Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GRINDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Microeconomic analysis of military aircraft bearing restoration

The risk and cost of a bearing restoration by grinding program was analyzed. A microeconomic impact analysis was performed. The annual cost savings to U.S. Army aviation is approximately $950,000.00 for three engines and three transmissions. The capital value over an indefinite life is approximately ten million dollars. The annual cost savings for U.S. Air Force engines is approximately $313,000.00 with a capital value of approximately 3.1 million dollars. The program will result in the government obtaining bearings at lower costs at equivalent reliability. The bearing industry can recover lost profits during a period of reduced demand and higher costs.

Hein, G. F.↗

Preparation of zinc orthotitanate

Use of decomposable precursors to enhance zinc oxide-titanium dioxide reaction and rapid fixing results in rapid preparation of zinc orthotitanate powder pigment. Preparation process allows production under less stringent conditions. Elimination of powder grinding results in purer that is less susceptible to color degradation.

Gates, D. W.↗

Restoration of bearings

Process consisting of grinding raceways to oversize but original quality condition and installing new oversize balls or bearings restores wornout ball and roller bearings to original quality, thereby doubling their operating life. Evaluations reveal process results in restoration of 90% of replaced bearings at less than 50% of new-bearing costs.

Parker, R. J.↗

Feasibility investigation of integrated optics Fourier transform devices

The possibility of producing an integrated optics data processing device based upon Fourier transformations or other parallel processing techniques, and the ways in which such techniques may be used to upgrade the performance of present and projected NASA systems were investigated. Activities toward this goal include; (1) production of near-diffraction-limited geodesic lenses in glass waveguides; (2) development of grinding and polishing techniques for the production of geodesic lenses in LiNbO3 waveguides; (3) development of a characterization technique for waveguide lenses; and (4) development of a theory for corrected aspheric geodesic lenses. A holographic subtraction system was devised which should be capable of rapid on-board preprocessing of a large number of parallel data channels. The principle involved is validated in three demonstrations.

Verber, C. M.↗

Method of treating the surface of a glass member

A method is described of treating a surface of a glass member intended to abut a transparent element for disrupting the light interference fringes formed between the surfaces. The method involves the steps of grinding the surface to form irregularities thereon; bathing the surface with an aqueous solution containing between substantially 41.3 percent and 45.7 percent by volume of sulfuric acid and between substantially 54.3 percent and 58.7 percent by volume of hydrofluoric acid for a time sufficient to polish the irregularities until the glass member is about 90 percent light transmissive; and washing the glass member with a liquid having a temperature substantially lower than the temperature of the aqueous solution for preventing further reaction between the aqueous solution and the surface.

Rice, S. H.↗

Ferromagnetic resonance studies of lunar core stratigraphy

We first review the evidence which links the characteristic ferromagnetic resonance observed in lunar fines samples with agglutinatic glass produced primarily by micrometeorite impacts and present new results on Apollo 15, 16, and 17 breccias which support this link by showing that only regolith breccias contribute significantly to the characteristic FMR intensity. We then provide a calibration of the amount of Fe metal in the form of uniformly magnetized spheres required to give our observed FMR intensities and discuss the theoretical magnetic behavior to be expected of Fe spheres as a function of size. Finally, we present FMR results on samples from every 5 mm interval in the core segments 60003, 60009, and 70009. These results lead us to suggest: (1) that secondary mixing may generally be extensive during regolith deposition so that buried regolith surfaces are hard to recognize or define; and (2) that local grinding of rocks and pebbles during deposition may lead to short scale fluctuations in grain size, composition, and apparent exposure age of samples.

Housley, R. M.↗

Mounting procedure for geological samples

Mounting procedure originally developed for lunar samples preserves geological specimens. Sequence of potting and grinding operations produces thin sections through grains that are easy to handle and are well protected for storage. Method results in more representative sections of mixture of grains of different sizes and more effective distribution of grains uniformly over slide.

Jezek, D. I.↗

Rocketdyne's advanced coal slurry pumping program

The Rocketdyne Division of Rockwell International Corporation is conducting a program for the engineering, fabrication, and testing of an experimental/prototype high-capacity, high-pressure centrifugal slurry feed pump for coal liquefaction purposes. The abrasion problems in a centrifugal slurry pump are primarily due to the manner in which the hard, solid particles contained in the slurry are transported through the hydraulic flow passages within the pump. The abrasive particles can create scraping, grinding, cutting, and sandblasting effects on the various exposed parts of the pump. These critical areas involving abrasion and impact erosion wear problems in a centrifugal pump are being addressed by Rocketdyne. The mechanisms of abrasion and erosion are being studied through hydrodynamic analysis, materials evaluation, and advanced design concepts.

Davis, D. E.↗

Determination of the pure silicon monocarbide content of silicon carbide and products based on silicon carbide

Experience has shown that different methods of analysis of SiC products give different results. Methods identified as AFNOR, FEPA, and manufacturer P, currently used to detect SiC, free C, free Si, free Fe, and SiO2 are reviewed. The AFNOR method gives lower SiC content, attributed to destruction of SiC by grinding. Two products sent to independent labs for analysis by the AFNOR and FEPA methods showed somewhat different results, especially for SiC, SiO2, and Al2O3 content, whereas an X-ray analysis showed a SiC content approximately 10 points lower than by chemical methods.

Prost, L.↗

Determination of oxygen in silicon and carbide by activation with 27.2 meV alpha particles

The Si sample was polished on one side, and on the other side Ni was applied chemically and soldered with Pb to a water cooled Cu substrate. Optical quartz standard was fixed from the other side. Si carbide samples were soldered to a substrated with In. The prepared samples were irradiated in a cyclotron with a 27.2 MeV alpha particle beam. The layers were removed from the Si and Si carbide samples by grinding and the positron activity of F-18(t sub 1/2 110 min) was measured by using a gamma, gamma coincidence spectrometer with two NaI(TI) crystals. For analysis of Si carbide, the activity decay curve of the samples was recorded to find the contribution of the positron activity of Cu-65(t sub 1/2 12.9 hr) which formed from Ni impurity on irradiation.

Dolgolenko, A. P.↗

Effect of attrition milling on the reaction sintering of silicon nitride

Silicon powder was ground in a steel attrition mill under nitrogen. Air exposed powder was compacted, prefired in helium, and reaction sintered in nitrogen-4 v/o hydrogen. For longer grinding times, oxygen content, surface area and compactability of the powder increased; and both alpha/beta ratio and degreee of nitridation during sintering increased. Iron content remained constant.

Herbell, T. P.↗

Cleaning process for contaminated superalloy powders

A cleaning process for removing interstitial contaminants from superalloy powders after wet grinding is described. Typical analyses of oxygen, carbon, nitrogen, and hydrogen in ball-milled WAZ-20 superalloy samples after hydrogen plus vacuum cleaning are presented. The hydrogen cleaning step involves heating retorts containing superalloy powder twice under flowing hydrogen with a 24-hour hold at each temperature. The vacuum step involves heating cold-pressed billets two hours at an elevated temperature at a pressure of 10 microPa. It is suggested that the hydrogen plus vacuum cleaning procedure can be applied to superalloys contaminated by other substances in other industrial processes.

Anglin, A. E.↗

Effect of attrition milling on the reaction sintering of silicon nitride

Silicon powder was ground in a steel attrition mill under nitrogen. Air-exposed powder was compacted, prefired in helium, and reaction-sintered in nitrogen-4 v/o hydrogen. For longer grinding times, oxygen content, surface area and compactability of the powder increased; and both alpha/beta ratio and degree of nitridation during sintering increased. Iron content remained constant.

Herbell, T. P.↗

Study program to develop and evaluate die and container materials for the growth of silicon ribbons

Initial sessile drop experiments on SiC, Si3N4 and A1N were conducted. Very promising results were achieved on both SiC and Si3N4 where minimal penetration of these CNTD coatings by molten silicon was observed. More detailed characterization of the CNTD microstructures was accomplished as well as X-ray characterization of the third and fourth candidate materials system sets (i.e. A1N and altered Si3N4). Polished sections of post sessile drop specimens were also prepared and evaluated. The techniques of full scale crucible hot pressing were developed and die grinding development was initiated. The apparatus for measurement of oxygen partial pressure was reconstructed and calibrated. The sessile drop temperature measurement procedure was calibrated for absorption by the pyrex view-port and additional Auger electron analysis was performed at the interface of molten silicon with CNTD Si3N4 and A1N.

Source record↗

Tribological properties of silicon carbide in metal removal process

Material properties are considered as they relate to adhesion, friction, and wear of single crystal silicon carbide in contact with metals and alloys that are likely to be involved in a metal removal process such as grinding. Metal removal from adhesion between sliding surfaces in contact and metal removal as a result of the silicon carbide sliding against a metal, indenting into it, and plowing a series of grooves or furrows are discussed. Fracture and deformation characteristics of the silicon carbide surface are also covered. The adhesion, friction, and metal transfer to silicon carbide is related to the relative chemical activity of the metals. The more active the metal, the higher the adhesion and friction, and the greater the metal transfer to silicon carbide. Atomic size and content of alloying elements play a dominant role in controlling adhesion, friction, and abrasive wear properties of alloys. The friction and abrasive wear (metal removal) decrease linearly as the shear strength of the bulk metal increases. They decrease as the solute to solvent atomic radius ratio increases or decreases linearly from unity, and with an increase of solute content. The surface fracture of silicon carbide is due to cleavages of 0001, 10(-1)0, and/or 11(-2)0 planes.

Miyoshi, K.↗

Study of composites as substrate materials in large space telescopes

Nonmetallic composites such as the graphite/epoxy system were investigated as possible substrates for the primary mirror of the large space telescope. The possible use of fiber reinforced metal matrix composites was reviewed in the literature. Problems arising out of the use of composites as substrate materials such as grinding, polishing, adherence of reflective coatings, rigidity of substrate, hygrospcopici tendency of the composites, thermal and temporal stability and other related problems were examined.

Sharma, A. V.↗

Method of forming a sharp edge on an optical device

A sharp edge is formed on an optical device by placing the optical device in a holding mechanism; grinding one surface so that it and a surface of the holding mechanism are co-planar; and polishing both the surface of the optical device and the surface of the holding mechanism with felt until an edge on the surface of the optical device adjacent to the surface of the holding mechanism obtains a desired sharpness.

Fleetwood, C. M.↗

A rapid implicit-explicit solution to the two-dimensional time dependent incompressible Navier-Stokes equations

A second-order time-accurate and spatially factored algorithm was used in a finite difference scheme for the numerical solution of the time-dependent, incompressible, two dimensional Navier-Stokes equations in conservation-law form using vorticity and stream function variables. The systems of equations are solved at each time step by an iterative technique. Numerical results were obtained for a circular cylinder at a Reynolds number of 15, and an NACA 0012 airfoil at zero angle of attack at Reynolds numbers of 10 to the third and 10 to the fourth powers. The results are in agreement with another numerical technique, and the computing time required to obtain the steady state solution at the Reynolds number of 10 to the 4th power was 49.7 sec on CDC 7600 computer using a 65 x 84 computational grind.

Davis, J. E.↗