. As GoAmazon particles can be more acidic compared to areas with greater anthropogenic NH 3 emissions, this promotes relatively greater organosulfate (OS) formation from isoprene even in the presence of NO x . Because OS and inorganic sulfate differ in water uptake properties, this implies preindustrial aerosol sulfate (albeit less abundant) may have been less reflective than current earth system models assume. Further research should investigate the radiative impacts of organic vs inorganic sulfate in aerosols to improve model representation. Finally, future work (currently underway) should include constraint of the contributions of monoterpene (C 10 H 16 ) BVOCs and biomass burning VOCs as precursors to SOA formation in the region as well as their impacts on radiative forcing in the climate system.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

A Generic and Multifunctional Electromagnetic Transient Model for Grid-Following Inverters

This paper presents a generic and multifunctional electromagnetic transient (EMT) dynamic model of grid-following (GFL) inverter-based resources (IBRs) using the PSCAD software platform. The features of the model include flexibility in selecting various types and combinations of DC sources covering photovoltaic modules, battery modules, and ideal DC-source modules as well as flexibility in selecting either switching or averaged models of the inverter. This model also covers exhaustive lists of controller algorithm, including open-loop/closed-loop PQ dispatch control, DC voltage and AC terminal voltage control, and conventional current control designed in the dq-domain, the ..alpha....beta.. -domain, and the positive-/negative-sequence domain. Moreover, this model is equipped with flexibility in selecting various types of current-limiting schemes, including saturation-based and latching-based current limiters, and anti-windup protection. Also, the EMT model is agnostic to the MVA rating and is suitable for interfacing transmission systems by complying with IEEE Std. 2800. The generality in the power circuits and the multifunctional options in the operation and control of the developed EMT model make it suitable for both academia and industry to study various power system aspects, including, but not limited to, the fault behavior of GFL IBRs, the impacts on the protection system, and the transient stability of a system interfaced with large numbers of GFL IBRs.

integrated circuit modeling↗
DOE OSTI2025

Mitigation for roof alterations to building 06-cp-65 at the area 6 control point, nevada national security site, nye county, nevada

Building 06-CP-65 has been determined to be a contributing element to the Area 6 Control Point Historic District (O’Neill et al. 2021; Reed 2022). It contributes to the significance of the historic district under Criterion A as one of the principal buildings that supported timing and firing operations for nuclear testing on the NNSS from 1966 to 1992. As such, the building served as a major warehouse with office space within the district. It was used by both REECo, a long-time general contractor at the NNSS, as well as EG&G, which provided technical support to the national laboratories and the DOD. The building served as an important staging area and electrical power supply point for the NNSS diagnostic trailer fleet and its unique location immediately along Mercury Highway allowed easy accessibility to the forward areas of the NNSS. The building also contributes to the historic district under Criterion C as it is one of the large, unadorned, precast concrete buildings at the Control Point. These types of buildings were the prominent elements of the compound that convey the district’s overall utilitarian, military-industrial character. Building 06-CP-65 retains all aspects of integrity to a high degree and easily conveys its significance as a warehouse that supported Control Point operations. Building 06-CP-65 is not recommended eligible for listing in the NRHP as an individual resource. While it served an important support function as part of the Control Point Historic District, an archival and literature review did not reveal information linking it to any specific test, series of tests, programs, or for any specific role on the NNSS other than as a warehouse (Criterion A). It has no direct association with any important individual (Criterion B). It also is not architecturally significant in its own right beyond reflecting the overall aesthetic of the Control Point Historic District (Criterion C), and it does not have potential to yield information important to the history of nuclear testing beyond what can be learned from historic texts, drawings, and other documents (Criterion D).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

A general synthesis of single atom catalysts with controllable atomic and mesoporous structures

The control of single metal atomic sites has been extensively studied in the field of single atom catalysts. By contrast, the precise control of the mesoporous structure in the matrix material, which directly correlates with mass diffusions and may play a dominant role in delivering industrially relevant reaction rates, has been overlooked. In this work, we report a general method for the synthesis of a single atom catalyst with control of the atomic structure of the single atomic site as well as the mesoporous structure of the carbon support for optimized catalytic performance. Various combinations of metal centres (Ni, Co, Mn, Zn, Cu, Sc and Fe) and mass diffusion channels in two dimensions and three dimensions were achieved. Using CO 2 reduction to CO as an example, our Ni single atom catalyst with three-dimensional diffusion channels delivered a practical current of 350 mA cm –2 while maintaining a 93% CO Faradaic efficiency, representing a sixfold improvement in turnover frequency compared to two-dimensional counterparts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Demonstration of Wake Steering Through Yaw Control in a Wind Plant Field Experiment: Cooperative Research and Development Final Report, CRADA Number CRD-16-00629

Over the last few decades, wind energy has evolved into a large international industry involving major players in the manufacturing, construction, and utility sectors. Coinciding with the industry’s growth, significant innovation in the technology has resulted in larger turbines with lower associated costs of energy and more complex designs in all subsystems. However, as the deployment of the technology has grown and its role within the electricity sector become more prominent, so have the expectations of the technology in terms of performance, reliability, and cost. The industry currently partitions its efforts into separate paths for turbine design, plant design and development, finance, grid interaction and operation, mitigation of adverse community and environmental impacts, and other areas. One prominent area where this partition is evident is in wind turbine control. Traditionally, each wind turbine in a wind plant has been controlled separately – via its own internal controller using only its own sensors. However, wind turbines in a plant interact with each other through the plant-level fluid dynamics. Wake losses (due to upstream turbines extracting energy from the winds and “waking” downstream turbines) can be up to 10% or even 20% of the gross energy production (if each turbine experienced the free stream wind inflow to the plant). A series of studies and experiments have demonstrated that there is potential for improving energy output at existing plants through plant control methods which seek to optimize total wind plant energy production over the current “greedy” approach where each turbine maximizes its own production. Wake steering induced by yaw offsets (turning the turbine to be out of the plane perpendicular to wind inflow) for upstream turbines has shown significant promise in simulations and wind tunnel experiments. In simulation studies, annual energy production has been shown to increase by 2% or more depending on the particular aspects of the wind plant (turbine spacing, meteorological conditions, etc). This project seeks to demonstrate the potential of plant-level controls via wake steering at a commercial wind plant. This is an important step towards commercialization and industry adoption of this plant-level modeling and analysis capability.

17 WIND ENERGY↗
DOE OSTI2022

Multi‐objective optimization for cost‐efficient and resilient machining under tool wear

Abstract With the onset and rapid growth of smart manufacturing, there is a constant increase in the demand for automation technologies to enhance productivity while providing uninterrupted, cost‐efficient, and resilient machining. Traditional manufacturing systems, however, suffer from several losses due to machine faults and degradation. Specifically, tool wear directly impacts the precision and quality of the milled parts, which causes an increase in the scrap production. Hence, more attempts are required to meet the desired quota of successful parts, which in turn results in wasted material, longer delays, further tool degradation, and higher energy, machining, and labor costs. As such, this paper develops a multi‐objective optimization framework to generate the optimal control set points (e.g., feed rate and width of cut) that minimize the total cost of machining operations resulting from multiple contradictory cost functions (e.g., material, energy, tardiness, machining, labor, and tool) in the presence of tool wear. Notably, we estimate the total expected cost in dollars, which provides automatic and intuitive weighting in this multi‐objective formulation. The optimization framework is tested on a high‐fidelity face milling model that has been validated on real data from industry. Results show significant dollar savings of up to as compared to the default control scheme.

Wilson, James P.↗
DOE OSTI2023

Beneficial Integration of Energy Storage and Load Management with Photovoltaic (PV)

In recent years, a number of industry activities have aimed at addressing the integration challenges posed by the variability and uncertainty of higher penetration of renewable generation sources, like solar photovoltaic (PV) – one of the key objectives of the Sustainable and Holistic Integration of Energy Storage and Solar PV (SHINES) program launched by the U.S. Department of Energy's Office of Energy Efficiency and Renewable Energy (EERE). This EPRI led Beneficial Integration of Energy Storge, and Load Management with PV project aimed to design, develop, and demonstrate end-to-end distributed energy resource (DER) integration solution to build on these activities. EPRI led project team designed and implemented a local controller that uses model predictive control (MPC) algorithm to optimally manage DERs on site by planning for a receding horizon while executing the control settings for the first step of its plan. The team has also developed a system controller to interface with the local controller to demonstrate the hierarchical control and how it can leverage DER capabilities to address challenges like over voltage and thermal limit violations which typically limits the DER hosting capacity of distribution feeders. Team has demonstrated how the local controller with optimization algorithm can effectively manage controllable loads like HVAC, water heater, and pool pumps to allow for greater integration of PV with relatively smaller energy storage system requirements. Optimal utilization of the load control can also reduce the depth of discharge of batteries to meet grid export/import limit from behind-the-meter (BTM) DERs. Proper utilization of DER capabilities via local control intelligence, like the one developed and demonstrated in this project can help the industry to address integration challenges of higher penetration of solar PV in economically efficient manner. This can help to accelerate deployment of clean renewable energy systems at lower societal cost.

14 SOLAR ENERGY↗
DOE OSTI2022

Control of Structural Hydrophobicity and Cation Solvation on Interlayer Water Transport during Clay Dehydration

Swelling clay hydration/dehydration is important to many environmental and industrial processes. Experimental studies usually probe equilibrium hydration states in an averaged manner and thus cannot capture the fast water transport and structural change in interlayers during hydration/dehydration. Using molecular simulations and thermogravimetric analyses, we observe a two-stage dehydration process. The first stage is controlled by evaporation at the edges: water molecules near hydrophobic sites and the first few water molecules of the hydration shell of cations move fast to particle edges for evaporation. The second stage is controlled by slow desorption of the last 1–2 water molecules from the cations and slow transport through the interlayers. The two-stage dehydration is strongly coupled with interlayer collapse and the coordination number changes of cations, all of which depend on layer charge distribution. Furthermore, this mechanistic interpretation of clay dehydration can be key to the coupled chemomechanical behavior in natural/engineered barriers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Solid-State Mixed-Potential Electrochemical Sensors for Natural Gas Leak Detection and Quality Control (Final Technical Report)

Mitigation of methane emissions are a critical factor to limiting the impact of the natural gas industry on global climate change. Throughout the period of 2020-2024, the University of New Mexico and its commercialization partner and subcontractor, SensorComm Technologies, Inc. (SCT), have worked together to develop a low-cost Artificial Intelligence (AI)-driven Internet of Things (IoT)-based multi-gas sensor platform for methane emissions detection. In the final year of the project, we extended this work to include hydrogen detection in support of a transition to a hydrogen economy where hydrogen could be transported through existing natural gas infrastructure. Mixed potential electrochemical sensors were first prototyped by ceramic additive manufacturing and then transitioned to conventional ceramic manufacturing tape casting and screen-printing technologies in preparation for mass production. Demonstrated limits of detection of 5 ppm of methane in natural gas and 1 ppm of hydrogen were measured. These limits of detection are among the lowest of solid-state electrochemical sensors that have been reported in the literature or available in the industry. Machine learning algorithms were developed to identify natural gas mixtures with > 98% accuracy level and quantify methane concentrations at 97% accuracy. The presence of hydrogen could also be identified, and its concentration quantified at these accuracy levels. These algorithms were optimized for running on portable computing hardware which enabled > 1 Hz processing rates. A portable packaged IoT system was integrated with the electrochemical sensor in collaboration with SCT. The package consists of readout electronics with < 1 mV resolution, sensor temperature control, and data transmission over cellular wireless and/or Wi-Fi networks. Field testing was performed in two rounds at Colorado State University’s Methane Emissions Technology Evaluation Center (CSU METEC). The first round of testing demonstrated successful measurements of methane from an underground natural gas leak of 20 standard liters per minute (SLPM), which agreed with previously published literature using more sophisticated and expensive analytical equipment. The second round of testing showed that an above ground leak of 2 SLPM of hydrogen could be detected at 32 ft. This project has resulted in six published peer reviewed journal articles, over ten presentations at professional conferences, and one full patent application filed in 2023. Future work on this project includes increased sensitivity, higher production yields, and applications in the hydrogen safety and flare emissions monitoring spaces.

03 NATURAL GAS↗
DOE OSTI2023

Effect of bimetallic modification on blast furnace slag and its application in low‐temperature selective catalytic reduction

Abstract Objective In order to control NO x in low‐temperature flue gases emitted from non‐power industries and to reduce the preparation cost of denitration catalysts, this study uses inexpensive blast furnace slag as raw material to prepare denitration catalysts. Methods After cooling, drying and grinding, the blast furnace slag becomes a powder with considerable fineness and meets the requirements of activity index, which is called GGBS (ground granulated blast furnace slag). Using GGBS as denitration catalyst carrier, the active components M (M = Fe, Co, Ni, Cu and Ce) are loaded on Mn‐based GGBS catalyst using an impregnation method. Conclusions The effect of different active components on the denitration performance and sulfur resistance of Mn‐based GGBS catalysts is investigated. The results show that the Mn‐Ce/GGBS catalyst has better denitration performance and sulfur resistance. The Mn‐Ce/GGBS catalyst has a significant denitration performance when load ratio is 2:1. The active component Ce improves the denitration performance of the catalyst, reduces sulfur poisoning and extends the life of the catalyst. The SO 2 in the flue gas increases the acid sites on the catalyst surface and improves catalyst activity. The larger the ratios of Mn 4+ /Mn 3+ , Ce 4+ /Ce 3+ and O α /O β , the stronger the catalyst activity and the better the denitration performance. © 2022 Society of Chemical Industry (SCI).

Zhang, Lei↗
DOE OSTI2024

Effect of Iron Contamination and Polysilicon Gettering on the Performance of Polysilicon‐Based Passivating Contact Solar Cells

Over the past decade, silicon solar cells with carrier-selective passivating contacts based on polysilicon capping an ultra-thin silicon oxide (commonly known as TOPCon or POLO) have demonstrated promising efficiency potentials and are regarded as an evolutionary upgrade to the PERC (passivated emitter and rear contact) cells in manufacturing. The polysilicon-based passivating contacts also exhibit excellent gettering effects that relax the wafer and cleanroom requirements to some extent. Here, in this work, we experimentally explore the impact of bulk iron contamination and polysilicon gettering on the passivation quality of the polysilicon/oxide structure and the resulting solar cells performance. Results show that both n- and p-type polysilicon/oxide passivating contacts are not affected by iron gettering, demonstrating robust and stable passivation quality. However, for a very high bulk iron contamination (1 × 10 13 cm −3 ), the accumulated iron in the p-type lightly boron-doped emitter in crystalline silicon would degrade the emitter saturation current density. This can cause a reduction in both open-circuit voltage and short-circuit current. Meanwhile, this very high iron content (1 × 10 13 cm −3 ) can further degrade the fill factor and temperature coefficient of the cells. On the other hand, for an initial iron content of 2 × 10 12 cm −3 , which should be well above the iron level in the current industrial Czochralski silicon wafers, the resulting cells demonstrate similar performance as the control group with no intentional iron contamination. This work brings attention to both the benefits of polysilicon gettering effects as well as the potential degradation due to the accumulation of metal impurities in the p-type emitter region.

14 SOLAR ENERGY↗
DOE OSTI2023

Designing Low Tortuosity Electrodes through Pattern Optimization for Fast-Charging

The development of fast-charging technologies is crucial for expediting the progress and promotion of electric vehicles. In addition to innovative material exploration, reduction in the tortuosity of electrodes is a favored strategy to enhance the fast-charging capability of lithium-ion batteries by optimizing the ion-transfer kinetics. To realize the industrialization of low-tortuosity electrodes, a facile, cost-effective, highly controlled, and high-output continuous additive manufacturing roll-to-roll screen printing technology is proposed to render customized vertical channels within electrodes. Extremely precise vertical channels are fabricated by applying the as-developed inks, using LiNi 0.6 Mn 0.2 Co 0.2 O 2 as the cathode material. Additionally, the relationship between the electrochemical properties and architecture of the channels, including the pattern, channel diameter, and edge distance between channels, is revealed. The optimized screen-printed electrode exhibited a seven-fold higher charge capacity (72 mAh g -1 ) at a current rate of 6 C and superior stability compared with that of the conventional bar-coated electrode (10 mAh g -1 , 6 C) at a mass loading of 10 mg cm -2 . Finally, this roll-to-roll additive manufacturing can potentially be applied to various active materials printing to reduce electrode tortuosity and enable fast charging in battery manufacturing.

42 ENGINEERING↗
DOE OSTI2026

A Systems-Level Approach to Address Risks and Ethics in Artificial Intelligence Systems

Artificial intelligence (AI) is rapidly changing the world, from completely controlling routine or mundane tasks like text and image generation, to powering advanced algorithms that control critical systems. The recent advances in generative AI quickly overwhelmed multiple industries from education to finance as first adopters rushed (and continue to rush) to take advantage of the technology. The expanding AI ecosystem presents novel risks and ethical challenges that must be handled to ensure that technology is leveraged fairly and ethically. There are intertwined risks and ethical challenges stemming from the stochastic nature of AI (i.e., intrinsic risks), as well as from specific applications (i.e., extrinsic risks). Appropriately regulating AI requires a systems-approach to develop an integrated solution to these dependent challenges. Thus far, however, questions of risk, ethics and regulation appear to occupy separate spaces. This paper reviews the risks and ethical implications of AI and proposes a system-level approach to integrating ethics and regulation for the nascent industry.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Evolution of AISI 304L stainless steel part properties due to powder recycling in laser powder-bed fusion

Selective laser melting (SLM) is a powder-bed fusion process in Additive Manufacturing (AM) that uses a laser beam to selectively fuse layers of powder into near net-shape components with little porosity. However, inconsistencies in the part properties due to the presence of defects in as-built components has hindered the widespread adoption of SLM for industrial applications forcing researchers to study the sources of variation for quality control purposes. A critical area suspected of creating variation in the part properties is the feedstock, where batch-to-batch differences as well as changes in the powder properties with reuse have the potential to affect performance. During processing, laser spatter and condensate eject from the melt pool and deposit into the powder-bed surrounding the parts. These particulates, more commonly known as ejecta, differ morphologically and chemically from the virgin powder compromising its reusability. In this study, 304L stainless steel powder was recycled for a total of 5 times through a systematic approach aimed at accelerating powder degradation to reveal the influence on both the tensile and impact toughness properties. Through analysis of variance (ANOVA), it was found that tensile properties did not change with reuse, while the impact toughness showed a steady decline illustrating the differences in static and dynamic part properties due to powder recycling.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Methane foam performance evaluation in water-wet unconsolidated porous media: A systematic experimental investigation at elevated pressure and temperature conditions

In the petroleum industry, enhanced oil recovery (EOR) techniques employ foam extensively to establish conformance control in heterogeneous and fractured reservoirs in order to increase the sweep efficiency. In such applications, foam performance evaluation under complex subsurface conditions is pivotal for the effective and optimized deployment of foam treatment. However, there is a scarcity of hydrocarbon gas foam generation and evaluation studies that examine the relationships between foam performance and the critical foam parameters at high-pressure and high-temperature conditions. Here, this study aims at methodically investigating the effects of several foam parameters on methane foam performance in water-wet proppant packs under harsh operating conditions. This is in relation to the technical needs of hydrocarbon foam injection into hydraulically-induced, propped fractures in unconventional oil reservoirs. To this end, a state-of-the-art experimental foam generation apparatus was designed, fabricated, and commissioned. We performed a large number of foam flow experiments on proppant packs using methane gas and different foaming agents at 3500 psi and 115°C. Anionic and amphoteric surfactants were employed to probe the effect of their ionic nature on foam performance. Foam performance sensitivities to various foam generation parameters and operating conditions, such as surfactant concentration, gas fraction, total injection rate, operating pressure, salinity, and proppant pack length were investigated. To this end, steady-state pressure drops across the proppant packs during foam generation and foam's apparent viscosity were measured to quantify the foam performance of surfactants. The results were then analyzed to determine optimum values of the foam parameters and the interplay between these parameters are discussed here. The systematic results achieved from this work are in agreement with the trends available in the literature and provide new insights into complexities of in situ foam generation in water-wet, unconsolidated porous media at extreme reservoir conditions.

03 NATURAL GAS↗
DOE OSTI2025

Cold air quench control of local crystallization environment in fully air-processed carbon-based perovskite solar cells

Carbon-based perovskite solar cells (C-PSCs) present a low-cost route to efficient photovoltaic technology. Gas quenching is an essential process commonly used for solvent extraction in scalable module fabrication using solution processes, but film quality remains highly sensitive to the localized environmental processing temperature, especially during intermediate phase transitions before perovskite film high temperature annealing. In this study, we introduce a cold air quench strategy to precisely control the local crystallization temperature that simultaneously promotes uniform crystallization and facilitates strain relaxation in fully air-processed C-PSCs. It is found that implementing dry air at 10 °C as the quenching gas yields a champion power conversion efficiency (PCE) of 20.52 %, with preferential (110) orientation and reduced, homogenized in-plane strain. This newly developed technique of a cost-effective low temperature air quenching process also enhances carrier lifetime, reduces interface recombination, and improves charge extraction. Furthermore, this work presents cold air quenching as a scalable, economic method to control perovskite crystallization and strain in C-PSC fabrication, advancing the industrial viability of high-performance perovskite modules.

14 SOLAR ENERGY↗
DOE OSTI2023

Exploring the formation of gold/silver nanoalloys with gas-phase synthesis and machine-learning assisted simulations

While nanoalloys are of paramount scientific and practical interest, the main processes leading to their formation are still poorly understood. Key structural features in the alloy systems, including the crystal phase, chemical ordering, and morphology, are challenging to control at the nanoscale, making it difficult to extend their use to industrial applications. Here, in this contribution, we focus on the gold/silver system that has two of the most prevalent noble metals and combine experiments with simulations to uncover the formation mechanisms at the atomic level. Nanoparticles were produced using a state-of-the-art inert-gas aggregation source and analyzed using transmission electron microscopy and energy-dispersive X-ray spectroscopy. Machine-learning-assisted molecular dynamics simulations were employed to model the crystallization process from liquid droplets to nanocrystals. Our study finds a preponderance of nanoparticles with five-fold symmetric morphology, including icosahedra and decahedra which is consistent with previous results on mono-metallic nanoparticles. However, we observed that gold atoms, rather than silver atoms, segregate at the surface of the obtained nanoparticles for all the considered alloy compositions. These segregation tendencies are in contrast to previous studies and have consequences on the crystallization dynamics and the subsequent crystal ordering. We finally showed that the underpinning of this surprising segregation dynamics is due to charge transfer and electrostatic interactions rather than surface energy considerations.

36 MATERIALS SCIENCE↗