Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ductility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

The comparative strength and fracture toughness properties of commercial 95W-3.5Ni1.5Fe and 95W-3.5Ni1.5Cu tungsten heavy alloys

Due to the sharp surface cracks resulting from high and cyclic thermal loads, fracture toughness is a crucial property for fusion divertor materials. Tungsten heavy alloys (WHA) have emerged as a leading candidate for plasma facing component applications. Both the WNiFe and WNiCu WHAs have been considered. However, there is no fracture toughness data in the literature on the WNiCu WHA. Therefore, maximum load elastic–plastic fracture toughness (K Jm ) of a commercial 95W-3.5Ni1.5Cu (NiCu) WHA plate is reported here for the first time. The NiCu WHA K Jm is compared to a corresponding K Jm for commercial 95W-3.5Ni1.5Fe (NiFe) WHA, along with comparisons of their respective microstructures, microhardness, and tensile properties. Although their room temperature yield strengths are similar (≈ 600 MPa), the NiFe WHA has higher ultimate stress (818 MPa vs. 642 MPa) and total elongation (8% vs. 1.2%) compared to the NiCu WHA. Most notably, the room temperature elastic–plastic K Jm for the NiFe WHA of ≈ 80 ± 8 MPa$\sqrt{m}$, is nearly twice that of the NiCu WHA at ≈ 47 ± 4 MPa$\sqrt{m}$. Further, while the NiFe WHA experienced stable ductile tearing, the crack propagated unstably (approximately elastically) after reaching the maximum load in the NiCu WHA. The higher K Jm of the NiFe WHA is attributed to its higher flow stress and ductility, along with the energy dissipation and microcrack dilatational stress shielding, provided by a wide distribution of arrested process-zone microcracks, which are largely absent in the NiCu WHA. Since, the 95W-NiFe WHA has distinctly better mechanical properties than 95W-NiCu WHA, it is a more suitable candidate for the fusion reactor application.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

A novel stress-induced martensitic transformation in a single-phase refractory high-entropy alloy

High-entropy alloys (HEAs) provide a new perspective to design metastable alloys with the stress-induced martensitic transformation (SIMT) for overcoming the strength-ductility trade-off. Here, we report a novel SIMT, orthorhombic to hexagonal close-packed martensite, in a single orthorhombic refractory HEA (Ti 16 Zr 35 Hf 35 Ta 14 RHEA), showing a good yield strength-ductility matching. The analysis of the elastic distortion energy (ΔE els ) of Ti 16 Zr 35 Hf 35 Ta 14 and several other RHEAs reveals that severe lattice distortion is a key factor which causes this SIMT. Combined the “d-electron alloy design” approach with the ΔE els , the phase configuration and SIMT path in RHEAs can be well predicted. Our work brings new insights between the lattice distortion and SIMT of RHEAs, benefiting the metastable alloy development.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Bicontinuous nanoporous design induced homogenization of strain localization in metallic glasses

Bicontinuous nanoporous metallic glasses (MG) synergize the outstanding properties of MGs and open-cell nanoporous materials. The low-density and high-specific-surface-area of bicontinuous nanoporous structures have the potential to enhance the applicability of MGs in catalysis, sensors, and lightweight structural designs. In this work, we report molecular dynamics simulations of tensile loading deformation and failure of bicontinuous nanoporous Cu 64 Zr 36 MG with 55% porosity and 4.4 nm ligament size. Results indicate an anomalous mechanical behavior featuring delocalized plastic deformation preceding ductile failure. The deformation follows two mechanisms: i) Necking of ligaments aligned with the loading direction and ii) progressive alignment of randomly oriented ligaments. Failure occurs at 0.16 strain, following massive rupture of ligaments. This work indicates that a bicontinuous nanoporous design is able to effectively delocalize strain localization in a MG due to a combination of size effect on the ductility of MGs resulting in nano ligaments necking and progressive asynchronous alignment of ligaments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A boundary-based approach to the multiscale microstructural characterization of a W-Ni-Fe tungsten heavy alloy

Here, a combination electron backscattered diffraction and transmission electron microscopy based approach has been implemented to study the effects of purposefully introduced anisotropy in a tungsten heavy alloy (WHA) through hot-rolling. Particular attention has been paid to changes in number and proportion of various boundary types from a quantitative standpoint; incorporating qualitative behavioral observations from prior analyses to generate experimentally-validated bases for the examination and application of a microstructure which exhibits an optimal balance of strength and ductility. It is asserted that a combination of increased temperatures during rolling and additional isothermal hold time for the post-rolling annealing steps may lead to a reduction in unfavorable textural components due to rolling in the W-phase and a decrease in premature fracture due to W-W microcracking respectively. This is expected to further increase the proportion of interphase boundaries and improve the ductility of these rolled structures, producing a superior rolled WHA microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Rapid tempering to enhance dynamic performance of high and ultra-high strength steels

This study employed rapid, short-time duration (1 s) tempering to improve the dynamic performance of high-strength steel (HSS) and ultra-high-strength steel (UHSS), compared to quenched and conventionally (1800 s) tempered microstructures. Rapid tempering significantly improved the Charpy toughness of both steels compared to the conventionally tempered condition at an equivalent tempering parameter (TP) or hardness level. For conventionally tempered conditions, tempered martensite embrittlement was observed within the tempering temperature range of 200–400 °C, whereas rapid tempering exhibited increased Charpy toughness with increasing tempering temperature across all tempering conditions. Dynamic compression experiments indicated that rapid tempering led to improved ductility compared to the conventionally tempered condition at an equivalent TP. This work shows that the same rapid tempering strategy used for HSS is directly transferable to a higher-carbon UHSS and provides the first systematic evidence of improved strength-ductility combinations and cracking resistance under dynamic compression, supported by Kolsky bar experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of post-deposition heat treatment on microstructure and mechanical properties of NASA HR-1 cold spray coatings

The primary goal of this work was to examine the impact of heat treatment on the evolution of microstructure and mechanical properties of NASA HR-1 cold spray coatings. Coatings were produced employing a high pressure cold spray system using N2 and He process gases and the effect of process gas and deposition temperature on the microstructure and mechanical properties of the coatings was examined. Microstructural characterization was performed using optical microscopy, scanning electron microscopy, micro X-ray computed tomography, and electron backscatter diffraction. NASA HR-1 coatings produced with He process gas exhibited improved plastic deformation and resulted in the lowest porosity compared to those deposited with N2 process gas. All coatings showed brittle failure with limited ductility in the as-deposited condition. Heat treatment of the NASA HR-1 cold spray coatings was performed at 550°C and 950°C for 1 h to improve the mechanical strength of the coatings. Heat treatment improved the particle bonding and enhanced the mechanical properties of the cold spray coatings. Heat treatment performed at 550°C resulted in higher mechanical strength of coatings, whereas the heat treatment performed at 950°C resulted in recrystallized microstructure and improved ductility of the coatings. However, heat treatment at 950°C resulted in forming the Eta (η) phase and Ni-Ti intermetallics in all the NASA HR-1 cold spray coatings. Here, the overall results suggest that using He as process gas contributed to reduced porosity and enhanced mechanical properties of the cold spray coatings.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Toward accurate prediction of partial-penetration laser weld performance informed by three-dimensional characterization – Part II: μCT based finite element simulations

The mechanical behavior of partial-penetration laser welds exhibits significant variability in engineering quantities such as strength and apparent ductility. Understanding the root cause of this variability is important when using such welds in engineering designs. In Part II of this work, we develop finite element simulations with geometry derived from micro-computed tomography (μCT) scans of partial-penetration 304L stainless steel laser welds that were analyzed in Part I. We use these models to study the effects of the welds’ small-scale geometry, including porosity and weld depth variability, on the structural performance metrics of weld ductility and strength under quasi-static tensile loading. We show that this small-scale geometry is the primary cause of the observed variability for these mechanical response quantities. Additionally, we explore the sensitivity of model results to the conversion of the μCT data to discretized model geometry using different segmentation algorithms, and to the effect of small-scale geometry simplifications for pore shape and weld root texture. The modeling approach outlined and results of this work may be applicable to other material systems with small-scale geometric features and defects, such as additively manufactured materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Detecting Thermally Induced Spinodal Decomposition with Picosecond Ultrasonics in Cast Austenitic Stainless Steels

Given the existential climate crisis faced by mankind and the world, the lifetime and sustainability of nuclear reactors as a carbon-free source of renewable energy depend on the susceptibility of their structural components to environmental degradation. In particular, critical components for light water reactors (LWRs) evolve over decades in service, losing ductility and toughness due to thermal and irradiation aging. Techniques to monitor their health cannot be easily applied in the field due to their destructive, expensive, or immobile nature. Thus, non-destructive evaluation (NDE) methods are sought to monitor and evaluate the health of major LWR components such as core barrels, steam generator tubes, or primary coolant pipes and are often required by policy, such as NRC policy #10-CFR-50.65. In this work we demonstrate the use of gigahertz, non-contact ultrasonics to gauge the state of cast austenitic stainless steels (CASS), used in some of the largest components in LWR primary systems. We do so by linking changes in their surface acoustic wave (SAW) characteristics using transient grating spectroscopy (TGS) to transmission electron microscopy (TEM)-verified evidence of spinodal decomposition and G-phase precipitation. In this thesis, thermal aging is shown to induce SAW peak splitting in spinodally decomposed CASS alloys, correlated strongly with lowered toughness and decreased ductility. Furthermore, statistical testing on the number of SAW peak splits observed show that the second SAW peak significantly appears more frequently and is significantly different in frequency in comparison to counts and frequencies measured in unaged specimens. The ability of this technique to non-destructively detect microstructural degradation at a distance in a predictive manner in the case of CASS motivates extending gigahertz ultrasonics to detect other LWR material degradation modes as an in-vessel inspection technique, such as reactor pressure vessel (RPV) embrittlement. This allows for the greater use of NDE techniques for confident monitoring of LWR structural material health to 80 years and beyond, saving costs by minimizing structural replacements until needed and maximizing energy production by preventing early decommission until necessary.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Ab Initio Simulation of Medium-Range Ordering in Ionic Glass Electrolytes LiSiPON and LiNaSiPON

Ionic glasses can exhibit a unique combination of optical transparency, electronic resistivity, ionic conductivity, and mechanical ductility. The origin of the relatively high ionic conductivity and ductility is poorly understood. Recently, these ionic glasses were found to have medium-range ordering (MRO) similar to that of metallic glasses. This MRO significantly impacts the properties of metallic glasses and is also expected to significantly impact the properties of ionic glasses. Here, this work used ab initio molecular dynamics (AIMD) simulations to study the effect of ionic glass composition on the MRO. The AIMD models showed that the degree of MRO increased as the temperature of the LiSiPON ionic glass decreased. The modeling also showed that the MRO is suppressed when 50% of Li is substituted with Na. This work lays the foundation for using AIMD to identify clear structure–property relationships in ionic glasses, allowing their properties to be optimized.

Osetsky, Yuri N. [Oak Ridge National Laboratory (O↗
DOE OSTI2022

Subduction, Underplating, and Return Flow Recorded in the Cycladic Blueschist Unit Exposed on Syros, Greece

Exhumed high-pressure/low-temperature (HP/LT) metamorphic rocks provide insights into deep (~20–70 km) subduction interface dynamics. On Syros Island (Cyclades, Greece), the Cycladic Blueschist Unit preserves blueschist-to-eclogite facies oceanic- and continental-affinity rocks that record the structural and thermal evolution linked to Eocene subduction. Despite decades of research, the metamorphic and deformation history (P-T-D) and timing of subduction and exhumation are matters of ongoing discussion. We suggest that Syros comprises three coherent tectonic slices and that each slice underwent subduction, underplating, and syn-subduction return flow along similar P-T trajectories, but at progressively younger times. Subduction and exhumation are distinguished by lineations and ductile fold axis orientations, and are kinematically consistent with previous studies that document top-to-the-S-SW shear (prograde-to-peak subduction), top-to-the-NE shear (blueschist facies exhumation), and then E-W coaxial stretching (greenschist facies exhumation). Amphibole zonations record cooling during decompression, indicating return flow above a cold slab. Multi-mineral Rb-Sr isochrons and compiled metamorphic geochronology show that the three slices record distinct stages of peak subduction (53–52, ~50, and 45 Ma) that young with structural depth. Retrograde blueschist and greenschist facies fabrics span ~50–40 and ~43–20 Ma, respectively, and also young with structural depth. Synthesized data sets support a revised tectonic framework for Syros, involving subduction of structurally distinct coherent slices and simultaneous return flow of previously accreted tectonic slices in the subduction channel shear zone. Distributed, ductile, dominantly coaxial return flow in an Eocene-Oligocene subduction channel proceeded at rates of ~1.5–5 mm/yr and accommodated ~80% of the total exhumation of this HP/LT complex.

58 GEOSCIENCES↗
DOE OSTI2023

Grain refinement in titanium prevents low temperature oxygen embrittlement

Interstitial oxygen embrittles titanium, particularly at cryogenic temperatures, which necessitates a stringent control of oxygen content in fabricating titanium and its alloys. Here, we propose a structural strategy, via grain refinement, to alleviate this problem. Compared to a coarse-grained counterpart that is extremely brittle at 77 K, the uniform elongation of an ultrafine-grained (UFG) microstructure (grain size ~ 2.0 µm) in Ti-0.3wt.%O is successfully increased by an order of magnitude, maintaining an ultrahigh yield strength inherent to the UFG microstructure. This unique strength-ductility synergy in UFG Ti-0.3wt.%O is achieved via the combined effects of diluted grain boundary segregation of oxygen that helps to improve the grain boundary cohesive energy and enhanced dislocation activities that contribute to the excellent strain hardening ability. The present strategy will not only boost the potential applications of high strength Ti-O alloys at low temperatures, but can also be applied to other alloy systems, where interstitial solution hardening results into an undesirable loss of ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Hierarchical Eutectoid Nano-lamellar Decomposition in an Al 0.3 CoFeNi Complex Concentrated Alloy

This paper reports a novel eutectoid nano-lamellar (FCC + L1 2 )/(BCC + B2) microstructure that has been discovered in a relatively simple Al 0.3 CoFeNi high entropy alloy (HEA) or complex concentrated alloy (CCA). This novel eutectoid nano-lamellar microstructure presumably results from the complex interplay between Al-mediated lattice distortion (due to its larger atomic radius) in a face-centered cubic (FCC) CoFeNi solid solution, and a chemical ordering tendency leading to precipitation of ordered phases such as L1 2 and B2. This eutectoid microstructure is a result of solid-state decomposition of the FCC matrix and therefore distinct from the commonly reported eutectic microstructure in HEAs which results from solidification. This novel nano-lamellar microstructure exhibits a tensile yield strength of 1074 MPa with a reasonable ductility of 8%. The same alloy can be tuned to form a more damage-tolerant FCC + B2 microstructure, retaining high tensile yield stress (~900 MPa) with appreciable tensile ductility (>20%), via annealing at 700 °C. Such tunability of microstructures with dramatically different mechanical properties can be effectively engineered in the same CCA, by exploiting the complex interplay between ordering tendencies and lattice distortion.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Correlating work hardening with co-activation of stacking fault strengthening and transformation in a high entropy alloy using in-situ neutron diffraction

Transformation induced plasticity (TRIP) leads to enhancements in ductility in low stacking fault energy (SFE) alloys, however to achieve an unconventional increase in strength simultaneously, there must be barriers to dislocation motion. While stacking faults (SFs) contribute to strengthening by impeding dislocation motion, the contribution of SF strengthening to work hardening during deformation is not well understood; as compared to dislocation slip, twinning induced plasticity (TWIP) and TRIP. Thus, we used in-situ neutron diffraction to correlate SF strengthening to work hardening behavior in a low SFE Fe 40 Mn 20 Cr 15 Co 20 Si 5 (at%) high entropy alloy, SFE ~ 6.31 mJ m –2 . Cooperative activation of multiple mechanisms was indicated by increases in SF strengthening and γ-f.c.c. → ε-h.c.p. transformation leading to a simultaneous increase in strength and ductility. The present study demonstrates the application of in-situ, neutron or X-ray, diffraction techniques to correlating SF strengthening to work hardening.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Co-introduction of precipitate hardening and TRIP in a TWIP high-entropy alloy using friction stir alloying

Tuning deformation mechanisms is imperative to overcome the well-known strength-ductility paradigm. Twinning-induced plasticity (TWIP), transformation-induced plasticity (TRIP) and precipitate hardening have been investigated separately and have been altered to achieve exceptional strength or ductility in several alloy systems. In this study, we use a novel solid-state alloying method—friction stir alloying (FSA)—to tune the microstructure, and a composition of a TWIP high-entropy alloy by adding Ti, and thus activating site-specific deformation mechanisms that occur concomitantly in a single alloy. During the FSA process, grains of the as-cast face-centered cubic matrix were refined by high-temperature severe plastic deformation and, subsequently, a new alloy composition was obtained by dissolving Ti into the matrix. After annealing the FSA specimen at 900 °C, hard Ni–Ti rich precipitates formed to strengthen the alloy. An additional result was a Ni-depleted region in the vicinity of newly-formed precipitates. The reduction in Ni locally reduced the stacking fault energy, thus inducing TRIP-based deformation while the remaining matrix still deformed as a result of TWIP. Our current approach presents a novel microstructural architecture to design alloys, an approach that combines and optimizes local compositions such that multiple deformation mechanisms can be activated to enhance engineering properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Performance of hybrid Innegra-carbon fiber composites

Abstract In this work material synergy with high stiffness carbon fiber with ductile high strength polypropylene fiber (Innegra S), (referred to as Innegra, herein) have been evaluated in a range of laminate designs. Both woven and discontinuous carbon fiber have been considered. The discontinuous fibers are based on three-dimensional deposition (3DEP) (referred to as 3DEP, herein) carbon fiber preform process. Eleven (11) variants of Innegra-carbon fiber hybrid laminates were investigated for tensile, flexure, compression, in-plane shear and low velocity impact response. The effect of position of Innegra within the laminate was studied and found to influence strength and stiffness properties. In terms of overall trends, Innegra provides upward of 18% improvement in strain (ductility) to the composite and eliminates brittle fracture of carbon fiber. The moduli trends follow the proportionality of Innegra fiber to carbon fiber plies. However, the strength is controlled by the interface between Innegra and carbon fiber. The primary failure mode in tension and compression is via onset of debonding between Innegra and carbon fiber. The 3DEP carbon fiber constituents provided highest values of in-plane shear indicating that three-dimensional (3D) network of carbon fiber provides higher shear resistance. The Innegra intensive variants exhibited superior energy absorption under low velocity impact, at energy levels 15–60 J. This work provides insight for designers to incorporate Innegra and carbon fiber hybrids in composite structures.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Solidification cracking of laser melted commercial-purity tungsten

The high melting temperature of tungsten (W) makes it an attractive candidate for energy generation applications; however, its use is limited by its poor ductility at low temperatures. This limitation affects even melt-based additive manufacturing (AM) processes such as laser powder bed fusion (PBF-LB), with as-fabricated pure W exhibiting both longitudinal and transverse cracks. Metallurgical and processing factors that affect these cracks are still being explored. This work utilizes powderless single-tracks on pure W plates made over a range of power and velocity combinations in three unique PBF-LB setups: one with flowing argon, one with continuous vacuum, and an in situ high-speed synchrotron X-ray radiography setup. Each had different oxygen activities in their build environments. Longitudinal cracks with oxides appearing to exude from the crack were found for tracks deposited in a build environment with argon shield gas, while no such cracks were observed for builds conducted in vacuum. A calculation showed that direct oxygen ingress into the melt pool from the build environment is negligible when argon shield gas is present. Thus, incorporation of spatter is a likely mechanism for oxygen ingress into the melt pool. Radiography showed extensive keyholing, spatter generation, and crack formation at keyhole porosity. A heat transfer calculation showed the crack formation time was consistent with cooling below its ductile-to-brittle transition (DBT) temperature. This work identifies solidification cracking as a feasible mechanism in pure W beyond the well-known DBT related cracking.

Materials science↗
DOE OSTI2024

Crack mitigation in additively manufactured AlCrFe 2 Ni 2 high-entropy alloys through engineering phase transformation pathway

The far-from-equilibrium solidification during additive manufacturing often creates large residual stresses that induce solid-state cracking. Here we present a strategy to suppress solid-state cracking in an additively manufactured AlCrFe 2 Ni 2 high-entropy alloy via engineering phase transformation pathway. We investigate the solidification microstructures formed during laser powder-bed fusion and directed energy deposition, encompassing a broad range of cooling rates. At high cooling rates (10 4 –10 6 K/s), we observe a single-phase BCC/B2 microstructure that is susceptible to solid-state cracking. At low cooling rates (10 2 –10 4 K/s), FCC phase precipitates out from the BCC/B2 matrix, resulting in enhanced ductility (~10 %) and resistance to solid-state cracking. Site-specific residual stress/strain analysis reveals that the ductile FCC phase can largely accommodate residual stresses, a feature which helps relieve residual strains within the BCC/B2 phase to prevent cracking. Our work underscores the value of exploiting the toolbox of phase transformation pathway engineering for material design during additive manufacturing.

36 MATERIALS SCIENCE↗