Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Impact cratering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Durability evaluation of photovoltaic blanket materials exposed on LDEF tray S1003

Several candidate protective coatings on Kapton and uncoated Kapton were exposed to the low Earth orbital (LEO) environment on the Long Duration Exposure Facility (LDEF) to determine if the coatings could be used to protect polymeric substrates from degradation in the LEO environment. The coatings that were evaluated were 700 A of aluminum oxide, 650 A of silicon dioxide, and 650 A of a 4 percent polytetrafluoroethylene-96 percent silicon dioxide mixed coating. All of the coatings evaluated were ion beam sputter deposited. These materials were exposed to a very low atomic oxygen fluence (4.8 x 10 exp 19 atoms/sq. cm) as a result of the experiment tray being located 98 degrees from the ram direction. As a result of the low atomic oxygen fluence, determination of a change in mass was not possible for any of the samples including the uncoated Kapton. There was no evidence of spalling of any of the coatings after the approximately 33,600 thermal cycles recorded for LDEF. The surface of the uncoated Kapton, however, did show evidence of grazing incidence texturing. There was a 7-8 percent increase in solar absorptance for the silicon dioxide and aluminum oxide coated Kapton and only a 4 percent increase for the mixed coating. It appears that the addition of a small amount of fluoropolymer may reduce the magnitude of absorptance increase due to environmental exposure. Thermal emittance did not change significantly for any of the exposed samples. Scanning electron microscopy revealed few micrometeoroid or debris impacts, but the impact sites found indicated that the extent of damage or cracking of the coating around the defect site did not extend beyond a factor of three of the impact crater diameter. This limiting of impact damage is of great significance for the durability of thin film coatings used for protection against the LEO environment.

Sharon K Rutledge↗
NASA NTRS1994

The surface and interior of Phobos

The impact crater Stickney dominates one hemisphere of the Martian moon Phobos; its diameter (11 km) is about half the size of the body (19 x 22 x 27 km). Besides demarking a threshold between cratering and catastrophic disruption, this impact reveals a great deal about the target's interior. Because Phobos has an unusually low density yet exhibits no direct evidence for volatiles such as water ice, it has been supposed that it sequesters volatiles in the deep interior, or that it is made of some exotic substance, or that it is a loosely-aggregated rubble pile. The network of fracture grooves created by the Stickney impact constrain which, if any, of these models accord with observation.

Asphaug, E.↗
NASA NTRS1994

Scaling craters in carbonates: Electron paramagnetic resonance analysis of shock damage

Carbonate samples from the 8.9-Mt nuclear (near-surface explosion) crater, OAK, and a terrestrial impact crater, Meteor Crater, were analyzed for shock damage using electron paramagnetic resonance (EPR). Samples from below the OAK apparent crater floor were obtained from six boreholes, as well as ejecta recovered from the crater floor. The degree of shock damage in the carbonate material was assessed by comparing the sample spectra to the spectra of Solenhofen and Kaibab limestone, which had been skocked to known pressures. Analysis of the OAK Crater borehole samples has identified a thin zone of allocthonous highly shocked (10-13 GPa) carbonate material underneath the apparent crater floor. This approx. 5- to 15-m-thick zone occurs at a maximum depth of approx. 125 m below current seafloor at the borehole, sited at the initial position of the OAK explosive, and decreases in depth towards the apparent crater edge. Because this zone of allocthonous shocked rock delineates deformed rock below, and a breccia of mobilized sand and collapse debris above, it appears to outline the transient crater. The transient crater volume inferred in this way is found to by 3.2 +/- 0.2 times 10(exp 6)cu m, which is in good agreement with a volume of 5.3 times 10(exp 6)cu m inferred from gravity scaling of laboratory experiments. A layer of highly shocked material is also found near the surface outside the crater. The latter material could represent a fallout ejecta layer. The ejecta boulders recovered from the present crater floor experienced a range of shock pressures from approx. 0 to 15 GPa with the more heavily shocked samples all occurring between radii of 360 and approx. 600 m. Moreover, the fossil content, lithology and Sr isotopic composition all demonstrate that the initial position of the bulk of the heavily shocked rock ejecta sampled was originally near surface rock at initial depths in the 32 to 45-m depth (below sea level) range. The EPR technique is also sensitive to prehistoric shock damage. This is demonstrated by our study of shocked Kaibab limestone from the 49,000-year-old Meteor (Barringer) Crater Arizona.

Polanskey, Carol A.↗
NASA NTRS2019

An Astronaut's Risk of Experiencing a Critical Impact from Lunar Ejecta During Lunar EVA

The Moon is under constant bombardment by meteoroids. When the meteoroid is large, the impact craters the surface, launching crater ejecta far from the impact potentially threatening astronauts on the lunar surface. In the early 1960’s, the ejecta impact flux was thought no more than the sporadic meteoroid flux but with speeds one to two orders of magnitude smaller. However, the Lunar Module designers realized by 1965 that meteoroid bumpers do not perform well at the smaller ejecta impact speeds. Their estimates of the Lunar Module risk of penetration by ejecta were 25 to 50% of the total risk. This was in spite of the exposure time to ejecta being only a third of that to sporadic meteoroids. The standard committee based the 1969 NASA SP-8013 lunar ejecta environment on Zook’s 1967 flux analysis and Gault, Shoemaker and Moore’s 1963 test data for impacts into solid basalt targets. However, Zook noted in his 1967 analysis, that if the lunar surface was composed of soil, that the ejected soil particles would be smaller than ejected basalt fragments and that the ejection speeds would be smaller. Both effects contribute to reducing the risk of a critical failure due to lunar ejecta. The authors revised Zook’s analysis to incorporate soil particle size distributions developed from analysis of Apollo lunar soil samples and ejected mass as a function of ejecta speed developed from coupling parameter analyses of soil impact-test data. The authors estimated EVA risk by assuming failure occurs at a critical impact energy. At these impact speeds, this might be true for suit hard and soft goods. However, these speeds are small enough that there may be significant strength effects that require new test data to modify the hypervelocity critical energy failure criterion. With these caveats, Christiansen, Cour-Palais and Freisen list the critical energy of the ISS EMU hard upper torso as 44 J and the helmet and visor as 71 J at hypervelocity. The authors then assumed that the lunar EVA suit fails at 50 J critical energy. This results in a 1,700,000 years mean time to failure using the results of this analysis and a 3,800 years mean time to failure using NASA SP-8013.

Bjorkman, Michael D.↗
NASA NTRS2011

Global Distribution of Small Rayed Craters on Mars: Sequences of Ejecta Retention

Small rayed impact craters (SRC), whose diameter (D) is less than1 km, should be distributed spatially and temporally random across Mars. Ejecta retention, the capacity of and time period impact excavated material remains in place around a crater, can serve as a proxy to understand global resurfacing rates and recent surficial processes. Ejecta retention depends on two factors: formation, where the target material is more conducive to creating ejecta rays, and retention, the erosion/deposition rate where ejecta are emplaced. This research aims to quantify the distribution of SRC on Mars, as well as develop a classification scheme for ejecta retention with correlations to known processes. Our ultimate goal is to better understand the retention environment over the "lifespan" of the rayed ejecta.

spatial distribution↗
NASA NTRS2015

Stratigraphy of the Caloris Basin, Mercury: Implications for Volcanic History and Basin Impact Melt

Caloris basin, Mercury's youngest large impact basin, is filled by volcanic plains that are spectrally distinct from surrounding material. Post-plains impact craters of a variety of sizes populate the basin interior, and the spectra of the material they have excavated enable the thickness of the volcanic fill to be estimated and reveal the nature of the subsurface. The thickness of the interior volcanic plains is consistently at least 2.5 km, reaching 3.5 km in places, with thinner fill toward the edge of the basin. No systematic variations in fill thickness are observed with long-wavelength topography or azimuth. The lack of correlation between plains thickness and variations in elevation at large horizontal scales within the basin indicates that plains emplacement must have predated most, if not all, of the changes in long-wavelength topography that affected the basin. There are no embayed or unambiguously buried (ghost) craters with diameters greater than 10 km in the Caloris interior plains. The absence of such ghost craters indicates that one or more of the following scenarios must hold: the plains are sufficiently thick to have buried all evidence of craters that formed between the Caloris impact event and the emplacement of the plains; the plains were emplaced soon after basin formation; or the complex tectonic deformation of the basin interior has disguised wrinkle-ridge rings localized by buried craters. That low-reflectance material (LRM) was exposed by every impact that penetrated through the surface volcanic plains provides a means to explore near-surface stratigraphy. If all occurrences of LRM are derived from a single layer, the subsurface LRM deposit is at least 7.5-8.5 km thick and its top likely once made up the Caloris basin floor. The Caloris-forming impact would have generated a layer of impact melt 3-15 km thick; such a layer could account for the entire thickness of LRM. This material would have been derived from a combination of lower crust and upper mantle.

Cratering↗
NASA NTRS1977

Pre-impact conditions and cratering processes at the Flynn Creek crater, Tennessee

A description is presented of a preliminary outline for the cratering processes at Flynn Creek, Tennessee, a large, flat-floored, terrestrial impact crater with a central uplift. The initial preimpact conditions in terms of terrain, target media, and structure are defined, taking into account the possibility of impact into a shallow sea. A brief outline is provided of the generalized sequence of events from the time of entry of the impacting body into the atmosphere through the termination of late-stage cratering motions. The abbreviated sequence of cratering events is based upon a composite of recently assembled physical constraints, including new field data, experimental laboratory impact and field explosion trials, and theoretical numerical simulation studies.

Roddy, D. J.↗
NASA NTRS1976

Floor-fractured lunar craters

Observational data concerning floor-fractured craters on the lunar near and far sides are examined, including the morphologic classification of the craters, their spatial and size distributions, and their floor, peak, and rim elevations relative to the maria. Six morphologic classes and two subclasses are delineated on the basis of fracture pattern, crater floor depth, and floor type. These data are used to reconstruct a history of crater modification which accounts for the large differences in affected crater size and age, the small peak-rim elevation differences, remnant central peaks within mare-flooded craters and ringed plains, ridged and flat-topped rim profiles of heavily modified craters and ringed plains, as well as the absence of positive gravity anomalies in most floor-fractured craters and some large mare-filled craters. The results indicate that: (1) impact craters became centers of intrusions and volcanism generally related to periods of basin inundation by mare basalts; (2) some light-plains units in the highlands may be due to both impact ejecta and extrusions of light-colored lava or ash; (3) floor-fractured craters may have become important volcanic vents that contributed to the inundation of the lunar surface by mare basalts; and (4) the lunar highlands probably did not fully escape the epochs of mare flooding.

Schultz, P. H.↗
NASA NTRS1996

New Constraints on the Slate Islands Impact Structure, Ontario, Canada

The Slate Islands in northern Lake Superior represent the eroded remains of a complex impact crater, originally approximately 32 km in diameter. New field studies there reveal allogenic crater fill deposits along the eastern and northern portions of the islands indicating that this 500-800 Ma impact structure is not as heavily eroded as previously thought. Near the crater center, on the western side or Patterson Island, massive blocks of target rocks, enclosed within a matrix of fine-grained polymict breccia, record the extensive deformation associated with the central uplift. Shatter cones are a common structural feature on the islands and range from less than 3 cm to over 10 m in length. Although shatter cones are powerful tools for recognizing and analyzing eroded impact craters, their origin remains poorly constrained.

Sharpton, Virgil L.↗
DOE OSTI2021

Melting and Ejecta Produced by High Velocity Microparticle Impacts of Steel on Tin

At sufficiently high velocities, a microparticle impacting a metal substrate can cause ejection of material from the substrate and impact-induced melting, both of which can result in erosion. Here, we directly image the impact of individual hard steel microparticles on soft tin substrates, at controlled impact velocities in the range of ~100 to 1000 m/s. By using scanning electron and laser scanning confocal microscopy, we characterize the surface morphology, depth, and volume of each impact crater. We observe a gradual onset of impact-induced melting in the craters, as well as the production of increasing amounts of ejecta from the target metal. By comparing measurements of impact and rebound velocity to an elastic-plastic model, we observe that at a high enough impact velocity, melting and ejection begin to consume additional kinetic energy beyond that expected by plastic deformation of the target material alone. By calculating the excess energy dissipation using this elastic-plastic model, we show that although this divergent behavior is associated with the onset of melting, the majority of the ejected volume must be solid rather than liquid.

Mechanics↗
NASA NTRS2004

Migration of the Cratering Flow-Field Center with Implications for Scaling Oblique Impacts

Crater-scaling relationships are used to predict many cratering phenomena such as final crater diameter and ejection speeds. Such nondimensional relationships are commonly determined from experimental impact and explosion data. Almost without exception, these crater-scaling relationships have used data from vertical impacts (90 deg. to the horizontal). The majority of impact craters, however, form by impacts at angles near 45 deg. to the horizontal. While even low impact angles result in relatively circular craters in sand targets, the effects of impact angle have been shown to extend well into the excavation stage of crater growth. Thus, the scaling of oblique impacts needs to be investigated more thoroughly in order to quantify fully how impact angle affects ejection speed and angle. In this study, ejection parameters from vertical (90 deg.) and 30 deg. oblique impacts are measured using three-dimensional particle image velocimetry (3D PIV) at the NASA Ames Vertical Gun Range (AVGR). The primary goal is to determine the horizontal migration of the cratering flow-field center (FFC). The location of the FFC at the time of ejection controls the scaling of oblique impacts. For vertical impacts the FFC coincides with the impact point (IP) and the crater center (CC). Oblique impacts reflect a more complex, horizontally migrating flow-field. A single, stationary point-source model cannot be used accurately to describe the evolution of the ejection angles from oblique impacts. The ejection speeds for oblique impacts also do not follow standard scaling relationships. The migration of the FFC needs to be understood and incorporated into any revised scaling relationships.

Anderson, J. L. B.↗
NASA NTRS1994

The intact capture of hypervelocity dust particles using underdense foams

The impact of a hypervelocity projectile (greater than 3 km/s) is a process that subjects both the impactor and the impacted material to a large transient pressure distribution. The resultant stresses cause a large degree of fragmentation, melting, vaporization, and ionization (for normal densities). The pressure regime magnitude, however, is directly related to the density relationship between the projectile and target materials. As a consequence, a high-density impactor on a low-density target will experience the lowest level of damage. Historically, there have been three different approaches toward achieving the lowest possible target density. The first employs a projectile impinging on a foil or film of moderate density, but whose thickness is much less than the particle diameter. This results in the particle experiencing a pressure transient with both a short duration and a greatly reduced destructive effect. A succession of these films, spaced to allow nondestructive energy dissipation between impacts, will reduce the impactor's kinetic energy without allowing its internal energy to rise to the point where destruction of the projectile mass will occur. An added advantage to this method is that it yields the possibility of regions within the captured particle where a minimum of thermal modification has taken place. Polymer foams have been employed as the primary method of capturing particles with minimum degradation. The manufacture of extremely low bulk density materials is usually achieved by the introduction of voids into the material base. It must be noted, however, that a foam structure only has a true bulk density of the mixture at sizes much larger than the cell size, since for impact processes this is of paramount importance. The scale at which the bulk density must still be close to that of the mixture is approximately equal to the impactor. When this density criterion is met, shock pressures during impact are minimized, which in turn maximizes the probability of survival for the impacting particle. The primary objectives of the experiment are to (1) Examine the morphology of primary and secondary hypervelocity impact craters. Primary attention will be paid to craters caused by ejecta during hypervelocity impacts of different substrates. (2) Determine the size distribution of ejecta by means of witness plates and collect fragments of ejecta from craters by means of momentum-sensitive mcropore foam. (3) Assess the directionality of the flux by means of penetration-hole alignment of thin films placed above the cells. (4) Capture intact the particles that perforated the thin film and entered the cell. Capture media consisted of both previously flight-tested micropore foams and aerogel. The foams had different latent heats of fusion and, accordingly, will capture particles over a range of momenta. Aerogel was incorporated into the cells to determine the minimum diameter than can be captured intact.

Maag, Carl R.↗
NASA NTRS2020

Modification of Caloris ejecta blocks by long-lived mass-wasting: A volatile-driven process?

The Caloris basin is the largest well-preserved impact basin on Mercury. As such, Caloris ejecta afford us an opportunity to study material from Mercury's deep interior with remote sensing. We have made observations of the geomorphology, colour, distribution, and flank slopes of the circum-Caloris knobs. Our observations suggest that these circum-Caloris knobs are modified ejecta blocks from the Caloris impact. High-resolution MESSENGER images show that knobs are conical and relatively uncratered compared with the surrounding plains, which implies the knobs have undergone resurfacing. We have observed material that has sloughed off knobs superposing impact craters that demonstrably postdate the Caloris impact, which requires some knob modification to have been more recent. We have observed hollows, depressions in Mercury's surface generally believed to have been caused by volatile-loss, on and closely associated with several knobs, which indicates that many knobs contain volatile material and that knob modification could extend into Mercury's recent past. Our measurements show that knob flanks typically have slopes of ∼21°, which is steep for a mound of unconsolidated material that was originally emplaced ∼3.8 Ga. The conical shape of knobs, their steep slopes, the dearth of superposed craters on knobs, and knob superposition relationships with other landforms suggest that Caloris ejecta blocks of arbitrary original shape were modified into their present shapes by long-lived mass-wasting. Mass-wasting must have dominated over impact gardening, which would have produced domal morphologies only. We suggest that mass-wasting was probably driven by volatile-loss, in a manner analogous to terrestrial landforms called ‘molards’. If the circum-Caloris knobs are analogous to molards, then they represent a landform and a process hitherto undocumented on Mercury, with implications for the volatile content of the planet's interior. These knobs therefore are prime targets for BepiColombo, which could search for fresh failures and volatile exposures in the knobs.

Mercury; Caloris basin; impact ejecta; volatiles; ↗
NASA NTRS2000

Periodic Comet Showers, Mass Extinctions, and the Galaxy

Geologic data on mass extinctions of life and evidence of large impacts on the Earth are thus far consistent with a quasi-periodic modulation of the flux of Oort cloud comets. Impacts of large comets and asteroids are capable of causing mass extinction of species, and the records of large impact craters and mass show a correlation. Impacts and extinctions display periods in the range of approximately 31 +/- 5 m.y., depending on dating methods, published time scales, length of record, and number of events analyzed. Statistical studies show that observed differences in the formal periodicity of extinctions and craters are to be expected, taking into consideration problems in dating and the likelihood that both records would be mixtures of periodic and random events. These results could be explained by quasi-periodic showers of Oort Cloud comets with a similar cycle. The best candidate for a pacemaker for comet showers is the Sun's vertical oscillation through the plane of the Galaxy, with a half-period over the last 250 million years in the same range. We originally suggested that the probability of encounters with molecular clouds that could perturb the Oort comet cloud and cause comet showers is modulated by the Sun's vertical motion through the galactic disk. Tidal forces produced by the overall gravitational field of the Galaxy can also cause perturbations of cometary orbits. Since these forces vary with the changing position of the solar system in the Galaxy, they provide a mechanism for the periodic variation in the flux of Oort cloud comets into the inner solar system. The cycle time and degree of modulation depend critically on the mass distribution in the galactic disk. Additional information is contained in the original extended abstract.

Rampino, M. R.↗
NASA NTRS1978

Volcanism in the Noachis-Hellas region of Mars, 2

Mariner 9 and Viking Orbiter imagery has been examined to investigate volcanism in the Noachis-Hellas region of Mars. A wide variety of probable and possible volcanic features, including cinder cones, flood lavas, wrinkel ridges, cratered domes on the floors of impact craters, shield volcanoes, and possible stratovolcanoes has been observed. The flood lavas of ridged plains and broad, low shield volcanoes are indicative of very fluid lavas of ultrabasic or very basic basaltic composition. Evidence for relatively recent pyroclastic volcanism is present in numerous probable cinder cones and some isolated cratered mountains tentatively identified as stratovolcanoes. The volcanic complex and ridged plains at 68 deg S, 323 deg W appear to be relatively young. The occurrence of the five major volcanic centers of the Noachis-Hellas region at the intersections of ancient Hellas impact basin rings with a postulated northeast-trending fracture system suggests that large-scale volcanic activity may have begun soon after formation of the basin.

Peterson, J. E.↗
NASA NTRS1994

Evidence for a Meteoritic Component in Impact Melt Rock from the Chicxulub Structure

The Chicxulub structure in Yucatan, Mexico, has recently been recognized as a greater then 200-km-diameter multi-ring impact crater of K-T boundary age. Crystalline impact melt rocks and breccias from within the crater, which have compositions similar to those of normal continental crustal rocks and which show shock metamorphic effects, have been studied for trace element and Re-Os isotope compositions. Re-Os isotope systematics allow the sensitive and selective determination of an extraterrestrial component in impact-derived rocks. A melt rock sample shows elevated iridium concentrations, an osmium concentration of 25 ppb, and a low Os-187/Os-188 ratio of 0.113, which are incompatible with derivation from the continental crust. Even though the Os-187/Os-188 ratio is slightly lower than the range so far measured in meteorites, a mantle origin seems unlikely for mass balance reasons and because the cratering event is unlikely to have excavated mantle material. The data support the hypothesis of a heterogeneously distributed meteoritic component in the Chicxulub melt rock. A sample of impact glass from the Haitian K-T boundary at Beloc yielded about 0.1 ppb osmium and an Os-187/0s-188 ratio of 0.251, indicating the presence of a small meteoritic component in the impact ejecta as well.

Koeberl, Christian↗
NASA NTRS1974

Depth/diameter relations of fresh lunar craters - Revision from spacecraft data

The first systematic data from Apollo photogrammetry provide a high standard of accuracy for the depth/diameter relation of fresh lunar craters. Apollo depth-diameter results resemble results obtained by measuring shadows on Lunar Orbiter imagery. The depth-diameter distribution inflects at a crater diameter of 10 to 15 km. Lunar craters less than 15 km across are at least 50% deeper than older, telescopic data indicated, but larger craters are not much deeper. There is no marked depth-diameter difference between fresh upland and postmare craters. The new depth-diameter relation for small lunar craters resembles those of experimental and impact craters on earth.

Pike, R. J.↗
NASA NTRS1979

Lunar magnetic anomalies detected by the Apollo subsatellite magnetometers

Properties of lunar crustal magnetization thus far deduced from Apollo subsatellite magnetometer data are reviewed using two of the most accurate available magnetic anomaly maps, one covering a portion of the lunar near side and the other a part of the far side. The largest single anomaly found within the region of coverage on the near-side map correlates exactly with a conspicuous light-colored marking in western Oceanus Procellarum called Reiner Gamma. This feature is interpreted as an unusual deposit of ejecta from secondary craters of the large nearby primary impact crater Cavalerius. The mean altitude of the far-side anomaly gap is much higher than that of the near side map and the surface geology is more complex; individual anomaly sources have therefore not yet been identified. The mechanism of magnetization and the origin of the magnetizing field remain unresolved, but the uniformity with which the Reiner Gamma deposit is apparently magnetized, and the north-south depletion of magnetization intensity across a substantial portion of the far side, seem to require the existence of an ambient field, perhaps of global or larger extent.

Hood, L. L.↗