Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “High Temperature Reactor designs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Investigation of low NOx staged combustor concept in high-speed civil transport engines

Levels of exhaust emissions due to high temperatures in the main combustor of high-speed civil transport (HSCT) engines during supersonic cruise are predicted. These predictions are based on a new combustor design approach: a rich burn/quick quench/lean burn combustor. A two-stage stirred reactor model is used to calculate the combustion efficiency and exhaust emissions of this novel combustor. A propane-air chemical kinetics model is used to simulate the fuel-rich combustion of jet fuel. Predicted engine exhaust emissions are compared with available experimental test data. The effect of HSCT engine operating conditions on the levels of exhaust emissions is also presented. The work described in this paper is a part of the NASA Lewis Research Center High-Speed Civil Transport Low NO(x) Combustor program.

Nguyen, Hung Lee↗
DOE OSTI2021

Implementation of an Experimental Setup Based on the Three-Omega Method for Thermal Conductivity Measurements of Molten Salts

Molten salt reactors (MSRs) are one of the most promising next-generation nuclear reactor designs which use molten salts as the fuel and coolant. To design, model, predict, license, and operate MSRs, the behavior of the fuel and coolant must be understood as a function of temperature and irradiation, i.e., burnup. Of particular importance and complexity is the reliable and reproducible measurement of thermal conductivity of molten salts at high temperatures (> 500 °C). Thermal conductivity provides information on the rate at which heat passes through a specified material and is dependent on chemical composition. Currently, in the national laboratory complex, several methods for measuring thermal conductivity on molten salt systems are under development, however, to date, consistent data have not been produced. Typically, thermal conductivity measurements of high-temperature melts have been conducted by using the Transient Hot Wire (THW) method where thermal conductivity is determined by the change in temperature over time at a certain distance from a heating wire. Another time-dependent technique is the laser flash method, commonly used for solid samples. Laser flash requires prior measurements of density and heat capacity to calculate the thermal conductivity of the sample, introducing additional measurement errors. Steady state and time-dependent measurements such as THW and laser flash have errors from convection and ambient temperature fluctuations (heat radiation). In order to produce high fidelity thermal conductivity data, a measurement technique needs to be developed that will reduce the effect of convection at high temperatures by measuring in a very fast time window. In addition, to measure on actinide and irradiated salts the sample size should be small. Therefore, this project aims to develop a frequency-domain technique based on the three-omega (3?) method, previously proven to work on solids, nanofluids and low temperature solar salts (25 to 250 °C). If the 3?-device can be designed with materials that can withstand high temperatures (>500 °C) and can be configured to reduce errors due to convection, then it would prove to be a valuable technique for ensuring thermal conductivity on molten salt systems needed for MSR development. For this proposal, the 3? instrument will be designed, assembled, and tested on non-radioactive salts before being used on actinide bearing salts. In addition, a thermal model will be developed to determine the thermal conductivity of the sample from the measured thermal oscillation of the sensor. Because 3? is a direct method that requires a small volume of sample and works in a very fast time window, it will aid in suppressing the interference due to convection which is ideal when working with high temperature liquid samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Enhanced Design of Radiation Tolerant High-Temperature Structural Health Monitoring Sensors

Acoustic emission sensors are vital in the nuclear industry for real-time structural health monitoring and early detection of material degradation. By capturing high-frequency stress waves emitted from defects like cracks, corrosion, or fatigue, acoustic emission sensors enable non-invasive monitoring of critical components such as reactor vessels, piping, and containment structures. This technology supports predictive maintenance, enhances safety, and ensures regulatory compliance by providing early warnings of potential failures. It is also instrumental in research, particularly in material testing reactors, where it is used to monitor the behavior of fuels and materials under irradiation, by allowing the detection of cracking or other acoustic signals in real time. This enables the evaluation of performance and accident behavior of advanced fuel concepts.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
DOE OSTI2024

A First-Principles Study of the Structural and Thermo-Mechanical Properties of Tungsten-Based Plasma-Facing Materials

Tungsten (W) and tungsten alloys are being considered as leading candidates for structural and functional materials in future fusion energy devices. The most attractive properties of tungsten for the design of magnetic and inertial fusion energy reactors are its high melting point, high thermal conductivity, low sputtering yield, and low long-term disposal radioactive footprint. Despite these relevant features, there is a lack of understanding of how the structural and mechanical properties of W-based alloys are affected by the temperature in fusion power plants. In this work, we present a study on the thermo-mechanical properties of five W-based plasma-facing materials. First-principles density functional theory (DFT) calculations are combined with the quasi-harmonic approximation (QHA) theory to investigate the electronic, structural, mechanical, and thermal properties of these W-based alloys as a function of temperature. The coefficient of thermal expansion, temperature-dependent elastic constants, and several elastic parameters, including bulk and Young’s modulus, are calculated. Our work advances the understanding of the structural and thermo-mechanical behavior of W-based materials, thus providing insights into the design and selection of candidate plasma-facing materials in fusion energy devices.

42 ENGINEERING↗
DOE OSTI2024

Under the microscope: Reduced activation ferritic martensitic steel Eurofer-97 following ion-Irradiation and high-temperature high-pressure water exposure

Here, this study is designed to characterise the microstructural behaviour of Eurofer-97 steel under ion irradiation and subsequent exposure to high-temperature high-pressure (HTHP) water. Eurofer-97, a ferritic-martensitic steel, has been developed to withstand the conditions of fusion reactors in the locations in contact with coolant with an elevated level of neutron flux, such as the breeder-wall blanket. The material has been studied after self-ion irradiation (using Fe ions) simulating the microstructural effects of neutron irradiation limited to the subsurface layer. The corrosion properties of the Eurofer-97 steel were studied by exposure to HTHP water up to 331 °C. Advanced microstructural characterisation using scanning, transmission electron and focused ion beam microscopy was performed on the as-received microstructure and after ion irradiation. This was then characterised after exposure for 240 h in high-temperature water. Eurofer-97 had a dense, columnar Cr-rich inner oxide, followed by a Fe-rich outer oxide layer. In the irradiated condition the grain structure and oxide itself was less ordered. No appreciable difference in oxide thickness was identified between the irradiated and unirradiated specimens after this short exposure time.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Identifying high-impact and high-uncertainty parameters in MiniFuel model predictions

The MiniFuel irradiation platform at Oak Ridge National Laboratory's High Flux Isotope Reactor (HFIR) is a flexible, high-throughput separate effects test capability. Finite element thermal models are relied upon to design MiniFuel experiments and to achieve experimental objectives. Recent reports show good agreement in the model prediction of target fuel temperatures, but as the capability of the experiments is extended to higher temperatures, the uncertainty in the model predictions must be quantified. To that end, high-impact, high-uncertainty parameters that contribute the most uncertainty to the model are identified. The uncertainty quantification was accomplished through a series of screening and sensitivity analyses. The first analysis utilizes the method of Morris to perform a computationally efficient preliminary screening that considers uncertainty in a large number of the model inputs. The most important parameters identified in the Morris screening study were then considered in a Sobol sensitivity analysis that more robustly ranks and quantifies the uncertainty associated with each parameter. From these analyses, it was determined that thermal contact conductance between components is the parameter that contributes the highest uncertainty. The estimated uncertainty of the MiniFuel model fuel temperature predictions is ±80 °C in the removable beryllium and ±40 °C in the vertical experiment facilities. In conclusion, the framework established by the series of sensitivity analyses presented herein could easily be adapted to fit the needs of accelerated fuel qualification processes.

Fuel, Irradiation↗
DOE OSTI2020

Development of a Reference Model for Molten-Salt-Cooled Pebble-Bed Reactor Using SAM

To support the development and utilization of the SAM code for fluoride-salt-cooled high-temperature pebble-bed reactor (PB-FHR) safety analysis and licensing, an effort was devoted to developing reference models for PB-FHR primary loop and the reactor cavity cooling system (RCCS). A reference standard problem of a prototypical reactor design is foundational to NRC and industry to verify the adequacy of computer codes and evaluation models for a specific reactor type. The SAM code was enhanced for the reference PB-FHR model development, including a 1D-3D flow coupling scheme and conjugate heat transfer between porous media and solid structures. The reference FHR primary loop model was developed based on the UC Berkeley Mk1 FHR design with additional design features from the Kairos Power’s KP-FHR core. The PB-FHR core is modeled by a two-dimensional porous medium while the rest of the primary loop is represented by a SAM one-dimensional model. A SAM one-dimensional primary loop model was also developed for comparison using a single channel approach for the reactor core. Furthermore, the water-based NSTF cavity was modeled using SAM multi-dimensional flow module, to assist in evaluating SAM capabilities of modeling the emergency heat removal systems relying on RCCS concepts.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1973

Materials interactions between the thermoelectric converter and the 5kwe reactor system

The integration of a compact thermoelectric converter with a 5-kwe reactor system is described. Material interaction uncertainties study is also presented. This includes degradation of the required austenitic - refractory metal transition joint during operation at high temperatures; loss of corrosion resistance; embrittlement by the presence of hydrogen; and loss of design margin by transport of interstitial elements. Analysis and limited experimental evidence indicate that these potential materials interactions can be adequately controlled. Group 5-2 refractory metals can be utilized without unacceptable adverse effect on system reliability.

Ferry, P. B.↗
NASA NTRS2007

Long Duration Hot Hydrogen Exposure of Nuclear Thermal Rocket Materials

An arc-heater driven hyper-thermal convective environments simulator was recently developed and commissioned for long duration hot hydrogen exposure of nuclear thermal rocket materials. This newly established non-nuclear testing capability uses a high-power, multi-gas, wall-stabilized constricted arc-heater to .produce high-temperature pressurized hydrogen flows representative of nuclear reactor core environments, excepting radiation effects, and is intended to serve as a low cost test facility for the purpose of investigating and characterizing candidate fuel/structural materials and improving associated processing/fabrication techniques. Design and engineering development efforts are fully summarized, and facility operating characteristics are reported as determined from a series of baseline performance mapping runs and long duration capability demonstration tests.

Litchford, Ron J.↗
DOE OSTI2024

Development of a Light-Trapping, Planar-Cavity Receiver for Enclosed Solar Particle Heating

Concentrating solar thermal power (CSP) technology development has recently focused on high efficiency power cycles and chemical reactions that require high operating temperatures. An increase in receiver operating temperatures relative to current commercial CSP technology is necessary to support more efficient, high temperature power cycles or thermochemical processes. Solar receivers operating with heat transfer media temperatures >700 degrees C face various challenges including thermal performance, scalability, thermal-mechanical issues, and receiver service life. In addition, heat transfer media selection for high-temperature processes has been moving towards inert solid particles in Gen3 CSP, and reactive solid media and/or gases in solar thermochemical processes. To overcome the shortcomings and limitations of conventional designs for molten salt or particle receivers and receiver reactors, we introduce a unique light-trapping, planar cavity receiver (LTPCR) configuration and will present the current development progresses to demonstrate receiver feasibility through modeling, testing, and prototype demonstration.

ENGINEERING,SOLAR ENERGY↗
DOE OSTI2023

Qualification of Commercially Available Silicon Carbide for Passive Thermometry in Reactor Experiments – FY23 Status Report

Silicon carbide (SiC) is often used as a passive temperature indicator for uninstrumented in-core nuclear experiments. For the past several decades, Oak Ridge National Laboratory has relied primarily on SiC thermometry manufactured by Dow Chemical Company, formerly Rohm and Haas because of the material’s high density and reduced grain boundary elements. Although Dow SiC has performed well in this application, this material is no longer commercially available, and a new supplier is needed for future experiments. To determine a suitable replacement, a study was initiated on five types of SiC from four commercial vendors. Several critical properties, including density, electrical resistivity, chemical purity, grain structure, crystal structure, and strength were measured in samples from each material. Additionally, thermometry specimens were manufactured for irradiation in the High Flux Isotope Reactor at nominal temperatures of 300°C, 600°C, and 900°C, which will be measured using continuous dilatometry at a later date. This report provides an update of commercially available SiC material characterization and the irradiation capsule design.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1978

A 5-GWe nuclear satellite power system conceptual design

This paper presents the results of a brief study performed for MSFC on the conceptual design of a nuclear satellite power station which delivers 5 GWe net power to earth by microwave transmission. The system contains 26 modules each consisting of a reactor, fuel processing plant, Brayton PCU, space radiator, and nuclear shield. A high-temperature, gas-cooled, pebble-bed plutonium breeder concept was selected which is resupplied with fertile U-238. Sections of this core are periodically replaced and the spent fuel is chemically processed, the radioactive wastes separated, and stored for eventual space disposal. Fresh fuel pellets, formed from the U-238 and the bred plutonium, are recycled back to the reactor. The hot (1317 C) helium gas exiting the reactor serves as the working fluid in a 30%-efficient Brayton PCU.

Goodman, M.↗
NASA NTRS2016

Development of Advanced ISS-WPA Catalysts for Organic Oxidation at Reduced Pressure/Temperature

The Water Processor Assembly (WPA) at International Space Station (ISS) processes a waste stream via multi-filtration beds, where inorganic and non-volatile organic contaminants are removed, and a catalytic reactor, where low molecular weight organics not removed by the adsorption process are oxidized at elevated pressure in the presence of oxygen and elevated temperature above the normal water boiling point. Operation at an elevated pressure requires a more complex system design compared to a reactor that could operate at ambient pressure. However, catalysts currently available have insufficient activity to achieve complete oxidation of the organic load at a temperature less than the water boiling point and ambient pressure. Therefore, it is highly desirable to develop a more active and efficient catalyst at ambient pressure and a moderate temperature that is less than water boiling temperature. This paper describes our efforts in developing high efficiency water processing catalysts. Different catalyst support structures and coating metals were investigated in subscale reactors and results were compared against the flight WPA catalyst. Detailed improvements achieved on alternate metal catalysts at ambient pressure and 200 F will also be presented in the paper.

Yu, Ping↗
NASA NTRS2020

Developmental Efforts of an Electrochemical Oxygen Recovery System for Advanced Life Support

The current State of Art (SOA) Environmental Control and Life Support System (ECLSS) oxygen recovery system onboard the International Space Station (ISS) is complex, heavy, and power consuming system that recovers approximately 50% of the oxygen (O2) from metabolic carbon dioxide (CO2). For future long-duration missions, O2 recovery systems will need to be highly reliable, efficient, and recover maximum metabolic CO2. A minimum of 75% O2 recovery is required for future O2 recovery systems. Investigations into various technologies to help meet these requirements for exploration are ongoing; however, most of these proposed technologies ultimately result in a more complex system. A Macrofluidic Electrochemical Reactor (MFECR) is one proposed technology development effort currently underway at NASA Marshall Space Flight Center (MSFC) that has the potential to significantly reduce the complexity of ECLSS O2 recovery system. The MFECR operates at standard conditions, giving it an advantage over other technologies being investigated, which require high temperatures resulting in heavy reactors and high power consumption. The MFECR would replace three pieces of hardware for future ECLSS architectures: the current Carbon Dioxide Reduction Assembly (Sabatier reactor), the Plasma Pyrolysis Assembly (PPA), and the Oxygen Generation Assembly (OGA). It is designed to interface directly with the Carbon Dioxide Removal Assembly (CDRA) and the Water Processor Assembly (WPA). This allows for a less complex system and higher reliability than the current SOA as well as reduced power, weight and H2O consumption of ECLSS. Here, we will discuss the current technology development efforts of the MFECR and how this technology may aide in the advancement of future long-duration life support systems.

Brown, Brittany R.↗
NASA NTRSDate not supplied

Developmental Efforts of an Electrochemical Oxygen Recovery System for Advanced Life Support

The current State of Art (SOA) Environmental Control and Life Support System (ECLSS) oxygen recovery system onboard the International Space Station (ISS) is a complex, heavy, and power consuming system that recovers approximately 50% of the oxygen (O2) from metabolic carbon dioxide (CO2). For future long-duration missions, O2recovery systems will need to be highly reliable, efficient, and recover maximum metabolic CO2. Investigations into various technologies to help meet these requirements for exploration are ongoing; however, most of these proposed technologies ultimately result in a more complex system. A Macrofluidic Electrochemical Reactor (MFECR) is one proposed technology development effort currently underway at NASA Marshall Space Flight Center (MSFC) that has the potential to significantly reduce the complexity of ECLSSO2recovery system. The MFECR operates at standard conditions, giving it an advantage over other technologies being investigated, which require high temperatures resulting in heavy reactors and high power consumption. The MFECR would replace three pieces of hardware for future ECLSS architectures: the current Carbon Dioxide Reduction Assembly (Sabatier reactor), the Plasma Pyrolysis Assembly (PPA), and the Oxygen Generation Assembly(OGA). It is designed to interface directly with the Carbon Dioxide Removal Assembly (CDRA) and the Water Processor Assembly (WPA). This allows for a less complex system and higher reliability than the current SOA as well as reduced power, weight and H2Oconsumption of ECLSS. Here, we will discuss the current development efforts of the MFECR and how this technology may aide in the advancement of future long-duration life support systems.

Brittany R Brown↗
DOE OSTI2024

Modeling and design of a separate effects irradiation test targeting fission gas release from Cr-doped UO 2

Fission gas release (FGR) from nuclear fuel during operation can diminish heat transfer properties across the pellet-cladding gap and increase the fuel rod internal pressure, thereby posing a concern to fuel reliability and safety during an accident. Enlarging the fuel grain size, which has been shown to improve fission gas retention, can be achieved by doping the fuel feedstock prior to sintering. In this work, the BISON fuel performance code was used to predict FGR from undoped and chromia-doped UO 2 (referred to as Cr-doped UO 2 ) fuel specimens with different grain sizes and across various temperatures. The BISON models identified the irradiation conditions for which FGR is most significant, and a separate effects irradiation experiment in the High Flux Isotope Reactor (HFIR) was then developed targeting those conditions. Further, the experiment leveraged the MiniFuel irradiation capability at Oak Ridge National Laboratory and consisted of 12 fuel specimens of varying grain size and Cr content. A coupling scheme between BISON FGR results and the ANSYS finite element thermal model used for experiment design was formulated to predict cumulative FGR from each fuel specimen based on expected irradiation temperature histories. The fuel samples were fabricated and characterized as a part of this work, and the fuel compositions modeled in BISON were representative of the specimens used in the experiment. This combined modeling and experimental effort aims to study the effect of fuel grain size and Cr content on FGR and to provide simulated BISON FGR results that can be used for future model validation activities.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Comparative analysis of temperature dependent properties of commercial nuclear fuel pellet and surrogates undergoing cracking: A review

A variety of normal and accident scenarios can generate thermal stresses enough to cause cracking in light water reactor (LWR) fuel. To better understand this behavior, cracking experiments have been carried out to induce thermal gradients in fuel pellets via induction heating and direct resistance heating. In this study, Ceria (CeO 2 ) and yttria stabilized zirconia (YSZ) pellets were chosen as a surrogate fuel material for uranium dioxide (UO 2 ). Induction heating was done using copper coils and molybdenum susceptors which heated the surrogates to a threshold temperature that is sufficiently high for the fuel material to conduct current. Thereafter, direct resistance heating was achieved by passing current through the specimen using a DC power supply to introduce volumetric heating to replicate reactor operating conditions. Simultaneous real-time dual imaging of the ceria pellet surface has been designed using optical and infra-red camera system to capture images of cracks and full-field temperature gradients on pellet. It was observed that YSZ pellets need a much higher voltage-current for volumetric heating and do not exhibit the cracking pattern as ceria and UO 2 , hence YSZ was ruled out for further consideration. Ceria was found to be an appropriate surrogate for UO 2 . Furthermore, the experimental set up and test conditions demand the need to primarily understand the thermo-physical, mechanical and optical properties of UO 2 and the surrogates. Thus, it is essential to have an in-depth knowledge about the various temperature dependent properties of UO 2 and CeO 2 for establishing a comparative analysis between the surrogate and UO 2 for conducting experiments.

36 MATERIALS SCIENCE↗