Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “High Explosives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Validation of Reactive Flow Capabilities in PAGOSA

Several reactive flow modeling capabilities are studied and applied to physics problems of interest in the PAGOSA hydrocode with an emphasis on validation. The Davis equation of state and the Arrhenius shock temperature dependent WSD (AWSD) reactive flow model have been implemented by the author in PAGOSA over the last year. These high-explosive modeling options along with the previously existing HE-JWL equation of state and the SURF/SURFplus reactive flow models are discussed, exercised and compared. Validation of the models analyze numerical results against experimental data from cylinder tests, two-stage gas gun experiments and proton radiography (pRad) experiments. Applications of the modeling options are explored involving both HMX based PBX 9501 and TATB based PBX 9502. The effect of mesh size is considered for prediction of phenomena such as corner turning and dead zones, and the relative code performance of the modeling options is discussed.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2020

Simulations of Sweeping Wave Propagation in a Boron Carbide Plate

In February 2020, experiments were conducted at Los Alamos National Laboratory measuring the propagation of a sweeping wave through a plate of boron carbide which was induced by detonating an adjacent charge of high explosive. Six such shots were red and in each case progress of the wave along the exposed surface of the plate was tracked using photon doppler velocimetry (PDV). In this report we discuss calculations performed using the Lagrangian hydrocode FLAG to model data taken from these experiments. We discuss the models chosen for the different experimental components, the choice of mesh (focusing on, both, two- and three-dimensional geometries), and compare the results from these calculations to experimentally-extracted PDV traces. Notably, we find that the PDV traces for this experiment are most faithfully reproduced using the full three-dimensional geometry, even when the mesh resolution for the three-dimensional calculations was significantly lower than the resolution for the corresponding two-dimensional calculations. We attribute this to the geometry of the experimental setup. Moreover, we find only negligible differences for the PDV traces obtained using the sesame table equation of state for boron carbide and the Gruneisen equation of state.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The Multiphysics on Advanced Platforms Project

In 2015, the Lawrence Livermore National Laboratory started development of next-generation multiphysics simulation capabilities for the National Nuclear Security Administration under the Advanced Technologies Development and Mitigation (ATDM) element of the Advanced Simulation and Computing program in collaboration with the Exascale Computing Project (ECP). A key driver for this effort across the NNSA tri-lab was the emergence of advanced high performance computing (HPC) architectures based on heterogeneous compute capabilities, including GPU based systems, as part of the national drive toward exascale computing platforms at multiple Department of Energy (DOE) facilities. Developing a multiphysics code capable of meeting the various simulation needs of the NNSA as defined by the current generation of integrated codes (or ICs), initially developed as part of the Accelerated Strategic Computing Initiative (ASCI) program beginning in 1996, and able to scale to the current 100 petaflop class pre-exascale systems, as well the forthcoming exaflop class computers, is a daunting challenge. To accomplish this ambitious goal, LLNL has embraced two key themes: use of high-order numerical methods and a modular approach to code development. The LLNL next generation effort is organized under the Multi-Physics on Advanced Platforms Project (MAPP). A foundational component of MAPP is the Axom computer science (CS) toolkit which provides infrastructure for the development of modular, performance portable, multi-physics application codes. MARBL is a next-generation application code built on the Axom base to address the modeling needs of the high energy density physics (HEDP) community for simulating high-explosive, magnetic or laser driven experiments such as inertial confinement fusion (ICF), pulsed-power magneto-hydrodynamics (MHD), equation of state (EOS) and material strength studies as part of the NNSA’s stockpile stewardship program (SSP).

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Improvements to the New CTH Code Verification & Validation Test Suite (FY2020)

The CTH multiphysics hydrocode, which is used for a wide range of important calculations, has undertaken in recent years to overhaul its software quality and testing processes. A key part of this effort entailed building a new, robust V&V test suite made up of traditional hydrocode verification problems, such as those listed in the ASC Tri-Lab Test Suite and the Enhanced Tri-Lab Test Suite, as well as validation problems for some of CTHs most frequently used equations of state, materials models, and other key capabilities. Substantial progress towards this goal was made in FY19. In FY20, this test suite has been expanded to include verification and validation tests of the Sesame and JWL equation of state models as well as the Mader verification problem from the Tri-Lab Test Suite and the Blake verification problem - a linear elastic analog to the Hunter problem from the Enhanced Tri-Lab Test Suite. This report documents CTH performance on the new test suite problems. Verification test results are compared to analytic solutions and, for most tests, convergence results are presented. Validation test results are compared to experimental data and mesh refinement studies are included. CTH performs well overall on the new test problems. Convergence rates for the Blake and Mader problems are comparable to those for similar ASC codes. The JWL and Sesame verification tests show good agreement with analytic solutions. Likewise, CTH simulation results show good agreement with experimental validation data for the Sesame and JWL equations of state for the materials tested. Future V&V work will focus on adding tests for other key capabilities like fracture and high explosive models.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Initial conditions for simulations of beam physics in linear induction accelerators

Flash radiography of hydrodynamic experiments driven by high explosives is a well-known diagnostic technique in use at many laboratories. At Los Alamos, the DualAxis Radiographic Hydrodynamic Test (DARHT) facility two linear induction electron accelerators (LIAs) make the bremsstrahlung radiographic source spots for point projection radiographs from orthogonal views. A new LIA, called Scorpius, is presently under development to advance this technology. To better understand electron-beam physics in these LIAs, numerical simulations are frequently performed with the objective of improving the radiography. At Los Alamos we frequently use the TRAK ray-trace and LSP particle-in-cell (PIC) codes to simulate the injector, and the XTR and LAMDA envelope/centroid codes along with LSP to simulate transport of the accelerated beam through the LIAs. The LIA simulations need the injected beam parameters as initial conditions for calculating beam transport and stability. The determination of these initial conditions is the topic of this note.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Simulations of SITI Cookoff Experiments Carried Out with Different Lots of PBX 9502

A pressure dependent cookoff model for PBX 9502 was developed by Hobbs’ et. al. PBX 9502 is composed of 95% by mass triaminotrinitrobenzene (TATB) and a 5% by mass chlorotrifluoroethylene/vinylidine fluoride binder. The objective in this study is to implement this cookoff model in Aria to simulate Sandia Instrumented Thermal Ignition (SITI) experiments that were carried out with different manufacturing lots of PBX 9502. The SITI design consists of solid cylinders (1" diameter × 1" height) of insensitive high explosive (IHE) confined by a cylindrical aluminum case. An electric heater is wrapped around the lateral surface of the case. This heater produces a temperature heating ramp on the outer surface of the case. Internal thermocouples measure the IHE temperature rise from the center to locations close to the IHE-aluminum interface. The energetic material is heated until thermal ignition occurs. Pressure is measured with a static pressure transducer installed on top of the confinement case. Two–dimensional axisymmetric heat conduction finite element models were implemented to simulate these experiments using four options of the PBX 9502 cookoff model. In addition, the predictive ability of this thermal decomposition model is evaluated using Latin Hypercube Sampling (LHS) techniques.

42 ENGINEERING↗
DOE OSTI2021

On Two-Phase Pressure and Temperature Equilibration with Mie-Grüneisen Equations of State

In the course of reactive flow modeling, the phases of high explosive (HE) reactants and products introduce additional degrees of freedom to the underlying hydrodynamic equations of compressible reactive fluid mechanics. Hydrodynamic simulations track the bulk (mixture) conservation properties of mass, momentum and energy. When multiple phases are introduced, one must decide on appropriate closure rules to determine the relative phase volumes and energy distribution between the phases. One typical closure is to assume that the phases are in pressure and temperature equilibrium. Here, the requisite equations of p-T equilibration are explored for Mie-Grüneisen Equations of State (EOS). Examples with Davis reactants and Davis products EOSs will be given. The Davis forms are used in both the WSD and AWSD reactive flow models.

42 ENGINEERING↗
DOE OSTI2021

Photonic Doppler Velocimetry for Valve Analysis and Surveillance

This study is an experimental evaluation to measure and surveil the velocity of stainless steel (Carpenter 455) pistons within a forged 21-6-9 stainless steel valve body. The velocity of the piston “stroke” will be identified using Photonic Doppler Velocimetry (PDV). The piston velocity will be the measured variable of interest. The outcome of this testing series provides further understanding to whether the extracted piston velocity can provide enough information to determine valve integrity. PDV has been identified as a diagnostic of interest as it can detect surface motion at high speeds with reliable accuracy. Through preliminary studies conducted with velocity interferometer system for any reflector (VISAR), the velocity of the piston is expected to stroke with a speed of 135 m/s. The PDV technique is much more reliable and repeatable than the VISAR technique because of its high-speed precision and accuracy, so it will not only validate the preliminary data, but also provide a testing technique that is capable of being used in future valve qualification efforts. The initial testing was completed using valves that were assembled per qualified procedures in a pristine condition. These initial tests were conducted to provide baseline data. This baseline data was then compared to data collected from valves where man-made defects were introduced. These defects are discussed in later sections. Lastly, actuators used to operate the valves were loaded with varied amounts of high explosives to identify if velocity is a function of the amount of explosive in an actuator. These parameters were adjusted to conclusively determine and identify if PDV can be used as a method to assess valve integrity. It was concluded through the testing discussed in this paper that in fact, PDV is capable of measuring the differences in piston velocities based on varied parameters. As far as understanding the PDV accuracy of the measured differences, this is ongoing and will have to be assessed in continued testing series.

42 ENGINEERING↗
DOE OSTI2021

Laser Wavelength Shift from Splitters and Switches

The Detonation Science and Technology Group (Q-6) operates several photon Doppler velocimetry (PDV) systems as a diagnostic tool for measuring velocities in the 1–10 km/s range during high explosive (HE) detonation experiments. Q-6 uses “heterodyne” PDV systems that are produced by Traverse Solutions and Instrumentation, LLC (TS&I). These heterodyne systems combine wavelength (WL) tunable source and “reference” lasers with a WL offset of 10–100 pm from each other. Properly setting the source and reference WLs for an experiment can be critical for collecting the desired experimental data. The tunable lasers report WL readings in their control software, but these readings are based on a lookup table from a temperature reading and are not able to be calibrated. Therefore, recent test fire programs that require PDV as a diagnostic have also implemented requirements for monitoring the WL of the tunable lasers using a precision WL meter. To monitor the WL of several PDV lasers without disconnecting any patch fibers form the experimental setup, Q-6 developed a system splitters with a coupling ratio (%) of 99:1 and an optical switch with the switch output going to a single WL meter. A brief experiment was developed to determine if the splitters and/or switch introduced any WL bias into the readings. The purpose of this report is to document the system, the experiment, and its results.

42 ENGINEERING↗
DOE OSTI2021

Efficient connection of reactive shock wave profiles to reaction models

The future of energetic materials development, especially high-performance high explosives, demands new efficient and cost-effective experimental methods to understand the performance of new materials when only limited, development-scale quantities are available. Indeed, perhaps thousands of new molecules that have promising thermodynamic properties have been synthesized, only to be documented in the literature and never evaluated for their potential due to the cost of scaling up to produce quantities needed for traditional performance measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Modeling soot growth in Comp-B using a detonation history

A chemical kinetics procedure for soot formation calculation is summarized. By importing Lagrangian hydrodynamic calculations, species history is consistently accounted for. Detonation product composition is assumed in region with the burnt high explosive (HE). Soot formation is calculated using the density and energy obtained in the hydrodynamics calculation of HE detonation. Ideal gas equation-of-state (EOS) with temperature-dependent specific heat is used in the HE product region. Sample calculations show reasonably-expected temperature and soot formation.

42 ENGINEERING↗
DOE OSTI2021

High Fidelity Tomographic Density Reconstructions [Slides]

Pressed high explosives have small density variations associated with the pressing process, from a few to sub percent depending on the material. Variations at these levels are known to have an impact on HE performance. Currently, a destructive testing method based on physical sectioning followed by immersion density measurements (slice and dice) is utilized. However, this method has poor spatial resolution limited by the the sectioning size, 1-2 cm. If possible, radiographic methods including Computed Tomography (CT) would be preferred, as they are non-destructive and have higher (less than .1 mm) spatial resolution. However, beam hardening, scattered radiation, and detector effects make density reconstructions at this level extremely challenging.

42 ENGINEERING↗
DOE OSTI2021

R-CERT Project Analysis Report

The R-CERT project aims to determine if PBX 9501 will experience a deflagration to detonation transition (DDT) while in a high pressure environment. Combined efforts in design and analysis between multiple groups at Los Alamos National Laboratory (LANL) were required to finalize the test design. The proposed design of the case assembly (i.e. the pressure vessel that would contain the high explosive) was analyzed and iteratively modified until modeling efforts predicted the case would maintain pressure up to 5000 psi under quasi-static conditions. To prevent the case from being excessively robust beyond its design requirement, grooves were added to the case geometry with depths and radii of 4 mm, thus weakening the case while maintaining much of the mass of the proposed design.

42 ENGINEERING↗
DOE OSTI2021

Nonproliferation and Arms Control Research and Development (NPAC R&D) [Slides]

NPAC R&D focus areas include: Advancing U.S. capabilities to detect and characterize nuclear weapon development activities globally, including material production, the movement of special nuclear materials and nuclear weapons, and the testing or use of nuclear weapons, Supporting the development and testing of policy options and technical capabilities for international nuclear safeguards, arms control / treaty verification, nuclear export controls, and nonproliferation initiatives consistent with U.S. Government goals and objectives to enable monitoring and verification, Utilizing uranium, lithium, and high explosives (HE) materials expertise to support national-level activities in nuclear forensics and nuclear detection technology testing and evaluation, Providing unique training and capacity-building programs, particularly with the Nuclear Detection and Sensor Testing Center (NDSTC), and Engaging internationally to promote nonproliferation and arms control norms and best practices through bilateral and multilateral work.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Structural Health Monitoring: Using an Autoencoder to Identify Damage in a Bolted Joint [Capstone Project]

Los Alamos National Laboratory (LANL) is an important fixture in the United States Department of Energy’s (DOE) National Nuclear Security Agency (NNSA) complex. LANL is one of the largest national laboratories in the country, and the laboratory’s primary mission is to support the nation’s nuclear stockpile. The lab functions as a design agencies for the NNSA and performs extensive testing on weapons as part of that mission. The shock and vibration test team at LANL utilizes electrodynamic shaker systems for important qualification testing in support of the laboratory’s mission. Modern engineering relies heavily on bolted joints to connect two objects. During these shaker tests, engineers depend on bolted joints to secure the test article to a fixture and the fixture to the table. The test article may be hazardous and contain high explosives which could create a safety issue if a bolted joint failed. A loss of preload in a bolt will affect the way energy is input to the system and may introduce nonlinearities as the joint opens and closes. The loss of preload can create challenges controlling the test and make acquired signals useless. Being able to monitor preload within bolted joints during testing can improve the quality of the data and keep workers safe.

42 ENGINEERING↗
DOE OSTI2021

Global Security & Strategic Partnerships Programs

Serving the Nation: Our Missions include Providing the Nuclear Deterrent for our Nation and Allies; Leading Nuclear Nonproliferation and Counterterrorism / Counterproliferation efforts to make the world a safer place; Supplying Enriched Uranium Material for Reactors – Naval Propulsion, Army, NASA, Universities, Isotope Production Reactors; Providing High Explosives for the Stockpile and Strategic Partners; Delivering Solutions – Solve emerging national security challenges

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Numerical Simulations of Non-Proliferation Experiments

We have implemented a set of numerical simulations to numerically investigate the outcomes of non-proliferation experiments. The high explosive (HE) in the simulations is in the form of a cylinder. The two-dimensional simulations are carried out in the r-z cylindrical coordinate, and the three-dimensional simulation is in the Cartesian coordinate. From the simulation, the cavity formed after detonation stops its expansion after about 0.15 sec. At the time the cavity stops expanding, the cavity shape seems quite spherical although the initial HE is in the shape of cylinder, but the radius in the vertical direction, which is about 19.7m, is a little less than the one in the horizonal direction, which is about 21.5m. Although there is no layer of air between the HE and tuff in real experiments, in addition to the simulations without air, we add a layer of air in one simulation to assess any possible influence of the air on the shape of the cavity.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2022

FY2021 Improvements to the New CTH Code Verification & Validation Test Suite

Over the past few years, the CTH multiphysics hydrocode has overhauled its software quality and testing processes, implementing current best practices in software quality and building a robust V&V test suite comprised of traditional hydrocode verification problems, including ASC Tri-Lab Test Suite and Enhanced Tri-Lab Test Suite problems, as well as validation problems for some of CTH’s most frequently used equations of state, materials models, and other key capabilities. Substantial progress towards building this new test suite was made in FY19 and FY20. In FY21, the test suite has been expanded to include verification and validation tests of the Steinberg-Guinan-Lund (ST) viscoplastic model and the Johnson Cook (JFRAC) fracture model. Additionally, two new verification tests were added, covering hydrodynamics and high explosive (HE) modeling capabilities: the Kidder Gaussian density problem and the Escape of HE Products (EHEP) problem from the Tri-Lab Test Suite. This report discusses each of these test problems in detail. Verification test results are compared to analytic solutions. Validation test results are compared to experimental data. Wherever possible, convergence or mesh refinement studies are included. Additionally, while implementing the Kidder verification problem, a bug was identified that affects the use of tables to initialize pressure or density in 1D or 2D calculations. A brief discussion of the bug and its fix is included. CTH demonstrates good performance overall on the new test suite problems. Simulation results showed good agreement with analytic solutions for the Kidder problem, with convergence rates ranging between 1.8 and sub-linear, and relatively good agreement for the EHEP problem, though convergence rates for pressure and density were nearly 0. The ST and JFRAC strain rate loading verification tests show good agreement with analytic solutions. Likewise, CTH simulation results show good agreement with experimental validation data, including Taylor rod impact testing, for the materials tested. Future V&V work will focus on adding 2D and 3D versions of existing verification tests as well as adding validation tests of other frequently used capabilities such as other fracture models.

42 ENGINEERING↗