Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GREEN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31

Role of V-defect density on the performance of III-nitride green LEDs on sapphire substrates

In this paper, we experimentally investigated the role of V-defect density on the performance of green III-nitride LEDs grown on sapphire substrates by metalorganic chemical vapor deposition. We systematically varied the threading dislocation (TD) density from 4 × 10 8 to 1 × 10 9 cm -2 by changing the V/III ratio during initial high temperature GaN growth. A 30-period InGaN/GaN superlattice promoted V-defect formation and growth at TDs, where the density of V-defects was correlated to the TD density. By interrupting the LED growth and examining the surface of the active region, we quantified the average size and density of V-defects. In a series of LEDs, we measured a systematic decrease in forward voltage (V F ) with V-defect density. At a V-defect density of 5.0 × 10 8 cm -2 and TD density of 1 × 10 9 cm -2 , green LED devices were demonstrated with λ = 523 nm and V F = 2.94 V at 20 A cm -2 . These results highlight the potential of using V-defect engineering to achieve low V F long wavelength LEDs on sapphire substrates, where opening of remaining threading dislocations into V-defects presents an opportunity for further V F reduction.

36 MATERIALS SCIENCE↗

Optical properties of green-blue-emitting Ca-{alpha}-Sialon:Ce{sup 3+},Li{sup +} phosphors for white light-emitting diodes (LEDs)

Ce{sup 3+},Li{sup +}-codoped Ca-{alpha}-Sialon phosphors with the formula [Ca{sub (1-2x)}Ce{sub x}Li{sub x}]{sub m/2}Si{sub 12-(m+n)}Al{sub m+n}O{sub n}N{sub 16-n} (0{<=}x{<=}0.25, 0.5{<=}m{<=}3.5, and 0.16{<=}n{<=}2.0) have been synthesized by gas pressure sintering (GPS). The effects of the activator concentration and the overall composition of host lattice on the phase evolution, morphology, and optical properties were investigated. The single-phase Ca-{alpha}-Sialon:Ce{sup 3+},Li{sup +} can be synthesized at x<0.1, 1.0{<=}m{<=}2.5, and n{<=}1.2. The synthesized powders exhibit a relatively dispersive and uniform morphology. Under the near UV excitation, the bright green-blue emission centered at 500-518 nm is observed. The photoluminescence can be tailored by controlling Ce{sup 3+} concentration and the overall composition of the {alpha}-Sialon host lattice. With increasing the Ce concentration and m value both excitation and emission bands show a red shift, which perfectly matches with the near-UV LEDs in the range of 360-410 nm. The strongest luminescence is achieved at x=0.08-0.1, m=2.0-2.5, and n=1.0. Simultaneously, the highest quantum efficiency and better thermal stability are also present. -- Graphical abstract: Dependence of photoluminescence intensity and normalized photoluminescence spectra (the inset) of Ca-{alpha}-Sialon:Ce{sup 3+},Li{sup +} on the host lattice composition: (a) m value and (b) n value Display Omitted Highlights: {yields} The optical properties of [Ca{sub (1-2x)}Ce{sub x}Li{sub x}]{sub m/2}Si{sub 12-(m+n)}Al{sub m+n}O{sub n}N{sub 16-n} (0{<=}x{<=}0.25, 0.5{<=}m{<=}3.5, 0.16{<=}n{<=}2.0) have been investigated. {yields} Excited by near UV, the bright green emission centered at 500-518 nm is observed. {yields} The photoluminescence can be tailored by controlling Ce{sup 3+} content and host lattice composition. {yields} The strongest luminescence is achieved at x=0.08-0.1, m=2.0-2.5, and n=1.0. {yields} The highest quantum efficiency and better thermal stability are also present.

36 MATERIALS SCIENCE↗

A green chemical approach to the synthesis of photoluminescent ZnO hollow spheres with enhanced photocatalytic properties

ZnO hollow spheres have been synthesized by a simple and environmentally friendly template assisted route. Starch-derived carbonaceous spheres were used as template, impregnated with Zn(CH{sub 3}COO){sub 2}{center_dot}2H{sub 2}O to obtain zinc-containing precursor spheres and thermally treatment at 600 Degree-Sign C, yielding hollow ZnO spherical shells. The precursor spheres and hollow shells were characterized by X-ray diffraction, FTIR spectroscopy, scanning electron microscopy, thermal analysis and room-temperature photoluminescence measurements. The hollow spherical shells with diameters of {approx}150 nm and wall thickness of {approx}20 nm, are polycrystalline, with a mean crystallite size of 22 nm, exhibiting interesting emission features, with a wide multi-peak band covering blue and green regions of the visible spectrum. The photocatalytic activities (under UV and visible light irradiations) of the ZnO spherical shells evaluated for the phenol degradation reaction in aqueous solutions are outstanding, a total phenol conversion being registered in the case of UV irradiation experiments. - Graphical abstract: The photocatalytic reaction initiated by the photoexcitation of the semiconductor (ZnO), leads to the formation of electron-hole, while part of the electron-hole pairs recombine, some holes combine with water to form {center_dot}OH radicals and some electrons convert oxygen to super oxide radical ({center_dot}O{sub 2}{sup -}). Highlights: Black-Right-Pointing-Pointer Green synthesis of ZnO hollow spheres. Black-Right-Pointing-Pointer Starch-derived carbonaceous spheres as spherical hard template. Black-Right-Pointing-Pointer ZnO hollow spheres with notable visible photoluminescence properties. Black-Right-Pointing-Pointer ZnO hollow spheres with photocatalytical activity in degradation/mineralization of phenol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Preparation, characterization and catalytic properties of MCM-48 supported tungstophosphoric acid mesoporous materials for green synthesis of benzoic acid

MCM-48 and tungstophosphoric acid (HPW) were prepared and applied for the synthesis of HPW/MCM-48 mesoporous materials. The characterization results showed that HPW/MCM-48 obtained retained the typical mesopore structure of MCM-48, and the textural parameters decreased with the increase loading of HPW. The catalytic oxidation results of benzyl alcohol and benzaldehyde with 30% H{sub 2}O{sub 2} indicated that HPW/MCM-48 was an efficient catalyst for the green synthesis of benzoic acid. Furthermore, 35 wt% HPW/MCM-48 sample showed the highest activity under the reaction conditions. Highlights: • 5–45 wt% HPW/MCM-48 mesoporous catalysts were prepared and characterized. • Their catalytic activities for the green synthesis of benzoic acid were investigated. • HPW/MCM-48 was approved to be an efficient catalyst. • 5 wt% HPW/MCM-48 exhibited the highest catalytic activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Novel bipyridinyl oxadiazole-based metal coordination complexes: High efficient and green synthesis of 3,4-dihydropyrimidin-2(1H)-ones through the Biginelli reactions

Three new metal coordination complexes, namely, [Co(BPO){sub 2}(H{sub 2}O){sub 4}](BS){sub 2}(H{sub 2}O){sub 2} (1), [Co(BPO){sub 2}(H{sub 2}O){sub 4}](ABS){sub 2}(H{sub 2}O){sub 2} (2), [Co(BPO){sub 2}(H{sub 2}O){sub 4}](MBS){sub 2}(H{sub 2}O){sub 2} (3) [BPO=2,5-di(pyridin-4-yl)-1,3,4-oxadiazole, BS=benzenesulphonate, ABS=4-aminobenzenesulphonate, MBS=4-methylbenzenesulphonate] were obtained under hydrothermal conditions. Complexes 1–3 were structurally characterized by single-crystal X-ray diffraction, powder X-ray diffraction, IR and thermogravimetric analyses (TGA). All of them display a zero-dimensional motif, in which strong intermolecular hydrogen bonding interactions (O–H···O/N) and packing interactions (C–H···π and π···π) make them achieve a three-dimensional supramolecular architecture. The primary catalytic results of these three complexes show that high efficiency for the green synthesis of a variety of 3,4-dihydropyrimidin-2(1H)-ones was observed under solvent free conditions through Biginelli reactions. The present catalytic protocols exhibit advantages such as excellent yield, easy isolation, eco-friendly conditions, and short reaction time. - Graphical abstract: Three new metal coordination complexes with bipyridinyl-oxadiazole were obtained under hydrothermal conditions, which display a zero-dimensional motif, and show high efficiency for the green synthesis of a variety of 3,4-dihydropyrimidin-2(1H)-ones under solvent free conditions through Biginelli reactions. The present catalytic protocols exhibit advantages such as excellent yield, easy isolation, eco-friendly conditions, and short reaction time. Display Omitted.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of carbon silica hybrid fillers obtained by pyrolysis of waste green tires by the STEM–EDX method

Dual phase carbon–silica hybrid fillers obtained by pyrolysis-cum-water vapor of waste green tires have been characterized by energy dispersive X-ray spectroscopy in a scanning transmission electron microscope, silicate analysis, weight analysis, atomic absorption spectroscopy and by inductively coupled plasma–optical emission spectroscopy. The results achieved have shown that the location and distribution of the phases in the carbon silica hybrid fillers as well as their most essential characteristics are influenced by the pyrolysis conditions. The carbon phase of the filler thus obtained is located predominantly in the space among silica aggregates which have already been existing while it has been formed by elastomer destruction in the course of pyrolysis. The presence of ZnS also has been found in the hybrid fillers investigated. - Highlights: • Dual phase fillers obtained by pyrolysis of waste green tires have been characterized. • The STEM–EDX method was used for characterization. • The phase distributions in the fillers are influenced by the pyrolysis conditions.

36 MATERIALS SCIENCE↗

Green emission from Eu{sup 2+}/Dy{sup 3+} codoped SrO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3} glass-ceramic by ultraviolet light and femtosecond laser irradiation

A spectroscopic investigation of Eu{sup 2+}/Dy{sup 3+} codoped SrO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3} glass-ceramic is presented. The sample exhibits green emission excited by ultraviolet (UV) light and near-IR femtosecond (fs) laser. The emission profile obtained by near-IR fs laser irradiation is similar to that by UV excitation, indicating that both of the emissions come from 5d {yields} 4f transition of the Eu{sup 2+} ions. The relationship between the upconversion luminescence (UCL) intensity and pump power reveals a two-photon process in the conversion of near-IR radiation to the green emission. The possible mechanism of UCL from such glass-ceramic is proposed.

36 MATERIALS SCIENCE↗

Pumping-route-dependent concentration quenching and temperature effect of green up- and down-conversion luminescence in Er{sup 3+}/Yb{sup 3+} co-doped Gd{sub 2}(WO{sub 4}){sub 3} phosphors

Graphical abstract: A comparative study on the concentration quenching behaviors of green down- and up-conversion emissions was carried out for the first time, and the different concentration quenching mechanisms were analyzed. Secondly, the thermal effect induced by 980 nm LD irradiation was investigated, it was observed that the equilibrium temperature of Gd{sub 2}(WO{sub 4}){sub 3}:Er{sup 3+}/Yb{sup 3+} sample was decided by both the excitation power and Er{sup 3+} doping concentration. Highlights: ► Gd{sub 2}(WO{sub 4}){sub 3}:Er/Yb phosphors were prepared via a co-precipitation reaction. ► Morphology and structure of the phosphors were characterized by XRD and SEM. ► Concentration quenching mechanisms for down and up emissions were studied. ► Thermal effect induced by laser irradiation was studied via temperature sensing tech. - Abstract: Gd{sub 2}(WO{sub 4}){sub 3} phosphors with various Er{sup 3+} concentrations and fixed Yb{sup 3+} concentration were synthesized via a co-precipitation method, and their crystal structure and morphology were characterized by using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The concentration quenching behaviors of green up- and down-conversion emissions of Er{sup 3+} were analyzed, and it was confirmed that the difference between quenching concentration for up- and down-conversion emissions resulted from the different population routes. The temperature sensing properties of the Gd{sub 2}(WO{sub 4}){sub 3}:Er{sup 3+}/Yb{sup 3+} phosphors were studied, and it was found that the Er{sup 3+} doping concentration slightly affected the sensitivity, and Gd{sub 2}(WO{sub 4}){sub 3}:Er{sup 3+}/Yb{sup 3+} phosphors could be used in a broad temperature region for detecting temperature. Finally, the thermal effect induced by 980 nm LD irradiation was investigated, it was observed that the equilibrium temperature of Gd{sub 2}(WO{sub 4}){sub 3}:Er{sup 3+}/Yb{sup 3+} sample was decided by both the excitation power and Er{sup 3+} doping concentration.

36 MATERIALS SCIENCE↗

Noncovalently-functionalized reduced graphene oxide sheets by water-soluble methyl green for supercapacitor application

Graphical abstract: Electroactive methyl green (MG) is selected to functionalize reduced graphene oxide (RGO) through non-covalent modification and the composite achieves high specific capacitance, good rate capability and excellent long life cycle. - Highlights: • MG–RGO composites were firstly prepared through non-covalent modification. • The mass ratio in composites is a key for achieving high specific capacitance. • MG–RGO 5:4 exhibits the highest specific capacitance of 341 F g{sup −1}. • MG–RGO 5:4 shows excellent rate capability and long life cycle. - Abstract: In the present work, water-soluble electroactive methyl green (MG) has been used to non-covalently functionalize reduced graphene oxide (RGO) for enhancing supercapacitive performance. The microstructure, composition and morphology of MG–RGO composites are systematically characterized by UV–vis absorption, field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The electrochemical performances are investigated by cyclic voltammetry (CV), galvanostatic charge/discharge and electrochemical impedance spectroscopy (EIS). The fast redox reactions from MG could generate additional pseudocapacitance, which endows RGO higher capacitances. As a result, the MG–RGO composite (with the 5:4 mass ratio of MG:RGO) achieve a maximum value of 341 F g{sup −1} at 1 A g{sup −1} within the potential range from −0.25 to 0.75 V and provide a 180% enhancement in specific capacitance in comparison with pure RGO. Furthermore, excellent rate capability (72% capacitance retention from 1 A g{sup −1} to 20 A g{sup −1}) and long life cycle (12% capacitance decay after 5000 cycles) are achieved for the MG–RGO composite electrode.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Studies on synthesis of reduced graphene oxide (RGO) via green route and its electrical property

Highlights: • RGO-1 and RGO-2 were synthesized by green method using different phytoextracts. • M. indica L., S. tuberosum L. phytoextracts act as reducing and stabilizing agents. • Conjugated structure of graphene is established following partial reduction of GO. • Electrical conductivities of RGO-1 and RGO-2 are higher than GO. - Abstract: An environmentally friendly method has been applied for the preparation of reduced graphene oxide (RGO). This method was developed by using polyphenols that contained a phytoextract of Mangifera indica L. along with Solanum tuberosum L. as reducing agents since they are non-toxic and naturally available. The phytoextracts used in the production of RGO was set between 60 and 70 °C. Graphene oxide (GO) was prepared by modified Hummer’s method as reported in earlier findings. Structural and morphological studies demonstrate that the part of the oxygen functionalities in GO can be removed by following green reduction. Characterizations of the resulting product have been done by X-ray diffraction, FTIR, UV–vis and Raman spectroscopy. FESEM, TEM, EDX spectrum, TGA, DLS and Zeta potential measurements of the samples have also been carried out to study the morphological, thermal and surface charge characteristics. Electrical conductivity was also measured to check the extent of reduction of GO to RGO.

36 MATERIALS SCIENCE↗

Structural and optical characterizations of Cu2SnS3 (CTS) nanoparticles synthesized by one-step green hydrothermal route

Highlights: • Pure quasi-stoichiometric CTS nanoparticles obtained by green hydrothermal route. • Cubic structure of CTS nanoparticles without secondary phases was acheived. • A formation mechanism of the CTS nanoparticles is proposed. • CTS has a band gap of Eg = 1.4 eV, which is optimal for photovoltaïc absorber. - Abstract: In this study, nanoparticles of Cu{sub 2}SnS{sub 3} (CTS) have been synthesized by a simple one-step hydrothermal route without annealing. Metal chlorides and sodium sulphide precursors were dissolved in green solvent (water) and maintained at 230 °C for 24 h in a laboratory scale autoclave. Structural, morphological and optical characterization of synthesized CTS nanoparticles has been performed by Energy Dispersive Spectrometry (EDS), X-Ray Diffraction (XRD), Raman Spectroscopy, Field Emission Scanning Electron Microscopy (FESEM), Transmission Electron Microscopy (TEM) and UV–vis-NIR Spectroscopy. The results appear to confirm the formation of pure and quasi-stoichiometric cubic CTS nanoparticles. No secondary phases have been detected. The average size of the synthesized nanoparticles is estimated to be about 30 nm. From the absorption measurements, the optical band gap energy of the CTS nanoparticles was estimated to be 1.4 eV. This is very close to the optimal value required for an absorber material in photovoltaic (PV) solar energy conversion. In order to improve the understanding of the formation mechanism of CTS nanoparticles, the precipitate recovered prior to the hydrothermal reaction was analysed by EDS and XRD. The obtained results suggest that the formation of CTS nanoparticles takes place in two stages. Firstly, it is initiated from the formation of precipitates of Cu{sub 2}S, CuS and SnS binary compounds in the starting precursors solution prior to the hydrothermal reaction and thereafter it is completed under hydrothermal conditions. This study shows the feasibility of synthesizing CTS nanoparticles with abundant elements using an environmentally-friendly and low cost process.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effective photocatalytic removal of different dye stuffs using green synthesized zinc oxide nanogranules

Highlights: • Zinc oxide nanoparticles (ZnO-NPs) synthesized by a green strategy using lemon juice and ethylene glycol. • Physicochemical studies confess the formation of hexagonal wurtzite ZnO nanaogranules with some honed faces. • Direct band gap energy obtained for ZnO nano granules was 3.15 eV. • ZnO nano granules act as good catalyst for the photo degradation of methylene blue, congo red, and rhodamine B under UV-light irradiation. - Abstract: Zinc oxide nanoparticles (ZnO-NPs) obtained by a green synthetic strategy using lemon juice and ethylene glycol. The material was characterized using the techniques UV–vis spectroscopy, FTIR spectroscopy, X-ray diffraction analysis, FESEM, EDAX and HRTEM. Diffraction patterns and TEM micrographs confess the formation of hexagonal wurtzite ZnO nanaogranules with some honed faces and having an average size of 49.16 nm. The developed ZnO-NPs was tested for the photocatalytic degradation of Methylene Blue, Congo Red and Rhodamine B target dyes under UV irradiation and found to have remarkable activity.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Synthesis and luminescent properties of Er3+-activated LaBMoO6 green-emitting phosphors for optical thermometry

Highlights: • Under 380 nm excitation, all the samples emitted visible green emissions from the Er{sup 3+} ions. • The optimal doping concentration was 1 mol% and the critical distance was 28.47 Å. • The maximum sensor sensitivity of the studied phosphors was found to be as high as 0.0179 K{sup −1} at 483 K. • The sensor sensitivity of the obtained samples was independent of Er{sup 3+} ion concentration. - Abstract: The Er{sup 3+}-activated LaBMoO{sub 6} phosphors were synthesized by a sol-gel method. The photoluminescence (PL) emission intensity was revealed to be dependent on the Er{sup 3+} ion concentration and its maximum value was achieved when the doping concentration was 1 mol%. From theoretical analysis, one knows that the concentration quenching mechanism is dominated by the electric dipole-dipole interaction with a critical distance of 28.47 Å. On the basis of the temperature-dependent PL green emission spectra from the {sup 2}H{sub 11/2} and {sup 4}S{sub 3/2} thermally coupled levels by means of the fluorescence intensity ratio technique, the temperature sensing properties of the resultant compounds were studied. When the temperature was 483 K, the sensor sensitivity of the studied samples reached up to 0.017 K{sup −1}. It was found that the sensor sensitivity of the prepared phosphors was hardly varied by the doping concentration. These obtained characteristics suggest that the Er{sup 3+}-activated LaBMoO{sub 6} phosphors have potential applications in optical thermometry.

36 MATERIALS SCIENCE↗

Green synthesis of N, S co-doped carbon quantum dots from triflic acid treated palm shell waste and their application in nitrophenol sensing

Highlights: • Novel Triflic Acid Treated Palm Shell based Carbon Quantum Dots were fabricated. • The fabrication process is green and sustainable. • The quantum dots exhibited greenish fluorescence. • CQDs were used as fluorescence probe for nitrophenols with good detection limits. - Abstract: Herein, we report N and S co-doped Carbon quantum dots (CQDs) prepared using palm shell powder (PSP) and triflic acid. The CQDs possessed a graphitic-like structure with narrow size distribution and exhibited a bright green fluorescence. The fluorescent property of CQDs was found to be independent of the excitation wavelength and was used as fluorescence probe for nitrophenols (NPs) with good detection limits (0.079 μM, 0.165 μM, 0.082 μM for NP, DNP and TNP respectively) and linearity in the range 0.2–0.40 μM, 0.5–85 μM, 0.20–40 μM for NP, DNP and TNP respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Quinolyl functionalized spiro[fluorene-9,9'-xanthene] host materials with bipolar characteristics for green and red phosphorescent organic light-emitting diodes

Spiro[fluorene-9,9'-xanthene] (SFX) bipolar hosts bearing one, two and three quinolyl substituents, namely SFX-bPy, SFX-DbPy and SFX-TbPy, were designed and synthesized for phosphorescent organic light emitting diodes (PhOLEDs). The successive substitution of quinoline at 2', 2 and 7' positions of SFX results in reduced LUMO energy levels while leaving the HOMO energy levels nearly intact. The impact of quinoline substitution in these SFX-based hosts on PhOLED performance was investigated in detail through green and red model devices. For the green emitting devices, the device based on SFX-bPy host showed better performance (23.6 cd A -1 , 23.4 lm W -1 , 6.3%) due to high triplet energy level ( T 1 ) and balanced carriers-transporting ability. In contrast, for the red PhOLED devices, the device hosted by SFX-DbPy displayed higher performance (15.8 cd A -1 , 16.0 lm W -1 , 9.1%), attributable to the well matched T 1 and separated frontier molecular orbitals. This work thus sheds light on the rational design of SFX-based bipolar hosts for more efficient PhOLEDs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multi-scale integration of satellite remote sensing improves characterization of dry-season green-up in an Amazon tropical evergreen forest

In tropical forests, leaf phenology-particularly the pronounced dry-season green-up-strongly regulates biogeochemical cycles of carbon and water fluxes. However, uncertainties remain in the understanding of tropical forest leaf phenology at different spatial scales. Phenocams accurately characterize leaf phenology at the crown and ecosystem scales but are limited to a few sites and time spans of a few years. Time-series satellite observations might fill this gap, but the commonly used satellites (e.g. MODIS, Landsat and Sentinel-2) have resolutions too coarse to characterize single crowns. To resolve this observational challenge, we used the PlanetScope constellation with a 3m resolution and near daily nadir-view coverage. We first developed a rigorous method to cross-calibrate PlanetScope surface reflectance using daily BRDF-adjusted MODIS as the reference. We then used linear spectral unmixing of calibrated PlanetScope to obtain dry-season change in the fractional cover of green vegetation (GV) and non-photosynthetic vegetation (NPV) at the PlanetScope pixel level. We used the Central Amazon Tapajos National Forest k67 site, as all necessary data (from field to phenocam and satellite observations) was available. For this proof of concept, we chose a set of 22 dates of PlanetScope measurements in 2018 and 16 in 2019, all from the six drier months of the year to provide the highest possible cloud-free temporal resolution. Our results show that MODIS-calibrated dry-season PlanetScope data (1) accurately assessed seasonal changes in ecosystem-scale and crown-scale spectral reflectance; (2) detected an increase in ecosystem-scale GV fraction (and a decrease in NPV fraction) from June to November of both years, consistent with local phenocam observations with R 2 around 0.8; and (3) monitored large seasonal trend variability in crown-scale NPV fraction. Finally, our results highlight the potential of integrating multi-scale satellite observations to extend fine-scale leaf phenology monitoring beyond the spatial limits of phenocams.

54 ENVIRONMENTAL SCIENCES↗

A country-scale green energy-water-hydrogen nexus: Jordan as a case study

Many developing countries suffer from a shortage of clean energy-water production, causing significant dependency on imported fossil fuel to meet the local energy and freshwater demands. Furthermore, when planning a 100 % renewable energy system (RES) to match the energy demand on an hourly basis, the RES is usually oversized. Hence, unavoidable large amounts of excess energy would be generated during hours of high production, low demand, and fully charged energy storage systems (ESSs). Hence, using Jordan as a case study, this work proposes a novel integrated system of wind, solar photovoltaic (PV), and lithium-ion ESS to match 100 % of the country's energy demand while using the excess generated power to drive reverse osmosis water desalination plants to match the demand of freshwater as well. Furthermore, the remaining excess energy is used for producing green hydrogen. A techno-economic optimizer was developed to show that this concept is indeed feasible. Here, the model was used to scan Jordan for the fitting sites of the highest demand-supply matching and the lowest levelized cost of electricity (LCOE), simultaneously. Three different integration scenarios are presented, namely PV-ESS, wind-ESS, and hybrid PV-wind-ESS RESs. The hybrid system showed the best performance, especially compared to the wind-ESS RES, in terms of total installed capacity (33.37 GW), LCOE (0.0492 USD/kWh), specific water cost (0.3629 USD/m 3 ), and energy and water demand-supply fractions (99.47 and 96.16 %, respectively). Storing desalinated water in natural aquifers was found to be a favorable option to enhance the performance of the three systems, where stored water by the end of the year was sufficient to cover the freshwater requirements for several following years. Finally, the remaining excess energy is used to produce green hydrogen with an annual production of up to 1.37 million tons and a specific cost down to 1.08 USD/kg.

14 SOLAR ENERGY↗

Co-composting of green waste and food waste at low C/N ratio

In this study, co-composting of food waste and green waste at low initial carbon to nitrogen (C/N) ratios was investigated using an in-vessel lab-scale composting reactor. The central composite design (CCD) and response surface method (RSM) were applied to obtain the optimal operating conditions over a range of preselected moisture contents (45-75%) and C/N ratios (13.9-19.6). The results indicate that the optimal moisture content for co-composting of food waste and green waste is 60%, and the substrate at a C/N ratio of 19.6 can be decomposed effectively to reduce 33% of total volatile solids (TVS) in 12 days. The TVS reduction can be modeled by using a second-order equation with a good fit. In addition, the compost passes the standard germination index of white radish seed indicating that it can be used as soil amendment.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗