Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamic stiffness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Modal and Impact Dynamics Analysis of an Aluminum Cylinder

This paper presents analyses for the modal characteristics and impact response of an all-aluminum cylinder. The analyses were performed in preparation for impact tests of the cylinder at The Impact Dynamics Research Facility (IDRF) at the NASA Langley Research Center. Mode shapes and frequencies were computed using NASTRAN and compared with existing experimental data to assess the overall accuracy of the mass and stiffness of the finite element model. A series of non-linear impact analyses were then performed using MSC Dytran in which the weight distribution on the floor and the impact velocity of the cylinder were varied. The effects of impact velocity and mass on the rebound and gross deformation of the cylinder were studied in this investigation.

Lessard, Wendy B.↗
NASA NTRS1961

Supersonic Panel Flutter Test Results for Flat Fiber-Glass Sandwich Panels with Foamed Cores

Flutter tests have been made on flat panels having a 1/4 inch-thick plastic-foam core covered with thin fiber-glass laminates. The testing was done in the Langley Unitary Plan wind tunnel at Mach numbers from 1.76 t o 2.87. The flutter boundary for these panels was found to be near the flutter boundary of thin metal panels when compared on the basis of an equivalent panel stiffness. The results also demonstrated that the depth of the cavity behind the panel has a pronounced influence on flutter. Changing the cavity depth from 1 1/2 inches to 1/2 inch reduced the dynamic pressure at start of flutter by 40 percent. No flutter was obtained when the spacers on the back of the panel were against the bottom of the cavity.

Tuovila, W. J.↗
NASA NTRS2010

Investigation of a Macromechanical Approach to Analyzing Triaxially-Braided Polymer Composites

A macro level finite element-based model has been developed to simulate the mechanical and impact response of triaxially-braided polymer matrix composites. In the analytical model, the triaxial braid architecture is simulated by using four parallel shell elements, each of which is modeled as a laminated composite. The commercial transient dynamic finite element code LS-DYNA is used to conduct the simulations, and a continuum damage mechanics model internal to LS-DYNA is used as the material constitutive model. The material stiffness and strength values required for the constitutive model are determined based on coupon level tests on the braided composite. Simulations of quasi-static coupon tests of a representative braided composite are conducted. Varying the strength values that are input to the material model is found to have a significant influence on the effective material response predicted by the finite element analysis, sometimes in ways that at first glance appear non-intuitive. A parametric study involving the input strength parameters provides guidance on how the analysis model can be improved.

Goldberg, Robert K.↗
NASA NTRS1989

Low-order design and high-order simulation of active closed-loop control for aerospace structures under construction

Partially constructed/assembled structures in space are complicated enough but their dynamics will also be operating in closed-loop with feedback controllers. The dynamics of such structures are modeled by large-scale finite element models. The model dimension L is extremely large (approximately 10,000) while the numbers of actuators (M) and sensors (P) are small. The model parameters M(sub m) mass matrix, D(sub o) damping matrix, and K(sub o) stiffness matrix, are all symmetric and sparse (banded). Thus simulation of open-loop structure models of very large dimension can be accomplished by special integration techniques for sparse matrices. The problem of simulation of closed-loop control of such structures is complicated by the addition of controllers. Simulation of closed-loop controlled structures is an essential part of the controller design and evaluation process. Current research in the following areas is presented: high-order simulation of actively controlled aerospace structures; low-order controller design and SCI compensation for unmodeled dynamics; prediction of closed-loop stability using asymptotic eigenvalue series; and flexible robot manipulator control experiment.

Balas, Mark J.↗
NASA NTRS1983

Structural design for dynamic response reduction

A computer program for redesigning structural modes to reduce response has been initiated. The linear regulator approach in modal coordinates has been implemented. It is noted that the transformation of solution to physical structure is a major problem. It is concluded that the solution of stiffness equations and damping equations can be done separately as NXN set of (matrix Riccati) equations.

Hanks, B. R.↗
NASA NTRS1974

Theory and comparison with tests of two full-scale proprotors

A nine-degrees-of-freedom theoretical model has been developed for investigations of the dynamics of a prop rotor operating in high inflow axial flight on a cantilever wing. The theory is described, and the results of the analysis are presented for two prop rotor configurations: a gimbaled, stiff in-plane rotor, and a hingeless, soft in-plane rotor. The influence of various elements of the theory is discussed, including the modeling used for the blade and wing aerodynamics and the influence of the rotor lag degree of freedom. The results from full-scale tests of these two prop rotors are presented and compared with the theoretical results.

Johnson, W.↗
NASA NTRS1991

Flexible body dynamic stability for high performance aircraft

Dynamic equations which include the effects of unsteady aerodynamic forces and a flexible body structure were developed for a free flying high performance fighter aircraft. The linear and angular deformations are assumed to be small in the body reference frame, allowing the equations to be linearized in the deformation variables. Equations for total body dynamics and flexible body dynamics are formulated using the hybrid coordinate method and integrated in a state space format. A detailed finite element model of a generic high performance fighter aircraft is used to generate the mass and stiffness matrices. Unsteady aerodynamics are represented by a rational function approximation of the doublet lattice matrices. The equations simplify for the case of constant angular rate of the body reference frame, allowing the effect of roll rate to be studied by computing the eigenvalues of the system. It is found that the rigid body modes of the aircraft are greatly affected by introducing a constant roll rate, while the effect on the flexible modes is minimal for this configuration.

Goforth, E. A.↗
NASA NTRS2012

Macro Scale Independently Homogenized Subcells for Modeling Braided Composites

An analytical method has been developed to analyze the impact response of triaxially braided carbon fiber composites, including the penetration velocity and impact damage patterns. In the analytical model, the triaxial braid architecture is simulated by using four parallel shell elements, each of which is modeled as a laminated composite. Currently, each shell element is considered to be a smeared homogeneous material. The commercial transient dynamic finite element code LS-DYNA is used to conduct the simulations, and a continuum damage mechanics model internal to LS-DYNA is used as the material constitutive model. To determine the stiffness and strength properties required for the constitutive model, a top-down approach for determining the strength properties is merged with a bottom-up approach for determining the stiffness properties. The top-down portion uses global strengths obtained from macro-scale coupon level testing to characterize the material strengths for each subcell. The bottom-up portion uses micro-scale fiber and matrix stiffness properties to characterize the material stiffness for each subcell. Simulations of quasi-static coupon level tests for several representative composites are conducted along with impact simulations.

Blinzler, Brina J.↗
NASA NTRS1995

Effects of Delaminations on the Damped Dynamic Characteristics of Composite Laminates: Mechanics and Experiments

Analytical and experimental work is presented on the damped free-vibration of delaminated laminates and beams. A laminate theory is developed where the unknown kinematic perturbations induced by a delamination crack are treated as additional degrees of freedom. The generalized stiffness, inertia and damping matrices of the laminate are formulated. An analytical solution is developed for the prediction of natural frequencies, modes and modal damping in composite beams with delamination cracks. Evaluations of the mechanics on various cantilever beams with a central delamination are performed. Experimental results for the modal frequencies and damping of composite beams with a single delamination are also presented and correlations between analytical predictions and measured data are shown. The effects of delamination vary based on crack size, laminate configuration, and mode order. The implications of the mechanics in developing delamination detection techniques are also discussed.

Saravanos, D. A.↗
NASA NTRS1971

A study of the flexible body dynamics of the RAE-A satellite

Spacecraft flight data was compared with simulated data computed by the RAE and IMP dynamics simulator computer programs. There was not sufficient data available to provide definitive data on antenna boom position to the Radio Astronomy experimenter. There was, however, enough data to indicate the trend of antenna boom stiffness and temperature gradient. It was possible to obtain a good fit of simulated data to measured spacecraft attitude data when the antenna booms were extended to 450 feet. The value of the RAE-A antenna boom stiffness appears to be significantly less than the preflight ground measured value. It was confirmed that an improved simulation can be obtained by using values of the root angles of the antenna booms and by using an angle of the damper plane of motion, relative to the plane of the antennas, which differed from preflight ground measurements.

Source record↗
NASA NTRS1978

Load and dynamic assessment of B-52B-008 carrier aircraft for finned configuration 1 space shuttle solid rocket booster deceleration subsystem drop test vehicle. Volume 4: Pylon load data

The pylon loading at the drop test vehicle and wing interface attack points is presented. The loads shown are determined using a stiffness method, which assumes the side stiffness of the forward hook guide and the fore and aft stiffness of each drag pin to be equal. The net effect of this assumption is that the forward hook guide reacts approximately 96% of the drop test vehicle yawing moment. For a comparison of these loads to previous X-15 analysis design loadings, see Volume 1 of this document.

Quade, D. A.↗
NASA NTRS1981

Dynamic analysis of a free-tip rotor

The flag-lag-torsion flutter of a constant-lift rotor (CLR) and a free-tip rotor (FTR) has been investigated in hovering flight. The CLR blade consists of a finite number of strips pivotally mounted on the spar; torsional stiffness of the strips is attained through the elastic axis offset from the aerodynamic center. It is shown that, with a suitable combination of lag damper and negative pitch-flap coupling, it is possible to design a CLR blade that is free of aeroelastic instability with suitable airfoil selection. The FTR blade, which consists of an inboard section similar to that of a conventional blade and a small outboard section freely pitching on its spar, is also free of aeroelastic instability.

Chopra, I.↗
NASA NTRS1987

Ground and air resonance of bearingless rotors in hover

A finite element formulation is used to investigate ground and air resistence in hover for a bearingless rotor. Aerodynamic forces are studied using quasi-steady strip theory, and unsteady aerodynamic effects are introduced through an inflow dynamics model. Reasonable correlation was found between predicted ground and air resonance results and data obtained from measurements using a 1/8th Froude-scaled dynamic model. Systematic parametric studies of the effects of various design parameters were performed, and lag frequency was found to significantly influence ground resonance stability, whereas pitch-lag coupling, blade sweep and pitch link stiffness had powerful effects on air resonance stability.

Jang, Jinseok↗
NASA NTRS1988

Extension and validation of a method for locating damaged members in large space trusses

The damage location approach employs the control system capabilities for the structure to test the structure and measure the dynamic response. The measurements are then used in a system identification algorithm to produce a model of the damaged structure. The model is compared to one for the undamaged structure to find regions of reduced stiffness which indicate the location of damage. Kabe's 3,4 stiffness matrix adjustment method was the central identification algorithm. The strength of his method is that, with minimal data, it preserves the representation of the physical connectivity of the structure in the resulting model of the damaged truss. However, extensive storage and computational effort were required as a result. Extension of the damage location method to overcome these problems is the first part of the current work. The central system identification algorithm is replaced with the MSMT method of stiffness matrix adjustment which was previously derived by generalizing an optimal-update secant method form quasi-Newton approaches for nonlinear optimization. Validation of the extended damage location method is the second goal.

Smith, Suzanne Weaver↗
NASA NTRS2010

Modification of a Macromechanical Finite-Element Based Model for Impact Analysis of Triaxially-Braided Composites

A macro level finite element-based model has been developed to simulate the mechanical and impact response of triaxially-braided polymer matrix composites. In the analytical model, the triaxial braid architecture is simulated by using four parallel shell elements, each of which is modeled as a laminated composite. For the current analytical approach, each shell element is considered to be a smeared homogeneous material. The commercial transient dynamic finite element code LS-DYNA is used to conduct the simulations, and a continuum damage mechanics model internal to LS-DYNA is used as the material constitutive model. The constitutive model requires stiffness and strength properties of an equivalent unidirectional composite. Simplified micromechanics methods are used to determine the equivalent stiffness properties, and results from coupon level tests on the braided composite are utilized to back out the required strength properties. Simulations of quasi-static coupon tests of several representative braided composites are conducted to demonstrate the correlation of the model. Impact simulations of a represented braided composites are conducted to demonstrate the capability of the model to predict the penetration velocity and damage patterns obtained experimentally.

Goldberg, Robert K.↗
NASA NTRS2020

Jig Twist Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft and High-Fidelity CFD Validation

This paper presents a jig twist optimization study of Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft using an in-house developed aero-structural analysis solver VSPAERO coupled to BEAM3D. A vortex-lattice model of the TTBW model is developed, and a transonic and viscous flow correction method is implemented in the VSPAERO model to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. Also, a structural dynamic finite-element model of the TTBW aircraft is developed. This finite-element model includes the geometric nonlinear effect due to the tension in the struts which causes a deflection-dependent nonlinear stiffness. The VSPAERO model is coupled to the corresponding finite-element model to provide a rapid aero-structural analysis. A design flight condition corresponding to Mach 0.745 at 42000 ft is selected for the TTBW aircraft jig twist optimization to reduce the drag coefficient. After the design is implemented, the drag coefficient of the twist optimized TTBW aircraft is reduced about 8 counts. At the end, a high-fidelity CFD solver FUN3D is used to validate the design.

BEAM3D↗
NASA NTRS2020

Jig Twist Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft and High-Fidelity CFD Validation

This paper presents a jig twist optimization study of Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft using an in-house developed aero-structural analysis solver VSPAERO coupled to BEAM3D. A vortex-lattice model of the TTBW model is developed, and a transonic and viscous flow correction method is implemented in the VSPAERO model to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. Also, a structural dynamic finite-element model of the TTBW aircraft is developed. This finite-element model includes the geometric nonlinear effect due to the tension in the struts which causes a deflection-dependent nonlinear stiffness. The VSPAERO model is coupled to the corresponding finite-element model to provide a rapid aero-structural analysis. A flight condition corresponding to Mach 0.745 at 42000 ft is selected for the TTBW aircraft jig twist optimization to reduce the drag coefficient. After the design is implemented, the drag coefficient of the twist optimized TTBW aircraft is reduced about 8 counts. At the end, a high-fidelity CFD solver FUN3D is used to validate the design.

Xiong, Juntao↗
NASA NTRSDate not supplied

Multi-point Jig Twist Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft and High-Fidelity CFD Validation

This paper presents a multi-point jig twist optimization study of the Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft using an in-house developed aero-structural analysis solver VSPAERO coupled to BEAM3D. A vortex-lattice model of the TTBW model is developed, and a transonic small disturbance /integral boundary layer correction method is implemented in the VSPAERO model to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. Also, a structural dynamic finite-element model of the TTBW aircraft is developed. This finite-element model includes the geometric nonlinear effect due to the tension in the struts which causes a deflection-dependent nonlinear stiffness. The VSPAERO model is coupled to the corresponding finite-element model to provide a rapid aero-structural analysis. The VSPAERO model has been validated against wind tunnel test data and FUN3D CFD simulation data. Three different flight conditions corresponding to Mach 0.745 at 40,000 ft are selected for the TTBW aircraft jig twist optimization to reduce the drag coefficients at the design and off-design cruise lift coefficients. The preliminary optimization results show that the TTBW aircraft with the optimized jig twist achieves a drag reduction of about 9 counts, 7 counts, and8 counts corresponding to the lift coefficients 0.68, 0.73, and 0.78, respectively. A high-fidelity CFD solver FUN3D is used to validate the jig twist optimization.

Multi-point↗