Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fissionable Material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Measurement of the Neutron-Induced Capture-to-Fission Cross Section Ratio in 233 U at LANSCE [Slides]

This presentation finds that new measurement at LANSCE combining DANCE and NEUANCE at the end of 2020 and 2021. Additionally, two samples of 10 mg and 20 mg of 233 U have been prepared at LANL by Evelyn M. Bond (December 2020). Data analysis has been finished and results of the capture-to-fission ratio on 233 U in the neutron energy region from 0.7 eV to 250 keV have been provided. The focus was to provide data from 1-300 keV. We are providing data from 0.7 eV to 1 keV in addition. The result has been normalized to the ENDF/B-VIII.0 broadened capture-to-fission cross section ratio in the neutron energy region recommended by the Luiz Leal and Marco Pigni, between 8.1 and 14.7 eV. This is the first measurement of the capture-to-fission ratio between 2 - 30 keV. The data show some small differences in the RRR with the evaluation though the general trend is consistent. In the URR this data shows a smaller capture-to-fission ratio than the evaluation from 10 to 150 keV

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Progress Towards the Reality of Low-Temperature Critical Experiments with Low-Temperature TEX

Integral benchmarks for criticality safety do not exist below room temperature. Incredible support for below room temperature benchmarks is present across the international community. Validation of low-temperature neutron cross sections is necessary to verify any operation at temperatures below room temperature which is typically observed in environments far from the equator. For example, a fissile material transportation truck may routinely observe ambient temperatures down to -40°C, which is the lower temperature bound of the normal conditions of transportation defined in the United States Title 10 Code of Federal Regulations §71.71c2. Similarly, the IAEA, which contains 176 member states, has the same requirement for subcriticality for fissile material transportation. Additionally, sub-room temperature benchmarks can validate newly produced cross sections, that include novel thermal scattering laws, from North Carolina State University. A six-case experiment designed based off the TEX-HEU baseline experiments has been proposed utilizing a chilled vacuum chamber capable of cooling the HEU stack down to -50°C. The six proposed configurations span the entire neutron fission energy range and can be tested at intermediate temperatures between room temperature and -40°C. Of the six configurations, the fastest case utilizes nearly 135 kg of HEU. Understanding the system is required prior to critical experiment operations. In order to test the functionality of the system, testing with surrogate fuel materials has been conducted. The following discusses the design of the low temperature TEX (LT-TEX) experiment as well as the progress made via surrogate testing towards a reality in which low-temperature integral benchmarks exist in the International Criticality Safety Benchmark Evaluation Project (ICSBEP).

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Performance and properties evolution of near-term accident tolerant fuel: Cr-doped UO 2

Chromium-doped UO 2 fuel has received significant interest due to the ability for chromium to produce pellets with large average grain size (>30 μm), which has shown to increase fission gas retention during operation. Sintering of chromium-doped UO 2 pellets was pursued with oxygen potential and sintering atmosphere controlled to tailor the final microstructure of the material. Chromium additions in this study ranged from 750 to 7800 ppm. Cr concentrations were studied pre and post sintering using Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). Effects of chromium content on lattice parameter and microstructure were examined with X-ray diffraction (XRD) and scanning electron microscopy (SEM). Contraction of the UO 2 lattice parameter was observed, as well as enlargement of grain size with increasing chromium content up to 4900 ppm Cr 2 O 3 . In addition, SEM indicated Cr incorporation within the matrix and the formation of chromium oxide precipitates throughout the microstructure at high Cr concentrations. Evaluation of thermophysical properties of Cr-doped UO 2 pellets were conducted up to 1200 °C to illustrate their evolution with increased dopant concentration and microstructural changes. The results show that grain size is maximized at 52 μm with Cr 2 O 3 concentration equal to 4900 ppm; however, grain size decreases at higher Cr 2 O 3 concentrations. No significant changes were observed in specific heat capacity, linear thermal expansion, and coefficient of thermal expansion compared to undoped UO 2 . The thermal conductivity also decreased through the incorporation of Cr 2 O 3 dopants above 750 ppm and is shown to be ~15 % lower than reported UO 2 values.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Singlet fission

Singlet fission (SF) is a process whereby a photo-excited singlet exciton spontaneously splits into lower energy triplet excitons. This process has been known to occur in select organic materials for over 50 years but in the past was viewed as a curiosity and not as a problem worthy of focused attention. Over the past decade, this viewpoint has changed as the promising use of SF to improve photovoltaic efficiency has spurred vast activity, which has revealed the richness of the phenomenon. Currently, our understanding of the role played by various bright and dark states and their couplings to vibrations and to each other and by chemical composition and packing, among other factors, has enabled a large increase in the number of viable SF systems as well as a far deeper understanding of the process itself. These advances have allowed for the demonstration of proof-of-concept increases in the solar cell efficiency via the use of SF materials in simple tandem cells and as sensitizers in conjunction with conventional photovoltaics. Indeed, concepts surrounding the field have now invaded other fields, with a prominent example being the use of photon upconversion associated with triplet–triplet fusion (the inverse process to SF) in organic chemistry and photocatalysis. The 23 research articles in this special topic showcase recent cutting-edge advances in the field and highlight the diverse new directions being explored in the field of SF.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Efficient Failure Probability Calculations and Modeling Interface Debonding in TRISO Particles with BISON

This document constitutes completion of the NEAMS milestone, which is titled Demonstrate efficiency improvements in TRISO failure probability calculations and the effect of debonding on fission product transport in TRISO fuel particles in Bison . In this report we present the development of the following: (1) the anisotropic elasticity model of pyrolytic carbon and extended material models using the local coordinate system for aspherical particle geometry; (2) a capability of modeling interface debonding in TRISO particles; and (3) an efficient high-fidelity approach to calculate the failure probability of TRISO particles. Benchmark problems and AGR-2 tests are used to verify the models and demonstrate these new capabilities.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Role of Accelerated Burnup Irradiation Testing in Support of Accelerated Fuel Qualification

Accelerated fuel qualification has gained attention as a means to reduce the time needed to realize new nuclear fuel concepts and expand the operating windows of existing fuel forms. A key component of this approach is accelerated burnup irradiation testing. Although the concept of accelerated burnup has been familiar to the community for many decades, the specifics about how the increasing fission rate may be used as a qualification tool have not yet been elucidated. The present work provides a vision of how accelerated fission rate testing can enable accelerated fuel qualification. Technology readiness levels (TRLs) are reintroduced to demarcate the stages of traditional fuel qualification, and accelerated fuel qualification is presented in this context. The critical steps needed to achieve each TRL are reframed within the context of modern nuclear materials research and development, as revolutionary fuel concepts are more common than previous eras. The practical impacts of accelerated fuel qualification approaches as applied to contemporary fuel qualification efforts are illustrated. Examples are given to illustrate how accelerated burnup irradiations are being used currently and could be applied in the future to support qualification and licensure. Finally, outstanding challenges in the application of accelerated burnup methods to nuclear fuel qualification are summarized, with priority placed on understanding how fission rate impacts diffusion, microstructure evolution, and other critical mechanisms that dictate fuel performance.

Accelerated fuel qualification↗
DOE OSTI2025

Mechanistic nuclear fuel performance modeling of uranium nitride

Uranium mononitride (UN) is a nuclear fuel candidate for advanced reactor designs and an alternative being considered for light water reactors due to its higher thermal conductivity and uranium density than UO 2 . As with any nuclear fuel, swelling and fission gas release are important factors for safety, while also being some of the hardest phenomena to predict with a high degree of confidence. Getting a grasp on the gas swelling behavior and release is crucial to lower the barrier for UN utilization. An accelerated swelling rate at high temperatures observed experimentally, sometimes referred to as “breakaway swelling,” further complicates the prediction of fuel performance of UN. A mechanistic model has been developed using a multiscale approach to describe the intragranular and intergranular fission gas behavior. Lower-length-scale calculations have been employed to inform models of the gas and self-diffusion behavior, resolution rate, and bubble shape. Leveraging previous work on high burnup UO 2 , two populations of intragranular bubbles are considered; small bulk bubbles and larger bubbles located along dislocations. The dislocation bubbles were found to be crucial to the overall swelling behavior, and the breakaway swelling transition was associated with the transition in the gas atom diffusion mechanism from an irradiation-induced athermal diffusion regime at lower temperatures to an intrinsic thermal equilibrium regime at higher temperatures, accelerating the growth of the dislocation bubbles. Similarly, the threshold for fission gas release was associated with the grain boundary vacancy diffusivity surpassing the gas atom diffusivity at sufficiently high temperatures, allowing the over-pressurized grain boundary bubble to grow in size and interconnect. Using thermo-mechanical models with the fission gas model, two integral fuel pin assessment cases were simulated. Finally, this work demonstrates the ability of a multiscale approach to accelerate the understanding of advanced fuel forms when experimental data is limited.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Computational Thermal Hydraulics of a High-Performance Low-Enriched-Uranium Annular Target for HFIR Irradiation

Molybdenum-99 has historically been generated via isolation from fissioned highly enriched uranium (HEU) targets. Here, this isotope is in high demand due to its daily use across the world in radiopharmaceutical medical procedures. The primary objective of this work was to design and analyze an experimental target assembly containing one low-enriched-uranium (LEU) annular target for irradiation at the High Flux Isotope Reactor (HFIR). Efforts included incorporating spatially dependent energy sources from neutron and gamma interactions, quantifying thermal contact conductance at material interfaces, performing grid-independent studies, comparing turbulence models, and simulating various steady-state and transient scenarios relevant for irradiation qualification and eventual insertion. These models provide velocity, pressure, and temperature distributions in both space and time. Such results enable the selection of an appropriate irradiation location, fission rate density, and flow-limiting orifice size and demonstrate compliance with HFIR safety requirements such that insertion into the reactor can be approved. This analysis shows that across all scenarios, wetted surface temperatures remain below the coolant saturation temperature with no net vapor formation in the coolant. In every scenario, all components stay below 30% of the aluminum 6061 melting temperature. Computational fluid dynamics and system-level models predict peak target temperatures that agree within 4%, though the predicted axial location of the peak differs by about 10% of the heated length due to differences in flow development length. These results de-risk the irradiation of LEU (annular targets) and strengthen a domestic, HEU-independent 99 Mo supply by providing important fuel performance data to form the foundation for a robust licensing basis.

Molybdenum-99↗
DOE OSTI2023

Sister Rod Destructive Examinations (FY22) Appendix C: Rod Internal Pressure, Void Volume, and Gas Transmission Tests

As a part of the DOE NE High Burnup Spent Fuel Data Project, Oak Ridge National Laboratory (ORNL) is performing destructive examinations (DEs) of high burnup (HBU) (>45 GWD/MTU) spent nuclear fuel (SNF) rods from the North Anna Nuclear Power Station operated by Dominion Energy [C-1]. The SNF rods, called the sister rods or sibling rods, are all HBU and include four different kinds of fuel rod cladding: standard Zircaloy-4 (Zirc-4), low-tin (LT) Zirc-4, ZIRLO, and M5. The DEs are being conducted to obtain a baseline of the HBU rod’s condition before dry storage and are focused on understanding overall SNF rod strength and durability. Both fuel rods and empty cladding will be tested to derive material properties. Although the data generated can be used for multiple purposes, one primary goal for obtaining the postirradiation examination data and the associated measured mechanical properties is to support SNF dry storage licensing and relicensing activities by (1) addressing identified knowledge gaps and (2) enhancing the technical basis for post-storage transportation, handling, and consolidation activities. This appendix documents the status of the ORNL Phase 1 DE activities [C-2, C-3] related to rod internal pressure and void volume measurement techniques, fission gas stack flow measurements applied to selected sister rods, and fission gas release calculations in Phase 1 of the sister rod test program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Sister Rod Destructive Examinations (FY23) Appendix C: Rod Internal Pressure, Void Volume, and Gas Transmission Tests

As a part of the DOE NE High Burnup Spent Fuel Data Project, Oak Ridge National Laboratory (ORNL) is performing destructive examinations (DEs) of high burnup (HBU) (>45 GWD/MTU) spent nuclear fuel (SNF) rods from the North Anna Nuclear Power Station operated by Dominion Energy. The SNF rods, called the sister rods or sibling rods, are all HBU and include four different kinds of fuel rod cladding: standard Zircaloy-4 (Zirc-4), low-tin (LT) Zirc-4, ZIRLO, and M5. The DEs are being conducted to obtain a baseline of the HBU rod’s condition before dry storage and are focused on understanding overall SNF rod strength and durability. Both fuel rods and empty cladding will be tested to derive material properties. Although the data generated can be used for multiple purposes, one primary goal for obtaining the postirradiation examination data and the associated measured mechanical properties is to support SNF dry storage licensing and relicensing activities by (1) addressing identified knowledge gaps and (2) enhancing the technical basis for post-storage transportation, handling, and consolidation activities. This appendix documents the status of the ORNL Phase 1 DE activities related to rod internal pressure and void volume measurement techniques, fission gas stack flow measurements applied to selected sister rods, and fission gas release calculations in Phase 1 of the sister rod test program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Recent Advances in Radiation-Induced Actinide Redox Chemistry

The actinide series boasts many unique physical and chemical features worthy of both fundamental and applied study. However, the chemical influence of their inherent radiation field is often overlooked, especially as we begin to explore the late actinides in more detail than ever possible before. From the perspective of used nuclear fuel reprocessing, the absorption of ionizing radiation induces the formation of a variety of transient and steady-state excited states, radicals, ions, and molecular degradation products, many of which are highly redox active and can lead to significant changes in a reprocessing solvent system’s physical and chemical properties. For example, radiolysis of the actinides can drive steady-state redox distributions and the formation of non-traditional oxidation states which can complicate their separation and recovery from fission products. This scenario is further exacerbated when complexation is taken into account. Consequently, a molecular-level understanding of radiation effects on the actinides over multiple time, distance, and material domains is essential for supporting innovation in used nuclear fuel reprocessing technologies. Attaining this knowledge necessitates a firm grasp of actinide radiation chemistry to develop predictive, mechanistic, multiscale models to support engineering efforts. Presented here are several recent studies that highlight recent advances in actinide radiation chemistry, in particular, the effect of actinide complexation on ligand reactivity towards radiation-induced transients.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2024

Fuel Performance Modeling Status Update and Potential Model Improvements

Fuel performance modeling status update and potential model improvements overview of TRISO fuel performance modeling codes PARFUME/BISON, AGR experiment support, potential modeling improvements, BISON smeared cracking model, BISON fission product source term, and AGR-3/4 reirradiation heating test.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

AGC-4 As-Run Uncertainty Analysis

The concept of measuring neutron flux (or fluence rate) with activation foils has existed since the late 1940s and is a well-used methodology. Activation foils are selected for their unique isotopic cross sections that create reaction products with desirable properties: relatively simple radioactive decay scheme, measurable quantities of gamma-rays or betas, and half-lives appropriate for the irradiation and decay durations of the experiment. The activation materials, deemed flux wires, fluence wires, dosimeters, or flux foils, are fabricated to have a mass appropriate for the irradiation as well so the measurement using a radiation detector following the irradiation is sufficient but not overwhelming in terms of total activity. Activation measurement results are expressed in terms of reaction rate, which can then be used to “adjust” the neutron spectrum. The Advanced Graphite Creep (AGC)-4 experiment contained 26 flux wire packages, each containing an iron and a niobium wire inside a vanadium capsule. For all stackup positions, the value of fast to thermal neutrons is higher than expected, but the total neutron fluence is near the predicted value of ~2 x 1022 n/cm2. As compared to the predicted neutron spectrum, there are four takeaways in the results as compared to the predicted ATR irradiation: 1) Additional fast (fission) neutrons present, 2) Spectrum hardening due to temperature, 3) Spectrum hardening due to container attenuation, 4) Total neutron fluence is close to predicted values. Since the neutron energy spectrum is a key parameter when attributing neutron damage in materials, the adjusted energy-dependent spectrum and the total neutron fluence results from the dosimeters can be incorporated for future calculations.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Analysis and Thermal Property Investigations into Ternary Actinide Chloride Salt Systems Containing UCl3 and PuCl3

While regulators, the scientific community, and MSR developers still lack access to literature data on the thermal properties of clean fuel salts, even less information is available on the properties of fuel salts containing impurities. It is essential to understand, benchmark, and predict crucial data on the changes in thermal properties of fuel salt systems due to impurities arising from moisture, corrosion, and reactor operation (i.e., fission products). This research focuses on two actinide fuel salts (1) to investigate a worst-case scenario buildup of actinide fission product in a NaCl-UCl3 eutectic fuel salt and (2) to investigate NaCl-PuCl3 eutectic salt after 1000 hours of operation in a natural circulation flow loop flow to determine if corrosion or atmospheric (moisture/oxygen) products are present. For the first salt, a conservative assumption or worst-case scenario, for fission product buildup in a fuel salt was investigated by adding PuCl3 to eutectic 67 mol% NaCl – 33 mol% UCl3 salt resulting in a ternary salt having a composition of 61 mol% NaCl – 30 mol% UCl3 – 9mol% PuCl3. Addition of PuCl3 to eutectic NaCl-UCl3 resulted in a ternary salt that had a higher melting temperature than either the NaCl-PuCl3 or NaCl-UCl3 binary eutectic mixture. Addition of PuCl3 also resulted in an increase in density which was expected. The second salt was extracted from a micro loop. The composition of the fuel (primary) salt prior to flow loop operations was determined to be 64 mol% NaCl – 36 mol% PuCl3, however, the post-flow loop salt showed increased levels of MgCl2 and NaCl changing the salt composition to 10 mol% MgCl2 – 63mol% NaCl – 26mol% PuCl3) indicating the primary salt interacted with the rinse salt. Analysis of the post flow loop salt detected low concentrations of Al, Ni, Co, Nb, and Zr, most likely corrosion products from the flow loop material of construction. Contamination of the fuel salt (with the rinse salt NaCl-MgCl2) decreased the density by approximately 10% and reduced the onset of melting temperature by 50 °C, from 451 °C to approximately 400 °C. Results from the fission product simulated salt (61 mol% NaCl – 30 mol% UCl3 – 9mol% PuCl3) and the corrosion product salt (10 mol% MgCl2 – 63mol% NaCl – 26mol% PuCl3) will be included in two separate manuscripts for submission to peer-reviewed journals.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Exploring competitive metal binding and crystallization of UO 2 2+ and Cu 2+ tetrahydrofuran-2,3,4,5-tetracarboxylic acid complexes

Solvent extractions are used to separate actinide elements from fission products in nuclear waste streams and the successful isolation of specific species utilize subtle differences in metal ligand binding. Metal ligand binding is also important in crystallization of metal organic materials and herein we explore the importance of competitive binding in the tetrahydrofuran-2,3,4,5-tetracarboxylic acid (THFTCA) system. This ligand has been previously evaluated for the selective extraction of uranium from other lanthanides and actinides and in the current research, we evaluate the crystallization of uranyl-THFTCA complexes in the presence of Cu 2+ , Sr 2+ , Th 4+ , and Ce 3+ . Three major phases were formed in the crystallization experiments and characterized with single crystal X-ray diffraction, powder X-ray diffraction, thermogravimetric analysis, and Raman spectroscopy. Two of the resulting phases were novel (UTHF1 ((C 4 H 10 N 2 )[UO 2 (C 8 H 8 O 9 ) 2 ]∙2H 2 O) and UTHF2 (Na[(UO 2 )(C 8 H 5 O 9 )(H 2 O)]∙ 3.5 H 2 O)), whereas the third (CuTHF1) was previously reported in the literature. Raman spectroscopy was utilized to evaluate spectral changes in the mother liquor of UTHF1, UTHF2, and CuTHF1 over time to assess the crystallization process. Further, isothermal titration calorimetry was used to determine the binding constants for UO 2 2+ and Cu 2+ to the THFTCA ligand in solution and evaluate the role of competitive metal binding in this system. The thermodynamic parameters and the crystallographic data were used to justify the formation of a weaker UO 2 2+ -THFTCA complex. Formation of a weaker UO 2 2+ -THFTCA complex supports our findings that UTHF1 only forms in homomeric systems, but suggests that the crystallization of UTHF2 and CuTHF1 is reliant on the presence of additional counter ions and ligands to change the amount of available THFTCA ligand.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Status of Mechanistic Fission Gas Model in High-Burnup Fuel

A desire to increase fuel burnup to decrease the cost of nuclear power plants has led to significant interest within the nuclear industry to develop improved understanding of high-burnup nuclear fuel microstructure and the potential for fuel fragmentation, relocation, and dispersal that contribute to burnup and safe operating limits. This milestone report describes joint research activities and program planning to develop mechanistic models for high-burnup UO 2 microstructure, including both intra- and intergranular gas bubble populations and fission gas release, specifically associated with transient release. This model development is being extensively leveraged against a rapidly growing experimental database of high-fidelity electron microscopy characterization of commercial, light water reactor fuel in the as-irradiated condition as well as that following simulated loss-of-coolant test conditions. This report describes the status of model development, highlights recent microstructural data, and summarizes the data needs to complete initial development and experimental validation of mechanistic models of fission gas and microstructural evolution at high burnup, as well as transient fission gas release.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Technical Program Plan for INL Advanced Reactor Technologies Advanced Gas Reactor Fuel Development and Qualification Program

High-temperature gas cooled reactors (HTGRs) are graphite moderated nuclear reactors cooled with helium. Their high outlet temperatures and thermal energy conversion efficiency enable efficient and cost effective integration with non electricity generating applications. These applications include process heat and hydrogen production for petrochemical and other industrial processes that require operating temperatures between 300 and 900°C. HTGRs will supplement the use of premium fossil fuels such as oil and natural gas, improve overall energy security in the United States by reducing dependence on foreign fuels, and reduce carbon dioxide (CO2)/greenhouse gas emissions. The HTGR design uses helium as a coolant, graphite as a neutron moderator, and ceramic particle fuel. Helium is chemically inert and neutronically transparent. The graphite core slows down the neutrons, retains its strength at high temperatures, provides structural stability, and acts as a substantial heat sink during transient conditions. The ceramic particle fuel is extremely robust and retains the radioactive by products of the fission reaction within the coated particle under normal and off normal conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Technical Program Plan for INL Advanced Reactor Technologies Advanced Gas Reactor Fuel Development and Qualification Program

High-temperature gas cooled reactors (HTGRs) are graphite moderated nuclear reactors cooled with helium. Their high outlet temperatures and thermal energy conversion efficiency enable efficient and cost effective integration with non electricity generating applications. These applications include process heat and hydrogen production for petrochemical and other industrial processes that require operating temperatures between 300 and 900°C. HTGRs will supplement the use of premium fossil fuels such as oil and natural gas, improve overall energy security in the United States by reducing dependence on foreign fuels, and reduce carbon dioxide (CO2)/greenhouse gas emissions. The HTGR design uses helium as a coolant, graphite as a neutron moderator, and ceramic particle fuel. Helium is chemically inert and neutronically transparent. The graphite core slows down the neutrons, retains its strength at high temperatures, provides structural stability, and acts as a substantial heat sink during transient conditions. The ceramic particle fuel is extremely robust and retains the radioactive by products of the fission reaction within the coated particle under normal and off normal conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗